Electrical Safety For Managers Updated For E. ElectricalTrainingPro.com
|
|
- Eunice Bradley
- 6 years ago
- Views:
Transcription
1 Electrical Safety For Managers Updated For E Daryn Lewellyn ElectricalTrainingPro.com Fatalities From Exposure To Electricity Bureau of Labor Statistics 1
2 Fatalities From Exposure To Electricity Bureau of Labor Statistics Electrical Safety Three Legged Stool Installation -NFPA 70 National Electrical Code(NEC) -OSHA Maintenance -NFPA 70B Recommended Practices For Electrical Equipment Maintenance -Manufacturers Requirements NFPA 70E Chapter 2 Electrical Safety Program -NFPA 70E Standard For Electrical Safety In The Workplace -OSHA
3 OSHA & 70E Want You To De-Energize 5 Working On Deliberately Coming In Contact With Live Circuit Parts Diagnostic Testing Troubleshooting Visual Inspection Repair Alter The Circuit Tightening Connections Removing/Replacing Components 6 3
4 Hierarchy Of Risk Control Most Effective Risk Control Method Elimination Substitution Engineering Controls Example De-energize, Lockout tagout. PLC viewing ports or external laptop ports. Mitigate incident energy. Least Effective Awareness Administrative Controls PPE Signs, barricades, briefings. Training & field audits. Arc rated clothing, insulated tools, rubber gloves, etc. 7 Electrical Safety Program Job Safety Planning & Briefing Completed and documented by a qualified person. Description of job, electrical hazards, results of shock and arc risk assessments. Work procedures, precautions & energy source control. Job Briefing Cover job safety plan. Information on Energized Electrical Work Permit. (If one is required.) Change in scope. 8 4
5 Electrical Safety Program Incident Investigation Close Calls - Near Misses Injuries Fatalities 9 Emergency Response Training Second Person, Safety Watch, or a Crafts Person First Aid CPR Training AED If One Available Training shall occur at a frequency that satisfies the requirements of the certifying body. Verify & document annually that training is current Contact release training annually. 10 5
6 E Article 350 Safety-Related Work Requirements: Research and Development Laboratories Major Changes Electrical Safety Authority(ESA) Documentation Shutdown Procedures Specific Hazards Tools, Training, & Maintenance Custom Built Equipment Energy Thresholds Electrically Safe Work Condition 11 Unused Openings 12 6
7 Exposed Live Conductors Missing Knockouts Missing Receptacle Cover Plates Damaged Enclosures Receptacles And Switches Exposed While Painting 13 Can Be A Very Dangerous Device Ground Fault Circuit Interrupters (GFCI) Outdoors Maintenance & Construction Hubbell 14 7
8 15 Work Involving Electrical Hazards Energized Electrical Work Permit Within the restricted approach boundary Or if you interact with the equipment, even if live parts are not exposed, but there is an increased likelihood of an arc flash 16 8
9 Work Involving Electrical Hazards Exemptions To Energized Electrical Work Permit Diagnostics, voltage measurement, etc. If the restricted approach boundary is not crossed: Thermography, ultrasound, or visual inspections, Accessing an area with energized electrical equipment if no electrical work is performed General housekeeping and miscellaneous non-electrical tasks 17 Electrical Safety Training Shall Be Familiar With: Special Precautionary Techniques Policies & Procedures PPE Insulating & Shielding Materials Test Equipment OSHA Definition: Qualified Person One who has received training in and has demonstrated skills and knowledge in the construction and operation of electric equipment and installations and the hazards involved. You Can Be Qualified In Respect To Some Equipment & Tasks But Not Others 18 Photo Courtesy Of Bulwark 9
10 Electrical Safety Training Trained At A Minimum On: Distinguishing Live Parts Determine Nominal Voltage Approach Distances Perform Job Safety Planning Identify Electrical Hazards Assess The Risk Select Risk Controls Test Equipment Selection Absence Of Voltage Test Document 19 Photo Courtesy Of Bulwark Retraining Triggers Tasks that are performed less often than once per year Employee noncompliance New technology or new equipment Changes in procedures Safety related work practices not normally used Duties change Every three years 20 Photo Courtesy Of Bulwark 10
11 Retraining Triggers Lockout/Tagout Retraining When Procedures Are Revised Every 3 Years Non-Compliance Demonstrate Proficiency Document 21 Host & Contractor Documented Meeting Host Responsibility Contractor Responsibility Known Hazards That Might Not Be Recognizable Information Needed To Make Risk Assessments Report Any Observed Violations Instruct Employees On The Hazards Communicated Ensure 70E & Hosts Policies Are Followed Communicate To Host: Unique Hazards They May Create Hazards They Find Corrective Actions & Prevention Concerning Any Violations 22 11
12 Arc Flash Boundary Arc Rated PPE Required 1.2 cal/cm2 (5 J/cm2) 2nd Degree Burn in 1 Second Restricted Approach Boundary EEWP Trigger Insulated Gloves & Shock PPE Limited Approach Boundary ESWC Trigger 23 Determining Arc Rating Only one method can be used on the same piece of equipment & label. Incident Energy Analysis Method PPE Category Method You are not allowed to use the results of an incident energy analysis to specify a PPE category. 24 Photo Courtesy Of Oberon 12
13 13
14 Arc Flash Hazard Incident Energy Analysis Field Work/Data Collection Engineering Implementation A Living Document 27 Electrical Safety For Managers Updated For E Daryn Lewellyn daryn@electricaltrainingpro.com ElectricalTrainingPro.com
Leader s Guide ERI Safety Videos
1717 SAFE ELECTRICAL WORK PRACTICES & THE 2018 NFPA 70E Leader s Guide ERI Safety Videos SAFE ELECTRICAL WORK PRACTICES & THE 2018 NFPA 70E This easy-to-use Leader s Guide is provided to assist in conducting
More informationNFPA 70E What Changed? Keeping People Safe from Electrical Hazards for over 50 Years
NFPA 70E -2018 What Changed? Keeping People Safe from Electrical Hazards for over 50 Years Moderator Ron Spataro AVO Training Institute Marketing Manager Q&A Send us your questions and comments during
More informationPreview to the 2018 NFPA 70E, the Standard for Electrical Safety in the Workplace
Preview to the 2018 NFPA 70E, the Standard for Electrical Safety in the Workplace Preview to the 2018 NFPA 70E, the Standard for Electrical Safety in the Workplace Technical Committee Members James Dollard,
More informationManagement Plan for Electrical Safety ISD #535
Management Plan for Electrical Safety ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9 ½ Street Rochester, MN 55904 507-328-4507 MANAGEMENT PLAN FOR ELECTRICAL SAFETY Table of Contents
More informationNECA Personal Protective Equipment (PPE) Selector
NECA Personal Protective Equipment (PPE) Selector Objectives Explain why electrical contractors should follow the precautions set forth in NFPA 70E List the hazards which demonstrate why an arc flash risk
More informationNFPA 70E, Proposed Changes. Electrical Safety in the Workplace NFPA Conference & Expo
2017 NFPA Conference & Expo NFPA 70E, Electrical Safety in the Workplace Proposed Changes Presented by:: Paul Dobrowsky Innovative Technology Services Dave Dini Retired, Corporate Fellow Underwriters Laboratories
More informationSECTION 51 NFPA 70E POLICY. Health & Safety Policy and Procedures Manual
SECTION 51 NFPA 70E POLICY Health & Safety Policy and 1. Protection Against Arc Flash A. Policy: An arc flash is a dangerous condition associated with the release of energy caused by an electric arc. An
More informationPreparer: Owner: Approver: EHS Team Member TES Manager Site Manager
Procedure No.: BMEHS-002.033 Page: 1 of 10 Preparer: Owner: Approver: EHS Team Member TES Manager Site Manager Document Revision Change Table Revision Revision Description Revised Revision Number New By
More informationArc Flash. Safety 21
Arc Flash Safety 21 Arc Flash Introduction Electrical Hazards Safety Planning De-Energizing Equipment Working Hot Summary Introduction Most people don t think about electricity very much, which is surprising
More informationD Square Construction LLC
D Square Construction LLC Lock Out-Tag Out (LOTO) and Zero Voltage Verification (ZVV) Process and Plan Energized Work Process and Permit - 1 - Table of Contents 1) Instruction for using Decision Tree Analysis
More informationNFPA 70E Policies and Best Practices
NFPA 70E Policies and Best Practices Overview o Understand Compliance Requirements o Provide guidelines for a safe work environment o Effectively communicate policies to employees and customers o Express
More informationLeader s Guide ERI Safety Videos
1419 SAFE ELECTRICAL WORK PRACTICES & 2015 NFPA 70E Leader s Guide ERI Safety Videos SAFE ELECTRICAL WORK PRACTICES & 2015 NFPA 70E This easy-to-use Leader s Guide is provided to assist in conducting a
More informationElectrical Safety Program
Safety Manual Page 1 of 53 1. Purpose A. The purpose of the USPL (the Program ) is to provide a practical, safe working environment for USPL employees and contractors regarding the hazards arising from
More informationElectrical Safety Program
Electrical Safety Program For Adopted LC-1005 Rev. 06/16 Page 1 I. Introduction As part of Organization s overall safety and health program, an
More informationRecent changes in workplace safety regulations have heightened the awareness of hazards associated with electrical arcs.
Recent changes in workplace safety regulations have heightened the awareness of hazards associated with electrical arcs. The hazard level must be quantified and workers properly protected before entering
More informationMISSOURI UNIVERSITY OF SCIENCE & TECHNOLOGY Procedure: 3.6
Procedure This electrical safety procedure structures safety procedures to meet the requirements of the NFPA-70E Standard. The program is designed for qualified employees who occasionally must perform
More informationto the 2009 Edition Standards & Codes Introduction Background Byron Jordan Sr. Field Engineer
Critical Changes to the NFPA 70E Standard Standards & Codes Note 2 Byron Jordan Sr. Field Engineer Introduction Since its inception in 1979, NFPA 70E: Standards for Electrical Safety in the Workplace has
More informationMajor Changes. Standard. TECH TOPIC standards and. By Peter Walsh, PE
Major Changes to NFPA 70E Standard 2015 Edition TECH TOPIC standards and codes note 5 By Peter Walsh, PE Industrial Solutions Engineer Introduction NFPA 70E, Standard for Electrical Safety in the Workplace,
More information2018 NFPA 70E Significant Changes 7/27/2017. EFCOG Electrical Safety Task Group Workshop, July 2017
Significant Changes EFCOG Electrical Safety Task Group Workshop, July 2017 Appreciation Thanks to: Paul Dobrowsky creating the base PPT program Chair, Dave Dini for leading the Committee through the process
More informationUSA Mobile, AL Electrical Safe Working Practices
Compliance Compliance with these safe work practices is mandatory. Failure to comply may result in disciplinary action. These Safe Working Practices apply to any person performing electrical work at the
More informationElectrical Safety Work Practices
Work Practices I. SCOPE This program covers any SOUTHWESTERN COMMUNITY COLLEGE employee that may work or be exposed to exposed electrical systems: To assure that employees are not exposed to potentially
More informationOriginal Date of Issue: 04/09
POLICIES AND PROCEDURES DEPARTMENT: Environmental Health and Safety SUBJECT: Electrical Safety Program Original Date of Issue: 04/09 Reviewed 12/2011 Revised 12/2011 BACKGROUND ELECTRIC SHOCK It is well
More information2012 NFPA 70E: Electrical Safety In The Workplace
ERI Safety Videos Preventing Injuries Through Employee Training 2984 2012 NFPA 70E: Electrical Safety In The Workplace Leader s Guide ERI Safety Videos 2012 NFPA 70E: Electrical Safety In The Workplace
More information2. The purpose of this program is to achieve the following objectives:
Section 16A. Lockout and Tagout Program 1. In the course of their duties, personnel at the TFREC may need to secure controls, switches, and equipment in order to prevent injury caused by the sudden, unexpected
More informationElectrical Safety Program
Facilities Operations and Development Environmental Health and Safety 1314 Kinnear Road #106 Columbus, OH 43212-1168 614-292-1284 Phone 614-292-6404 Fax www.ehs.osu.edu Electrical Safety Program Prepared
More informationHealth & Safety Policy and Procedures Manual SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY
SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY 1. CONTROL OF HAZARDOUS ENERGY POLICY AND PROCEDURES A. OSHA References: 29 CFR 1910.147, 29 CFR 1910.332, 29 CFR 1910.333, 29 CFR 1926.417 B.
More informationRisk Assessment Procedure
Voltage, current testing, troubleshooting Infrared inspection Visual inspection, data collecting Risk Register ES Acc 6 4 1 1 6 36 ES < Acc 6 4 3 3 10 60 AF/AB 40 Acc 8 3 2
More informationELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR CFR , ,
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.331 335-29 CFR 1926.302, 1926.416, 1926.417 BASIS: The National Safety Council estimates that there are at least 300 deaths
More information70e Training - Electrical Safety in the Workplace
70e Training - Electrical Safety in the Workplace Contact us Today for a FREE quotation to deliver this course at your company?s location. https://www.electricityforum.com/onsite-training-rfq This NFPA
More informationCSA Z462 2 nd TO 3 rd EDITION DIFFERENCES CHANGES & UPDATES
CSA Z462 2 nd TO 3 rd EDITION DIFFERENCES CHANGES & UPDATES Provided to you by: Terry Becker, P.Eng., CESCP, IEEE Senior Member, Electrical Safety Expert CSA Z462 First Past Vice-Chair, Voting Member,
More informationThis is (Enter Company Name Here) Arc Flash Prevention policy. (Enter Name Here) will be responsible for overall direction of the Safety Program.
Company Name: Policy/Procedure ID Number: 222 Date: Grainger Safety Services Inc. 2012 Arc Flash Prevention Policy This is (Enter Company Name Here) Arc Flash Prevention policy. (Enter Name Here) will
More information2017 NWHA TECHNICAL SEMINAR. Arc Flash Hazard Awareness MIKE BRENDLE LLC
2017 NWHA TECHNICAL SEMINAR Arc Flash Hazard Awareness WHAT IS ARC FLASH Arc Flash is a short circuit that flashes from one exposed live part to another, or to ground The result is ionized air that creates
More information100 Questions on Electrical Safety Study Guide
100 Questions on Electrical Safety Study Guide Be advised that only 95 of 100 questions are presented here for the purpose of discouraging cheating on the final exam. 1. Why is electrical safety important?
More informationElectrical Safety Program
Electrical Safety Program Date of last revision: October, 2011-485 - Electrical Safety Program Update No updates. - 486 - Electrical Safety Program Update...486 (I) Purpose...488 (II) Policy...488 (III)
More informationLockout / Tagout Safety Program
Lockout / Tagout Safety Program Prepared by: The Ohio State University Environmental Health and Safety Occupational Safety & Industrial Hygiene 1314 Kinnear Road Columbus, OH 43212-1168 614-292-1284 Phone
More informationELECTRICAL SAFE WORK PRACTICES
STAFF ELECTRIC ELECTRICAL SAFE WORK PRACTICES PURPOSE The purpose of this procedure is to protect all workers from injuries resulting from exposure to arc flash, arc blast and electrical shock and to comply
More informationProgressive Safety Services LLC - All Rights Reserved
Estimated that 2,000 workers are treated in specialized burn centers each year as a result of arc flash (Electrical Safety Foundation International). According to the National Safety Council, medical costs
More informationEFCOG Best Practice # 206
EFCOG Best Practice # 206 Title: Adoption of NFPA 70E 2018 in place of NFPA 70E 2015 Facility: DOE Complex Points of Contact: John (Jackie) McAlhaney EFCOG ESTG Past Chair, jackie.mcalhaney@srs.gov, 803-557-9002
More informationSAFE-WORK PRACTICES Working On Or Near Energized Electrical Equipment CAT A-1 SOP #4
SUNCOR ENERGY PRODUCTS DISTRIBUTION TERMINAL OPERATING MANUAL STANDARD OPERATING PROCEDURE SAFE-WORK PRACTICES Working On Or Near Energized Electrical Equipment Lifesaving Rules Supporting Document Verify
More informationElectrical Safety Program February 2, 2016
Electrical Safety Program February 2, 2016 1. INTRODUCTION 1.1. Purpose Indiana University Environmental Health and Safety (IUEHS) has developed the Electrical Safety Program to protect employees from
More informationHazardous Energy Control
Lockout Tagout This program has been prepared to provide assistance in compliance with USA OSHA standards and/or Best Management Practices. It should not be used without consideration of the unique conditions
More informationSECTION 10 ELECTRICAL SAFETY
SECTION 10 ELECTRICAL SAFETY 10.1 Electrical Safety - Work Practices 10.2 Lockout / Tagout Procedure Revised: May 2012, March 2011 Updated: November 2017 Reviewed: November 2008 Revised: February 2003
More informationElectrical Safety Program
Environmental Safety Electrical Safety Program 50V-1000V The purpose of Clemson University s (CU) Electrical Safety Program is to protect all staff, students, and faculty from electrical hazards. Clemson
More informationUNIVERSITY OF TOLEDO
UNIVERSITY OF TOLEDO SUBJECT: CONTROL OF HAZARDOUS ENERGY SOURCES Procedure No: S-08-014 (LOCK-OUT / TAGOUT) AND ELECTRICAL SAFE WORK PRACTICES PROCEDURE STATEMENT This program applies to all employees
More informationAppendix A: Energized Work Permit
Appendix A: Energized Work Permit Part I: To be completed by the Supervisor Description of Circuit & Equipment: Job Location: Description of Work to Be Done: Justification of why the circuit cannot be
More informationDefinitions found in several locations:
Definitions found in several locations: NFPA 70 - National Electric Code NFPA 70B Recommended Practice for Electrical Equipment Maintenance. NFPA 70E Electrical Safety in the Workplace OSHA 1910 Subpart
More informationElectrical Safety Program
Electrical Safety Program The University Of Iowa Environmental Health & Safety 122 Grand Avenue Court Iowa City, IA 52242-1000 Phone: 319-335-8501 Date Revised/Reviewed: 6/8/2018 Table of Contents 1. Summary...
More informationWhy do I need to do an Arc-Flash Analysis?
Why do I need to do an Arc-Flash Analysis? Presented By Tom Norwood for Alexander Nizov, P.E. Principal/Manager Electrical Engineering Division TRAINING INSTITUTE, INC. A SUBSIDIARY OF MEGGER Hazards Analysis
More informationRemoving Yourself from Hazards During Equipment Operation
Removing Yourself from Hazards During Equipment Operation The safest way to work around electrical equipment is to turn it off. This is usually required by OSHA and NFPA 70E, but with some exceptions.
More informationElectrical Safety. Introduction
Electrical Safety 1 Introduction There are four main types of electrical injuries: Electrocution (death due to electrical shock) Electrical shock Burns Falls Around 300 workers were electrocuted in 2008
More informationWelcome to this training session about arc flash. In this session, we ll talk about the hazards and risks of working around exposed, energized
Welcome to this training session about arc flash. In this session, we ll talk about the hazards and risks of working around exposed, energized electrical equipment. We ll also discuss common arc flash
More informationCITY AND COUNTY OF DENVER CR&CF RISK UNIT Electrical Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.3 Electrical Safety Standard 1.0 Introduction 2.0 Scope The purpose of this standard is to establish safe work practices that are intended to prevent electric
More informationElectrical Safety Program
Electrical Safety Program 6300-3.1 Associated OHS Process: General Industry and Construction Safety The master copy of this document resides in electronic format. Printed copies of this document are for
More informationElectrical Hazard Assessments: OSHA & The NFPA 70E?
Electrical Hazard Assessments: OSHA & The NFPA 70E? AWEA Health & Safety Mike Moore Key Learning Objectives Key Learning's Statistical Electrical Incidents & Injuries What Does OSHA Want? A quick Glimpse
More informationLockout/Tagout Program
Lockout/Tagout Program Control of Hazardous Energy Subpart J - 29 CFR 1910.147 29 CFR 1926.417 OSHA Standard All industries must comply Estimated to prevent Approximately 120 fatalities per year 28,000
More informationHazardous Energy Control (Lockout-Tagout)
Hazardous Energy Control (Lockout-Tagout) The purpose of this program is to prevent inadvertent operation or energization of machines, equipment, or processes in order to protect employees and establish
More informationBest Practice #207. Facility: Entire DOE Complex. Best Practice Title: Identification of Look-Alike Electrical Equipment
Best Practice #207 Facility: Entire DOE Complex Best Practice Title: Identification of Look-Alike Electrical Equipment Point of Contact: Stephanie Collins, LBNL, SLCollins@lbl.gov, 510-486-4914; Mark Mathews,
More informationDuke University - Facilities Management Department Environmental Safety and Health Program ELECTRICAL SAFETY PROGRAM
ELECTRICAL SAFETY PROGRAM Applicable to: All FMD Organizations Date Effective: 7/1/2014 Issue No.: 1 Revision: 0 Page 1 of 9 A. Purpose 1. To establish a written electrical safety program that promotes
More informationSafe Schools: A Health and Safety Check
Name of School: Optional Information Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Use of Electrical Equipment Self-Inspection Checklist Guidelines: This checklist covers
More informationELECTRICAL SAFETY PROGRAM
0. INTRODUCTION 0.1 PURPOSE The purpose of this program is to provide a practical safe working area for employees relative to the hazards arising from the use of electricity. 0.2 SCOPE This program addresses
More informationPART Q CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT)
PART Q CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT) WAC Page 296-307-320 Control of hazardous energy (lockout-tagout). 1 296-307-32001 What does this section cover? 1 296-307-32003 When does this section
More informationPURE H2O FORUM. Safeguarding Operations Personnel Understanding Arc Flash & Developing an Electrical Safety Program
Shenandoah Valley Wastewater Treatment Plant Network PURE H2O FORUM Safeguarding Operations Personnel Understanding Arc Flash & Developing an Electrical Safety Program September 25, 2015 Presenter: Steve
More informationLockout/Tagout Program
Purpose Hazardous energy appears in the workplace in the form electrical, mechanical, pneumatic, hydraulic and thermal energy and includes chemical, water, steam and gaseous energy systems. Lockout/Tagout
More informationELECTRICAL SAFETY. Unsafe work practices near electricity can kill you! You are responsible for protecting yourself from electrical shock.
ELECTRICAL SAFETY Unsafe work practices near electricity can kill you! Electricity can cause: a mild shock, a severe shock, or even a deadly shock You are responsible for protecting yourself from electrical
More information2015 Revision to NFPA 70E & CSA Z462
2015 Revision to NFPA 70E & CSA Z462 The only thing that is constant is change. -- Heraclitus (500 BC) There are few universal truths in life: The sun will rise in the east every morning. There is nothing
More informationPage: 7/15/2009. Energy control procedures Use of lockout/tagout equipment to ensure safe work practices.
1 of 6 1.0 PURPOSE This program applies to the installation, service, maintenance, or removal of any type of machinery, equipment, or components, in which the unexpected start up or release of stored energy
More information11/2/2017. Course Objectives. Overview
Course Objectives The objective of this CBT module is to insure that personnel receive basic training in electrical safety. Every employee's work involves electricity. This may vary from typical electrical
More informationPAGE 1 OF 7 HEALTH, SAFETY & ENVIROMENTAL MANUAL PROCEDURE: S230 Lock-Out Tag-Out (LOTO) Program REV 4.0 8/13/2012
PAGE 1 OF 7 LOCK-OUT TAG-OUT (LOTO) THE CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM PURPOSE: 1. This standard establishes lockout/tagout (LOTO) procedures for the safety of personnel working on
More information: Electric Power Generation, Transmission, and Distribution. Region IV - OSHA
1910.269: Electric Power Generation, Transmission, and Distribution Region IV - OSHA Scope This standard covers the operation and maintenance of electric power generation, control, transformation transmission,
More informationLockout/Tagout - Energy Control Program
Lockout/Tagout - Energy Control Program Lockout and Tagging of ELECTRICAL Circuits This portion of the K.R. Miller Contractors, Inc. safety program has been created to maintain a written copy of procedures
More informationDepartment of Electrical Engineering & Computer Science. Electrical Safety. for Staff and Students in EECS Instructional Laboratories
NEVER WORK ALONE Department of Electrical Engineering & Computer Science Electrical Safety for Staff and Students in EECS Instructional Laboratories If you will be working with energized circuits or equipment
More informationSelection of Electrical PPE Tables
Selection of Electrical PPE Tables Instructions Table 1 - Starting with Table 1, select the task you plan to do (right-hand column) and the condition of the equipment you will be working on, (center column).
More informationArc Flash 101. presented by Arc Flash Blaster LLC
Arc Flash 101 presented by Arc Flash Blaster LLC ARC FLASH? ARC FLASH INCIDENT STANDARDS AND REGULATIONS Arc flash accidents... 35,000 F Molten Metal Pressure Waves Sound Waves Copper Vapour: (Solid to
More informationTitle: NFPA 70E Effective Date: 12/8/2014 Control Number: THG_0053 Revision Number: 1 Date: 10/26/2015 Annual Review Completed: 5/13/2015 NFPA 70E
Title: NFPA 70E Effective Date: 12/8/2014 Control Number: THG_0053 Revision Number: 1 Date: 10/26/2015 Annual Review Completed: 5/13/2015 CONTENTS NFPA 70E I. INTRODUCTION II. PURPOSE III. SCOPE IV. ENGINEERING
More informationEnvironmental, Health and Safety. Electrical Safety in the Workplace Program
Environmental, Health and Safety Electrical Safety in the Workplace Program September 2016 Table of Contents 1.0 Purpose... 1 2.0 Scope... 1 3.0 Definitions... 2 4.0 Responsibilities... 7 5.0 Requirements...
More informationANSWER SHEET NFPA 70E REVIEW 51. A B C D 76. A B C D 2. A B C D 77. A B C D 3. A B C D 52. A B C D 78. A B C D 4. A B C D 53.
AMERICAN ELECTRICAL INSTITUTE 2017 1 ANSWER SHEET NFPA 70E REVIEW First Name: Last Name: Date: Address: City: State: ZIP: License #: Phone: Email: ** See instructions on the inside cover page to submit
More informationElectrical Safety Guide
Electrical Safety Guide Helping Employers Protect Workers from Arc Flash and other Electrical Hazards meltric.com Why an Effective Safety Program is Essential The Hazards are Real Electrical Shocks National
More informationTHE UNIVERSITY OF NORTH CAROLINA
THE UNIVERSITY OF NORTH CAROLINA AT CHAPEL HILL CHILLED WATER DEPARTMENT ENERGY CONTROL PROCEDURE The purpose of this document is to establish minimum requirements for the manual isolation and securing
More informationWhat Every Town Manager Needs to Know About Workplace Safety
What Every Town Manager Needs to Know About Workplace Safety Presented to: Massachusetts Municipal Association Annual Meeting & Trade Show January 23, 2016 Mary Dozois, CIH Department of Labor Standards
More information2018 NFPA 70E Electrical Safe work practices
This course provides a thorough knowledge of the dangers and recommended safe behaviors for those who work daily around electrical hazards. This course goes into examples of real life application to give
More informationElectrical. OSHA Office of Training and Education 1
Electrical OSHA Office of Training and Education 1 Introduction An average of one worker is electrocuted on the job every day There are four main types of electrical injuries: Electrocution (death due
More informationIWU PHYSICAL PLANT SAFETY PROGRAM. Revision: 1 ELECTRICAL SAFETY Section: 4
STANDARDS Title 29 Code of Federal Regulations (CFR) Part 1910 Subpart S 301-399; NFPA 70E 2012 1.0 INTRODUCTION Electricity is a serious workplace hazard, capable of causing both employee injury and property
More information2. What is the definition of an electrocution hazard? a. Electrocution results when a person is exposed to a lethal amount of electrical energy
Electrocution Hazards Lesson Plan Sample Lesson Plan In This Document Construction Training Program (10-hour) Overview The purpose of this lesson is to provide workers with information that will enable
More informationBy: Bruce Bowman, P.E.
Welcome to The NFPA 70E Electrical Safety Presentation Updated for 2012 www.nfpa.org By: Bruce Bowman, P.E. What is the best way to prevent the hazards of electricity? Stop Think Options Protection - Before
More informationCONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM
CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM 1.0 REGULATORY AUTHORITY Code of Federal Regulations, 29 CFR 1910.147; California Code of Regulations, Title 8, Sections 2320.1 and 3314; CSU, Fullerton
More informationLO/TO LOCKOUT/TAGOUT PROGRAM
LO/TO LOCKOUT/TAGOUT PROGRAM April 2017 CONTENTS Section 1: Introduction...1 Section 2: Purpose... 1 Section 3: Application... 1 Section 4: Definitions... 2 Section 5: Roles and Responsibilities... 4 Section
More informationPOWER PLANT RELAY REPLACEMENT DELIVERABLE ARC FLASH
POWER PLANT RELAY REPLACEMENT DELIVERABLE ARC FLASH ISU Senior Design Group: Dec15-22 Dan Dye Project Web Site: http://dec1522.sd.ece.iastate.edu/ Project Sponsor: CIPCO Project Advisor: Professor Mani
More informationThe Pennsylvania State University Energized Electrical Safety Program
Introduction: The Pennsylvania State University Energized Electrical Safety Program Purpose: Electricity is a serious workplace hazard, capable of causing both employee injury and property damage. It is
More information1 of 3 5/5/2014 2:20 PM NFPA STANDARDS DEVELOPMENT SITE FIRST DRAFT REPORT Closing Date: March 05, 2013 Welcome Kimberly Shea! NFPA 70E, Standard for Electrical Safety in the Workplace, 2012 Edition NOTE:
More informationSAINT MARY S COLLEGE OF CALIFORNIA STANDARD HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT. Prepared by
SAINT MARY S COLLEGE OF CALIFORNIA STANDARD 1.1.4 HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT Prepared by SAINT MARY S COLLEGE OF CA MORAGA, California KAREN LAURICELLA Original Date: 1 JULY
More informationGround Fault Circuit Interrupter(GFCI) Policy
NewStar Netronics, LLC American Products for the World Ground Fault Circuit Interrupter(GFCI) Policy 3926 East 3 rd Street Tulsa, OK 74112 Phone (918)894-5006 Fax (918)836-9909 tech@newstarnetronics.com
More informationLockout/Tagout Plan Environmental Health & Safety Office July 2017
July 2017 Table of Contents Acronyms... iii Foreword... iv Document History... iv 1.0 Introduction... 1 1.1 Purpose... 1 1.2 Scope... 1 1.3 Lockout/Tagout Program... 1 2.0 Roles and Responsibilities...
More informationELECTRICAL SAFETY PROCEDURE
ELECTRICAL SAFETY PROCEDURE 1 Table of Contents 1 PURPOSE... 3 2 PROGRAM COMPLIANCE... 3 3 SCOPE... 3 4 DEFINITIONS... 3 5 RESPONSIBILITES... 3 6 ELECTRICA HAZARDS... 4 7 TRAINING... 4 8 PORTABLE ELECTRICAL
More informationWHAT IS THE N.F.P.A. 70E
WHAT IS THE N.F.P.A. 70E N.F.P.A. 70E Standard for Electrical Safety in the Workplaces HAZARDS of ELECTRICITY FIRE-Faulty wiring-building fires. Clothing fires(arc flash). SHOCK-When electrical current
More informationAdvances in Low Voltage Motor Control Center (MCC) Technology Help Reduce Arc-Flash Hazards and Minimize Risks
Advances in Low Voltage Motor Control Center (MCC) Technology Help Reduce Arc-Flash Hazards and Minimize Risks Selecting the right MCC equipment leads to improved plant safety, helping protect people and
More informationLock Out/Tag Out Control of Hazardous Energy
Lock Out/Tag Out Control of Hazardous Energy University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells 1.0 Program Objective UF
More informationHIGH-IMPACT SAFETY TRAINING FOR QUALIFIED ELECTRICAL WORKERS
HIGH-IMPACT SAFETY TRAINING FOR QUALIFIED ELECTRICAL WORKERS This easy-to-use Leaders Guide is provided to assist in conducting a successful presentation. Featured are: INTRODUCTION: A brief description
More informationKMU SUBSTATION WORKSHOP
Rick Aguilar, Director of Job Training & Safety KMU SUBSTATION WORKSHOP JUNE 29-30, 2016 OTTAWA, KS Hazards & Safety Rules Qualified Personnel & Task-Based Hazard Mitigation Worksite Applications & Considerations
More informationLOCKOUT / TAGOUT PROGRAM
LOCKOUT / TAGOUT PROGRAM Developed in accordance with the OSHA Control of Hazardous Energy Standard, 29 CFR 1910.147 DECEMBER 7, 2017 SKIDMORE COLLEGE 815 NORTH BROADWAY, SARATOGA SPRINGS, NY 12866 Table
More informationLOCKOUT/TAGOUT PROGRAM
0 Appendix C OCCUPATIONAL SAFETY AND HEALTH PROGRAM LOCKOUT/TAGOUT PROGRAM Hazardous Energy Control Lockout/Tagout Program TABLE OF CONTENTS Section Page I. Purpose and Scope. 1 II. Definitions 1 III.
More information