All information correct as of 29 nd August 2013 and subject to change without notice CORRECT AS OF

Transcription

1 All information correct as of 29 nd August 2013 and subject to change without notice 1 CORRECT AS OF

2 Liquid and gas sampling tool introduction. Safety has been given paramount consideration with all of the components securely packaged in one anti-impact stainless steel housing allowing this tool to be rough handled and transit in work baskets. Environment has featured with primary and secondary product isolation valves. Product description: Tooling designed to capture gas or liquids escaping underwater for the purpose of recovery to surface for analysis. This tool is designed to be deployed from the surface with zero pressure in the containment bottles. Sample filling relies on pressure differential between the isolated sea level pressure inside the bottles and the surrounding ambient sea water pressure Introduction. Multi cutter. Available exclusively from Ashtead Technology, the Vortex Mul= Cu?er is a flexible hydraulic cu?er, suitable for cuang a wide range of materials from wires, casing, dyneema and aluminium to mooring lines, dredge hose, hydraulic hose etc. Can be used as a full grab cu?er or a basic half blade cu?er, with our without grab arm mounts, and can also be operated in air. Motor can be operated in air Vortex Mul= Cu?er is powered by the proven Vortex dredge motor / mechanical sealing system for con=nued, oil =ght reliability. Three blade op=ons are available in the kit to allow cuang of for example: Fiber rope up to 160mm or more Pennant steel wire rope up to 75mm or more Steel pipes up to 150 mm diameter Mooring line up to 160 mm diameter Scaffold tube 5000kg or more slings Dredge / plas=c / rubber hose up to 150mm diameter Your safety is your responsibility. Please ask if you are unsure about anything. 2

3 Introduction. Specifications Safety and operating limits Multi cutter assembly options. Grabber arm operation. Cutting operation. Blade options. Sample cuts. Changing blades. Removing grabber arm. Hydraulic connections to ROV Trouble shooting. Contacts. Your safety is your responsibility: If you don t know, please ask. 3

4 Actual depth of cut with 400mm blade =130 mm Cutter motor hydraulic flow required = 20 lpm (5 gpm) minimum (with 17cc motor) 50 lpm (13 gpm) maximum (with 17cc motor) Cutter motor hydraulic pressure required = 103 bar (1500 psi) minimum 241 bar (3500 psi) maximum Overrun valve standard YES Direction run valve standard YES Coupling compensator required = NO Grab arm hydraulic pressure required = 200 psi minimum / 1000 psi maximum Operating depths = Unrestricted Operate Motor in air YES Full grab tool weight in air = 30 kg / 66lb Half blade tool weight in air = 24 kg / 52lb Your safety is your responsibility: If you don t know, please ask. P!

5 Safety: Personal protec,on equipment recommended for use when working on ship/plarorm deck Hard hat Safety glasses Gloves Safety boots Overalls Operating limits Unlimited water depth. Risks Normal Operations Sharp edges on cucng blades. Please be careful with blades. Working with equipment under pressure (hydraulics or water) Hydraulic oil spillage Your safety is your responsibility: If you don t know, please ask. 5

6 Sample tool components: Secondary isolator valve. Manifold block. Main isolator valve. Contained sample pressure Sample bleed off valve. Connect here to draw off sample or to pull a vacuum on sample bottle when working in very shallow water. Cutter comes assembled as full grab cutter. Remove components as desired to operate as basic half blade cutter. Full grab cutter with grab arm mounts and mechanism installed. Weight = 30 kg in air (66lb) Basic half blade cutter with grab arm mounts and mechanism removed. Weight = 24 kg in air (52lb) H!

7 Multi cutter; Operation ROV flies into product in this case160mm diameter mooring line, closes clamp onto rope and feeds rope into blade with clamp arm mm diameter Mooring master mooring line. The same system applies to SK75 DYNEEMA shown, wire rope, steel pipes etc. 7

8 mm diameter metal cutting disc mm multi purpose serrated, tungsten edge mm diameter custom made fiber ROPE cutting blade. 4. ALL blades are considered CONSUMBLES to be charged to each job. Z!

9 inch pennant wire.120 seconds to cut kg lifting sling.1 second to cut x 40 x 3 aluminum. 2 seconds to cut 4. 1 ¼ inch crane wire. 30 seconds to cut inch, 2 wire 5000psi hydraulic hose. 7 seconds to cut 6. 2 inch scaffold tube. 5 seconds to cut inch drill casing 10mm thick. 3 minutes to cut 150mm deep inch Mooring line. 4 seconds to cut 9. 3 inch SK75 Dyneema. 2 seconds to cut inch Mooring line. 2 seconds to cut 11 4 inch dredge hose. 2 seconds to cut mm mooring chain. Average 5 minutes to cut

10 Shaft locking spanner here. 1. Open grabber arm. 2. Remove these three bolts and spacers. 3. Fit locking spanner. 4. Shaft bolt is LEFT HAND THREAD so turn clockwise to remove. 5. Fit appropriate drive plate to shaft, fit disc, fit outer plate, turn bolt counter clockwise to tighten. Torque bolt to 80 ft/lbs. 10

11 1. Remove these bolts and spacers. 2. Store ALL bolts and components in an orderly way in the kit for reassembly. 3. Fit spacers back into main chassis where necessary to regain structural integrity of chassis. 11

12 1. Remove these bolts and spacers. 2. Store ALL bolts and components in an orderly way in the kit for reassembly. 3. Fit spacers back into main chassis where necessary to regain structural integrity of chassis. 12

13 Hydraulic connections to ROV. Pressure compensated flow control for use only with fiber rope cuter and serrated blade to restrict flow to 20lpm maximum. Fill hydraulic motor and case drains with clean oil before start up. Motor can also be run in air. Hydraulic hose fitted with clear markings to facilitate mobilization times. Pressure and return hoses have identical pressure rating to avoid chance of failure through incorrect assembly 13

14 relief set at 500psi to limit closing force of arm. Fill hydraulic motor and case drains with clean oil before start up and bleed hoses. Hoses are 3000 mm long Motor can also be run in air. Hydraulic hose fitted with clear markings to facilitate mobilization times. Pressure and return hoses have identical pressure rating to avoid chance of failure through incorrect assembly 14

15 Trouble Shooting Symptom: Multi Cutter not working. Remedy: 1. Ensure that the hydraulic hoses are connected as per manual drawings and match connection labels. 2. Check that correct hydraulic flow and pressure is seen at the Multi Cutter motor. 3. Check any quick connect fittings you may have in the circuit as they can sometimes be faulty. 4. Are your thrusters using most of the available system flow and starving your circuit feeding the Multi Cutter? 5. Ensure the Vortex case drain is connected directly to tank. It is preferable to connect as close as possible to the reservoir and not run any hoses through quick connects. 6. Check that the over spin valve is operating correctly and does not have dirt ingress causing fluid to bypass the check valve. Replace with SUN valve, part number HCV 2743 as necessary. Symptom: Grab arm not working. Remedy: 1. Ensure that the hydraulic hoses are connected as per manual drawings and match connection labels. 2. Check that correct hydraulic flow and pressure is seen at the Multi Cutter motor. 3. Check any quick connect fittings you may have in the circuit as they can sometimes be faulty. 15

16 Vortex Dredge Contacts Joe Goodin - Managing Director VORTEX International Ltd, 27 Parrs Road, RD1, New Plymouth, New Zealand Tel/Fax: +64 (6) , Mobile: + 64 (0) , joe@vortexdredge.com, In association with Ashtead Technology: ABERDEEN Ashtead Technology Ltd Ashtead House, Discovery Drive, Arnhall Business Park, Westhill, Aberdeenshire AB32 6FG Tel: +44 (0) , aberdeen@ashtead-technology.com SINGAPORE Ashtead Technology Loyang Offshore Supply Base, 25 Loyang Crescent, Block 302, Unit TOPS Ave 3, PO Box 5157, SINGAPORE Tel: , singapore.sales@ashtead-technology.com HOUSTON Ashtead Technology Inc, Park Row, Suite 170, Houston, TX 77084, U.S.A Tel: , Fax: , offshore@ashtead-technology.com SCOPE ENGINEERING (Ashtead Technology Agent) Scope Engineering (WA) Pty Ltd 35 Stuart Drive, Henderson, Western Australia 6166 T: F: , Perth@ashtead-technology.com