Material Safety Data Sheet

Transcription

1 Page: 1 1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER Product Name FULLERTRADE GAP FILLER Company Name H.B. FULLER COMPANY (ABN ) Address Red Gum Drive Dandenong South Victoria 317 Australia Emergency Tel. AUS: (or IDD ), NZ: (Or IDD ) Telephone/Fax Tel: Customer Service Toll Free Numbers: Australia ; Number Recommended Use Patching gaps around skirting boards, architraves, cornices, ceramic tiles, window frames and general purpose fit out finishing. Other This MSDS summarises at the date issue our best knowledge the health and safety hazard information the product, and in particular, how to safely handle and use the product in the workplace. Since H.B. Fuller Company Australia Pty Ltd cannot anticipate or control the conditions under which the product may be used, each user must, prior to usage, review this MSDS in the context how the user intends to handle and use the product in the workplace. If clarification or further information is needed to ensure that an appropriate assessment can be made, the user should contact this company. Our responsibility for the products sold is subject to our standard terms and conditions, a copy which is sent to our customers and is also available on request. 2. HAZARDS IDENTIFICATION Hazard Classification Not classified as Hazardous according to criteria National Occupational Health & Safety Commission, Australia (NOHSC). Not classified as Dangerous Goods according to the Australian Code for the Transport Dangerous Goods by Road and Rail. Safety Phrase(s) Not classified as Hazardous according to the Hazardous Substances (Minimum Degrees Hazard) Regulations 2001, New Zealand. Not classified as Dangerous Goods for transport, according to the NZS 433:2007 Transport Dangerous Goods on Land. S24 Avoid contact with skin. 3. COMPOSITION/INFORMATION ON INGREDIENTS Ingredients Other Name 4. FIRST AID MEASURES CAS Proportion Hazard Symbol Calcium Carbonate % Styrene acrylic % latex -chloro-2-methyl < H-isothiazol-3- one and 2-methyl-2H-isoth iazol-3-one (3:1) Ingredients determined not to be hazardous. Balance The acrylic polymer in this product may contain residual trace amounts butyl acrylate, formaldehyde, ethyl benzene, styrene and n-butanol. Risk Phrase

2 Page: 2 Inhalation Ingestion Skin Eye First Aid Facilities Advice to Doctor Other. FIRE FIGHTING MEASURES Suitable Extinguishing Media Hazards from Combustion Products Precautions in connection with Fire If inhaled, remove affected person from contaminated area. Keep at rest until recovered. If symptoms persist seek medical attention. Do not induce vomiting. Wash out mouth thoroughly with water. If symptoms develop seek medical attention. Wash affected area thoroughly with soap and water. Seek medical attention. If in eyes, hold eyelids apart and flush the eyes continuously with running water. Continue flushing for several minutes until all contaminants are washed out completely. Seek medical attention. Eyewash and normal washroom facilities. Treat symptomatically. For advice in an emergency, contact a Poisons Centre (Phone Australia ; New Zealand 0800 POISON / ) or a doctor at once. Use water fog, foam, carbon dioxide or dry chemical powder. Under fire conditions this product may emit toxic and/or irritating fumes and gases including oxides nitrogen, carbon monoxide and carbon dioxide. Fire fighters should wear Self-Contained Breathing Apparatus (SCBA) operated in positive pressure mode and full protective clothing to prevent exposure to vapours or fumes. Water spray may be used to cool down heat-exposed containers. 6. ACCIDENTAL RELEASE MEASURES Emergency Procedures 7. HANDLING AND STORAGE Precautions for Safe Handling Conditions for Safe Storage Wear appropriate personal protective equipment and clothing to minimise exposure. Increase ventilation. If possible contain the spill. Place inert absorbent material onto spillage. Collect the material and place into a suitable labelled container. Do not dilute material but contain. Dispose waste according to federal, Environmental Protection Authority and state regulations. If the spillage enters the waterways contact the Environmental Protection Authority, or your local Waste Management Authority. Use only in a well ventilated area. Keep containers sealed when not in use. Prevent the build up mists or vapours in the work atmosphere. Avoid inhalation vapours and mists, and skin or eye contact. Maintain high standards personal hygiene ie. Washing hands prior to eating, drinking, smoking or using toilet facilities. Store in a cool, dry, well-ventilated area, out direct sunlight. Do not store below C. Store in suitable, labelled containers. Keep containers closed when not in use. Ensure that storage conditions comply with applicable local and national regulations. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION National Exposure Standards No exposure standards have been established for the mixture by the Australian National Occupational Health & Safety Commission (NOHSC) or the Occupational Safety and Health Service (OSH) the New Zealand Department Labour. The acrylic polymer in this product may contain residual trace amounts butyl acrylate, formaldehyde, ethyl benzene, styrene and n-butanol. The available exposure limits for trace ingredients are listed below: National Occupational Health And Safety Commission (NOHSC), Australia Exposure Standards: Substance TWA STEL NOTICES ppm mg/m³ ppm mg/m³

3 Page: 3 Biological Limit Values Engineering Controls Respiratory Protection Eye Protection Hand Protection Body Protection Ethyl benzene Styrene N-butanol 0 12(Peak) - - Sk Butyl acrylate Stoddard solvent New Zealand Occupational Safety and Health Service (OSH) Workplace Exposure Standards: Substance TWA STEL NOTICES ppm mg/m³ ppm mg/m³ Ethyl benzene Styrene Sk N-butanol 0 10(Ceiling) - - Sk Butyl acrylate Sen Stoddard solvent TWA (Time Weighted Average): The average airborne concentration a particular substance when calculated over a normal eight-hour working day, for a five-day week. STEL (Short Term Exposure Limit): The average airborne concentration over a 1 minute period which should not be exceeded at any time during a normal eight-hour workday. Peak Limitation: A ceiling concentration which should not be exceeded over a measurement period which should be as short as possible but not exceeding 1 minutes. Ceiling: A concentration that should not be exceeded during any part the working day. 'Sk' Notice: Absorption through the skin may be a significant source exposure. The exposure standard is invalidated if such contact should occur. 'Sen' Notice: The substance may cause sensitisation by skin contact or by inhalation No biological limits allocated. Provide sufficient ventilation to keep airborne levels as low as possible. Where vapours or mists are generated, particularly in enclosed areas, and natural ventilation is inadequate, a local exhaust ventilation system is required. If engineering controls are not effective in controlling airborne exposure then an approved respirator with a replaceable mist/particulate filter should be used. Reference should be made to Australian/New Zealand Standards AS/NZS 171, Selection, Use and Maintenance Respiratory Protective Devices; and AS/NZS 1716, Respiratory Protective Devices, in order to make any necessary changes for individual circumstances. Safety glasses with side shields or chemical goggles should be worn. Final choice appropriate eye/face protection will vary according to individual circumstances. Eye protection devices should conform with Australian/New Zealand Standard AS/NZS Eye Protectors for Industrial Applications. Wear gloves impervious material. Final choice appropriate gloves will vary according to individual circumstances i.e. methods handling or according to risk assessments undertaken. Reference should be made to AS/NZS : Occupational protective gloves - Selection, use and maintenance. Suitable protective workwear, e.g. cotton overalls buttoned at neck and wrist is recommended. Chemical resistant apron is recommended where large quantities are handled. Industrial clothing should conform to the specifications detailed in AS/NZS 2919: Industrial clothing. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Thick white paste.

4 Page: 4 Odour Melting Point Boiling Point Solubility in Water Characteristic styrene odour Fully miscible Specific Gravity Approx. 1.6 ph Value Vapour Pressure Vapour Density (Air=1) Volatile Component Flash Point Flammability Auto-Ignition Temperature Flammable Limits - Lower Flammable Limits - Upper Dynamic Viscosity VOC (California South coast air quality management rule 1168): 22 g/litre. Not flammable 900,000-1,200,000 cp 10. STABILITY AND REACTIVITY Chemical Stability Conditions to Avoid Incompatible Materials Hazardous Decomposition Products Hazardous Polymerization Stable under normal conditions storage and handling. Moisture.. Under fire conditions this product may emit toxic and/or irritating fumes, smoke and gases including oxides nitrogen, carbon monoxide and carbon dioxide. Will not occur. 11. TOXICOLOGICAL INFORMATION Toxicology Inhalation Ingestion Skin Eye Chronic Effects 12. ECOLOGICAL INFORMATION Ecotoxicity Persistence / Degradability No toxicity data available for this product. Inhalation product vapours may cause irritation the nose, throat and respiratory system. Ingestion this product may irritate the gastric tract causing nausea and vomiting and cause abdominal pains. May be irritating to skin. The symptoms may include redness, itching and swelling. May cause sensitization by skin contact for sensitive individuals. May be irritating to eyes. The symptoms may include redness, itching and tearing. Repeated or prolonged skin contact may lead to irritation.

5 Page: Mobility Environ. Protection Prevent this material entering waterways, drains and sewers. 13. DISPOSAL CONSIDERATIONS Disposal Considerations 14. TRANSPORT INFORMATION Transport 1. REGULATORY INFORMATION Regulatory Poisons Schedule National and or International Regulatory 16. OTHER INFORMATION Date preparation or last revision MSDS Contact Person/Point Dispose waste according to applicable local and national regulations. Not classified as Dangerous Goods according to the Australian Code for the Transport Dangerous Goods by Road and Rail. (7th edition) Not classified as Dangerous Goods for transport according to the NZS 433:2007 Transport Dangerous Goods on Land. Not classified as Hazardous according to criteria National Occupational Health & Safety Commission (NOHSC), Australia. Not classified as a Scheduled Poison according to the Standard for the Uniform Scheduling Drugs and Poisons (SUSDP). Not Scheduled Not Classified as Hazardous according to the New Zealand Hazardous Substances (Minimum Degrees Hazard) Regulations MSDS Created: March 2010 For advice in an emergency contact: (or IDD ) (or IDD )...End Of MSDS... Copyright ACOHS Pty Ltd Copyright in the source code the HTML, PDF, XML, XFO and any other electronic files rendered by an Infosafe system for Infosafe MSDS displayed is the intellectual property Acohs Pty Ltd. Copyright in the layout, presentation and appearance each Infosafe MSDS displayed is the intellectual property Acohs Pty Ltd. The compilation MSDS's displayed is the intellectual property Acohs Pty Ltd. Copying any MSDS displayed is permitted for personal use only and otherwise is not permitted. In particular the MSDS's displayed cannot be copied for the purpose sale or licence or for inclusion as part a collection MSDS without the express written consent Acohs Pty Ltd.