Pro-Stringer Tennis Quick Start Stringing Instructions
|
|
- Edwin Warren
- 5 years ago
- Views:
Transcription
1
2 For a full instructional video on how to string a tennis racket using Pro-Stringer visit Section 1 - Setting up your Pro-Stringer 1. Unpack and layout the contents of the Pro-Stringer carry bag on a suitable work table Select the table clamp and tighten it firmly to the middle of the table 2. Screw the mounting post into the table clamp and tighten firmly 3. Place the rotational racket bar on top of the mounting post and ensure that it spins freely Pro-Stringer 2012 Page 1 of 8
3 4. Place the racket on the rotational racket bar with the handle of the racket at the end of the rotational racket bar that contains the length adjustment thumb wheel - refer to the photo Adjust the thumb wheel on the rotational racket bar to suit the length of the racket head 5. Secure the racket to the rotational racket bar by placing the frame retainers over the threaded lugs of the rotational racket bar at both the top and bottom of the racket head Complete the mounting process by using the butterfly screws to firmly fix the racket to the rotational racket bar 6. Select the desired stringing tension in pounds (lbs) by turning the tension control knob on the Pro- Stringer An indicator 'needle' identifies the tension selected 7. Plug the power adapter into the Pro-Stringer and secure by tightening the safe guard Plug the power adapter into a wall socket NOTE: Use an appropriate power plug adaptor where necessary Pro-Stringer 2012 Page 2 of 8
4 Section 2 - Stringing Your Racket - "Main Strings" Measure off the required amount of string needed for the main strings (vertical strings) and cross strings (horizontal strings) of the racket NOTE: Stringing can be undertaken with one continuous length of string for both the main strings and the cross strings of racket (2 tie off knots). Alternatively, two lengths of string, one for main strings and one for the cross strings can be used (4 tie off knots). These following instructions are for the scenario using two lengths of string. 1. Weave the middle two strings through the racket frame and down to the opposite end of the frame Pull the strings through the frame and ensure each string is the same length 2. Using the wider flying clamp, clamp the two middle strings, L1 and R1 together (L1 = Left 1 and R1 = Right 1 from the middle of the main strings) Continue to weave the string on both the left and right hand sides of the racket frame until the main strings are complete. NOTE: Weaving and tensioning can be completed one string at a time or as in the case with these instructions all of the main strings are pre-woven and then tensioned one string at a time Pro-Stringer 2012 Page 3 of 8
5 3. Commence tensioning by lifting up the selected string, in this case L2 and placing the string through the string guide of the Pro-Stringer Move the Pro-Stringer up against the frame of the racket 4. Place the string deeply into the rotary tensioning head and press the blue tensioning button 5. The Pro-Stringer rotary tensioning head will turn applying tension to the string When the rotary tension head stops turning and the green light illuminates the desired tension has been reached 6. Use the second clamp and clamp L1 and L2 firmly at the top of and as close to the frame as possible Make sure the clamp is secure and holding the tension Press the tensioning button and release the string from the machine The rotary tensioning head will return to the original position Pro-Stringer 2012 Page 4 of 8
6 7. Rotate the racket and select the next string to tension, in this case L3 and repeat steps 3-6 Continue this process for all of the main strings on the left and right side of the racket NOTE: For the main stings rotate the racket to tension each string 8. When all of the main strings have been tensioned, tie off the left and right side of the main strings using a half-hitch knot and repeat this knot twice Cut off any remaining string, leaving 1cm tag from the knot 9. Remove the clamps The main strings have now been completed Pro-Stringer 2012 Page 5 of 8
7 Section 3 - Stringing Your Racket - "Cross Strings" 1. Start the cross stringing process by tying off the string using the same half-hitch knot used to secure the main strings at the top of the frame Weaving the cross string under and over each main string until the opposite side of the frame is reached Pull the remaining string through the frame and tension the first string using the same process as described for the main strings 2. Weave the 2nd cross string under and over each main string using the opposite pattern as used with the first cross string Tension the 2nd cross string 3. Clamp the 1st and 2nd cross strings as close to the frame and Pro-Stringer as possible Pro-Stringer 2012 Page 6 of 8
8 4. Weaving and tensioning can be completed one string at a time or as in the case with these instructions all of the remaining cross strings are pre-woven and then tensioned one string at a time NOTE: For the cross strings rotate the racket to tension each string 5. When all of the cross strings have been tensioned clamp as close to the frame and Pro-Stringer as possible 6. Release the tension and remove the Pro-Stringer Tie off the cross strings using a half-hitch knot and repeat this knot twice 7. Cut off any remaining cross string at the top and bottom of the frame, leaving a 1cm tag from each knot Adjust the strings by hand to make sure the main and cross strings are perfectly straight and evenly aligned Pro-Stringer 2012 Page 7 of 8
9 8. Remove the butterfly screws and frame retainers Take the racket from off the rotational racket bar Dismantle and pack away the Pro-Stringer and tools into the specific sections of the carry bag A few Useful Tips String tensions can be impacted by many factors including court type, ball type. Weather conditions, player style etc. As a starting point we suggest a tension of 52lb. As you begin to understand how these factors impact your game, tensions can be adjusted accordingly. Remember that in general terms: o The faster the court, balls and playing conditions, the more control you need, so a higher tension is required to compensate for such conditions o The slower the court, balls and playing conditions, the more power you need, so a lower the tension is required to compensate for such conditions If you plan on stringing a racket that is not going to be used for a few days consider increasing the tension, as racket string tensions naturally drop over time Enjoy your Tennis Pro-Stringer 2012 Page 8 of 8
A: Stringing on 6 or 4 point mounting systems
Special Stringing Instructions for all CrossBow and Airflow CB Racquets Cutting out the Strings: When cutting the strings out of a CrossBow racquet, never cut all the cross strings first. The best way
More information602 STRINGING MACHINE OWNER'S MANUAL
PROGRESSION 602 STRINGING MACHINE OWNER'S MANUAL AL Issue 1- April 2000 Copyright 2000 GAMMA Sports - All Rights Reserved PROGRESSION 602 STRINGING MACHINE TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...
More informationOWNER'S MANUAL. Copyright 2003 GAMMA - All Rights Reserved
OWNER'S MANUAL AL Issue 1 - December 2003 Copyright 2003 GAMMA - All Rights Reserved OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... ASSEMBLY INSTRUCTIONS PAGE 4... MOUNTING THE RACQUET PAGE
More informationOWNER'S MANUAL. Copyright 1999 ATS - All Rights Reserved
OWNER'S MANUAL AL Issue 2 - August 19, 1999 Copyright 1999 ATS - All Rights Reserved OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... ASSEMBLY INSTRUCTIONS PAGE 4... MOUNTING THE RACQUET PAGE
More information600 / 600FC OWNER'S MANUAL
PROGRESSION 600 / 600FC OWNER'S MANUAL Issue 2 / Version E - Dec. 10, 1997 Copyright 1997 GAMMA Sports - All Rights Reserved PROGRESSION 600 / 600FC OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY
More informationX-6 STRINGING MACHINE OWNER'S MANUAL. Issue 1 - May Copyright 2004 GAMMA Sports - All Rights Reserved
X-6 STRINGING MACHINE OWNER'S MANUAL Issue 1 - May 2004 Copyright 2004 GAMMA Sports - All Rights Reserved OWNER'S MANUAL GAMMA X-6 TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3...ASSEMBLY
More informationX-6FC STRINGING MACHINE OWNER'S MANUAL. Issue 1 - May Copyright 2004 GAMMA Sports - All Rights Reserved
X-6FC STRINGING MACHINE OWNER'S MANUAL Issue 1 - May 2004 Copyright 2004 GAMMA Sports - All Rights Reserved OWNER'S MANUAL GAMMA X-6FC TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3...
More informationSTRINGING MACHINE OWNER'S MANUAL. Issue 5 - November 2012
602 STRINGING MACHINE OWNER'S MANUAL Issue 5 - November 2012 2 602 MP602-12 OWNER S MANUAL TABLE OF CONTENTS WARRANTY... PAGE 3 FEATURES... PAGE 4 ASSEMBLY INSTRUCTIONS... PAGE 5 MOUNTING THE FRAME...
More informationX-6 STRINGING MACHINE
X-6 STRINGING MACHINE MMAN-37 (MGX6-12) GAMMA SPORTS 200 Waterfront Drive Pittsburgh, Pennsylvania 15222 Phone: 800.333.0337 Fax: 412.323.0317 Visit our website at www.gammasports.com Copyright 2011 GAMMA
More informationA. TO PREPARE THE MACHINE FOR USE.
INSTRUCTION MANUAL FOR THE ML120 STRINGING MACHINE. CONTENTS: A. TO PREPARE THE MACHINE FOR USE. 1. The assembly of frame with console and tooltray. 2. Fixing the lever of the tension unit. 3. Putting
More informationHow to Restring a Badminton Racquet
Restring a badminton racquet by hand using two strings. Written By: Sabina ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION Badminton racquets become unusable when their strings are broken,
More informationX-6FC STRINGING MACHINE
X-6FC STRINGING MACHINE MMAN-36 (MGX6F-12) GAMMA SPORTS 200 Waterfront Drive Pittsburgh, Pennsylvania 15222 Phone: 800.333.0337 Fax: 412.323.0317 Visit our website at www.gammasports.com Copyright 2012
More informationX-6FC STRINGING MACHINE OWNER'S MANUAL
X-6FC STRINGING MACHINE OWNER'S MANUAL Issue 4 - November 2012 2 X-6FC MGX6F-12 OWNER S MANUAL TABLE OF CONTENTS WARRANTY... PAGE 3 FEATURES... PAGE 4 ASSEMBLY INSTRUCTIONS... PAGE 5 MOUNTING THE FRAME...
More information200 STRINGING MACHINE
200 STRINGING MACHINE OWNER S MANUAL Issue 1 - July 2010 Provided by www.gssalliance.com 200 OWNER S MANUAL TABLE OF CONTENTS WARRANTY...PAGE 2 FEATURES...PAGE 3 ASSEMBLY INSTRUCTIONS...PAGE 4 MOUNTING
More informationBeginners/Basic Fly Tying Course
` Beginners/Basic Fly Tying Course Basic Tools Vise Scissors Hackle Pliers Bobbins Bodkin/Dubbing Pick Hair Stacker Dubbing Wax Head Cement Dispenser Whip Finish Tool Wing Burning Tools Tweezers Half Hitch
More informationProduct Overview: Key Features:
APGL4 Model Tripod Product Overview: The Ravelli APGL4 is a Professional Quality Tripod providing a solid base for high-end photographic equipment. This model is all pressure treated aluminum alloy construction
More information602FC STRINGING MACHINE
602FC STRINGING MACHINE OWNER'S MANUAL Issue 7 - June 2014 2 602FC MP62F-13 OWNER S MANUAL TABLE OF CONTENTS WARRANTY...PAGE 3 FEATURES...PAGE 4 ASSEMBLY INSTRUCTIONS...PAGE 5 MOUNTING THE FRAME...PAGE
More informationVERSA BIKE RACK INSTRUCTIONS
VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than
More informationBeginners Fly-Tying Notes
Beginners Fly-Tying Notes SESSION 1 Tools Bobbin holder Threader (for dental floss!) Bodkin/ Dubbing needle (hat pins!) Vice 1 Check that: the jaws hold the sizes of hooks you want to tie on; and the stem
More informationMO Tech Challenge Info- Conference 2019
MO Tech Challenge Info- Conference 2019 General Info Competition will consist of 5 events chosen from the following list Costume Quick Change Fold a Drop Props Shift Cable Relay Leg a Platform Thread a
More information632 AccuPro Set-up & Operation
632 AccuPro Set-up & Operation Always check: Reel & Roller bearings Bent or broken blades Make sure the reel spins freely in the frame Place the Reel Into the Machine There are three lifting options for
More informationINSTRUCTION MANUAL OF THE STRINGWAY CROSS STRINGING TOOLS.
INSTRUCTION MANUAL OF THE STRINGWAY CROSS STRINGING TOOLS. 1. PERSONAL ADVISE: The Stringway cross stringing tools are designed to do a rather smart job. They are designed to be very user-friendly and
More informationMisaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii
Operator s Manual Table of Contents Operator Safety... 1 Introduction... 2 Unpacking and Setup... 3 Unpacking... 3 Setup... 4 FLYER Overview... 5 FLYER Diagram... 5 Capabilities... 5 Control Panel... 6
More informationBefore you start! Is iwalk 2.0 right for you?
Before you start! Is iwalk 2.0 right for you? Physical Abilities Requirements 1. Stair Test Before your injury, could you easily walk up and down stairs at normal speed, without using the hand rail? 2.
More information7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike
7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike Owner s Manual Made in Taiwan INDEX IMPORTANT SAFETY INFORMATION... 1 EXPLODED DRAWING... 2 PARTS LIST... 3 ASSEMBLY INSTRUCTION... 4-9 USER
More informationSPINNER RIDE GETTING STARTED GUIDE. Welcome to a personalized fitness experience for your members
This addendum accompanies your equipment documentation and is additional information concerning the heart rate features for your equipment and console. Important The heart rate feature is intended for
More informationX-Els STRINGING MACHINE
X-Els STRINGING MACHINE OWNER'S MANUAL Issue 1 - March 2009 X-Els OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3...ASSEMBLY INSTRUCTIONS PAGE 4... POWER CONNECTION & CONTROLS
More informationMiniball Coulomb Excitation Target Chamber
Miniball Coulomb Excitation Target Chamber Nigel Warr May 2011 Contents 1 The Coulomb Excitation Target Chamber 2 2 Mounting 2 3 The Heidelberg collimator 5 4 CD insert 5 5 Selecting targets 6 6 Getting
More informationStringway ML100 Review. Stringway ML100. A Review MSRP $1,195.00
Stringway ML100 A MSRP $1,195.00 The Stringway ML100 is a technical table top machine with features that are unique. The racquet support plate is adequate and the internal supports and hold down mechanics
More informationPro Line Two Wheel Pitching Machine
Pro Line Two Wheel Pitching Machine Owner's Manual CAUTIONS This machine is not a toy! Use under adult supervision only. Machine will throw balls and strikes- batters must stay alert and always wear a
More informationThe All New DIAMOND & DIAMOND BT
The All New DIAMOND & DIAMOND BT. Specs The Diamond The Diamond BT Type Badminton Badminton & Tennis Pulling Method Constant Pull Constant Pull Tension Range 10 38 lbs 10 88 lbs Tension Increments 0.1
More information#59114 Rola 2-Bike Rack Carrier (Shown Assembled) (A) (C) (B)
Use for Parts: #59114 Rola -Bike Rack System #59115 Rola 1-Bike Add-On TOOLS REQUIRED 10mm or 13/3 Socket & Wrench #59114 Rola -Bike Rack Carrier (Shown Assembled) Tray Attachment Hardware: (3) Plastic
More informationFirst Team Sports, Inc. Stellar Recreational Volleyball System
First Team Sports, Inc. Stellar Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 2 Height Labels L 2 Carabiner Clip C 3 Net Clamp M 1 ½ x 2 Hex Bolt
More informationExercise 2-3. Flow Rate and Velocity EXERCISE OBJECTIVE C C C
Exercise 2-3 EXERCISE OBJECTIVE C C C To describe the operation of a flow control valve; To establish the relationship between flow rate and velocity; To operate meter-in, meter-out, and bypass flow control
More informationTrue Tension Professional
True Tension Professional A *MSRP $3,000.00 *The True Tension Professional is a model that I have modified to include sixteen (16) racquet supports. In addition to the supports I am using clamps with no
More informationBabolat Star 5 Review. Babolat Star 5. A Review MSRP $
Babolat Star 5 A MSRP $3500.00 The Babolat Star 5 presents a technological and professional machine that uses the many years of Babolat development making this machine a reasonably priced option for any
More informationI.H.S INSTALLATION INSTRUCTIONS
I.H.S INSTALLATION INSTRUCTIONS TOOLS REQUIRED The following tools will be required for installation of your I.H.S. system. Item Qty Needed 9/16 Open End Wrench 2 3/4 Open End Wrench 1 1/2 Open End Wrench
More informationSquare Diagonal Tripod Japanese Square Filipino Diagonal Round Shear Ladder
Square Diagonal Tripod Japanese Square Filipino Diagonal Round Shear Ladder Square Lashing - Step by Step Used to fasten two spars or poles together. Start by crossing the two sticks or dowels at perpendicular
More informationCLASS CYCLE P8000 OWNER'S MANUAL JOHNSON HEALTH TECH. CO., LTD.
CLASS CYCLE P8000 JOHNSON HEALTH TECH. CO., LTD. No.26, Ching Chuan Rd., Taya Hsiang, Taichung Hsien 428, Taiwan, R.O.C. TEL: +886-4-2566700 FAX: +886-4-2560087 E-mail: sales@johnsonfitness.com http://www.johnsonfitness.com
More informationBike Rack and Spare Tire Carrier 1-1/4" Receiver
Bike Rack and Spare Tire Carrier 1-1/4" Receiver OWNER'S MANUAL Rev: 11.15.2017 Page 1 Bike Tire Carrier 1.25 Owners Manual TABLE OF CONTENTS Safety Information 2 Product Information 2 Installation 3 Installation
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationINSTALLATION INSTRUCTIONS. Parts List. Tools Required. Before You Begin. Installation. Customer Information BICYCLE ATTACHMENT JUL.
INSTALLATION INSTRUCTIONS JUL. 2006 Parts List Bicycle attachment Key plates (2) Tools Required Phillips screwdriver Flat-tip screwdriver Before You Begin Customer Information This Bicycle Attachment is
More informationHOME ASSEMBLY INSTRUCTIONS
HOME ASSEMBLY INSTRUCTIONS This Papillionaire Bicycle now belongs to you. It will take you to work, wait patiently outside your local cafe, and carry your groceries home. This is the start of your long-term
More informationT-016 ASSEMBLY MANUAL MODEL ROCK AND ROLL Main Street NE Minneapolis, MN
MODEL T-016 ASSEMBLY MANUAL ROCK AND ROLL 5280 Main Street NE Minneapolis, MN 55421 1.877.226.7824 www.kurtkinetic.com COMPONENTS Tools Required for Assembly: 17mm Wrench or Adjustable Wrench When unpacking,
More informationCYCLONE T-2500 USER MANUAL REGISTER WARRANTY ONLINE: AND RECEIVE A FREE TRAINING VIDEO DOWNLOAD MODEL
MODEL T-2500 USER MANUAL CYCLONE RISER RING AND BIKE NOT INCLUDED WITH TRAINER 2015 KINETIC BY KURT ALL RIGHTS RESERVED REGISTER WARRANTY ONLINE: WWW.KURTKINETIC.COM/WARRANTY AND RECEIVE A FREE TRAINING
More informationFinal Assembly Instructions Bikes with Quill Stems
Final Assembly Instructions Bikes with Quill Stems Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationORRA SPINNING REEL INSTRUCTION MANUAL (DRAFT)
ORRA SPINNING REEL INSTRUCTION MANUAL (DRAFT) a. Congratulations b. Pictures of Components c. Family Info d. How to Fill the Spool with Line e. Handle Assembly f. Anti-Reverse g. Drag Adjustment h. Reel
More informationUSER MANUAL. All rights reserved
USER MANUAL All rights reserved Dear User, Congratulations on purchasing your PARKIS! PARKIS is a household equipment for vertical bicycle parking which lets you free up precious storage space on the floor
More informationCHAINLESS ANCHORING SYSTEM USER MANUAL
CHAINLESS ANCHORING SYSTEM USER MANUAL Introduction..................................................... 1 Setting up the Chainless Anchoring System............................ 4 Set up Procedure............................................
More informationTechnical Service and Warranty Manual
Technical Service and Warranty Manual T hank you for selecting a Champion Bow. We feel confident you will be pleased with the performance and durability we build into each and every bow we manufacture.
More informationINSTALLATION INSTRUCTIONS
KIT CONTENTS: INSTALLATION INSTRUCTIONS PART NUMBER: DESCRIPTION: E361SXA302 roof MOUNT BICycle CARRIER SINGLE Short Carriage Bolt 1x Long Carriage Bolt 3x Over-Molded Wrench 1x Button Head Screw 2x Washer
More informationHow to tune a Djembe. 1 P a g e
How to tune a Djembe Look at rope pairs here. I always cross the ropes that almost touch as the pass through the same loop of the bottom cradle as pairs for the first row. It does very little tightening,
More informationRIPPLE TANK - with rippler & kit
GENERAL DESCRIPTION: RIPPLE TANK - with rippler & kit Cat: SW3430-001 with illuminator, rippler & kit. The ripple tank is used to investigate wave motion in a shallow trough of water to understand how
More informationUser Guide. Tripod. flowtech 75 / 100 Tripod. Part No. S S
User Guide flowtech 75 / 100 Tripod Tripod Part No. S2051-0001 S2052-0001 EN www.sachtler.com TM Copyright 2018 All rights reserved. Original Instructions: English All rights reserved throughout the world.
More informationItem # in1 Rotating Table. Inch BILLIARDS AIR HOCKEY TABLE TENNIS
Item # 45-6066 3-in1 Rotating Table 3 BILLIARDS AIR HOCKEY TABLE TENNIS 84 Inch ! WARNING: Rotating game should be done under adult supervision. Rotating table may cause a pinching hazard for young children
More informationKeep this manual to hand
INTRODUCTION You have recently purchased a BABOLAT SENSOR stringing machine - thank you for making the right choice! This manual has been written specially to help you get used to the way the machine works
More informationEls STRINGING MACHINE
Els STRINGING MACHINE OWNER S MANUAL Issue 1A - September 2010 Provided by www.gssalliance.com Els OWNER S MANUAL TABLE OF CONTENTS WARRANTY...PAGE 2 FEATURES...PAGE 3 ASSEMBLY INSTRUCTIONS...PAGE 4 POWER
More informationDrive Belt Instructions
Drive Belt Safety Do not roll, pry, twist, invert or bend the belt back on itself. Do not zip tie the belt. The acceptable temperature range for your belt drive is -53 C to 85 C. Do not lubricate the belt
More informationParts: Included in the parts box: Inner Rear Tire Tray. Inner Front Tire Tray. Trail Doc Clamp. Pivot Assembly. Trail Doc Post.
NV 2.0 2 Parts: Outer Front Tire Tray Inner Front Tire Tray Outer Rear Tire Tray Inner Rear Tire Tray Pivot Assembly Trail Doc Clamp Trail Doc Post Included in the parts box: 6mm Allen Wrench M6 Lock Washer
More informationLab 7 Rotational Equilibrium - Torques
Lab 7 Rotational Equilibrium - Torques Objective: < To test the hypothesis that a body in rotational equilibrium is subject to a net zero torque and to determine the typical tension force that the biceps
More informationWilson Baiardo Review. Wilson Baiardo. A Review MSRP $6,000.00
Wilson Baiardo A MSRP $6,000.00 Wilson has entered the rarified air of technical stringing machines with the ergonomically designed Baiardo. Several years of study by non-stringers lead to the creation
More informationARTICLE NO OUTDOOR PRO
ARTICLE NO. 11106 OUTDOOR PRO Quality Guarantee JOOLA is one of the most recognized table tennis brands in the world. Our products are designed to follow the latest safety regulations and are consistently
More informationE. Test, and if needed, adjust tips of antenna. 1. Mark will test antennas with meter at ground end of feedline bundle. Will take 10 minutes.
Project Steps Overview: A. Prepare: B. Raise up small antenna. C. Raise up large antenna. D. Connect to new bundle of 4-feedlines pulled up from ground. E. Test, and if needed, adjust tips of large antenna.
More informationArmorer s Handgun Sight Tool
Armorer s Handgun Sight Tool Product #710905 Instructions #1054680 Rev. B 2 Top Knobs Height Adjustment Screw Adjustment Wheel Front Pusher Block Top Carriage Assembly 2 Front Pusher Block Screws Bottom
More informationLectric Cycles Mid-Drive Electric Motor Installation
Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on
More informationRev. F, July 2014 Page 1 of 6 Top End
17 Rev. F, July 2014 Page 1 of 6 Top End (800) 532-8677 (727) 522-8677 fax: (727) 522-1007 XLT & XLT Jr: Fork Assembly Date: PO#: SO#: 1 1054197 1 Fork, XLT 1056850 1 Fork, XLT Jr 2 1054195 1 Footrest,
More informationTrampoline Installation Instructions
Congratulations on purchasing an Oz Trampolines Product. Following are detailed setup instructions for your trampoline. Please ensure all boxes and parts are present before continuing. Setting Up Your
More informationAlpha Ghost Review. Alpha Ghost. A Review MSRP $
Alpha Ghost A MSRP $2495.00 The Alpha Ghost represents the latest technology offering from a company that is well known for quality, value stringing machines. The Ghost incorporates the auto brake system
More informationLevel Three Blue Rope
Level Three Blue Rope Level Three consists of a combination of six fishing knots that work well in monofilament fishing line, two climbing knots and two knots used to secure heavy loads. Monofilament fishing
More informationItem # in-1 Swivel Table. Inch BILLIARDS AIR HOCKEY TABLE TENNIS
Item # 45-6066 3-in-1 Swivel Table 3 BILLIARDS AIR HOCKEY TABLE TENNIS 84 Inch Limited 90-Day Triumph Sports USA, Inc. Warranty All Triumph Sports USA, Inc. (TSU) games have a limited 90-day from date
More informationPART NUMBER: E361SXA200 DESCRIPTION: KAYAK CARRIER
A KIT CONTENTS: : Plug 16x Long Carriage Bolt 4x Hex Key 4x Button Head Screw 4x Pad Strap BASE Over-Molded Wrench 1x SnapAround 4x 1/5 : Important Notes: Minimum crossbar spread of 24". If spread is less
More informationIMPORTANT: Please read instructions carefully prior to use!
TABLE TENNIS ROBOT AMICUS ADVANCE OPERATION MANUAL IMPORTANT: Please read instructions carefully prior to use! 1. Assembly p.2 2. Control Panel (Quick Reference Guide) p.3 3. Operation p.4 3.1 Starting
More informationPaddle Bar Replacement
This procedure is to help facilitate the replacement of the 23 Paddle Bar Assembly on the ANKOM Dietary Fiber Analyzer. Note: The following items will be sent in a replacement package as part of the 23
More informationEZee Glider Manual. Tools needed for Assembly: Wrench (included) Philips Screwdriver (not included) Assembly Instructions
EZee Glider Manual Congratulations on your purchase of the EZee Glider! Your glider is designed for years of nearly carefree use by your child. These instructions include how to set up your glider and
More information1. Double the line and form a loop about 10cms long. Pass it through the eye of the hook. 2. Form an overhand knot on the eye of the hook.
42 NSW Recreational SALTwater Fishing Guide n 2011 Knots and Rigs KNOTS and RIGS Palomar knot. The palomar knot is quick to tie and forms a strong knot. It is a general-purpose connection used in joining
More informationRetrofitting Green SkiErg Handles
Materials Needed 1 replacement cord* 1 Bulldog clip Measuring tape or ruler Scissors *Contains lanolin Procedure Overview Remove the SkiErg from the wall or floor stand Remove cover plates Remove old cord
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationFinal Assembly Instructions Bikes with Threaded Headsets
Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our
More informationRustic Home Safety Gate
27980 Please read the following instructions carefully. Keep this instruction manual for future reference. Tools required: Phillips head screwdriver, drill (for top of stair installation), and pencil (not
More informationStart by crossing the two sticks or dowels at perpendicular or 90 degree angles.
Square Lashing Used to fasten two spars or poles together. Start by crossing the two sticks or dowels at perpendicular or 90 degree angles. Make a Clove Hitch on the vertical stick or dowel near the point
More informationFIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions
FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY
More informationPrince Neos 1500 Review. Prince Neos A Review $
A $1395.00 The is a lock-out machine and the natural extension of the venerable Neos 1000 Neos genre that has been around for some time. This machine, at this price, is an entry level machine that you
More informationImportant Note: Tighten lock nuts so the support tubes still swing freely see figure 2. There must be 1 2 threads of bolt past end of lock nuts.
Kit Contents: DESCRIPTION QTY. DESCRIPTION QTY. 2 Shank Assembly 1 Support Tube Assembly 1 Side Tube - Short 2 1-1/4 Shank 1 Center Tube - Long 1 3/8-16 x 2.0 Carriage Bolt 2 5/16-18 x 2.25 Carriage Bolt
More informationScout Meeting Schedule: Week 3 Theme: Pioneering A Date:
Scout Meeting Schedule: Week 3 Theme: Pioneering A Date: Time Activity Program Details Leader Responsible 15 mins. Gathering Activity Chain Gang 10 mins. Opening Ceremony Details can be found in the Scout
More informationPF30 Inspection & Maintenance Manual
PF30 Inspection & Maintenance Manual Version 1.4 (September 2011) 1 Contents 1. Warning!!!!!!!!!! 3 2. Terminology! Figure 1: POWERFAN PF30 and Drope!!!! 4! Figure 2: POWERFAN PF30 with belt guard retracted!!
More informationX-Els STRINGING MACHINE
X-Els STRINGING MACHINE MMAN-34 (MXELS-12) GAMMA SPORTS 200 Waterfront Drive Pittsburgh, Pennsylvania 15222 Phone: 800.333.0337 Fax: 412.323.0317 Visit our website at www.gammasports.com Copyright 2012
More informationRev M XLT Pro and XLT Jr Parts Book Page 1 of 6 Top End
17 1181381 Rev M. 2017.02.21 XLT Pro and XLT Jr Parts Book Page 1 of 6 Top End (800) 532-8677 (727) 522-8677 fax: (727) 522-1007 XLT & XLT Jr: Fork Assembly Date: PO#: SO#: ITEM PER BIKE DESCRIPTION 1
More informationQuad Cuff Handle kit (Pr) - Delrin Only-
Quad Cuff Handle kit (Pr) - Delrin Only- Page 2 = Fork Assembly, XLT & XLT Jr. Page 3 = Fork Assembly, XLT Pro Page 4 = Frame Assembly Page 5 = Wheels Assembly, XLT & XLT Jr. Page 6 = Accessories Rev E.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KIT CONTENTS: PART NUMBER: DESCRIPTION: E361SXA300 ROOF MOUNT BICYCLE CARRIER B9 TRIBECA Short Carriage Bolt Long Carriage Bolt 3x Over-Molded Wrench Button Head Screw 2x Washer
More informationINDEX
INDEX Using New Fly & Hook Threader... 1 Clinch Knot...2 Triline Knot...3 Blood Knot (Clinch Style)...4 End Loop/Dropper Loop...6 J.R. Loop Knot (For more bait action)...7 Shank Tie/Snelled Hooks...9 #6
More informationInstallation instructions, accessories
Volvo Car Corporation Göteborg, Sweden Installation instructions, accessories 200/300/400/700/800/900/S40/V40/S60/C70S70/V70 (-00)/V70 (00-)/S80/S90/V90/XC90 Section Group Weight (Kg/Pounds) Year Month
More informationAssembly Instructions
SAFETY AT THE HIGHEST LEVEL 6.6ft (2m) Window - Dec Platform System Assembly Instructions Temporary access device conforming to the test requirements of CSA Z271-10, CSA B354.5-07, CSA Z797-09, OH&S Act
More information84 3-in-1 Rotating Table Air Powered Hockey, Billiards, Table Tennis
Item# 45-6708 84 3-in-1 Rotating Table Air Powered Hockey, Billiards, Table Tennis Please keep this instruction manual for future reference If you have any problems with your new product, please contact
More informationMID-CUT AND FRONT CUT UNITS
MID-CUT AND FRONT CUT UNITS Instructional / Parts Manual Part Number: January 00 08 ( 0 & 0 ) & Adapter Kits ( 07, 08, 09, 060, 06 & 06) Table of Contents PROWLER GRASS CATCHER TWO PACKAGED ITEMS LIST
More informationOperation & Instruction Manual
Operation & Instruction Manual AMS Retriever Pro Mounting Instructions Play Video Diagram Assembly Adjustments Play Video Big Game Retriever Pro Set-up Play Video Assembly/Diagram Adjustments Play Video
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More informationKnots /2017. Camp and Outdoor Curriculum Manual
Knots 05-4487-01/2017 Camp and Outdoor Curriculum Manual Parts of a Rope Bight: A bend in the rope Loop: Crossing the rope over itself, creating a loop Overhand Loop: When the working end of the rope crosses
More informationCongratulations on your purchase of a JC Series Performer trike! The Performer JC Series is designed for everything from touring to commuting and
Congratulations on your purchase of a JC Series Performer trike! The Performer JC Series is designed for everything from touring to commuting and shopping in the city. The JC Series frames are made of
More information8MAY15 US RACK, Inc Falcon Drive, Madera, CA
8MAY15 US RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for Bedrail-mounted MOTORCYCLE RACK, Model 2001-4TRA WARNING: Do NOT attempt to install or use this rack without following
More informationT E N N I S EN
TENNIS 2018-2019 EN THE MOST POWERFUL OF CONTROL-ORIENTED RACKETS POWER (16X19) PLAYERS NEEDS: To master their power / For more spin Weight 300 g +/- 7g 10.5 oz Headsize Balance Length Stringing pattern
More information