ME 472 Engineering Metrology

Transcription

1 ME 472 Engineering Metrology and Quality Control Chp 11 - Limits and Limit Ga(u)ges Mechanical Engineering University of Gaziantep Dr. A. Tolga Bozdana Assistant Professor

2 Various Types of Limit Gauges Cylindrical Pin Gauge Adjustable Snap Gauge Plain Ring Gauge Thread Plug Gauge Cylindrical Plug Gauge Progressive Cylindrical Plug Gauge Adjustable Thread Ring Gauge 1

3 Taylor s Theory of Gauging This theory is the key to design of limit gauges, which defines the function (i.e. the form) of most limit gauges. GO gauge checks the Maximum Material Condition (MMC), and it should check as many dimensionsi as possible. NOT-GO gauge checks the Least Material Condition (LMC), and it should only check one dimension. Min. Width Maximum Material Condition (MMC) Min. Length Least Material Condition (LMC) Max. Length Ma ax. Width GO gauge is used to ensure that MMC is not exceeded. Thus, it should be made to MMC based on wear and gauge tolerances, which are explained in the following sections. However, if NOT-GO gauge is made to both dimensions of LMC, a condition would arise where the width of work is within specified limitsit whereas the length is oversize. Such a gauge will not enter the work, and hence the work will be accepted although its length is outside the limits (see the figure). Thus, a separate NOT-GO gauge is required for each individual dimension. WORK GO Gauge NOT GO Gauge Actual Length (Oversize) Actual Widt th NOT-GO gauge is always relatively shorter, and approximately equal in length to the hole diameter. GO gauge should be equal in length to about three or four diameters. This would enable to check that the MMC is not exceeded due to geometric errors (e.g. straightness as illustrated in figure). Length of GO plug gauge prevents it entering a non-straight hole 2

4 Tolerances in Limit Gauges For a hole to be checked, GO gauge is a cylinder with diameter equal to the minimum hole size whereas NOT-GO gauge is a cylinder with diameter equal to the maximum hole size. It is vice versa for a shaft to be checked. However, it is not simple due to the fact that limits of size are required for work which states that nothing can be made to an exact size, including gauges. The gauge maker needs a tolerance to which gauges may work. So, defining the gauge tolerance relative to the nominal gauge size is critical. For instance; when the gauge tolerance increases GO gauge size but decreases NOT-GO gauge size, then the gauge will tend to reject good work which is near the upper or lower size of limits. If the otherwise happens, the gauge will tend to accept doubtful work which is just outside the specified limits. This decision has been made in BS 969 as follows: 1) The tolerance on GO gauge shall be within the work tolerance zone. 2) The tolerance on NOT-GO gauge shall be outside the work tolerance zone. Allowances must also be made for the initial wear which occurs on a new gauge. Thus, the tolerances shall be: 1) Gauge tolerance = 10% of work tolerance 2) Wear allowance = 5% of work tolerance 3

5 Tolerancing System and Wear Allowance There are two systems for gauge tolerances: unilateral and bilateral In unilateral system; the gauge tolerance zones lie entirely within the work tolerance zone. The disadvantage of this system is that certain parts may be rejected as if they were outside the limits. In bilateral system; the gauge tolerance zones are bisected by high and low limits of work tolerance zone. The disadvantage is that parts within the working limits can be rejected and parts outside the working limits can be accepted. In modern limit systems, unilateral system is usually preferred. Measuring surfaces of GO gauges constantly rub against the surfaces of parts in inspection, thus they loose their initial size due to wear. Therefore, to prolong the service life of gauges, wear allowance (i.e. 5% of work tolerance) is added to nominal dimension of GO plug gauge whereas subtracted t from nominal dimensioni of GO snap gauge. Wear allowance is not considered for NOT-GO gauge as it is not subjected to much wear. Single Limit (Unilateral) Double Limit (Bilateral) 4

6 A Case Study on Gauge Design Suppose that size of the hole to be tested is: 25 ± mm Highest limit of hole = mm Lowest limit of hole = mm Work tolerance = = 0.04 mm Gauge tolerance = 10% of work tolerance = mm Wear allowance = 5% of work tolerance = mm Nominal size of GO plug gauge = = mm Nominal size of NOT-GO plug gauge = mm Dimension of GO plug gauge: Dimension of NOT-GO plug gauge: If bilateral system was used, the gauge dimensions would be as follows: Dimension of GO plug gauge: Dimension of NOT-GO plug gauge: For testing a shaft using snap gauge, the order of tolerances and wear allowance must be reversed: Size of GO gauge = = mm Dimension of GO snap gauge: Dimension of NOT-GO snap gauge:

7 Pros and Cons of Limit Gauges The advantages of limit gauges can be summarised as follows: Conveniently used in mass production for controlling various dimensions. Can easily be used by semi-skilled people. Economical in their own cost as well as engaging cost. The followings are the limitations/disadvantages of limit gauges: Do not indicate the actual size of the component Susceptible for wear, expansion and collapse Need for large space for storage of gauges g Cannot handle finer quality jobs due to precision issues Require frequent checking of gauge g dimensions 6