Bridge Plugs, Ball Drop & Caged Ball Plugs For Zone Isolation
|
|
- Juniper McKenzie
- 6 years ago
- Views:
Transcription
1 Bridge Plugs, Ball Drop & Caged Ball Plugs For Zone Isolation ADVANTAGE composite bridge plug, caged ball and ball drop (flow thru) frac plug provide a means to isolate multiple zones during high pressure stimulation frac operations. The Bridge Plug is designed to temporarily plug a well or to provide isolation from either above or below the isolation point. The Ball Drop (flow thru) Frac Plug allows for fluid to flow from above and below the isolation point until the ball is pumped down from the surface and seated on top of the composite frac plug. The operator can pressure up against the frac plug to achieve isolation. Due to the composition of the material, the plugs can be easily milled and circulated back to surface. APPLICATIONS: Single or multiple zone stimulation Vertical, horizontal, deviated, or multilateral wellbores Efficient in a wide range of environments High-pressure/ High-temperature wells FEATURES: Holds full differential pressure from above and below (plug). Multiple plugs may be run to isolate a series of zones. Full composite, one-piece body and components provide fast drill-out times. Top-drillable, these plugs drill out safely and quickly with conventional tri-cone or junk mill bits. Can be set on wireline using conventional setting tools. All tools capable of setting with a Baker 10. Light weight particles minimize plugging up surface equipment. Drop ball available in multiple specific gravities. Custom OD also available to suit heavy weight casing.*
2 CASING PLUG SPECS (Bridge Plug, Ball Drop, Caged ball) O.D. Weight lb./ft. Min I.D. Max I.D. Max O.D. Max ID In. Pressure Rating,psi. OAL In. Operating Temp. F Setting Tool Adapters 4-1/ K / 350 Baker / K 10K 300/ 350 Baker / K /350 Baker K /350 Baker K /350 Baker 20 PRE-RUN INSPECTIONS: 1. Inspect slips, packing element for cuts, cracks, or shipping damage. Do not run the tool if damage is noticed. 2. Confirm the tool is in the correct weight range for the well casing the tool will be run 3. Inspect dimensions on plug such as outside diameter (OD) of the tool. 4. Verify the correct number of shear pins and holes are present for accurate shear during the setting of the tool. PRECAUTIONS & HANDLING: 1. The use of equipment contrary to manufacturer s specification may result in a tool failure, or complications. 2. Do not support the weight of the tool string by the plug. 3. Protect the tool from damage during pick-up and installation in the lubricator/wellhead. 4. Slow down when entering the top of the liner. 5. If the fluid level is not known, run the tool in slowly until it is known that the tool is in the fluid. RUNNING PROCEDURE: 1. The maximum pump rate is 15 bbl/m 2. The run-in speed for wireline application is recommended at 400 ft/m maximum. 3. Once the plug is set, slowly fill the hole with fluid to prevent a hammer effect on the plug. 4. Upon entering the curve of the well, slowly begin pumping 3 bbl/min and increase to approximately 6 bbl/min at a 45 inclination. Up to 12 bbl/min may be pumped while approaching 90 from horizontal.
3 MILLING PROCEDURE: The best mill for milling a composite plug with jointed pipe is a PLUGBUSTER PDC mill. This type of mill will reduce the possibility of casing damage during mill-up of the composite plug. The proper bit size should be 92 95% of casing drift diameter. Rotary speeds from RPM are recommended. Tag plug with PLUGBUSTER and begin circulation to wash any loose debris from top of plug. Circulation rates of bbl/m are recommended. Pick-up 12 inches and begin rotation. Set down 5,000 8,000 lbs while rotating. The set-down weight and pump rate will dictate the milling time required. Maintain slack-off weight until the plug is removed. MILLING RECOMMENDATION: These practices and techniques have been developed through testing and field runs with the goal of achieving the optimal technique. However, it should be noted that a variety of parameters could affect the milling out of a plug. The milling/drilling techniques can and should change to meet those changing conditions. MILLING WITH COILED TUBING & MOTOR: Mill size Recommendation for the proper mill OD should be 95 98% of the casing drift diameter. Mill type PLUGBUSTER PDC milling bit. Mill watercourse The width of the watercourse can determine the size of the cuttings that are circulated. Typically, the larger the width and depth of the watercourse will generate larger cutting returns. The smaller the watercourse, the smaller the returns will be. The desired results should be taken into consideration when choosing the mill s watercourse size and configuration. A good recommendation is to use a watercourse width between ⅜ ½ Weight on bit (WOB) 500 2,000 lbs is optimum. The maximum amount of WOB should be used if needed. Flow rate 1 3 bbl/m The flow rate will determine the motor s rpm. The flow rate also affects the WOB. Too high of a flow rate can produce a stand off affect and thus reduce the WOB. However, do not exceed the motor manufacturer s maximum flow rate. Bottom hole assembly A junk basket should be used to keep cuttings from collecting above the motor or in the annulus area around the coil tubing motor assembly. It is also recommended that a motor assist device be used when milling with coil tubing motors. We recommend minimum motor torque 900 ft/lbs.
4 SETTING FORCE REQUIREMENTS: CBP- Size Wt. Range Pressure Rating Setting Force Setting Tool 4-1/ # 17.10# 25,000 lbs (5 pins) Baker # 25,000 lbs (5 pins) Baker / # 30,000 lbs (6 pins) Baker # 40,000 lbs (8 pins) Baker 20 WIRELINE ADAPTER KIT SCHEMATICS: *** Each steel pin equivalent to 5,000 lbs***
5 Item # Part Description 1 Wireline Adapter Kit - Crossover 2 Tension Mandrel 3 Wireline Adapter Kit Setting Sleeve 4 Wireline Adapter Kit Pin on Adapter 5 Composite Bridge Plug 6 Composite Bridge Plug Setting Ring 7 Composite Bridge Plug - Mandrel
North American sealing solutions Bridge Plug Ball Drop Frac Plug Caged Ball Frac Plug
North American sealing solutions Bridge Plug Ball Drop Frac Plug Caged Ball Frac Plug The North American Sealing Solutions composite bridge plug, caged ball and ball drop (flow thru) frac plug provide
More informationHydro-Mech Bridge Plug
Manual No: 0620000303 Revision: F Approved By: Quality Engineer Date: 2014-9-9 Hydro-Mech Bridge Plug DESCRIPTION: Map Hydro-Mech Bridge Plug is hydraulically actuated and mechanically set. Compact, with
More informationDB Bridge Plug. Features. Benefits. Applications
DB Bridge Plug The WELLFIRST Premium Cast Iron Bridge Plug designed to run on electric line. Rated between 2000-10000-psi differential, and 300 F from above and below. Features Field Proven Design Constructed
More informationSCORPION HIGH-QUALITY, FULLY COMPOSITE PLUGS
SCORPION HIGH-QUALITY, FULLY COMPOSITE PLUGS A DIFFERENT KIND OF ENERGY COMPANY Nine Energy Service isn t your typical oilfield services company. Our success stems from a culture driven by performance
More informationCoiled Tubing string Fatigue Management in High Pressure Milling Operation- Case Study
Coiled Tubing string Fatigue Management in High Pressure Milling Operation- Case Study Abstract: Paper Presenter: Ebrahim Rabbani 1 e.rabbani@mehranservices.com Ebrahim Rabbani, Danial Davoodi 2, Fatemeh
More informationfloat equipment OPERATING MANUAL TYPE 505/506 Float Equipment 1. INFORMATION & RECOMMENDATIONS Float Equipment
Contents 1. GENERAL INFORMATION & RECOMMENDATIONS 1 2. INSTALLATION FLOAT EQUIPMENT 2 2.1 PRE-USE FIELD INSPECTION 2 2.2 POSITION FLOAT ON CASING STRING 3 3. RUNNING OF FLOAT EQUIPMENT 3 3.1 CIRCULATION
More informationPerforating Options Currently Available in Horizontal Shale Oil and Gas Wells. Kerry Daly, Global BD Manager- DST TCP
MENAPS 2013 Perforating Options Currently Available in Horizontal Shale Oil and Gas Wells Kerry Daly, Global BD Manager- DST TCP MENAPS 13-17 WELL FLOW MANAGEMENT TM Scope/ Contents: MENAPS 13-17 Study
More informationModel A Sleeve Valve Cement Retainer
Ret. O.D. Model A Sleeve Valve Cement Retainer DIMENSIONAL DATA A B C D E F G H J K L M N P Q R 3.593 3.593 3.500 2.500 3.531 3.531 1.345 3.375.750.437 2.437 2.187 7.062 2.437 5.312 11.685 20.093 3.937
More informationFloat Equipment TYPE 925/926
Type 925 Float Collar Plunger Valve Float Equipment For less demanding well conditions, such as shallower depths or lower pressures, Top- Co offers economical float equipment certified to API RP 10F category
More informationTAM Single SeT inflatable
TAM Single SeT inflatable ReTRievAble PAckeRS Sets with pressure only Releases with straight pull or rotate Ideal for horizontal applications Sets in casing or open hole Runs on tubing, coiled tubing,
More informationOn-Off Connector Skirt
On-Off Connector Skirt Retrievable Packers & Accessories The On-Off Connector Skirt is compact, reliable, fully sealing, J-type tubing disconnect device that automatically engages and releases with a small
More informationType 967 Diamond Broaching Type 968 Sidewinder reamer shoe
Type 965 float collar Type 966 float shoe 1. GENERAL INFORMATION & RECOMMENDATIONS Type 967 Diamond Broaching Type 968 Sidewinder reamer shoe Type 969 Sidewinder reamer shoe Float Equipment Top-Co Float
More informationOCEAN DRILLING PROGRAM
BIH OCEAN DRILLING PROGRAM www.oceandrilling.org Scientifi c Application Packers A packer is an inflatable rubber element that inflates to seal the annular space between the drill string and the borehole
More information2-7/8 TRIPLE PORTED PBL BYPASS SYSTEM
RECEIVING PBL AT RIG SITE TITLE: Operating Instructions for 2-7/8 Triple Port PBL 1-10-201 2-7/8 TRIPLE PORTED PBL BYPASS SYSTEM OPERATING INSTRUCTIONS 1. On receipt of PBL Bypass Tools at Rig site, the
More informationFREQUENTLY ASKED QUESTIONS
What are some applications in which you ve successfully used this product? New Completions - Stage by Stage Diversion Between Frac plugs for Intra-Stage Diversion Replace Frac Plugs with Perf PODs - Full
More informationHydroPull. Extended-Reach Tool. Applications
Extended-Reach Tool HydroPull This tool incorporates a cycling valve that momentarily interrupts the flow to create water-hammer pressure pulses inside coiled or jointed tubing used in horizontal well
More informationOPERATING MANUAL DOUBLE ACTING DRILLING INTENSIFIER HYDRAULIC TYPE
Page 1 of 8 OPERATING MANUAL DOUBLE ACTING DRILLING INTENSIFIER HYDRAULIC TYPE Size Series 6.50" 478 Reviewed And Approved By: Signature: Initials: Date: Page 2 of 8 Section OPERATING MANUAL DOUBLE ACTING
More informationChapter 5 HORIZONTAL DRILLING
Chapter 5 HORIZONTAL DRILLING Chapter 5 How much money am I about to put on the table for a horizontal well? Did I do sufficient planning? Keys to Successful Horizontal Wells Multi-disciplined teams working
More information6-3/4 DUAL PORTED PBL BYPASS SYSTEM (Applicable to sizes 6-1/4 & 6-1/2 also)
RECEIVING PBL AT RIG SITE TITLE: Operating Instructions for -3/4 PBL -3/4 DUAL PORTED PBL BYPASS SYSTEM (Applicable to sizes -1/4 & -1/2 also) OPERATING INSTRUCTIONS 1. On receipt of PBL Bypass Tools at
More informationAdvanced Applications of Wireline Cased-Hole Formation Testers. Adriaan Gisolf, Vladislav Achourov, Mario Ardila, Schlumberger
Advanced Applications of Wireline Cased-Hole Formation Testers Adriaan Gisolf, Vladislav Achourov, Mario Ardila, Schlumberger Agenda Introduction to Cased Hole Formation tester Tool specifications Applications
More informationE NGINEERED C EMENTING S OLUTIONS
DART CATCHER TOOL Blackhawk s Dart Catcher Tool provides indication of the exact location of downhole fluids during inner string cement jobs, cementing squeezes, or balanced cement plugs for temporary/permanent
More informationStandard Operating Procedures
Standard Operating Procedures GlassBore and GlassLine EUE 8RD Tubular Goods Composite Lining Systems Focus on Safety and Quality COMPOSITE LINING SYSTEMS Table of Contents Section 1 page 3 Arrival on Production
More informationOman Central Gas Velocity Strings in deep tight gas wells. September th European Conference on Gas Well Deliquification.
Oman Central Gas Velocity Strings in deep tight gas wells September 2009-4th European Conference on Gas Well Deliquification. Velocity Strings Oman Central Gas Agenda: - Objectives - Completions - VS design
More informationSPE MS. Copyright 2015, Society of Petroleum Engineers
SPE-173678-MS Cost Effective Solutions to Achieve Injection Post Toe Valve Failure Cody Trebing, Thru Tubing Solutions; Jeff Whitworth, Thru Tubing Solutions; Alex Beszterda, ConocoPhillips Copyright 2015,
More informationARTICLE. Overcome casing integrity issues in your plug-and-perf operations
ARTICLE Overcome casing integrity issues in your plug-and-perf operations CONTENT A challenge to plug-and-perf success 3 Causes of casing restrictions 9 How extended-range frac plugs keep operations moving
More informationOptimising Hydraulic Energy to Dramatically Improve Lateral Reach
Optimising Hydraulic Energy to Dramatically Improve Lateral Reach What Affects Reach? Build angle Size of completion CT size Drag Mechanical Fluid Debris in well BHA size End load CT size End load Buoyancy
More informationFLOAT EQUIPMENT AND CASING ACCESSORIES
FLOAT EQUIPMENT AND CASING ACCESSORIES CONTENTS INTRODUCTION... 2 FLOAT EQUIPMENT... 4 Standard Valve... 4 Differential Valve... 5 SPECIALITY FLOAT EQUIPMENT Double Valve Float Shoes... 6 Float Equipment
More informationNorth Dakota Petroleum Council Re-stimulation Initiative
North Dakota Petroleum Council Re-stimulation Initiative Refracs: Completion Discussion for Bakken Generation 1 Wellbores Originally presented to the Interim Energy Development and Transmission Committee
More informationPerforation Design for Well Stimulation. R. D. Barree Barree & Associates LLC
Perforation Design for Well Stimulation R. D. Barree Barree & Associates LLC Typical Shaped Charge Primer charge Main explosive charge Case or container Detonating cord groove ¾ point of initiation Liner
More informationPRESSURE TESTING REPORT
Tejas Research & Engineering, LLC 9185 Six Pines Drive The Woodlands, Texas 7738 PRESSURE TESTING REPORT Nexgen - 5352 - Plug Testing (Plug #2) Casing Drift: 4.375" 29-Sep-16 Plug OD: 4.25" Tools: T4 Hydraulic
More informationInstallation Operation Maintenance
682 Seal Cooler New generation seal cooler to meet and exceed the seal cooler requirements stated in the 4th Edition of API Standard 682 Installation Operation Maintenance Experience In Motion Description
More informationRPSEA UDW Forum June 22 & 23, Secure Energy for America
RPSEA UDW Forum June 22 & 23, 2010 Secure Energy for America PROJECT TEAM RPSEA Operator Advisory Committee Anadarko Chevron Shell ConocoPhillips Subcontractors IntecSea NOV CTES General Marine Contractors
More informationSubsea Safety Systems
Subsea Safety Systems The ELSA-HP has been developed to service the high pressure horizontal tree completion and intervention market. With systems designed and qualified up to 15,000 psi, 250 degf and
More informationPowerDrive X6. Rotary Steerable System for high-performance drilling and accurate wellbore placement
Rotary Steerable System for high-performance drilling and accurate wellbore placement The PowerDrive X6 RSS maintains control under the most difficult conditions, bringing the benefits of rotary steerable
More informationRig Math. Page 1.
Page 1 The Calculator and Main Keyboard Display Numerical 10-key pad used for entering numerical values Trigonometric Functions These keys will be used where wellbore angle is an issue These are the keys
More informationInflatable Packer Single & Double. Single & Double Packer Dimension. Wireline Packer. Water Testing Packer (WTP) Packer
Inflatable Packer Single & Double Single & Double Packer Dimension Wireline Packer Water Testing Packer (WTP) Packer Packer Working Pressure & Depth Chart Packer Water Hand Pump Packer Air Driven Pump
More informationWellwork Chronological Regulatory Report
Well Name: UNIVERSITY 49 #0808H Field: Lin (Wolfcamp) S/T/R: / / County, State: Location Desc: Operator: Enduring Resources, LLC Project Type: Completion District: Southern Project AFE: DV02151 AFE's Associated:
More informationRestoring Fluid Flow in Tubing Strings
Restoring Fluid Flow in Tubing Strings Andrew Roth, Product Manager Fike Corporation Fike Hydraulic Tubing Drains (HTD) for use with deep hole drilling tools, downhole devices and other oil and off shore
More informationHPHT Annular Casing Packer. Obex Annular Casing Packer
HPHT Annular Casing Packer Obex Annular Casing Packer Industry Challenge Casing packer to support second stage cement Reduce hydrostatic pressure on formation Get cement to surface Annular gas migration
More informationPROPOSED NEW SUB- CODE 1 RIG UP AND TEAR. Possibly Fits into Existing Code. 7/26/2018 Review PROPOSED NEW CODE EXISTING OPERATION
NW NW 1 RIG UP AND TAR 1 no sub-code RIG UP AND TAR DOWN Start: Rig released from previous well, nd: Rig fully rigged up, acceptance tests successfully completed, and signed off. DOWN 1 1 Rig Under Tow
More informationWELL SCAVENGER. Versatile wellbore clean-up tool for the most demanding operations
WELL SCAVENGER Versatile wellbore clean-up tool for the most demanding operations WELL SCAVENGER: A versatile wellbore cleanup tool for flowrestricted applications The inability to recover wellbore debris
More informationTYPE 3710 CARTRIDGE SPLIT SEAL Technical Specification
A Mating Ring B Mating Ring/ Retaining Ring C Mating Ring/ Clamp Ring D Mating Ring Adapter E Primary Ring F Primary Ring/ Retaining Ring G Finger Springs H Spring Retainer I Gland O-ring J Flat Gasket
More informationMultiple Activated Bypass Tool. P roduct I nf ormation. Landrill oiltools. Version Aug 2017
Multiple Activated Bypass Tool P roduct I nf ormation Landrill oiltools Version 2.1.3 Aug 2017 1 Multiple Activation Bypass Tool 1Bi 1.Brief fintroduction ti The LANDRILL Multiple Activation Bypass Tool
More informationRetrievable Bridge Plugs
Retrievable Bridge Plugs & Associated Equipment Well Intervention omega-completion.com Our Philosophy High performance and integrity The Omega range of Retrievable Bridge Plugs and our accompanying suite
More informationCasing Design. Casing Design. By Dr. Khaled El-shreef
Casing Design By Dr. Khaled El-shreef 1 Casing Design CONTENTS Function of Casing Casing Types & Tools Strength Properties Casing Specification Casing Design 2 1 RUNNING AND CEMENTING CASING Reasons for
More informationBP SIT Testing Franks Facility Lafayette
BP SIT Testing Franks Facility Lafayette General Information Status: Franks test well Lafayette La. Rig: Franks Test Rig Casing: 13 3/8, 0 to 4,600 Workstring: 4 ½ IF Brine: Fresh Water Directional: Straight
More informationDynamic Underbalance (DUB)
Dynamic Underbalance (DUB) Perforating Cam Le Perforating Product Champion Agenda Overview DUB Software Tools Case histories 2011 HALLIBURTON. ALL RIGHTS RESERVED. 2 Dynamic Underbalance Software Dynamic
More informationWILD WELL CONTROL WARNING SIGNS OF KICKS
WARNING SIGNS OF KICKS Warning Signs of Kicks Learning Objectives You will learn the warning signs that indicate the well may be kicking: Warning signs of kicks False kick indicators You will also learn
More informationNeoProducts, LLC 1201 Dealers Ave. Harahan, LA Ph:
Please read this entire document. It concerns all 9⅝ Vented Thru-tubing Bridge Plugs Read this document before proceeding to NeoProducts Recommended Best Practices for 9⅝ vented T- TBPs. Whenever running
More informationACCURACY, PERFORMANCE, AND HANDLING OF OIL-FILLED DIGIQUARTZ PRESSURE INSTRUMENTATION
Application Note Doc. G8108-001 Rev. A - 23-Jul-02 ACCURACY, PERFORMANCE, AND HANDLING OF OIL-FILLED DIGIQUARTZ PRESSURE INSTRUMENTATION For more information regarding Digiquartz products contact: Paroscientific,
More informationMOCS. Multiple Opening Circulation Sub. Fluid Bypass Valve
MOCS Multiple Opening Circulation Sub Fluid Bypass Valve 1 Applications BHA Protection o o Pumping LCM Spotting Acid Work-over and completions o o o Well bore cleanout Fluid displacements Bottoms-up circulation
More informationDebris Management Drilling Tools
Debris Management Drilling Tools Protecting BHA components during well construction Remove drilling debris from the wellbore before it creates expensive problems. Debris commonly causes downhole tool failure,
More informationINTERMEDIATE CASING SELECTION FOR COLLAPSE, BURST AND AXIAL DESIGN FACTOR LOADS EXERCISE
INTERMEDIATE CASING SELECTION FOR COLLAPSE, BURST AND AXIAL DESIGN FACTOR LOADS EXERCISE Instructions Use the example well data from this document or the powerpoint notes handout to complete the following
More informationEP WELLS DAILY OPERATIONS REPORT Report 38 07/18/2017
1 Company Type bore WBS No/API No PERMIAN Development 30265014 / 4230133171.00 Event Summary Event Type Completion only Event Start Date 04/28/2017 Days on Location 37.00 Objective Install Completion Original
More informationCATALOGUE FISHING TOOLS FISHING TOOLS
CATALOGUE FISHING TOOLS CONFIND S.R.L. Str. PROGRESULUI Nr. 2 CÂMPINA cod. 105600 ROMÂNIA Tel. : 0244/ 374719 Fax : 044/ 373709 ; 333160 e-mail: confind@confind.ro 2 Progresului st., 105600 Campina, Romania
More informationPasquale Imbò e Marco Pelucchi ENI S.pA;
7th European Gas Well Deliquification Conference Innovative Failsafe Capillary Injection System Resolves Liquid Loading in Gas Well with a Cost- Effective Solution that Maintaining Production and Well-Safety
More informationSpecial Note: Single Pawl Spacer is required when using a Ratchet Pawl Assembly.
Line Overview The automatic spring-fed knives feature of this tool prevents excessive strain from being applied from the rig floor that could cause the knives to burn or break before the cut is completed.
More informationPJD Connection. . TenarisHydril Running Manual.. Recommended guidelines for the field inspection of TenarisHydril connections, FSOG
IDM Code GDL23470/1 / March 2018 TenarisHydril PJD Connection Scope These guidelines apply specifically to the use of TenarisHydril PJD connections. This document should be used in conjunction with the
More informationW I L D W E L L C O N T R O L SNUBBING OPERATIONS
SNUBBING OPERATIONS Snubbing Operations Learning Objectives You will learn - Various activities suitable for snubbing operations. Best practices and techniques for conducting snubbing operations. The types
More informationRST INSTRUMENTS LTD.
RST INSTRUMENTS LTD. Borehole Packers Instruction Manual Copyright 2016 Ltd. All Rights Reserved Ltd. 11545 Kingston St., Maple Ridge, B.C. Canada V2X 0Z5 Tel: (604) 540-1100 Fax: (604) 540-1005 Email:
More informationVortexFlow DX (Downhole) Tool Installation Instructions
VortexFlow DX (Downhole) Tool Installation Instructions www.vortextools.com Page 1 of 10 The VortexFLOW tools are based upon Technology that is a result of U.S.A. patents 6,151,751; 6,659,118; 6,749,374;
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Types A & B
Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)
More informationBVM CORPORATION TYPE AAX TONG 55,000 FT/LBS. TORQUE Part number: Serial Number:
BVM CORPORTION TYPE X TONG 55,000 FT/LBS. TORQUE Part number: Serial Number: WRNING: Manual tongs which have experienced excessive wear or are found to have cracks should be replaced or repaired by BVM
More informationSURFACE CASING SELECTION FOR COLLAPSE, BURST AND AXIAL DESIGN FACTOR LOADS EXERCISE
SURFACE CASING SELECTION FOR COLLAPSE, BURST AND AXIAL DESIGN FACTOR LOADS EXERCISE Instructions Use the example well data from this document or the powerpoint notes handout to complete the following graphs.
More informationTesting Services Overview
2 Jet Research Center JRC Jet Research Center Perforating Center of Excellence Testing Services Overview API RP19B Testing Advanced Testing Operational Testing API RP19B Testing The American Petroleum
More informationIWCF Equipment Sample Questions (Combination of Surface and Subsea Stack)
IWCF Equipment Sample Questions (Combination of Surface and Subsea Stack) 1. Given the volumes below, how much hydraulic fluid will be required to carry out the following operations (no safety margin)?
More informationRIH intermediate section casing in Bazian-1 exploration oil well
Energy and Sustainability V 559 RIH intermediate section casing in Bazian-1 exploration oil well A. K. Darwesh Petroleum Engineering Department, Engineering Faculty, Koya University, Kurdistan Abstract
More informationMS Back-up, Spiral
MS 28782 Back-up, Spiral 1. Material: MIL-R-8791. 2. Surface must be smooth and free from irregularities. 4. Z gap dimension to be met with retainer over a mandrel of M diameter +.000 -.002. 5. Dash numbers
More informationOperating Procedures for GripTight 15.5 SDR & IPS Test Plugs
EST Group DC2518 08/01 REV 3 12/12 Page 1 of 6 Operating Procedures for GripTight SDR & IPS Test Plugs WARNING For proper operation, GripTight plugs must be assembled as shown in Figure 1. Pressure testing
More informationECD Reduction Tool. R. K. Bansal, Brian Grayson, Jim Stanley Control Pressure Drilling & Testing
ECD Reduction Tool R. K. Bansal, Brian Grayson, Jim Stanley Control Pressure Drilling & Testing Drilling Engineering Association, Fourth Quarter Meeting November 20, 2008 1 Presentation outline Description
More informationW I L D W E L L C O N T R O L PRESSURE BASICS AND CONCEPTS
PRESSURE BASICS AND CONCEPTS Pressure Basics and Concepts Learning Objectives You will be familiarized with the following basic pressure concepts: Defining pressure Hydrostatic pressure Pressure gradient
More informationDRILLSCENE PROACTIVE DRILLING DECISIONS
DRILLSCENE PROACTIVE DRILLING DECISIONS RISE TO THE CHALLENGE OF REAL-TIME DRILLING CONTROL Today s oil and gas drilling operations present significant technical challenges in remote locations and increasingly
More informationThe key to connectivity
The key to connectivity Kerry Daly, Global BD Manager, Tubing Conveyed Perforating (TCP) First published by Oilfield Technology, November 2015 Connecting oil or gas-bearing formations with the wellbore
More information// ADapters GUIDelines
// ADapters GUIDelines ADAPTER SELECTION Selection of an appropriate ALFAGOMMA adapter for a given application depends on the fluid system operating parameters listed below and the tube material and wall
More informationWellwork Chronological Regulatory Report
Well Name: UNIVERSITY 09A #1003H Field: Lin (Wolfcamp) S/T/R: / / County, State: Location Desc: Operator: Enduring Resources, LLC Project Type: Completion District: Southern - ERPBU Project AFE: DV02251
More information1 Scope... 2 Functions of cementing float equipment... 3 Definitions... 4 Calibration... 5 Test Categories... 6 General...
American Petroleum Institute Contents Page 1 Scope... 2 Functions of cementing float equipment... 3 Definitions... 4 Calibration... 5 Test Categories... 6 General... 7 Apparatus and Materials... 8 High-temperature/high-pressure
More informationBest Practices - Coiled Tubing Deployed Ball Drop Type Perforating Firing Systems
Best Practices - Coiled Tubing Deployed Ball Drop Type Perforating Firing Systems As a result of a recent job incident utilizing a Ball Drop Type firing system deployed on coiled tubing, the following
More information2013 Premium Connections
2013 Table of Contents 1. Introduction 1 1.1 Quality and Manufacturing 2 2. TMK 3 2.1 Application Guide 4 2.2 Options 8 2.3 Tubing Connections. Integral ULTRA FX 12 Tubing Connections. Threaded and Coupled
More informationAPPENDIX A1 - Drilling and completion work programme
APPENDIX A1 - Drilling and completion work programme Information about the well and drilling To the extent possible, the international system of units (SI) should be adhered to, and the drilling programme
More informationOiltools PRODUCT CATALOGUE
Oiltools PRODUCT CATALOGUE Archer is a global oilfield service company with more than 40 years experience, over 7,000 employees, and operations in over 118 locations worldwide. From drilling services,
More informationPerforating Center of Excellence TESTING SERVICES OVERVIEW
Perforating Center of Excellence TESTING SERVICES OVERVIEW Jet Research Center (JRC) is the leader in energetic research and testing for the oil and gas industry. Since introducing jet perforators for
More informationDownhole Gas Separators
Gas Well De-Liquification Workshop Denver, Colorado February 27 March1, 2006 Downhole Gas Separators A Laboratory and Field Study Jim McCoy, Echometer Company Tony Podio, University of Texas at Austin
More informationStudy Guide IADC WellSharp Driller and Supervisor
Times to Flow Check: Before pulling out of the hole Before pulling BHA into the BOP When bit is pulled into the casing Increase in cuttings at shakers with same ROP On connections Upon abnormal trip tank
More informationTorque Turn Tests on Q-Slip Sleeve holding down screws Ref: RP/2014 Eng. Jan A
Torque Turn Tests on Q-Slip Sleeve holding down screws Ref: RP/2014 Eng. Jan - 001-A 5 januari 2014 A High level Look in to the holding forces from a grub-screw locking mechanism Author- Marco Kacgin -
More informationCoal Bed Methane (CBM) Permeability Testing
Coal Bed Methane (CBM) Permeability Testing WTN Network Meeting April 28-29, 2011 ExxonMobil Exploration / Well Testing Team CBM Flow Characteristics Flow mechanism Gas desorbs when pressure drops below
More informationFORGE Energy UL 21 Pahaska 1H API Number:
FORGE Energy UL 21 Pahaska 1H API Number: 42-495-33740 10/26/2016 07:00 HPJM 07:15 Install 1502 Adapter Flanges to Well Head. RU Pump Truck test lines to 1000 PSI no leaks. Load hole w/ 15 bbls fresh water.
More informationAlong-string pressure, temperature measurements hold revolutionary promise for downhole management
Along-string pressure, temperature measurements hold revolutionary promise for downhole management IT S WIDELY KNOWN that the majority of stuck pipe incidents occur while pulling out of hole. If we can
More informationIntroduction to Through Tubing Rotary Drilling
Introduction to Through Tubing Rotary Drilling By: LEAding Edge Advantage International Ltd Old Stoneywood Church Bankhead Road Bucksburn, Aberdeen AB21 9HQ Tel 44-1224-716969 Fax 44-1224-712333 Email:
More informationIWCF Equipment Sample Questions (Surface Stack)
IWCF Equipment Sample Questions (Surface Stack) 1. During a well control operation 4000 psi was shut in below the middle pipe rams. Ram type BOP data: Model: Cameron U type Rated Working Pressure: 15000
More information4400 TwinHybrid Gas Seal
4400 TwinHybrid Gas Seal EQUIPMENT PREPARATION MECHANICAL SEAL INSTALLATION INSTRUCTIONS 1 2 200.005" 0,13 mm 125 µ" 3,2 µm R a 3 4 32 µ" 0,8 µm R a 1000 ±.002" 0,05mm CAUTIONS These instructions are general
More informationInstruction Manual. PE-25/32/37 Tapping Machines. POLYTAPP Valves
Instruction Manual PE-25/32/37 Tapping Machines & POLYTAPP Valves Nov 2016, Revision 2 Document Number 3000111 2 M.T. Deason Company, Inc. PO Box 101807 Birmingham, AL 35210 Phone: 205 956 2266 Fax: 205
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Type C
Module Type Width Length C 22-27 56-63 Side-of-Pole Mount for 1 Module (SPM1) For Module Type C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 022212-1 Side-of-Pole Mount
More informationSTUDY OF DRILLING SYSTEM IN RELEVENCE TO FIELDS IN NORTH EAST PART OF INDIA BY M/S HALLIBURTON
STUDY OF DRILLING SYSTEM IN RELEVENCE TO FIELDS IN NORTH EAST PART OF INDIA BY M/S HALLIBURTON OBJECTIVE To engage a reputed consultancy firm /consultants having multidisciplinary expertise for a. Facilitate
More informationCased-Hole Logging Environment
Cased-Hole Logging Environment 2 Planning a Production Logging Job Planning is an important part of a production logging job. Frequently these jobs can only be done in safety during daylight. Thus, the
More informationW I L D W E L L C O N T R O L COMPLICATIONS
COMPLICATIONS Complications Learning Objectives You will learn to detect changes that deviate from established trends. You will learn how to respond to problems such as: Pump problems String problems Hole
More informationW I L D W E L L C O N T R O L COMPLETIONS AND WORKOVERS
COMPLETIONS AND WORKOVERS Completions & Workovers Learning Objectives You will learn - The reasons why a well needs to be worked over. The benefits derived from working a well over. To prepare a well completion.
More informationTOOLS FOR BREAKDOWN ELIMINATION
TOOLS FOR BREAKDOWN ELIMINATION BITTEKHNIKA BITTEKHNIKA company was founded in 1996 and it is still developing dynamically. These are the traditions and innovative technologies in design and production
More information5k Slickline Lightweight Pressure Control Equipment 4 ID
5k Slickline Lightweight Pressure Control Equipment 4 ID Table of Contents 5k Slickline Lightweight Pressure Control Equipment 4 ID... 1 Hydraulic Slickline Stuffing Box... 3 Wireline Lubricators... 4
More informationThe Time Has Come For Coiled Rod. Reprinted from Well Servicing magazine
The Time Has Come For Coiled Rod Reprinted from Well Servicing magazine The development of flush-by well service units and stand-alone coiled rod injector head technology has helped grow the coiled rod
More informationSqueeze Cementing. Brett W. Williams Cementing Technical Advisor January 2016 Tulsa API Meeting
Squeeze Cementing Brett W. Williams Cementing Technical Advisor January 2016 Tulsa API Meeting Definition Squeeze Cementing is the process of applying hydraulic pressure to force or squeeze a cement slurry
More information