INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL TB305-1MM
|
|
- Patricia Griffith
- 6 years ago
- Views:
Transcription
1 HYDROLOGICAL SEVICES PTY LTD INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL TB305-1MM QUALITY SYSTEM ISO CERTIFIED HYDROLOGICAL SERVICES PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone:(Int.) Fax: :(Int.) Phone:(Nat.) (02) Fax: :(Nat.) (02) Web: Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
2 Table of Contents I. GENERAL... 3 II. UNPACKING YOUR TB3 RAINGAUGE... 3 III. SPECIFICATION... 4 IV. INSTALLATION... 5 V. TEST OPERATION... 6 VI. MAINTENANCE... 7 VII. ELECTRICAL... 9 VIII. CALIBRATION... 9 IX. TB305-1MM PART LIST TB305-1MM Base Part List TB305-1MM Bucket Part List Syphon Part List Filter Part List Enclosure Part List XI. FIELD CALIBRATION DEVICE Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
3 I. GENERAL TIPPING BUCKET RAINGAUGE MODEL TB305-1MM The Hydrological Services Tipping Bucket Raingauge (TB305-1MM) is recognised as the standard for measuring rainfall and precipitation in remote and unattended locations. The TB305-1MM raingauge operates on the tipping bucket principle, and has a metal bucket. A receiver of 305mm diameter collects the rainfall, which is strained by a catch filter and a straight through discharge mechanism before being passed to the tipping bucket measuring system. Tips of the bucket occur with each 1 mm precipitation collected. A reed switch detects these events and produces a momentary contact closure signal for: Logging in our Rainfall Data Logger Transmission by GSM, 3G, Satellite or PSTN (RainTrak System) Display on our Rainfall Counter (TRD). II. UNPACKING YOUR TB3 RAINGAUGE This package should contain: TB305-1MM Raingauge TB311/5 5 metre connecting lead Please verify you have received these items and that the Tipping Bucket Raingauge resolution is as ordered. To prepare the Tipping Bucket Raingauge for installation: lift the unit from the carton and place on secure surface remove polythene bag loosen the three enclosure securing screws and back them off until screw head is clear of the enclosure. lift the enclosure from the gauge carefully remove the elastic band/support pad from the bucket. Your Tipping Bucket Raingauge is now ready for installation. Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
4 III. Receiver: Sensitivity: SPECIFICATION 305 mm diameter heavy duty cast aluminium, Powder coated. one tip at 1.0mm of rainfall. Maximum Intensity: Calibration accuracy: 700 mm / hr. TB3 bucket capacity Range Accuracy 1.0 mm mm/hr + 2 % mm/hr + 3 % Long term stable calibration. Humidity: 0 to 100 % Temperature: Contact system: - 20 to +70 o C dual reed switches potted in soft silicon rubber with varister protection. - Max Capacity: 24 Volts (0.5 amp max.) - Resistance: Initial contact resistance 0.1 OHMS - M.T.B.F: 10 8 to 10 9 Operations Funnel Discharge Orifice: Bucket: Base: Level: Mounting holes: Pivots: Insect covers: Outer enclosure: Height: Weight: Straight through discharge mechanism. Bucket assembly balanced to gms. Aluminium. bulls eye level adhered to aluminium base. three 10 x 20 mm slotted holes with 234 to 254 PCD cast in feet attached to outside diameter of base. ground nickel silver pivots with hard stainless steel shaft. stainless steel mesh on all openings to prevent insects and ants entering gauge. keyed to enable the release of the outer enclosure without the need for the removal of the three securing screws. 415 mm 5.5 kg Packed Dimensions: 6 kg 0.04m 3 Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
5 IV. INSTALLATION DIAGRAM 1 i. Site Selection Rainfall measurements are intended to be representative of the actual rain falling on a given area. Some of the more important factors which influence the representativeness of a gauge are as follows: Site the gauge on level ground where possible. Avoid sloping sites. Site should have adequate protection from strong winds. Site should be free of large obstructions such as buildings and trees. Provide suitable ground surface to avoid splashing into the gauge. Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
6 ii. Setting up Install the gauge on the foundation. A suggested foundation is shows in Diagram 1. Loosen the three enclosure securing screws and the enclosure. The gauge is provided with a level. Proceed to level by adjusting the hold down anchors as required. Connect lead to the rain gauge terminals, in accordance with Diagram 3, and to the recording device, in accordance with manufacturer s instruction manual. V. TEST OPERATION Manually tip the bucket a number of times, ensuring that each tip is being recorded and that the tilting mechanism is operating freely. Replace and secure the enclosure. Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
7 VI. MAINTENANCE The only routine maintenance required is cleaning. The following items should be checked regularly for cleanliness: Catch filter Discharge Mechanism Straight Through (refer diagram 2) Interior of bucket Top surface of adjusting screws Ensure Rain Gauge is level using the bubble level fitted to the base Enclosure locking screws - lightly lubricate after cleaning All insect screens i. Dismantle Details To dismantle the Filter & Straight through discharge mechanism assembly. Push filter and pull Straight through discharge mechanism at the same time. Do not twist. Push Filter Do not twist while pushing & pulling Pull Straight through discharge mechanism Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
8 1- Filter Cover Part No. TB Filter Screen Part No. TB O Ring Part No. SC Discharge Mechanism Part No. TB DIAGRAM 2 ii. Assembly Details To re-assemble push the filter/straight through discharge mechanism assembly back in place. Do not twist Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
9 VII. ELECTRICAL Dual reed switches are provided for several reasons: Two isolated switches permit the control of two separate circuits; e.g. a local counter and a telemetry circuit. Parallel connection of both switches increases the current carrying capacity of the contact system if required. Parallel switch operation confers a degree of redundancy in locations where data from the raingauge is critical to flood warning etc. Mounting Holes Switch 1 Switch 2 Voltage free closure reed switch VIII. CALIBRATION All gauges have been calibrated by Hydrological Services Pty Limited prior to despatch. The following products and services are available from Hydrological Services Pty Ltd: Field Calibration Device, Model FCD-730, for routine field check calibrations, supplied with operating instruction sheet. Laboratory Calibration Unit, Model TB340, for calibration after servicing in workshops, supplied with operating manual. Recalibration Service at Hydrological Services factory. Please contact either Hydrological Services Pty Ltd or our local distributor for further information. Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
10 IX. TB305-1MM PART LIST Metal Note: The TB305-1MM Raingauge can be ordered with a synthetic ceramic coated brass bucket only. Raingauge Part No. TB305-1MM Raingauge Description Tipping Bucket Raingauge, bucket capacity 1.0mm, bucket type synthetic ceramic coated brass Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
11 TB305-1MM Base Part List Item2. Part no.: TB303 Descript: Reed Switch Assembly Item3. Part no.: (See next page) Descript: Bucket Assembly Item11. Part no.: SC Descript: Reed Switch Screw Quantity: 2 Item4. Part no.: TB312 Descript: Adjusting Screw Quantity: 2 Item10. Part no.: TB Descript: Insect Screen Quantity: 2 Item5. Part no.: SC Descript: Locknut Quantity: 2 Item9. Part no.: SC Descript: Bullseye Level Item6. Part no.: HS Descript: Pivot Screw Quantity: 2 Item1.TB30001 Descript: Base Item7. Part no.: SC Descript: Pivot Nut Quantity: 2 Item8. Part no.: SC Descript: Enclosure Screw Quantity: 3 Item12. Part no.: SC Descript: Screw Quantity: 3 Item13. Part no.: SC Descript: Nut Quantity: 3 Item14. Part no.: SC Descript: Pivot Nut Quantity: 3 Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
12 TB305-1MM Bucket Part List Item15: Part no: HS304 Descript: Bucket Metal Bucket Item16: Part no: HS Descript: Bucket Axle Quantity: 2 Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
13 Syphon Part List Item18: Part no.: SC Descript: O Ring Item17: Part no.: TB Descript: Straight through discharge mechanism Straight through discharge mechanism assembly Part no.: TB409 Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
14 Filter Part List Item19: Part no.: TB Descript: Filter Screen Item20: Part no.: TB Descript: Filter Cover Filter Assembly TB410 Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
15 Enclosure Part List Outer Funnel Inner Funnel Screw Item21: Part no.: TB336 Descript: Enclosure Assembly Vent Enclosure Part no. Description Quantity TB Funnel Extension 1 TB Funnel 1 TB Enclosure 1 TB Vent 1 SC Screw 3 TB336 breakdown assembly Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
16 HYDROLOGICAL SEVICES PTY LTD XI. FIELD CALIBRATION DEVICE Tipping Bucket Raingauge TB305-1MM Issue 2:13/01/2014
HYQUEST SOLUTIONS PTY LTD INSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE MODEL TB6
INSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE MODEL TB6 QUALITY SYSTEM ISO:9001 CERTIFIED HYQUEST SOLUTIONS PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone:(Int.) 612 9601 2022 Fax: :(Int.)
More informationINSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE. MODEL TB3/0.1mm
INSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE MODEL TB3/0.1mm QUALITY SYSTEM ISO 9001 2008 CERTIFIED HYQUEST SOLUTIONS PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone:(Int.) 612 9601 2022 Fax:
More informationINSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL TB3
INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL TB3 QUALITY SYSTEM ISO:9001 CERTIFIED HYQUEST SOLUTIONS PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone:(Int.) 612 9601 2022 Fax: :(Int.) 612
More informationINSTRUCTION MANUAL TIPPING BUCKET RAINGUAGE MODEL TB3
HYDROLOGICAL SEVICES INSTRUCTION MANUAL TIPPING BUCKET RAINGUAGE MODEL TB3 QUALITY SYSTEM ISO 9001 2000 CERTIFIED HYDROLOGICAL SERVICES PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone:(Int.)
More informationHYQUEST SOLUTIONS PTY LTD INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL TB6
INSTRUTION MANUAL TIPPING BUKET RAINGAUGE MODEL TB6 QUALITY SYSTEM ISO:9001 ERTIFIED HYQUEST SOLUTIONS PTY LTD PO BOX 332, LIVERPOOL B. NSW 1871, AUSTRALIA Phone:(Int.) 612 9601 2022 Fax: :(Int.) 612 9602
More informationHYQUEST SOLUTIONS PTY LTD INSTRUCTION MANUAL TIPPING BUCKET RAIN GAUGE MODEL TB4
INSTRUTION MANUAL TIPPING BUKET RAIN GAUGE MODEL TB4 QUALITY SYSTEM ISO:9001 ERTIFIED HYQUEST SOLUTIONS PTY LTD PO BOX 332, LIVERPOOL B. NSW 1871, AUSTRALIA Phone:(Int.) 612 9601 2022 Fax: :(Int.) 612
More informationHYDROLOGICAL SERVICES INSTRUCTION MANUAL TIPPING BUCKET RAINGAUGE MODEL TB4
HYDROLOGIAL SERVIES INSTRUTION MANUAL TIPPING BUKET RAINGAUGE MODEL TB4 QUALITY SYSTEM ISO 9001 2008 ERTIFIED HYDROLOGIAL SERVIES PTY LTD PO BOX 332, LIVERPOOL B. NSW 1871, AUSTRALIA Phone:(Int.) 612 9601
More informationPO Box 370 Phone: Swansea NSW 2281 Fax: AUSTRALIA Mobile: Web:
EZI-DRY Pty Limited ABN: 98 114 507 443 PO Box 370 Phone: 0249711993 Swansea NSW 2281 Fax: 0249135490 AUSTRALIA Mobile: 0427587900 Web: www.ezi-dry.com.au Email: ezidry@exemail.com.au INSTRUCTION MANUAL
More informationHyquest Solutions Pty Ltd
INSTRUCTION MANUAL BUBBLERS MODELS HS23SL / HS23DL / HS23DO QUALITY SYSTEM ISO: 9001 CERTIFIED HYQUEST SOLUTIONS PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone:(Int.) 612 9601 2022 Fax: :(Int.)
More informationOEM Manual MODEL 2305 ECONOMICAL DIGITAL SINGLE CYLINDER SCALE
OEM Manual MODEL 2305 ECONOMICAL DIGITAL SINGLE CYLINDER SCALE 1 These instructions generally describe the installation, operation, and maintenance of subject equipment. The manufacturer reserves the right
More informationNOVALYNX CORPORATION MODEL RAIN GAUGE CALIBRATOR INSTRUCTION MANUAL
NOVALYNX CORPORATION MODEL 260-2595 RAIN GAUGE CALIBRATOR INSTRUCTION MANUAL REVISION DATE: August 2018 Receiving and Unpacking Carefully unpack all components and compare to the packing list. Notify NovaLynx
More informationOEM Manual. MODEL ½ Digit DRUM SCALE
OEM Manual MODEL 4020-3 ½ Digit DRUM SCALE Scaletron Industries, Ltd. Bedminster Industrial Park 53 Apple Tree Lane P.O. Box 365 Plumsteadville, PA 18949 USA Toll Free: 1-800-257-5911 (USA & Canada) Phone:
More informationHydrological Services Pty Ltd 2012
INSTRUCTION MANUAL DRY BUBBLE UNIT MODEL HS23SL/HS23DO HYDROLOGICAL SERVICES PTY LTD PO BOX 332, LIVERPOOL B.C NSW 1871, AUSTRALIA Phone: (Int.) 612 9601 2022 Fax:(Int.) 612 9602 6971 Phone: (Nat.) (02)
More information97C COMPRESSOR KIT 12V PART NO C COMPRESSOR KIT 24V PART NO C COMPRESSOR KIT PART NO
97C COMPRESSOR KIT 12V PART NO. 00097 97C COMPRESSOR KIT 24V PART NO. 02497 98C COMPRESSOR KIT PART NO. 00098 97C 98C IMPORTANT: It is essential that you and any other operator of this product read and
More informationDiscontinued. Powers Controls. Technical Instructions Document No P25 RV Rev. 1, May, RV 201 Pressure Reducing Valves.
Powers Controls RV 201 Pressure Reducing Valves Description Features Product Numbers Dual Pressure PRV Technical Instructions Document No. 155-049P25 RV 201-1 Single Pressure PRV The RV 201 Pressure Reducing
More informationTHE MF-400 SERIES. Operating and Service Manual. Series includes all variants of MF-400/401
THE MF-400 SERIES Operating and Service Manual Series includes all variants of MF-400/401 Issue A October 2013 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special
More informationO P E R ATING INSTRUCTIONS FOR MODEL SPR-45 Automatic Screen and Stencil Printer
O P E R ATING INSTRUCTIONS FOR MODEL SPR-45 Automatic Screen and Stencil Printer TABLE OF CONTENTS I. SPECIFICATIONS...3. II. SAFETY INSTRUCTIONS...4. III. INSTALLATION...5. IV. SET-UP...6. V. SYSTEM OPERATION...9.
More informationINFLATOR TDUX-IT-16 AND GAS CYLINDER E
INFLATOR TDUX-IT-16 AND GAS CYLINDER E7512-0160 Operating manual Inflator TDUX-IT-16 together with the special gas cylinder E7512-0160 is specifically designed for inflating TDUX duct seals. The inflator
More informationAERODYNAMIC RAIN GAUGE ARG100
Streamline Measurement Ltd ARG100 Users Manual AERODYNAMIC RAIN GAUGE ARG100 Streamline Measurement Ltd, 01457-864334, sales@streamlinemeasurement.co.uk, www.streamlinemeasurement.co.uk ARG100 : AERODYNAMIC
More informationPRODUCT CARD WALL MOUNTED FIXED BASKETBALL CONSTRUCTION PROJECTION: FROM 1,00 TO 2,25 M
PRODUCT CARD WALL MOUNTED FIXED BASKETBALL CONSTRUCTION PROJECTION: FROM 1,00 TO 2,25 M I. List of components... 2 II. Complimentary products... 2 III. Product description... 3 IV. Product Purpose... 3
More informationPRODUCT CARD WALL MOUNTED SIDE FOLDED BASKETBALL CONSTRUCTION PROJECTION: FROM 1,2 TO 2,45 M
PRODUCT CARD WALL MOUNTED SIDE FOLDED BASKETBALL CONSTRUCTION PROJECTION: FROM 1,2 TO 2,45 M I. List of components... 2 II. Complimentary products... 2 III. Product description... 3 IV. Product Purpose...
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More information444C DUAL PERFORMANCE VALUE PACK
(Chrome) PART NO. 44432 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More informationOperating Instructions Part No
DIGITAL AUTOMATIC TYRE INFLATOR Operating Instructions Part No. 11.0545 Thank you for selecting this Jamec Pem Automatic Tyre Inflator. Please read this manual before carrying out any installation or service
More informationPosition locking powerful chuck. CKL2-*-HC Series CKL2-40CS-HC CKL2-50CS-HC CKL2-63CS-HC CKL2-80CS-HC Compressed air to
RV* FH1 G G B FH Specifications Descriptions Cylinder bore size Working fluid Max. working pressure Min. working pressure Ambient temperature Port size Operational stroke length Rod diameter Capacity of
More informationHYDRAULIC MOBILE LIFTING TABLE
HYDRAULIC MOBILE LIFTING TABLE MODEL NO: HTL300 & HTL500 PART NO: 7610148 & 76210152 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC1116 INTRODUCTION Thank you for purchasing this CLARKE
More information400C & 450C DUAL PERFORMANCE VALUE PACKS
(Chrome) PART NO. 40013 (Silver) PART NO. 45012 (Chrome) PART NO. 45013 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before
More informationVACUUM REGULATORS CONTENTS
CAD drawing data catalog is available. ACCESSORIES GENERAL CATALOG AIR TREATMENT, AUXILIARY, VACUUM, AND FLUORORESIN PRODUCTS CONTENTS Small Regulators Features 759 Specifications, Order Codes, Flow Rate
More information100C Air Compressor Kit
10010 100C Air Compressor (standard mounting bracket, CE Spec) 10014 100C Air Compressor (no leader hose or check valve, CE Spec) 10016 100C Air Compressor (with Omega Bracket, CE Spec) IMPORTANT: It is
More information200 PSI COMPRESSORS - MODEL NUMBERS
200 PSI COMPRESSORS - MODEL NUMBERS 380C AIR COMPRESSOR KIT PART NO. 38033 480C AIR COMPRESSOR KIT PART NO. 48043 380C 480C IMPORTANT: It is essential that you and any other operator of this product read
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock: - Do not disassemble. Do not attempt repairs or modifications. Refer to qualified service agencies for all service and repairs.
More informationTHE HF-300 SERIES. Operating and Service Manual. Series includes all variants of HF-300/301
THE HF-300 SERIES Operating and Service Manual Series includes all variants of HF-300/301 Issue A July 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 3.1. Spring Loaded...
More information420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO
420C AIR COMPRESSOR KIT PART NO. 42042 460C AIR COMPRESSOR KIT PART NO. 46043 420C 460C IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this
More informationOperating Instructions
Operating Instructions Sensors Type 705 H 2 S Sensor and Transmitter for Electrochemical Cells Ul Certified HELPING TO MAKE A SAFER WORLD Ensure that you read and understand these operating instructions
More informationINSTRUCTION MANUAL. 840 Transmitter. Loop Powered Dissolved Oxygen Transmitter
INSTRUCTION MANUAL Loop Powered Dissolved Oxygen Transmitter Contents Contents...2 Introduction...3 Range and Display Settings...4 Installation...5 Electrical Installation...6 Calibration...7 EasyCal...8
More informationModel PSI Compressor with 3-Gallon Air Tank 12VDC
Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing
More informationGREIG FILTERS, INC. OPERATION MANUAL
GREIG FILTERS, INC. OPERATION MANUAL MODEL DCFH 3P 15/3 100 S4 DOE/222 DUAL CARTRIDGE FILTER HOUSING TABLE OF CONTENTS I. INTRODUCTION II. CARTRIDGE FILTER HOUSING UNIT A. OPERATION B. INSTALLATION C.
More informationSDI mA Pressure Transducer (Submersible + Dry) Model WL2100 Operating Manual
SDI-12 + 4-20mA Pressure Transducer (Submersible + Dry) Model WL2100 Operating Manual (Submersible) WL2100W (Dry) WL2100D QUALITY SYSTEM ISO: 9001 CERTIFIED HYQUEST SOLUTIONS PTY LTD 48-50 Scrivener St,
More informationPRO-50 Instrument Supply Regulator
Features CRN Approved The PRO-50 Regulator has been granted a Canadian Registration Number. Sour Service Capability Available in NACE configurations that comply with NACE MR0175/MR0103. Environmental limits
More informationARG 100 Raingauge. SKYE INSTRUMENTS LIMITED 21, Ddole Enterprise Park Llandrindod Wells Powys, LD1 6DF UK TEL: FAX:
ARG 100 Raingauge SKYE INSTRUMENTS LIMITED 21, Ddole Enterprise Park Llandrindod Wells Powys, LD1 6DF UK TEL: +44 1597 824811 FAX: +44 1597 824812 General Email: skyemail@skyeinstruments.com Technical
More informationPressure Dump Valve Service Kit for Series 3000 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator
More informationINSTALLATION MANUAL JAPANESE ENGLISH GERMAN FRENCH ITALIAN SPANISH. Before installation. Installation INSTALLATION MANUAL: B700
Thank you for purchasing this product. Please read this installation manual before assembling and using the product, and be sure to use the product properly. An accident or injury can result if the product
More informationModel 106 DPI "Micro-switch" Installation and Operating Instructions
Mid-West Instrument Model 106 DPI "Micro-switch" Installation and Operating Instructions BULLETIN NO. IM116DPImicro/09A Replaces --- INSPECTION Before installation carefully check the Model Number on each
More informationMet One E-BAM Particulate Monitor
STANDARD OPERATING PROCEDURES Met One E-BAM Particulate Monitor AMBIENT AIR MONITORING PROGRAM for the 130 LIBERTY STREET DECONSTRUCTION PROJECT LOWER MANHATTAN DEVELOPMENT CORPORATION 1 Liberty Plaza
More information400H HARDMOUNT AIR COMPRESSOR KIT PART NO H HARDMOUNT AIR COMPRESSOR KIT PART NO
400H HARDMOUNT AIR COMPRESSOR KIT PART NO. 40042 450H HARDMOUNT AIR COMPRESSOR KIT PART NO. 45042 400H 450H IMPORTANT: It is essential that you and any other operator of this product read and understand
More informationTECHNICAL DATA. Trimpac 244a. September 16, 2013
September 16, 2013 Trimpac 244a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-1 and B-1B is a factory-assembled trim package with an electric release module in a metal enclosure. The standard trim normally
More informationSOLO TRIPOD SERIES Operator s Manual
SOLO TRIPOD SERIES Operator s Manual #1630 Solo DV 75mm 2-Stage Alloy Tripod #1501 Solo DV 75mm 2-Stage Carbon Fibre Tripod #1505 Solo ENG 100mm 3-Stage Tripod Features and Controls 75mm Bowl (#1501 &
More informationOsborne Engineering Limited. OEJ Equalised thrust bearing internals
Osborne Engineering Limited OEJ Equalised thrust bearing internals General Description The Osborne Equalised J style thrust bearing assembly operates by generating and maintaining a substantial oil film
More informationWINSAFE CORP. OPERATING AND MAINTENANCE INSTRUCTIONS GM184 TOP ACCESS END LOCK ANCHOR WAND
WINSAFE CORP. OPERATING AND MAINTENANCE INSTRUCTIONS GM184 TOP ACCESS END LOCK ANCHOR WAND For more information on this innovative product line manufactured by Winsafe Corp., please contact: G. D. MacKay
More informationTECHNICAL DATA. Trimpac 251a. Spetember 16, 2013
Spetember 16, 2013 Trimpac 251a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-6 and B-6B is a factory assembled trim package for a double interlocked preaction system with an electric/pneu-lectric release
More informationInstallation, Operation and Maintenance Manual for Back Pressure Regulator
Installation, Operation and Maintenance Manual for Back Pressure Regulator Model 8860 2009 Groth Corporation IOM-8860 Rev. B 12541 Ref. ID: 95565 Page 2 of 13 Table of Contents I. INTRODUCTION 3 II. DESIGN
More informationHyQuest Solutions Pty. Ltd.
INSTRUCTION MANUAL L GAS PURGE COMPRESSOR MODEL HS55V / HS55VDO/HS55VB Gas Purge Compressor- Model HS-55/DO/D DB HS-55 100-1 Issue 2: 30/5/2014 CONTENTS Contents HS 55 & HS 55DO & HS 55DB GAS PURGE COMPRESSOR...
More informationWelker Sampler. Model GSS-1. Installation, Operation, and Maintenance Manual
Installation, Operation, and Maintenance Manual Welker Sampler Model GSS-1 The information in this manual has been carefully checked for accuracy and is intended to be used as a guide to operations. Correct
More informationGas density monitor With integrated transmitter Model GDM-100-TI
SF 6 gas solutions Gas density monitor With integrated transmitter Model GDM-100-TI grid Products WIKA data sheet SP 60.05 for further approvals see page 5 Applications Gas density monitoring of closed
More informationNickel-Plated Brass Right Angle Flow Control Valves NPTF/Inch Series GSCU, GMCU, GSVU, GMVU, GSCO, GMCO
Nickel-Plated Brass Right Angle Flow Control Valves NPTF/Inch Series GSCU, GMCU, GSVU, GMVU, GSCO, GMCO Swivel Design : Meter-Out, Meter-In and Needle Orifice Tube Diameter OD: 1/8, 5/2, 1/4, 5/16, /8
More information1805 Series Relief Valves
Instruction Manual Form 1211 1805 Series October 2011 1805 Series Relief Valves! WARNING Failure to follow these instructions or to properly install and maintain this equipment could result in an explosion
More information12S 1st Stage. -Maintenance Procedure-
12S 1st Stage -Maintenance Procedure- 1 Warning! All maintenance and repair procedures MUST be performed by a Mares authorized Service Center and/or Distributor. Therefore, the information provided below
More informationTECHNICAL DATA. TRIMPAC Model B-5 & B-5B
September 16, 2013 Trimpac 250a 1. DESCRIPTION DEsCRIPTIoN is a factory assembled trim package for a ed an electric/pneumatic release module in a metal enclosure. The standard trim normally required on
More informationCKL2 Series. Powerful chuck. Operational stroke length: 5, 6, 8, 10, 12, 16, 20, 23mm. Specifications. Switch specifications
RV* FH1 G B FH G A S Specifications Descriptions Size Cylinder bore size mm Working fluid Max. working pressure MPa Min. working pressure MPa Ambient temperature C Port size Operational stroke length mm
More informationNOVALYNX CORPORATION MODEL ANALOG OUTPUT EVAPORATION GAUGE INSTRUCTION MANUAL
NOVALYNX CORPORATION MODEL 255-100 ANALOG OUTPUT EVAPORATION GAUGE INSTRUCTION MANUAL REVISION DATE: JANUARY 2010 Receiving and Unpacking Carefully unpack all components and compare to the packing list.
More informationLMU100/200 Series. Standard Specifications
Mist Spray Unit MU/ Series Intermittent spray to cutting and press gear chains, etc. Standard Specifications Inlet air Oil tank set range Oil Dynamic viscosity of oil ( C) Oil tank capacity (cm ) mbient
More informationPoollift Delphin. Version: February, 2015 MANUAL AND OPERATING INSTRUCTIONS
Poollift Delphin Version: February, 2015 MANUAL AND OPERATING INSTRUCTIONS Content 1. Introduction... 3 2. Technical Specifications... 3 Used materials... 3 3. Installation Instructions... 4 Fastening
More informationaerodynamic rain gauge
aerodynamic rain gauge Contents On these operating instructions... 2 1. General description... 2 1.1 Description of the raingauge... 2 1.2 Choosing a site... 2 2. Installation of the raingauge... 3 2.1
More informationInstallation Operation Maintenance. Bermad Level Control Valve with Modulating Horizontal Float Pilot valve One Way Flow IOM.
Bermad Level Control Valve with Modulating Horizontal Float Pilot valve One Way Flow Model: FP 450-80 Installation Operation Maintenance PAGE 1 OF 5 1. Safety First BERMAD believes that the safety of personnel
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationManifolds & pressure reducing sets
Manifolds & pressure reducing sets Automatic Changeover Manifold (Electronic) Providing continuous supply of medical gases Pneumatech Medical Gas Solutions (PMGS) PureGAS Manifolds provide a duty or standby
More information4/2 way Pneumatic Solenoid Valve
4/2 way Pneumatic Solenoid Valve Compact design Push-over solenoid coil Exhaust air can be regulated Tube, threaded and sub-base connections Type combined with Seat valve version Type 2508 Type 2510/11
More informationD I G I T A L C L A M
The MAXX Press D I G I T A L C L A M OPERATOR S MANUAL 6 x0 x5 5 x5 Safety Instructions When using your heat press, basic precautions should always be followed, including the following:.. 3.. 5. 6. 7.
More informationTECHNICAL DATA ACCELERATOR MODEL E-1
Page 1 of 10 1. PRODUCT DESCRIPTION The Viking Model E-1 Accelerator is a quick-opening device. When installed with the required external Anti-flood Device, the assembly is designed to increase the operating
More informationSeries IRV1000/2000/3000
CAT.ES60-16 A Regulator Series /2000/3000 Allows adjustment of vacuum line pressure Regulator Series /2000/3000 3 sizes offered in the series Variations have been expanded to three sizes from only one
More informationBest Practice Guide, Servomex 2700
For full installations details refer to the. Best Practice Guide, Servomex 2700 Mounting: General Guidelines: Servomex 2700 Control Units and air supplies (utilities units) should, ideally, be mounted
More informationUSER MANUAL
C Cimarron Sports 1-888-816-6517 www.cimarronsports.com Combo Pitching Machine USER MANUAL TABLE OF CONTENTS Thank you for purchasing the Cimarron Combo Pitching Machine. The Cimarron Combo Pitching Machine
More informationComponents for air preparation and pressure adjustment. OUT port position ( ) connected Rear side. of IN port. Air tank. directly.
Components preparation and pressure adjustment ABP Overview ABP is a component that enables boosting by s only up to twice primary pressure (.0MPa max.) in combination with using air tank but not using
More informationType BBS-03, BBS-05, BBS-06, BBS-25
Type BBS-03, BBS-05, BBS-06, BBS-25 Sterile connection elements Sterile Verbindungselemente Raccords union stériles Operating Instructions Bedienungsanleitung Manuel d utilisation 1. THE OPERATING INSTRUCTIONS
More informationPROPORTIONING VALVE. Model 150 INSTRUCTION MANUAL. March 2017 IMS Company Stafford Road
PROPORTIONING VALVE Model 150 INSTRUCTION MANUAL March 2017 IMS Company 10373 Stafford Road Telephone: (440) 543-1615 Fax: (440) 543-1069 Email: sales@imscompany.com 1 Introduction IMS Company reserves
More informationAdvantage Lockers & Bike
Advantage Lockers & Bike Advantage Bike Racks & Lockers Inc. is the #1 supplier of Storage Lockers and Bike Racks to the Lower Mainland s residential construction industry. With 25+ years of experience
More informationInstallation and Maintenance Manual. ECO Filtration Unit with 6-way-Top-Mount-Valve. Art. Nr
Installation and Maintenance Manual ECO Filtration Unit with 6-way-Top-Mount-Valve Art. Nr. 300100 300101 300102 Important Details: - Using of this filtration unit for swimming pools and its guard band
More informationDual Safety Shutoff Valves with Proof of Closure and NEMA 4x Enclosure. DMV-D/624L Series DMV-DLE/624L Series
Dual Safety Shutoff Valves with Proof of Closure and NEMA 4x Enclosure DMV-D/624L Series DMV-DLE/624L Series Two normally closed automatic shutoff valves in one housing. Valve 2 (V2) incorporates proof
More informationTripod Series OPERATOR S MANUAL
Tripod Series OPERATOR S MANUAL #1630 - Solo 75 2-Stage Tripod (Alloy) #1501 - Solo 75 2-Stage Tripod #2001 - Solo 75 3-Stage Tripod #1505 - Solo 100 3-Stage Tripod Features and Controls 75mm Bowl or 100mm
More informationThe MAXX Press DIGITAL CAP OPERATOR S MANUAL
The MAXX Press DIGITAL CAP OPERATOR S MANUAL Safety Instructions When using your heat press, basic precautions should always be followed, including the following:.. 3. 4. 5. 6. 7. 8. 9. 0.. Read all instructions.
More informationDual Modular Safety Shutoff Valves with Two-stage operation and Proof of Closure. DMV-ZRD/612 Series DMV-ZRDLE/612 Series
Dual Modular Safety Shutoff Valves with Two-stage operation and Proof of Closure DMV-ZRD/612 Series DMV-ZRDLE/612 Series Two normally closed automatic shutoff valves in one housing. Valve 1 (V1) incorporates
More informationGM-121: Container End Lock Anchor Wand Page 1 WINSAFE CORP. GM 121 CONTAINER END LOCK ANCHOR WAND OPERATING INSTRUCTIONS AND MAINTENANCE
GM-121: Container End Lock Anchor Wand Page 1 WINSAFE CORP. GM 121 CONTAINER END LOCK ANCHOR WAND OPERATING INSTRUCTIONS AND MAINTENANCE US Patent No. 6834745 This equipment conforms to 0321 EN795:1996
More informationDepth sensor. Product reference : REV 1. USER GUIDE and INSTALLATION GUIDE. nke Sailing competition
Depth sensor Product reference : 90-60-456 REV 1 USER GUIDE and INSTALLATION GUIDE nke Sailing competition Z.I. Kerandré Rue Gutenberg 56700 HENNEBONT- FRANCE http://www.nke.fr After sale service n 33
More informationCONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER COMPRESSOR For your personal safety please read, understand and follow the information provided in
CONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER COMPRESSOR For your personal safety please read, understand and follow the information provided in this instruction manual. 1 CONTENTS 3. Safety Precautions
More informationTECHNICAL DATA. Trimpac 257a. September 16, 2013
September 16, 2013 Trimpac 257a 1. DESCrIpTION DESCRIPTION The Viking Double SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-2 and D-2B used with either a Model E or F Deluge Valve (A.1), a Viking
More informationGILMONT ACCUCAL FLOWMETERS
OPERATING MANUAL GILMONT ACCUCAL FLOWMETERS 28W092 Commercial Ave. Barrington, IL U.S.A. 60010-2392 (847) 381-4888 (847) 381-7053 (Fax) 800-962-7142 www.barnant.com e-mail: barnant@barnant.com A-1299-0766
More informationAIR/OVER HYDRAULIC JACK 20 TON
AIR/OVER HYDRAULIC JACK 0 TON 4487 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 999 by Harbor Freight Tools.
More informationAlphasense 4-20 ma transmitters offer convenience and easy maintenance for toxic sensors:
ALPHASENSE USER MANUAL Page 1 4-20mA Transmitter for Toxic Sensors UMTOX-1 Issue 4 1 INTRODUCTION The Transmitter PCB includes circuitry for a three electrode toxic sensor to convert the µa output signal
More informationRegulator. Modular Type AR10 AR20 AR25 AR30 AR40 AR40-06 AR50 AR60. Pages 36 through 40 AR20K AR25K AR30K AR40K AR40K-06 AR50K AR60K
Modular Type Regulator Series R Regulator Series R Model R M5 x.8 ccessory R2 /8, /4 R /4, 3/8 R3 /4, 3/8 R4 /4, 3/8, /2 Pages 36 through 4 Regulator with back flow mechanism Series RK R4-6 R5 R6 R2K RK,
More informationRegulator. Modular Type AR10 AR20 AR25 AR30 AR40 AR40-06 AR50 AR60. Pages 36 through 40 AR20K AR25K AR30K AR40K AR40K-06 AR50K AR60K
Modular Type Regulator Series R Regulator Series R Model R M5 x.8 ccessory R2 /8, /4 R /4, 3/8 R3 /4, 3/8 R4 /4, 3/8, /2 Pages 36 through 4 Regulator with back flow mechanism Series RK R4-6 R5 R6 R2K RK
More informationV43 Pressure Actuated Water Regulating Valve
FANs 125, 121 Product/Technical Bulletin V43 Issue Date 0996 V43 Pressure Actuated Water Regulating Valve The V43 Pressure Actuated Water Regulating Valves are designed to regulate water flow for water-cooled
More informationGM-120: Container Top Lock Anchor Wand Page 1 WINSAFE CORP. GM 120 CONTAINER TOP LOCK ANCHOR WAND OPERATING INSTRUCTIONS AND MAINTENANCE
GM-120: Container Top Lock Anchor Wand Page 1 WINSAFE CORP. GM 120 CONTAINER TOP LOCK ANCHOR WAND OPERATING INSTRUCTIONS AND MAINTENANCE US Patent No. 6834745 This equipment conforms to 0321 EN795:1996
More informationWorkshop Compressors CLASSIC Series
www.kaeser.com Workshop Compressors CLASSIC Series Displacement: 210 to 40 l/min Pressure: 10 bar What do you expect from your Classic workshop compressor? Quality results can be achieved only by using
More informationPURA. Pure Gas Dewpoint Transmitter. Users Guide
PURA Pure Gas Dewpoint Transmitter Users Guide Issue January 2003 Page 2 Table of Contents SECTION PAGE 1 Product Overview 3 2 Preparation 3 3 Installation 3 3.1 PURA Premium & OEM Dewpoint Transmitter
More informationTECHNICAL DATA. Trimpac 256a. October 31, 2013
October 31, 2013 Trimpac 256a 1. DESCRIPTION The Viking SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-1 and D- 1B used with either a Model E or F Deluge Valve (A.1), a Viking Easy Riser check valve
More informationMaximum 0.85 MPa pressure setting Long-life, high flow perfect for balancer applications
Outstanding performance in extremely low pressure and low pressure ranges from 0.003 to. Realizing high performance, energy saving, and compact size. Realize precise pressure control in a pressure range
More informationMODEL ANALOG ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.2 TO 100FT OPERATING RANGE ANALOG OUTPUT
MODEL 862-000-200 ANALOG ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.2 TO 100FT OPERATING RANGE ANALOG OUTPUT DOCUMENT NO. 430-007H September 20, 2005 S/N IMAGENEX TECHNOLOGY CORP. 209-1875 BROADWAY
More informationKTM OM-2 SPLIT BODY FLOATING BALL VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS
Before installation these instructions must be fully read and understood SECTION 1 - STORAGE 1.1 Preparation and preservation for storage All valves should be properly packed in order to protect the parts
More informationCLEAN AGENT FIRE EXTINGUISHING SYSTEM MX 1230 Extinguishing Agent Cylinders
The technical data described herein is for components of the Minimax Fire Products MX 30 Clean Agent System. For design, installation, and operation instructions, refer to the latest edition of the original
More information