CONTRACTOR REQUEST FOR COMMISSIONING
|
|
- Kory Elliott
- 5 years ago
- Views:
Transcription
1 CONTRACTOR REQUEST FOR COMMISSIONING PCMS-A
2 PRE-COMMISSIONING METHOD STATEMENT - PHASE PRESSURE TEST SPECIFICATION IMPORTANT - OXYGEN FREE NITROGEN ONLY (OFN) bar 0 psig Minimum of 0 minutes bar 0 psig Minimum of 0 minutes bar 70 psig Minimum of 0 minutes bar 60 psig bar 70 psig Stress test to prove the integrity of the complete installation. This test should last for a period of hour. Lower system pressure upon confirmation that item No. has been successful. Minimum test period is hrs. NOTE - Oxygen Free Nitrogen will vary in pressure due to temperature change at a rate of.6 psig per F. PRE-COMMISSIONING METHOD STATEMENT - PHASE TRIPLE EVACUATION PROCEDURE A Micron or Torr gauge must be used for this procedure. Discharge the oxygen-free nitrogen and evacuate the system to a reading of 8000 Microns (8 Torr) using all service valves. Break the vacuum by allowing nitrogen into the applicable inter-connecting pipework port connections (Example: low pressure gas pipe, high pressure gas pipe and liquid line pipe) until a positive pressure is achieved. Evacuate the system to a reading of 000 Microns ( Torr). Break the vacuum by allowing nitrogen into the applicable inter-connecting pipework port connections (Example: low pressure gas pipe, high pressure gas pipe and liquid line pipe) until a positive pressure is achieved. Evacuate the system to a reading of 00 Microns. 6 For a moisture-free system, ensure the vacuum is held without movement for a minimum of hrs. 7 If pressure loss is detected, carry out steps through 6 until no pressure loss is observed. To ensure correct system performance and reliability the above Method Statement (Phase & ) must be strictly followed. Failure to follow these guidelines will result in the warranty being voided. PCMS-A
3 CERTIFICATE OF CONFORMITY INSTALLING CONTRACTOR'S NAME CONTRACTORS FULL STREET ADDRESS PROJECT REFERENCE # PROJECT FULL STREET ADDRESS SYSTEM STRESS TESTED TO psig SYSTEM EVACUATED TO Microns SYSTEM STRESS TEST PERIOD Hrs. VACUUM HELD FOR Hrs. 70PSIG (bar) HELD FOR Hrs. Additional Comments INSTALLING CONTRACTOR'S FULL NAME INSTALLING CONTRACTOR'S SIGNATURE POSITION LENNOX VRF TRAINING REF NUMBER DATE By signing this document you are confirming that the Pre-Commissioning Phase & Phase method statements have been completed and all figures stated above are true. This document is for record-keeping purposes only and does not quarantee future warranty claims. PCMS-A
4 CONTRACTOR'S CHECKLIST PLEASE USE THIS CHECKLIST TO CONFIRM THE SYSTEM IS READY FOR THE COMMISSIONING PROCESS ITEM No DESCRIPTION Interconnecting pipework fully completed Condensate disposal system fully completed and tested Control cabling installation complete except for final connection to outdoor units Pre-commissioning method statement Phase completed Pre-commissioning method statement Phase completed Required additional refrigerant added - Add refrigerant before opening the service valves Outdoor service valves fully open Main power supply is available for all outdoor units and will be activated hrs prior to commissioning Main power supply is available for all indoor units Main power supply is available for all mode switching boxes Remote controllers installed where necessary Centralized controller installed if required Main power supply is available for centralized controller System address confirmed for all outdoor units Cerificate of conformity signed and completed Project construction plans are available and marked up as stated in commissioning documents Site conditions suitable for operating the equipment Protective covers removed from all indoor and outdoor units Building management system is not connected to or controlling the system in any way Must have member of installation team available onsite for commissioning CHECK Important notes Allow at least 7 working days after submission for a Lennox commissioning appointment Complete and "Request for Commissioning" form to vrfcomm@lennoxind.com Abortive visits due to rd party issues may result in additional costs being applied to your account Failure to give at least hrs notice to cancel a pre-arranged commissioning visit may result in additional costs being applied to your account PCMS-A
5 REQUEST FOR COMMISSIONING PROJECT REFERENCE # PROJECT FULL STREET ADDRESS INSTALLING CONTRACTORS NAME CONTRACTOR'S FULL STREET ADDRESS Requested Date for Commissioning Site Operating Times Company Representative's Name Company Representative's Contact Info Contractor's Lennox VRF ID Number Identify any specific safety requirements our personnel must adhere to during the commissioning procedure. Identify any specific safety issues we need to be aware of. Please complete form and to: vrfcomm@lennoxind.com PCMS-A
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS MODEL GS2000 / GS2001 OIL-LESS REFRIGERANT RECOVERY UNIT NATIONAL REFRIGERATION PRODUCTS 985 WHEELER WAY LANGHORNE, PA 19047 (215) 638-8909 FAX (215) 638-9270 R01099 GS2000.DOC NRP-OM-GS2000
More informationNGP-250/500 Nitrogen Generator Quick Start Guide
NGP-250/500 Nitrogen Generator Quick Start Guide Version: A July 2013 Potter Electric Signal Company, LLC 5757 Phantom Dr., Suite 125 P. O. Box 42037 Hazelwood, MO 63042 Phone: (314) 595-6900 Document
More informationDRAFT. Operating Procedures for the NPDGamma Liquid Hydrogen Target in TA-53, Building MPF-35
Operating Procedures for the NPDGamma Liquid Hydrogen Target V0.03 11/26/05 1 DRAFT Operating Procedures for the NPDGamma Liquid Hydrogen Target in TA-53, Building MPF-35 Version 0.03 November 26, 2005
More informationOxford Instruments Plasma Technology. PlasmaPro NGP80. Installation Data Sheet. Original Instructions.
Oxford Instruments Plasma Technology www.oxford-instruments.com About this data sheet This data sheet provides basic information about the installation of a tool. Floor and wall loadings Table 1 lists
More informationD R A F T. Operating Procedures for the NPDGamma Liquid Hydrogen Target at the BL 13. Version 1.00
D R A F T Operating Procedures for the NPDGamma Liquid Hydrogen Target at the BL 13 Version 1.00 October 06, 2010 Operating Procedures for the NPDGamma Liquid Hydrogen Target V1.00 6/10/10 2 Table of Content
More informationINSTRUCTIONS FOR MODELS SG3897 AND SG3898 CROSS PURGE ASSEMBLIES
INSTRUCTIONS FOR MODELS SG3897 AND SG3898 CROSS PURGE ASSEMBLIES THIS BOOKLET CONTAINS PROPRIETARY INFORMATION OF ADVANCED SPECIALTY GAS EQUIPMENT CORP. AND IS PROVIDED TO THE PURCHASER SOLELY FOR USE
More informationEU minimum requirements. Training and certification for personnel and companies
EU_AREA_EC842CERTIF EU minimum requirements on Training and certification for personnel and companies involved in installation, maintenance, inspection and repair of refrigeration, air conditioning and
More informationInformation Sheet. About this information sheet. Floor and wall loadings. Attachment of process module to floor. PlasmaPro Estrelas100
Information Sheet PlasmaPro Estrelas100 About this information sheet This data sheet provides basic information about the installation of a PlasmaPro Estrelas100 tool. Some of the information in this sheet
More informationPOWER FLUSH KIT INSTRUCTIONS
1 GENERAL INFORMATION POWER FLUSH KIT INSTRUCTIONS ACE Power Flush is an ozone-safe solvent engineered specifically for flushing refrigeration and air conditioning systems. Used exactly like the old R-11
More informationPressure Automated Calibration Equipment
GE Measurement & control Pressure Automated Calibration Equipment Safety Instructions and User Guide - K0447 PACE5000 PACE6000 K0447 Issue No. 9 1 10 1 PACE5000 1 2 3 4 5 PACE6000 2 6 7 8 3 4 5 6 7 8 9
More informationv. Size shall be specified on drawings.
SPECIFICATION FOR VACUUM INSULATED PIPING Part 1 General 1. Submittals a. After award of contract and before executing any manufacturing, shop drawings and specifications shall be submitted to the customer
More information2.0 Dates and Times Tests to be carried out starting Monday 28 Nov for completion Friday 2 Dec.
MS No: :. A 1.0 Scope of Work Preparation notes: delete column before issuing. 1.1 General Description of Works, Location & Boundaries Strength and tightness testing of Glycol System between plant room
More informationINSTALLATION INSTRUCTIONS Mode Selection Box
2018 Lennox Industries Inc. Dallas, Texas, USA V8MSBB04 Shown THIS MANUAL MUST BE LEFT WITH THE OWNER FOR FUTURE REFERENCE These instructions are intended as a general guide and do not supersede local
More informationSection 3- Repair and Calibration Procedures
Section 3- Repair and Calibration Procedures 1. Refrigerant Removal Procedures 2. Scale/PC Board Recalibration Procedure 3. PC Board Configuration Procedure of AR400 4. Scale Tare Procedure 5. Gauge Calibration
More informationMinimum standard of competence in advanced training for liquefied gas tanker cargo operations (STCW Reg V/1-2)
Minimum standard of in advanced training for liquefied gas tanker cargo operations (STCW Reg V/1-2) Column 2 Knowledge, understanding and proficiency Design and characteristics of a liquefied gas tanker
More informationSERIES 30. Spring Operated Tank Blanketing Valve PROTECTOSEAL.
SERIES 30 PROTECTOSEAL 1 2" NPT inlet and outlet standard Direct acting valve mechanism Optional flanged or threaded inlet and outlet connections available Inlet gas pressures from 10 PSIG to 200 PSIG
More informationCS Controlled Dissolved Gas assembly with optional CS Air Aspirator assembly. Installation and Operation information
CS-425-01 Controlled Dissolved Gas assembly with optional CS-603-01 Air Aspirator assembly Installation and Operation information Serial # CS-XXX Date of shipment:, 2005 Shipped to: Purchase order #: xxxxxxx
More informationInstallation, Operation, and Maintenance Manual Parker Balston Model N2-04 Nitrogen Generator
Installation, Operation, and Maintenance Manual Parker Balston Figure 1 - N2-04 Nitrogen Generator These instructions must be thoroughly read and understood before installing and operating this product.
More informationGovernment of Bermuda Department of Maritime Administration BERMUDA SHIPPING NOTICE
Government of Bermuda Department of Maritime Administration 2015 027 BERMUDA SHIPPING NOTICE Maintenance and Inspection of Fixed Carbon Dioxide Fire Extinguishing Systems Ref: SOLAS 74/88 as amended, Regulation
More informationCO 2. (R744) Service Station Presentation. Contents. Goals Basic functions Specification Recovery R477 Vacuum Charge Safety Other features Prototype
(R744) Service Station Presentation Contents Goals Basic functions Specification Recovery R477 Vacuum Charge Safety Other features Prototype Page 1 (R744) Service Station Goals Usability Full automatic
More informationRDK-408D2 Cold Head. Technical Manual. SHI-APD Cryogenics Inc Vultee Street Allentown, PA U.S.A. Revision A: September 2005
RDK-408D2 Cold Head Technical Manual SHI-APD Cryogenics Inc. 1833 Vultee Street Allentown, PA 18103-4783 U.S.A. Revision A: September 2005 (Reference SHI Manual: December 18, 2003 266404A CD32ZZ-160A)
More informationUTAS EH&S INSTRUCTION No. 036 June 2012 Revision No. 3. Purging of Flammable Gas Equipment and/or Piping (Explosion Hazard)
Purging of Flammable Gas Equipment and/or Piping (Explosion Hazard) APPLICABILITY: This EH&S Instruction applies to UTAS sites worldwide, including contractors working at UTAS facilities. The document
More informationStandard Operating Procedure
Standard Operating Procedure Use of liquid nitrogen filling station Date: 02-12-13 SOP Title: Principal Investigator: Room and Building: Lab Phone Number: Section 1 Process Use of liquid nitrogen filling
More informationVortex Dual. Refrigerant Recovery Machine
O P E R A T I N G M A N U A L Vortex Dual Refrigerant Recovery Machine Table Of Contents Safety First!.................................... 3 EPA Certification................................ 3 Product
More informationHEAD PRESSURE CONTROL VALVES
May / BULLTIN -- HAD PRSSUR CONTROL VALVS LAC-, LAC--DS, LAC- and LAC- Page / BULLTIN -- HAD PRSSUR CONTROL VALVS The LAC valves are non-adjustable head pressure control valves. They are designed to maintain
More informationPRACTICAL EXPERIENCES IN THE PRODUCTION OF INSULATION FOAMS WITH HYDROCARBON BLOWING AGENT IN DEVELOPING AND DEVELOPED COUNTRIES
PRACTICAL EXPERIENCES IN THE PRODUCTION OF INSULATION FOAMS WITH HYDROCARBON BLOWING AGENT IN DEVELOPING AND DEVELOPED COUNTRIES R I S T O O J A L A, U N I D O F O A M S E C T O R C O N S U LTA N T SAFETY
More informationOPERATING INSTRUCTIONS Sherlock Chamber Testing System
OPERATING INSTRUCTIONS Sherlock Chamber Testing System Arrangement Equipment Kit FL90 & FL100 Corbel Test Plate with Gasket Seal S8, S14, S15 & S16 Sump Test Plate with Gasket Seal S7 & S5 Chamber Test
More informationGUIDELINES. Systems. Pressure. Guidelines Acceptance of equipment, establishment of safe operating limits and fitness for service
GUIDELINES Pressure Systems Guidelines Acceptance of equipment, establishment of safe operating limits and fitness for service Document Reference: PSG 16 Issue 04 Dated 13/09/16 The Safety Assessment Federation
More informationInstallation Manual. BC Box Modification with Port Isolation
Issue 2 BC Box Modification with Port Isolation Installation Manual Instructions for :- BC Box Modification with Port Isolation Models : KS8-CMB-P-V-G1 / KS8-CMB-P-V-GB1 / KS8-CMB-P-V-GA1 / KS8-CMB-P-V-HA1
More informationOperating Guidelines for PermSelect Modules Liquid Contacting
Operating Guidelines for PermSelect Modules Liquid Contacting PermSelect PDMSXA-2500 (0.25m 2 ) PermSelect PDMSXA-7500 (0.75m 2 ) PermSelect PDMSXA-1.0 (1m 2 ) PermSelect PDMSXA-2.1 (2.1m 2 ) PermSelect
More informationDEOX FPS 1 CORRISION INHIBITING SYSTEM O&M MANUAL. Revision 2 Date 02/04/16
DEOX FPS 1 CORRISION INHIBITING SYSTEM O&M MANUAL Revision 2 Date 02/04/16 Copyrighted All Rights Reserved 2016 REVISION HISTORY Revision Revision Approved Approval # Date By Date 0 2/27/15 J. Nguyen 3/2/15
More informationASME and PED Requirements for Drum Level Instrumentation. Presented by: Amir Hedayatnia Clark-Reliance Corp.
ASME and PED Requirements for Drum Level Instrumentation 2017 Presented by: Amir Hedayatnia Clark-Reliance Corp. Topics Gage Glasses and Remote Reading Instruments ASME Code Section I Requirements for
More informationBest Practices for Installation of Gaseous Sample Pumps
Best Practices for Installation of Gaseous Sample Pumps Goal of the Gas Sample Pump Transport a clean, reliable, sample of the process gas to the analyzer, in the safest and easiest way possible, to ensure
More informationLow GWP Refrigerants. Guidance on minimum requirements for contractors training & certification
Low GWP Refrigerants Guidance on minimum requirements for contractors training & certification October 2012 Revision 1 DISCLAIMER AREA does not assume liability for any statements made in this paper or
More informationINSTRUCTIONS FOR MODELS UPH & UPHS HIGH FLOW, HIGH PURITY GAS REGULATORS
INSTRUCTIONS FOR MODELS UPH & UPHS HIGH FLOW, HIGH PURITY GAS REGULATORS THIS BOOKLET CONTAINS PROPRIETARY INFORMATION OF ADVANCED SPECIALTY GAS EQUIPMENT CORP. AND IS PROVIDED TO THE PURCHASER SOLELY
More informationSTS 650 PRESSURE EQUIPMENT
Hunter Water Corporation ABN 46 228 513 446 Standard Technical Specification for: STS 650 PRESSURE EQUIPMENT This Standard Technical Specification (STS) was developed by Hunter Water Corporation to be
More informationVTL VFL VCL. Low Profile Series V RIGGING & ASSEMBLY INSTRUCTIONS
VTL VFL VCL Low Profile Series V RIGGING & ASSEMBLY INSTRUCTIONS Low Profile Series VL units should be rigged and installed as outlined in this bulletin. These procedures should be thoroughly reviewed
More informationOperating Instructions in compliance with Pressure Equipment Directive 2014/68/EU. FAS Brass Check Valve RDL
Operating Instructions in compliance with Pressure Equipment Directive 2014/68/EU FAS Brass Check Valve RDL Please read these operating instructions carefully to ensure a safe operation and keep the same
More informationVacuum Insulated vertical cryogenic CO 2 & N 2 O Tanks
Vacuum Insulated vertical cryogenic CO 2 & N 2 O Tanks CRYOLOR introduces the latest generation vacuum isolated cryogenic tank, the RCIA Céline 3, for liquid CO 2 and N 2O service, with inner vessel in
More informationTOPLINE ELECTRONICS LTD CO2 CONTROL UNIT MANUAL
TOPLINE ELECTRONICS LTD CO2 CONTROL UNIT MANUAL CO2 MANUAL Page 1 of 10 General This control equipment has been designed to add CO2 (carbon dioxide) to a swimming pool to control the ph level downwards.
More informationINSTRUCTIONS FOR MODELS APC & APG HIGH PURITY, CORROSIVE GAS REGULATORS
INSTRUCTIONS FOR MODELS APC & APG HIGH PURITY, CORROSIVE GAS REGULATORS THIS BOOKLET CONTAINS PROPRIETARY INFORMATION OF ADVANCED SPECIALTY GAS EQUIPMENT CORP. AND IS PROVIDED TO THE PURCHASER SOLELY FOR
More informationPROCESS GAS SAMPLING SYSTEMS
1 PROCESS GAS SAMPLING SYSTEMS Engineered Solutions 2 Sample conditioning system System functions How it works Key components Design and layout Pre-conditioning components Custom solutions System functions
More informationI. Subject: Medical Gas Systems Utility Failure Interim Procedure III. Purpose:
I. Subject: Medical Gas Systems Utility Failure Interim Procedure II. Purpose: To provide a systematic response to medical gas system failure and restoration of this critical utility. III. Procedure: Systems
More informationHANDBOOK SAFETY DEVICES. Ed SAFETY DEVICES DS-ED 01/ ENG 1
HANDBOOK Ed. 2017 DS-ED 01/2017 - ENG 1 CHAPTER 9 BURSTING DISC DEVICES IN SERIES 3070 SCOPE Use: protection against possible overpressure of the apparatuses listed below, with regard to the operating
More informationR-410A 50% R-32 50% R-125.
R-410A R-410A Facts Ozone friendly- No Chlorine Replacement for R-22, NOT a drop in! Higher Pressure Range-50 to 75% higher than R-22 Requires Special Lubricants R-410A It s a Blended Refrigerant. 50%
More informationOperating Manual. Model 25200B/25202B Refrigerant Recovery Unit. (Not for use in automotive R-134a applications)
Operating Manual Model 25200B/25202B Refrigerant Recovery Unit (Not for use in automotive R-134a applications) ROBINAIR Refrigerant Recovery Unit Model: 25200B /25202B Series Type of Equipment: Recovery
More informationNew AQF Filter Polymer Filtration System
New AQF Filter Polymer Filtration System Operator Manual Covering Serial Number 20002001 onwards February 2011 Index Disclaimer notice...3 Introduction...4 Important safety notices...5 Getting started...6
More informationCORROSION AT THE AIR-WATER INTERFACE REMOVE THE GAS
CORROSION AT THE AIR-WATER INTERFACE There are three (3) physical attributes of oxygen that explain why almost all corrosion in wet pipe fire sprinkler systems occurs in close proximity to trapped air
More informationDECLARATION OF INCORPORATION
AESSEAL (MCK) Ltd. Systems Division 139a Hillsborough Old Road Lisburn Northern Ireland BT27 5QE Tel +44 (0) 2892 669966 Fax +44 (0) 2892 669977 When selecting and installing suitable Barrier Fluid System
More informationMicroBulk Solutions. Next Generation Solutions for Safe and Efficient Delivery for Gas and Liquid Applications
MicroBulk Solutions Next Generation Solutions for Safe and Efficient Delivery for Gas and Liquid Applications MicroBulk System Engineered to improve the filling process: Safely Efficiently High Quality
More informationEDUCATION DEPARTMENT ACCU-TEST
ABN 17 100 208 964 EDUCATION DEPARTMENT ACCU-TEST GAS SAFETY SHUT OFF SYSTEM Operating & Installation Manual Head Office (Melbourne) Sydney Brisbane (Distributor) 1/5 Samantha Court 2/14 Welder Road 17
More informationRelief Systems. 11/6/ Fall
Relief Systems 1 Relief Scenarios o A single relief event requires a particulate vent area and valve size o Relief scenarios are determined based on a PHA o For each scenario, a vent area is calculated
More informationQwik System Flush Air Conditioning & Refrigeration System Flush
Qwik System Flush Air Conditioning & Refrigeration System Flush TM System Flush FORMULATED FOR FIGHTER JETS MODIFIED FOR HVAC SYSTEMS The original Qwik System Flush was developed by Mainstream Engineering
More informationSUBSTATION MAINTENANCE ELECTRICAL OPERATING PROCEDURE
Page 1 of 6 A. PURPOSE AND SCOPE This procedure establishes safe working practices for handling sulfur hexafluoride (SF 6 ) gas and release minimization practices. This document also specifies methods
More informationDesign & Operating Guidelines for Liqui-Cel Extra-Flow Membrane Contactors
Design & Operating Guidelines for Liqui-Cel Extra-Flow Membrane Contactors For the following products: 2.5 x 8, 4 x 13, 4 x 28, 6 x 28, 8 x 20, 8 x 40, 8 x 80, 10 x 28, 14 x 28 and 14 x 40 TABLE OF CONTENTS
More informationJORDAIR/BAUER Service Manual
JORDAIR/BAUER Service Manual Breathing Air Compressor Maintenance Log Doc. ServiceManual Page - 1 SAFETY RELEASE-2016 The following document is prepared to ensure safety of operators and service technicians.
More informationInstallation and operating manual. Pneumatic control station LK product no: PCS 1-10
LK product no: PCS 1-10 Article no: 74503 Revision:8 Article no: 74503 Revision: 8 2 (23) Contents 1. General information... 5 2. Safety precautions... 5 2.1 Significance of symbols... 5 2.2 Explanatory
More informationPiped Air SCBA Refilling System Standard
WALT WHITE Fire Chief 5770 Freeport Blvd., Suite 200 Sacramento, CA 95822-3516 Ph: (916) 808-1300 Fax: (916) 808-1629 www.sacfire.org Piped Air SCBA Refilling System Standard SCOPE: This specification
More informationOPERATION MANUAL RTI RHS650 RTI TECHNOLOGIES, INC East Market Street York, PA Manual P/N
OPERATION MANUAL RTI RHS650 RTI TECHNOLOGIES, INC. 4075 East Market Street York, PA 17402 Manual P/N 035-80589-02 Table of Contents Components... 2 Test... 4 Recovery/Recycling... 5 Evacuation... 7 Charging...
More information200 PSI HIGH-FLOW AIR SOURCE KIT
200 PSI HIGH-FLOW AIR SOURCE KIT 50% Duty Compressor on 2.0 Gallon Air Tank PART NO. 20008 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of
More information200 PSI FAST-FILL AIR SOURCE KIT
200 PSI FAST-FILL AIR SOURCE KIT 55% Duty Compressor on 2.0 Gallon Air Tank PART NO. 20007 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of
More informationInstallation and User Manual
49124589 Revision A August 2015 PacE Flow Controller Installation and User Manual Save These Instructions Table of contents Table of contents..................................................... 2 INSTALLATION............................................................3
More informationHYPOXIC AIR FIRE PREVENTION SYSTEM TECHNICAL SPECIFICATION
HYPOXIC AIR FIRE PREVENTION SYSTEM TECHNICAL SPECIFICATION Introduction: Hypoxic Air Fire Prevention System is a revolutionary fire prevention technology. It has the unique ability to create a breathable
More informationInstallation, Operation and Maintenance Instructions for Mild Steel Buffer Vessel
OM006 Installation, Operation and Maintenance Instructions for Mild Steel Buffer Vessel The operating and maintenance instructions contained within this package are for standard mild steel buffer vessels
More informationRefrigerant Recovery System Model 3600 Part No
Refrigerant Recovery System Model 3600 Part No. 2000-3600 Operation & Maintenance Manual Instruction 2079-0140 Rev 2 - December 2012 WARNING: Inhalation of high concentrations of refrigerant vapors is
More informationTESCOM 50-4X Series Safety, Installation & Start-Up Procedures
Operations & Service Manual TESCOM 50-4X Series Safety, Installation & Start-Up Procedures Do not attempt to select, install, use or maintain this product until you have read and fully understood this
More informationInstallation Operating Instructions for Duplex Manual Manifolds PX-TMD Series
Introduction Powerex manifolds are cleaned, tested and prepared for the indicated gas service and are built in accordance with the Compressed Gas Association guidelines. The manifold consists of a regulator
More informationAlkylphosphines. Storage and Handling Recommendations
Alkylphosphines Storage and Handling Recommendations 2 The Phosphine Specialties Group has been producing phosphine and phosphine derivatives on a large scale for a number of years and the handling procedures
More informationPRESSURE SYSTEMS POLICY
PRESSURE SYSTEMS POLICY PRESSURE SYSTEMS POLICY 1. Introduction 2. Policy Statement 3. Scope 4. Background 5. Roles & Responsibilities 6. Training 7. Contractors 8. Policy Review 1. Introduction The Kilmarnock
More informationR E D I C O N T R O L S
R E D I C O N T R O L S Operation & Maintenance Manual Portable Service Purger for Low Pressure Chillers Model: PSP-LP-1B For Refrigerants R-11, R-113, R-114 & R-123 & Other Similar Refrigerants File Literature
More informationPREVENTION OF EXCESSIVE PRESSURE DURING FILLING OF CRYOGENIC VESSELS
PREVENTION OF EXCESSIVE PRESSURE DURING FILLING OF CRYOGENIC VESSELS AIGA 054/08 GLOBALLY HARMONISED DOCUMENT Asia Industrial Gases Association 3 HarbourFront Place, #09-04 HarbourFront Tower 2, Singapore
More informationCopeland Discus with CoreSense Diagnostics January 2011
Copeland Discus with CoreSense Diagnostics January 2011 Slide 1 1/27/2011 5:48 PM Discus with CoreSense Diagnostics Case Studies Supermarket In Columbus, Ohio Saves $4,500 With Discus with CoreSense Diagnostics
More informationCompact Triple Cabinet Outlet Station Model Installation and Operating Instructions
Compact Triple Cabinet Outlet Station Model 6258-1 Installation and Operating Instructions The Porter Compact Triple Outlet Station (6258-1) provides a quick, safe, and reliable method of connection to
More informationInstallation Operating Instructions for Simple Duplex Manual Manifolds PX-TSD Series
Introduction Powerex manifolds are cleaned, tested and prepared for the indicated gas service and are built in accordance with the Compressed Gas Association guidelines. The manifold consists of a regulator
More informationI/P Transducer Positioner Module
I/P Transducer Positioner Module VRC P/N: 7958032 Installation, Operation and Maintenance Instructions 2.09 [53.1] 1.30 [32.9] 2.97 [75.5] 0.78 [19.8] 0.18 [4.4] 1.42 [36.1] n.18 MOUNTING HOLES (2) PLACES
More informationSDS -Series 4C-D201/-D202 Supplemental Drying System User s Manual
SDS -Series 4C-D201/-D202 Supplemental Drying System User s Manual 8 Executive Drive P.O. Box 2105 Toms River, NJ 08754 (732) 244-0010 (800) 337-3762 fax (732) 244-8140 www.permapure.com info@permapure.com
More informationMEGR-1912 Instruction Manual
MEGR-1912 PRESSURE REGULATOR Instruction Manual- Look Inside For: Description Installation Start-Up Maintenance Parts Ordering Parts List Marshall Excelsior Company Marshall, MI 49068 269-789-6700 FAX
More informationV46 Series 2-Way Pressure-Actuated Water-Regulating Valves With Union Fittings
Installation Instructions V46 Issue Date 11//1 V46 Series -Way Pressure-Actuated Water-Regulating Valves With Union Fittings Application IMPORTANT: The V46 Series -Way Pressure-Actuated Water-Regulating
More informationMitigation Starts With Design! Continues with Safe Operation, Mechanical Integrity and Training!
P.S.I.G. Mitigation Starts With Design! Continues with Safe Operation, Mechanical Integrity and Training! Last Unfortunately is When It Goes Wrong! The Failure! The Release! Loss of Product or Production
More informationMETHODS TO PREVENT THE PREMATURE ACTIVATION OF RELIEF DEVICES ON TRANSPORT TANKS
METHODS TO PREVENT THE PREMATURE ACTIVATION OF RELIEF DEVICES ON TRANSPORT TANKS IGC Doc 184/14/E EUROPEAN INDUSTRIAL GASES ASSOCIATION AISBL AVENUE DES ARTS 3-5 B 1210 BRUSSELS Tel: +32 2 217 70 98 Fax:
More informationCorrosion Protection in Dry-Pipe Systems Article and photos by Gregory Havel, except where noted. May 21, 2018
Corrosion Protection in Dry-Pipe Systems Article and photos by Gregory Havel, except where noted May 21, 2018 Corrosion in automatic fire sprinkler systems is a concern to those who design, install, and
More informationMedical Oxygen Concentrator Systems. Generate gases on site generate savings
Medical Oxygen Concentrator Systems Medical Oxygen is a critically important commodity to all Health Care Facilities (HCF s) How is Oxygen Supplied? Depending on the size and needs of the HCF, Oxygen can
More informationAIR CONDITIONERS. Features. Manufactured for Fujitsu General America, Inc. Fairfield, NJ. FORM NO. AFJ-220 Supersedes Form No.
FORM NO. AFJ-220 Supersedes Form No. PTZ-789 AIR CONDITIONERS FO*14C SERIES Efficiencies up to 16 S/13 Nominal Sizes 1 1 /2 to 5 Ton [5.28 to 17.6 kw] Cooling Capacities 17.3 to 60.5 kbtu [5.7 to 17.7
More informationBest Practice Guide, Servomex 2700
For full installations details refer to the. Best Practice Guide, Servomex 2700 Mounting: General Guidelines: Servomex 2700 Control Units and air supplies (utilities units) should, ideally, be mounted
More informationAPPS-160 Gen 2 User Manual
APPS-160 Gen 2 User Manual Applicable Products: PN 11914406 - APPS-160 10 to 50 PSIG operating pressure PN 11918618 - APPS-160 40 to 85 PSIG operating pressure Rev 9/16/2004 Chart Ind. www-chart-ind.com
More informationGas Check. Short testing time, with automatic start-up if no leakage was detected from previous operation.
Quality Products at Competitive Prices Gas Check Automatic testing of the down-stream installation to check that all valves are closed and that pipework and fittings are gas tight before each system start-up.
More informationNITROGEN PURGING SYSTEMS FOR THE HVAC INDUSTRY VISION INNOVATION SOLUTION
NITROGEN PURGING SYSTEMS FOR THE HVAC INDUSTRY The Purge-N2-Test is a nitrogen regulator/cylinder system, utilizing a lightweight aluminum cylinder and a state of the art regulator with an integrated cylinder
More informationCEPA Initiative: Response Time Guideline 2015 EMERGENCY SECURITY MANAGEMENT WORK GROUP
CEPA Initiative: Response Time Guideline 2015 EMERGENCY SECURITY MANAGEMENT WORK GROUP Response Time Guideline aboutpipelines.com 1 of 8 Contents Table of Contents 1.0 Background 3 Purpose 3 Scope 3 Definitions
More informationTri-Tech Medical Inc.
Introduction Tri-Tech Medical manifolds are cleaned, tested and prepared for the indicated gas service and are built in accordance with the Compressed Gas Association guidelines. The manifold consists
More informationControl units. Installation and operating instructions Series: DP-Control
Control units Installation and operating instructions Series: DP-Control Table of Contents 1 Manual introduction 1.1 Preface... 4 1.2 Icons and symbols... 4 2 Identification, service and technical support
More informationMASS FLOW SYSTEMS MASS FLOW MEASURING, CONTROLLING AND BLENDING SYSTEMS
MASS FLOW SYSTEMS MASS FLOW MEASURING, CONTROLLING AND BLENDING SYSTEMS Using state-of-the-art measuring and microprocessor technologies, Advanced has assembled a series of systems which can measure mass
More informationM-06 Nitrogen Generator (Nitrogen Making Machine)
Guideline No.M-06 (201510) M-06 Nitrogen Generator (Nitrogen Making Machine) Issued date: 20 th October, 2015 China Classification Society Foreword This Guideline is a part of CCS Rules, which contains
More informationVortex Dual. Refrigerant Recovery Machine. English Español Français Deutsch Italiano Nederlands Svenska 中文
O P E R A T I N G M A N U A L Vortex Dual Refrigerant Recovery Machine Español Français Deutsch Italiano Nederlands Svenska 中文 Table Of Contents Vortex Dual Operating Manual........................ 3 Español
More informationSERIES 10. Pilot Operated Tank Blanketing Valve, 2" PROTECTOSEAL.
SERIES 10 PROTECTOSEAL 2" NPT inlet and outlet standard Pilot operated design provides tight operating band Optional inlet and outlet connections available Inlet gas pressures from 40 PSIG to 130 PSIG
More informationGENERAL SAFETY INSTRUCTION GSI-M-2 STANDARD PRESSURE EQUIPMENT
GENERAL SAFETY INSTRUCTION GSI-M-2 STANDARD PRESSURE EQUIPMENT Publication date: 09-06-2015 All CERN Safety Rules are available on the web site: https://www.cern.ch/safety-rules Page 1 of 8 1 INTRODUCTION
More informationAE50S Automatic Air and Gas Vent for Liquid Systems Installation and Maintenance Instructions
0176050/3 IM-P017-11 ST Issue 3 AE50S Automatic Air and Gas Vent for Liquid Systems Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4
More informationfrom Thames Cryogenics Ltd Total Cryogenic Solutions Cryogenic Cluster Day 22/09/2010
from Thames Cryogenics Ltd Total Cryogenic Solutions Cryogenic Cluster Day 22/09/2010 Dewar vessel noun. A container with an evacuated space between two walls, capable of maintaining its contents at a
More informationAdditel 780 Series Pressure Controller
Additel 780 Series Pressure Controller Pressure ranges from vacuum to 3,000 psi (200 bar) Removable interchangeable intelligent sensors Precision accuracy of 0.005% of reading plus 0.005% of full scale
More informationStormy Phillips BASICS OF LEASE AUTOMATIC CUSTODY TRANSFER (LACT) SYSTEMS
Stormy Phillips BASICS OF LEASE AUTOMATIC CUSTODY TRANSFER (LACT) SYSTEMS Why is Stormy Walking Funny?? What is a LACT system? Introduction A LACT unit is a group of equipment designed specifically for
More informationModel 3600-R410A. Part No Instruction Operation & Maintenance
Model 3600-R410A Part No. 2000-3600 Instruction 2079-0140 Operation & Maintenance Rev. G September 2007 WARNING: INHALATION OF HIGH CONCENTRATIONS OF REFRIGERANT VAPORS IS HARMFUL AND MAY CAUSE HEART IRREGULARITIES,
More information