Under Basin Storage Unit

Size: px

Start display at page:

Download "Under Basin Storage Unit"

Avis Blair
5 years ago
Views:

1 Under Basin Storage Unit Assembly Instructions- please keep for future reference ML235 Dimensions Width - 48cm Depth - 30cm Height - 60cm Important Please read these instructions fully before starting assembly

2 Safety and Care Advice Important Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages 1 and 2. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Care and maintenance Only clean using a damp cloth and mild detergent, do not use bleach or abrasive cleaners. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possible. Assemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with 2 people. From time to time check that there are no loose screws on this unit. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Dispose of all packaging carefully and responsibly. This product should not be discarded with household waste. Take to your local authority waste disposal centre.

3 Components - Panels Please check you have all the panels listed below 1 Top x 1 2 Left side x 1 3 Right side x 1 (48(w)cm x 30(d)cm) (49(h)cm x 28.5(d)cm) (49(h)cm x 28.5(d)cm) 4 Base x 1 5 Left door x 1 6 Right door x 1 (48(w)cm x 28.5(d)cm) (50.5(h)cm x 24(w)cm) (50.5(h)cm x 24(w)cm) 7 Back panel x 2 (51.5(h)cm x 12(w)cm) 8 Shelf x 1 (45w(h)cm x 28(d)cm) 1

4 Components - Fittings Note: may be supplied than are required. A B C D Foot x 4 14mm Screw x 18 12mm Screw x 16 Magnetic catch x 1 E F G H Hinge x 4 16mm Screw x 4 Catch plate x 2 35mm Male camlock x 8 I J K L Female camlock x 8 Handle x 2 Shelf bracket x 4 Back panel screw x 10 M 10mm Screw x 2 Tools required Phillips screwdriver (medium & large) Ruler Use this ruler to help correctly identify the screws

6 Step 1 Screw 4 x 35mm male camlock H into underside of top 1 as Fix magnetic catch D to underside of top 1 using 2 x 14mm screw B as shown (a:). 1 H a: D B Step 2 4 Fix 4 x foot A to underside of base 4 using 16 x 14mm screw B as shown (b:). b: A B 3

7 Step 3 Screw Turn base 2 x male 4 over camlock and insert A into 4 reverse x 35mm of male drawer front camlock 13 as H as H 4 Step 4 Connect hinges B to top door 5 and bottom door 6 using 15mm screws F as Step 4 Insert 4 x female camlock I into left side 2 and right side 3 as 2 3 I Step 5 Insert 4 x 15mm female camlock E into under side of top base 7 as Insert 4 x small wooden dowel D into top shelf 9 as 4

8 Step 65 Connect top left side base 27 to and base top 4 shelf as 9 to top right side 2. Tighten the female Tighten camlocks female with a camlocks in screwdriver. under side of top base 7 with a screwdriver. Note: you should feel a click when the female camlocks are fully locked. 2 Step 7 4 Connect top left side 1 to exposed ends of top base 7 and top shelf 9 as shown Tighten female camlocks in under side of top base 7 with a screwdriver. Step 6 Connect right side 3 to Step 8 base 4 as Screw Tighten 4 the x male female camlock A camlocks into the with under a side of top screwdriver. 10 as Note: you should feel a click when the female camlocks are fully locked. Step 9 Connect top 10 as Tighten female camlocks with a screwdriver

9 Step 7 Connect top 1 to left side 2 and right side 3 as Tighten the female camlocks with a screwdriver. Note: you should feel a click when the female camlocks are fully locked C Step 8 Connect left door 5 to left side 2 using 2 x hinge E and 4 x 14mm screw C as shown (c:). G M c: E Fix 1 x catch plate G to inside of door using 1 x 10mm screw M as Connect 1 x handle J to door using 2 x 16mm screw F as J 5 2 F 6

10 Step 9 M Connect right door 6 to right side 3 using 2 x hinge E and 4 x 14mm screw C as shown (refer to detail diagram c: in Step 8). G Fix 1 x catch plate G to inside of door using 1 x 10mm screw M as Connect 1 x handle J to door using 2 x 16mm screw F as 3 6 J F Step 10 Fix 2 x back panel 7 to rear of unit using 10 x back panel screw L as 7 L 7 7

11 Step 11 Insert 4 x shelf bracket K into holes inside the unit at the desired height. Set shelf 8 onto shelf brackets. Assembly complete. K 8 8

BASIC TALLBOY MIRROR CABINET

BASIC TALLBOY MIRROR CABINET 402/9166 30cm 28cm 180cm Issue 1-30/03/15 Safety and Care Advice Important Please read these instructions fully before starting assembly Check you have all the components and