Series IR1000/2000/3000

Transcription

1 CAT.E611- B Precision Regulator PAT.PEND The addition of the small size Series IR1 and the large size Series IR3 provides an increased range of flow rates from approx. l/min. to approx. 6l/min.

2 Precision Regulator Bracket and pressure gauge can be mounted from directions Mounting is possible on either the front or the back Expanded regulating pressure range The maximum set pressure has been expanded from the conventional MPa to.8mpa Compact and light weight IR1 width 35mm weight 14g (previously unavailable small size added) IR width 5mm weight 3g ( width 14%, weight 6% Compared to SMC IR) IR3 width 66mm weight 64g ( width 1%, weight 36% Compared to SMC IR4) air operated models Air operated type added to series IR Manifolding is possible Order made specifications (except series IR1, IR3) IR1 IR31 OUT OUT OUT OUT OUT Features 1

3 Modular body introduced Can be combined with AF (air filter) and AFM (mist separator). Attachments such as a pressure switch can be mounted as accessories Applicable modular sizes IR1: Modular type IR: Modular 3 type IR3: Modular 4 type (Refer to the F.R.L. Combination Catalog CAT.E5G-C for types of attachments.) Superior relief flow characteristics Relief flow has been increased by nearly 5 times (compared to SMC IR1, IR41) IR1 Conditions: Back pressure MPa IR1 Conditions: Back pressure MPa IR31 IR Relief flow l/min (ANR) Relief flow l/min (ANR) 1 Series Variations Specifications Maximum set pressure Port size Model Basic type Air operated type IR1 IR IR3 IR1 IR31 MPa MPa.8MPa Rc(PT) 1/8 Rc(PT) 1/4 Rc(PT) 3/8 Rc(PT) 1/ Order Made Specifications Symbol 1 8 T L X1 IRM Refer to page 8 for details. Specifications/Content Clean room specifications Copper-free specifications Ozone resistant specifications For high temperature For low temperature Non-grease specifications Manifold (except series IR1, IR3) Features

4 Application Examples Constant fluid pressure Balance and drive Accurate balance pressure setting TANK Since there is a large effective area for supply and exhaust, pressure setting can be done quickly. Limits pressure fluctuation when driving a cylinder, maintaining excellent static and dynamic balance. Accurate pressure setting Sensitivity within %F.S. (full span) Tension controller Contact pressure control Winding roller Drive roller Low friction cylinder Adapts to the cylinder's piston displacement, maintaining a constant pressure. Multistage control of work piece pressing force (Wrapping machine) Leak test circuit Measured object Low friction cylinder Features 3

5 Precision Regulator JIS symbol Basic type Air operated type Standard Specifications Model Max. supply pressure Min. supply pressure IR1 Basic type IR Set pressure +.5MPa Note 1) IR3 Maximum 1.MPa Set pressure + MPa Air operated type IR1 IR31 Set pressure +.5MPa Set pressure + MPa IR1:.5 to MPa IR:.5 to MPa IR3:.1 to MPa Regulating pressure range IR11:.5 to MPa IR1:.5 to MPa IR31:.1 to MPa.5 to.8mpa.1 to.8mpa IR1:.5 to.8mpa IR:.5 to.8mpa IR3:.1 to.8mpa Note ) Input signal pressure.5 to.8mpa.1 to.8mpa Sensitivity Repeatability Linearity Air consumption Port size Note 3) Note 4) Pressure gauge port Ambient and fluid temperature Weight (kg) How to Order 1 3 IR1 IR IR3 5l/min (ANR) or less (supply pressure: 1.MPa) Rc(PT) 1/8 4 Precision regulator Body size 1 IR Basic type (handle) Air operated type (series IR/3 only) 4l/min (ANR) or less (supply pressure: 1.MPa) 3l/min (ANR) or less (supply pressure: MPa) Type of setting Regulating pressure range For series IR1/.5 to MPa 1.5 to MPa.5 to.8mpa Note) The air operated type is model IR1 only. For series IR3 1.1 to MPa.1 to MPa.1 to.8mpa Note) The air operated type is model IR31 only. Rc(PT) 1/4 Within % of full span Within ± % of full span port: 9.5l/min (ANR) or less (supply pressure: 1.MPa) Exhaust port: l/min (ANR) or less (at maximum set pressure) Rc(PT) 1/4, 3/8, 1/ Rc(PT) 1/8 ( locations) 5 to 6 C (with no freezing) 4 Port size Symbol Size /8 1/4 3/8 1/ Thread type Nil Rc(PT) N NPT F G(PF) Order made 4l/min (ANR) or less (supply pressure: 1.MPa) 3l/min (ANR) or less (supply pressure: MPa) Rc(PT) 1/4 5 Application IR1 IR Within ±1% of full span IR3 Accessories Bracket and pressure gauge, see next page. port: 9.5l/min (ANR) or less (supply pressure: 1.MPa) Exhaust port: l/min (ANR) or less (at maximum set pressure) Rc(PT) 1/4, 3/8, 1/ Note 1) With the condition of no flow on the output side. Together with the set pressure, be sure to maintain a minimum differential pressure of.5mpa for models IR1 and IR, and MPa for model IR3. Note ) Applicable only to air operated types IR1 and IR31. The basic type is excepted. Note 3) Indicates the linearity of the output pressure with respect to the input signal pressure. Note 4) Air is normally being discharged to the atmosphere. 1 1

6 Series IR3 Series IR Series IR1 Specification Combinations : Standard specifications : Combination possible Blank: Combination not possible Specifications Set pressure max. MPa Set pressure max. MPa Set pressure max..8mpa Connection Rc(PT) 1/8 Connection Rc(PT) 1/4 Connection Rc(PT) 3/8 Connection Rc(PT) 1/ Bracket Accessories Pressure gauge Pressure gauge reverse mounted Connection NPT1/8 Connection NPT1/4 Connection NPT3/8 Connection NPT1/ Connection G(PF) 1/8 Connection G(PF) 1/4 Connection G(PF) 3/8 Connection G(PF) 1/ Standard specifications Order made specifications Symbol B G R N1 N N3 N4 F1 F F3 F4 IR1 IR11 IR1 Applicable model IR IR3 IR1 IR1 IR31 IR31 IR IR3 Modular Products and Accessory Combinations Description 1 Air filter Mist separator 3 L bracket 4 T bracket 5 Spacer 6 Spacer with L bracket (3 + 5) 7 Spacer with T bracket (4 + 5) IR1 AF AFM B1L B1T Y YL YT Applicable model IR / IR1 AF3 AFM3 B31L B31T Y3 Y3L Y3T IR3 / IR31 AF4 AFM4 B41L B41T Y4 Y4L Y4T <Combination example> 5 Spacer 3 L bracket 4 T bracket Approx. 133 Approx AF AFM IR AF3 AFM3 IR 34 Accessories (Optional)/Part Nos. 1 AF4 AFM4 IR3 Description Bracket Pressure gauge IR1 G33--1 IR11 P3613 G IR1 G IR G43--1 Part No. IR1 P368 G IR / 1 G IR3 G43--1 IR31 P36318 G IR3 / 31 G Accuracy ±3% (full span)

7 Construction IR1 IR IR3 Fixed throttle SUP side passage SUP side passage SUP side passage OUT side passage OUT side passage Setting spring Setting knob Diaphragm (A) Flapper OUT() Nozzle Diaphragm (B) Exhaust Diaphragm (C) OUT() Exhaust valve Main valve OUT() Valve guide Exhaust IR1 Valve guide IR31 Valve guide Operating Principle (for IR) When the setting knob is turned, the nozzle is closed by the flapper allowing the supply air that flows in from the upstream side to pass through the fixed throttle and to act on diaphragm B as nozzle back pressure, the main valve is pushed down by the generated force and the supply pressure flows out to the downstream side. The air pressure that flows in acts on diaphragm C and while opposing the force generated by diaphragm B it also acts on diaphragm A opposing the compression force of the setting spring and becomes the set pressure. If the set pressure rises too high, diaphragm A is pushed up, the interval between the flapper and the nozzle widens, the nozzle back pressure drops, the balance of diaphragms B and C is broken, the main valve closes, the exhaust valve opens and the excess pressure from the downstream side is discharged to the atmosphere. In this way fine pressure variations are detected by the nozzle/flapper type pilot mechanism, and precise pressure adjustment is performed. SUP side passage OUT side passage IN Exhaust OUT() SUP side passage OUT side passage IN OUT() Replacement parts No. Description Material Diaphragm assembly Diaphragm assembly Diaphragm Valve Valve Valve Damper O-ring O-ring O-ring O-ring O-ring Seal (A) Seal (B) Service parts kit no. (set of above items 1 through 14) NBR, other NBR, other NBR, other Stainless steel, NBR Brass, NBR Brass, NBR NBR NBR NBR NBR NBR NBR NBR NBR Note 1) IR1 uses P361-1 and IR11/1 use P361. Note ) Use mini-flick type. Note 3) IR1 uses KT-IR1 and IR11/1 use KT-IR11. Valve guide Part No. IR1 IR IR3 IR1 IR31 P361-1 P361- P361 (-1) Note 1) P3611 ø.5 x 1 ø1 x 1.3 KT-IR1 Note 3) KT-IR11 P36- P36-5 P3619 P365 P366 ø x 1.5 ø4.5 x 1 JISB41 P11 KT-IR Valve guide P36- P363-1 P3639 P3631 ø4.5 x 1 ø7.8 x 1.5 JISB41 P5 Note ) JISB41 P16 Note ) P36315 P36316 KT-IR3 P36-13 P36-5 P3619 P365 P366 ø x 1.5 ø4.5 x 1 JISB41 P11 KT-IR1 P36-13 P363-1 P369 P3631 ø4.5 x 1 ø7.8 x 1.5 JISB41 P5 Note ) JISB41 P16 Note ) P36315 P36316 KT-IR31 3

8 OUT OUT OUT OUT Dimensions IR1-1 IR- M5 x P Approx ø8.5 ø43 M6 x P 5.5 Exhaust Approx. 13 ø9.5 OUT() ø3 35 Approx. 43 OUT 1 -Rc(PT) 1/8 Port size G OUT() EXH 35 -Rc(PT) 1/8 Pressure gauge port Rc(PT) 1/4 Approx. 6 Port size Rc(PT) 1/8 Pressure gauge port Max. 4 ø1 Panel mounting hole SMC Mounting hole Bracket SMC Mounting hole Bracket ø1.5 Panel mounting hole Panel Pressure gauge Pressure gauge Max. 4 Panel ø43 IR3- M6 x P 76 Approx ø15.5 IR1- ø43 M5 depth 7 Exhaust 5 Approx Approx Rc(PT) 1/4 Port size ø9.5 IN OUT() Rc(PT) 1/8 Pressure gauge port EXH(3) OUT() 5 Mounting hole Approx. 68 Rc(PT) 1/ Exhaust port -Rc(PT) 1/4 to 1/ Port size 66 -Rc(PT) 1/8 Pressure gauge port 3 Bracket Pressure gauge Mounting hole Bracket IR31- M5 depth 7 9 ø15.5 SMC Pressure gauge ø43 EXH(3) 76 Approx. 144 IN OUT() 66 Approx. 68 Rc(PT) 1/ Exhaust port -Rc(PT) 1/4 to 1/ Port size Rc(PT) 1/8 Pressure gauge port Mounting hole 48 Bracket Pressure gauge 4

9 Series IR1 Flow rate characteristics Testing methods conform to JIS B837. Relief characteristics IR1-1 Conditions: Supply pressure MPa IR1-1 Conditions: Back pressure MPa IR1-1 Pressure characteristics Conditions: Supply pressure MPa Flow rate l/min (ANR) 4 5 Set pressure P MPa IR11-1 Conditions: Supply pressure MPa IR11-1 Conditions: Back pressure MPa IR11-1 Set pressure P MPa IR1-1 Conditions: Supply pressure 1.MPa IR1-1 Conditions: Back pressure 1.MPa IR Set pressure P MPa

10 Series IR Flow rate characteristics Testing methods conform to JIS B837. Relief characteristics IR- Conditions: Supply pressure MPa IR- Conditions: Back pressure MPa IR- Pressure characteristics Conditions: Supply pressure MPa Flow rate l/min (ANR) Set pressure P MPa IR1- Conditions: Supply pressure MPa IR1- Conditions: Back pressure MPa IR1- Set pressure P MPa IR- Conditions: Supply pressure 1.MPa IR- Conditions: Back pressure 1.MPa IR Set pressure P MPa IR1- Conditions: Supply pressure 1.MPa IR1- Conditions: Back pressure 1.MPa IR Set pressure P MPa

11 Series IR3 Flow rate characteristics Testing methods conform to JIS B837. Relief characteristics IR3-3 Conditions: Supply pressure MPa IR3-3 Conditions: Back pressure MPa IR3-3 Pressure characteristics Conditions: Supply pressure MPa Flow rate l/min (ANR) 5 Set pressure P MPa IR31-3 Conditions: Supply pressure MPa IR31-3 Conditions: Back pressure MPa IR31-3 Set pressure P MPa IR3-3 Conditions: Supply pressure 1.MPa IR3-3 Conditions: Back pressure 1.MPa IR Set pressure P MPa IR31-3 Conditions: Supply pressure 1.MPa IR31-3 Conditions: Back pressure 1.MPa IR Set pressure P MPa

12 Order Made Specifications Contact SMC regarding detailed dimensions, specifications and delivery times. Order Made 1 1 Clean Room Specifications Standard part number Note) Contact SMC if equipped with pressure gauge. Clean room specifications Specifications Cleanliness port EXH port Grease Teflon is a registered trade mark of DuPont. Class 1 With M5 fitting (applicable tube O.D. ø6) IR1/: M5 fitting (applicable tube O.D. ø6) IR3: Rc(PT) 1/ female thread T L Teflon grease External and internal copper parts are changed to stainless steel or aluminum. 3 Copper-free Specifications 4 For High and Low Temperature Environments Standard part number T Specifications Symbol Environment Ambient temperature Rubber material Standard part number Note) Contact SMC if equipped with pressure gauge. Copper-free specifications Fluoro rubber is used for rubber seal materials. 8 Ozone Resistant Specifications Standard part number Ozone resistant specifications T For high temp. environments For high/low temperature environments For high temperature For low temperature L For low temp. environments 5 to 1 C (Max. 8 C with pressure gauge) 3 to 6 C Fluoro rubber Special NBR or silicon rubber 5 Non-Grease Specifications Assembly is performed in an ordinary environment without using grease. However, since parts are not washed they are not completely oil-free. Standard part number 6 8 Set pressure and quantity 1 Accessory (pressure gauge) Nil None G IR1: G33-1 IR: G43-1 Stations stations X1 to 8 station manifold type regulators. (Contact SMC regarding 9 or more stations.) Non-grease specifications Manifold Specifications (except type IR1 and series IR3) IRM 1 3 G Body size Manifold type regulator Specifications Stations Ports 1 IR1 IR Set pressure Accessory (pressure gauge) 8 stations MPa setting 1 to n pcs. MPa setting 1 to n pcs..8mpa setting 1 to n pcs. Example 1) MPa setting with 6 stations IRM1-6G-16 Example ) MPa setting pcs., MPa setting pcs.,.8mpa setting 1pc. with 5 stations IRM-5G-11 to 8 stations Common SUP IR1: Rc(PT) 1/4, IR: Rc(PT) 3/8 Individual OUT IR1: Rc(PT) 1/8, IR: Rc(PT) 1/4 Individual EXH (from IR body) MPa, MPa and.8mpa settings can be combined G33--1 (IR1), G43--1 (IR) 8

13 Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by labels of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1), JIS B 837 Note ) and other safety practices. Caution : Operator error could result in injury or equipment damage. Warning : Operator error could result in serious injury or loss of life. Danger : In extreme conditions, there is a possible result of serious injury or loss of life. Note 1) ISO 4414 : Pneumatic fluid power -- Recommendations for the application of equipment to transmission and control systems. Note ) JIS B 837 : Pneumatic system axiom. Warning 1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications. Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements.. Only trained personnel should operate pneumatically operated machinery and equipment. Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators. 3. Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions.. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply pressure for this equipment and exhaust all residual compressed air in the system. 3. Before machinery/equipment is re-started, take measures to prevent shooting-out of cylinder piston rod, etc. ( air into the system gradually to create back-pressure.) 4. Contact SMC if the product is to be used in any of the following conditions: 1. Conditions and environments beyond the given specifications, or if product is used outdoors.. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverages, recreation equipment, emergency stop circuits, press applications, or safety equipment. 3. An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis. 9

14 Precision Regulator Precautions Be sure to read before handling. Warning 1. Screw piping together with the recommended proper torque while holding the side with female threads. Looseness or faulty sealing will occur if tightening torque is insufficient, while thread damage will result if the torque is excessive. Furthermore, if the side with the female threads is not held while tightening, excessive force will be applied directly to piping brackets, etc. causing damage or other problems. Connection thread Torque Piping Recommended proper torque N m (kgf cm) 1/8 1/4 3/8 1/ 7 to 9 (7 to 9) 1 to 14 (1 to 14) to 4 ( to 4) 8 to 3 (8 to 3) Piping Caution 1. Preparation before piping Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove cutting chips, cutting oil and other debris from inside the pipe.. Wrapping of pipe tape When connecting pipes and fittings, etc., be sure that cutting chips from the pipe threads and sealing material do not get inside. Further, when pipe tape is used, leave 1.5 to thread ridges exposed at the end of the pipe/fitting. Winding direction Expose approx. threads Pipe tape. Do not allow twisting or bending moment to be applied other than the weight of the equipment itself. Provide separate support for external piping, as damage may otherwise occur. 3. Since excessive moment loads and the propagation of vibrations, etc. can easily result from inflexible piping made of steel, etc., avoid these problems by using flexible tubing for intermediate connections. Warning Warning Operating Environment 1. Do not operate in locations having an atmosphere of corrosive gases, chemicals, sea water, water or steam, or where there will be contact with the same.. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5. In locations where there is contact with spatter from water, oil or solder, etc., implement suitable protective measures. Air Supply 1. These products are designed for use with compressed air. Contact SMC if any other fluid will be used.. Do not use compressed air which includes chemicals, synthetic oils containing organic solvents, salt, or corrosive gases, etc., as this can cause damage or malfunction. 3. If drainage is not removed from air filters and mist separators, it can flow out to the downstream side and lead to the malfunction of pneumatic equipment. In cases where the management of drainage removal will be difficult, the use of filters with auto drains is recommended. 1

15 Specific Product Precautions Be sure to read before handling. Refer to pages 9 and 1 for safety instructions and precautions. Caution Air Supply 1. If the supply pressure line contains drainage or dirt, etc., the fixed throttle can become clogged leading to malfunction, and therefore, in addition to an air filter (SMC Series AF) be sure to use a mist separator (SMC Series AM, AFM). Refer to SMC's "Compressed Air Cleaning Systems" catalog regarding air quality.. Never use a lubricator on the supply side of the regulator, as this will positively cause the fixed throttle to become clogged and lead to malfunction. If lubrication is required for terminal devices, connect a lubricator on the output side of the regulator. Warning Maintenance 1. When the valve guide (refer to construction drawing on page 3) is to be removed during maintenance, first reduce the set pressure to "" and completely shut off the supply pressure.. When a pressure gauge is to be mounted, remove the plug after reducing the set pressure to "". Precautions for IR1 only Warning 1. When remounting the valve guide after removing it for maintenance, use a tightening torque of no more than N m (6kgf cm). Since the valve guide on this product is made of resin, there is a danger of damage if tightened with a torque exceeding the prescribed value. Caution Operation 1. Do not use a precision regulator outside the range of its specifications as this can cause failure. (Refer to specifications.). When mounting is performed, make connections while confirming port indications. Caution Operation 3. If a directional switching valve (solenoid valve, mechanical valve, etc.) is mounted on the supply side of the regulator and repeatedly switched ON and OFF, wear of the nozzle/flapper section will be accelerated and a discrepancy in the setting value may occur. Therefore, avoid using a directional switching valve on the supply side. In the event a directional switching valve will be used, install it on the output side of the regulator. 4. Air is normally discharged from the bleed port (the hole on the side of the body's midsection). This is a necessary consumption of air based on the construction of the precision regulator, and is not an abnormality. 5. Be sure to tighten the lock nut after pressure adjustment. Precautions for IR3, IR31 only Caution 1. The supply pressure is relatively high (approx. MPa or more), the set pressure is low (approx. MPa or less), and when operated with the output side released to the atmosphere, there may be pulsations in the setting side pressure. In this kind of situation, operate with the supply pressure reduced as much as possible, or increase the set pressure somewhat and restrict the output line (add and adjust a stop valve, etc.).. The capacity of the output side is large, and when used for the purpose of a relief function, the exhaust sound will be loud when being relieved. Therefore, operate with a silencer (SMC Series AN) mounted on the exhaust port (EXH port). The connection is Rc(PT) 1/. Precautions for IR1, IR31 (air operated type) only Caution 1. Since the output of types IR1 and IR31 is the same pressure as the input signal pressure, select a type of regulator (general purpose or precision type) for input signal pressure adjustment according to the application.. The screw on the topmost section is a zero point adjustment screw which is locked at the factory and requires no adjustment for operation. 11

16 DiskArt 1988 Austria SMC Pneumatik GmbH (Austria). Girakstrasse 8, A-1 Korneuburg Phone: 6-68, Fax: Germany SMC Pneumatik GmbH Boschring 13-15, D-6339 Egelsbach Phone: 613-4, Fax: Netherlands SMC Controls BV De Ruyterkade 1, NL-111 AB Amsterdam Phone: , Fax: Slovenia SMC Slovenia d.o.o. Grajski trg 15, 836 Zuzemberk Phone: Fax: Belgium SMC Pneumatics N.V./S.A. Nijverheidsstraat, B-16 Wommelgem Phone: , Fax: Greece S. Parianopoulus S.A. 9, Konstantinoupoleos Street, GR Athens Phone: , Fax: Norway SMC Pneumatics (Norway) A/S Wollsveien 13 C, granfoss Noeringspark N-134 Lysaker, Norway Phone: , Fax: Spain SMC España, S.A. Zuazobidea 14, Pol. Ind. Jundiz, E-115 Vitoria Phone: , Fax: Czech SMC Czech.s.r.o. Kodanska 46, CZ-1 1 Prague 1 Phone: , Fax: Hungary SMC Hungary Kft. Budafoki ut , 1117 Budapest Phone: , Fax: Poland Semac Co., Ltd. PL-5-75 Wesola k/warszaway, ul. Wspolna 1A Phone: , Fax: Sweden SMC Pneumatics Sweden A.B. Ekhagsvägen 9-31, S-1415 Huddinge Phone: , Fax: Denmark SMC Pneumatik A/S Jens Juuls vej 3, DK-86 Viby J Phone: , Fax: Ireland SMC Pneumatics (Ireland) Ltd. Citywest Business Campus, Naas Road, Saggart, Co. Dublin Phone: , Fax: Portugal SMC España (Sucursal Portugal), S.A. Rua de Engº Ferreira Dias 45, 41 Porto Phone: , Fax: Switzerland SMC Pneumatik AG Dorfstrasse 7, CH-8484 Weisslingen Phone: , Fax: Estonia Teknoma Eesti AS Mustamäe tee 5, EE-6 Tallinn, Estonia Phone: 5953, Fax: Italy SMC Italia S.p.A Via Garibaldi 6, I-61 Carugate, (Milano) Phone: -9711, Fax: Romania SMC Romania srl Vasile Stroescu 19, Sector, Bucharest Phone: , Fax: Turkey Entek Pnömatik San. ve Tic Ltd. Sti. Perpa Tic. Merkezi Kat: 11 No: 165, TR-87 Okmeydani Istanbul Phone: , Fax: Finland SMC Pneumatiikka OY Veneentekijäntie 7, SF-1 Helsinki Phone: , Fax: Latvia Ottensten Latvia SIA Ciekurkalna Prima Gara Linija 11, LV-16 Riga, Latvia Phone: , Fax: Russia SMC Pneumatik LLC Centrako Business Centre 13, Bolshoy Prospect V.O., St. Petersburg Phone: , Fax: DiskArt UK Vincent Avenue, Crownhill, Milton Keynes, MK8 AN Phone: Fax: France SMC Pneumatique, S.A. 1, Boulevard de Strasbourg, Parc Gustave Eiffel Bussy Saint Georges F-7767 Marne La Vallee Cedex 3 Phone: , Fax: Lithuania UAB Ottensten Lietuva Savanoriu pr.18, LT-6 Vilnius, Lithuania Phone/Fax: Slovakia SMC Slovakia s.r.o. Pribinova ul. C. 5, 819 Bratislava Phone: , Fax: OTHER SUBSIDIARIES WORLDWIDE: ARGENTINA, AUSTRALIA, BOLIVIA, BRASIL, CANADA, CHILE, CHINA, HONG KONG, INDIA, MALAYSIA, MEXICO, NEW ZEALAND, PHILIPPINES, SINGAPORE, SOUTH KOREA, TAIWAN, THAILANDIA, USA, VENEZUELA For more information, please contact your local SMC Regional Centre SMC UK Regional Centres BELFAST Tel: Fax: Northern Ireland Regional Centre Suite 3, Shaftesbury House, Edgewater Road Belfast BT3 9JQ BIRMINGHAM Tel: Fax: Birmingham Regional Centre 4 The Courtyard, Gorsey Lane, Coleshill Warwickshire B46 1JA BRISTOL Tel: Fax: Bristol Regional Centre 5 East Gate Office Centre East Gate Road, Eastville, Bristol BS5 6XX SMC UK Distributors Birmingham JAMES LISTER Tel: Fax: Blackburn BLACKBURN PNEUMATIC SYSTEMS LTD Tel: Fax: Bristol APPLIED AUTOMATION Tel: Fax: CRAWLEY Tel: Fax: Crawley Regional Centre 9 Pelham Court, Pelham Place, Broadfield Crawley RH11 9AZ CUMBERNAULD Tel: Fax: Scottish Regional Centre 1 Carradale Crescent, Broadwood Business Park, Cumbernauld Glasgow G69 9LE DROITWICH Tel: Fax: Droitwich Regional Centre Hampton Park, Hampton Lovett Droitwich, Worcestershire WR9 NX Bury St Edmunds PNEUMATIC LINES Tel: Fax: Cardiff WALES FLUID POWER Tel: Fax: IPSWICH Tel: Fax: Ipswich Regional Centre Unit 6 & 7, Alpha Business Park Whitehouse Road, Ipswich, Suffolk IP1 5LT MANCHESTER Tel: Fax: Manchester Regional Centre 3 Modwen Road, Waters Edge Business Park Ordsall Lane, Salford, Manchester M5 3EZ MILTON KEYNES Tel: Fax: Vincent Avenue, Crownhill, Milton Keynes MK8 AN East Grinstead AUTARKY AUTOMATION Tel: Fax: Newton Ayciiffe ONCAD AUTOMATION Tel: Fax: NEWCASTLE Tel: Fax: Newcastle Regional Centre Unit B6, Marquis Court, Marquis Way Team Valley Trading Estate, Gateshead Tyne & Wear NE11 RU POOLE Tel: Fax: Poole Regional Centre Unit 4, Acorn Business Centre, Ling Road Poole, Dorset BH1 4NZ SHEFFIELD Tel: Fax: Sheffield Regional Centre Unit 4, North Anston Business Park Houghton Road, North Anston, Sheffield S31 7JJ Plymouth APPLIED AUTOMATION Tel: Fax: Redditch MULTI-PNEUMATICS Tel: Fax: SMC CORPORATION Shimbashi, Minato-ku, Tokio 15 JAPAN; Phone: Fax: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.