The M-UPPT is an universal punch tool. Different punch inserts can be easily switched out. Pin to fix and remove inserts

Size: px

Start display at page:

Download "The M-UPPT is an universal punch tool. Different punch inserts can be easily switched out. Pin to fix and remove inserts"

Isaac Riley
5 years ago
Views:

2 The is an universal punch tool. Different punch inserts can be easily switched out. Pin to fix and remove inserts To install a punch insert, slide in the punch insert and fix this insert with the pin on the front side. 15 januari 2013, _UserManual Page 2 of 16

3 M-PLC20-01 This punch insert can be used for making a square hole into the head rail. This hole can be used for assembly of the control unit, the end caps and the cord spools. Install punch insert into the frame Separate stopper for punching the first hole. Can be used at both sides. 15 januari 2013, _UserManual Page 3 of 16

4 Slide in head rail with the flat side on the front. Flat side of head rail should be on this side 15 januari 2013, _UserManual Page 4 of 16

on the right side of the punch Push rail against stopper and

5 Punch the first hole (for assembly of control unit or end cap) by using the separate stopper Click in separate stopper on the right side of the punch Push rail against stopper and punch first hole 15 januari 2013, _UserManual Page 5 of 16

Punch 2 nd hole For control unit side, use first plate of stopper For

First set the stopper on the given pitch dimension by the

Set pitch distance according calculationsheet.

6 Punch 2 nd hole For control unit side, use first plate of stopper For end cap side, use second plate of stopper Punch intermediate holes. First set the stopper on the given pitch dimension by the calculationsheet. Punch the required number of intermediate holes. Set pitch distance according calculationsheet. Value should be set read from the left side of the stopper 15 januari 2013, _UserManual Page 6 of 16

Punch last 2 holes on the same way as the 2 first holes.

For end cap side, use second plate of stopper For control unit

assembly of control unit or end cap) by using the separate

7 Punch last 2 holes on the same way as the 2 first holes. First punch the last hole for the cord spool. For end cap side, use second plate of stopper For control unit side, use first plate of stopper Punch the first hole (for assembly of control unit or end cap) by using the separate stopper Push rail against stopper and punch first hole 15 januari 2013, _UserManual Page 7 of 16

8 M-PLC20-02 This punch insert can be used for making a Ø5mm hole into the PVC strip PLC20-04 or the aluminium profile PLC This hole can be used for the cord holes in the PVC strip (used in all systems) or for making a top-down/bottom-up system Hole for insert PVC strip Hole for insert aluminium profile 15 januari 2013, _UserManual Page 8 of 16

Punching the PVC strip PLC20-04 Always punch the first hole on the right side by placing the strip against the 2 nd plate of the stopper on the right side of the punch.

9 Punching the PVC strip PLC20-04 Always punch the first hole on the right side by placing the strip against the 2 nd plate of the stopper on the right side of the punch. Place the strip on the small square plate of the stopper. (the first and last hole are always on this same fixed distance of 74mm from the side) Place strip against this square part of the stopper 15 januari 2013, _UserManual Page 9 of 16

Value should be set read from the left side of the stopper Punch the last hole on the left side

10 Set the pitch distance according the calaculationsheet and punch the required number of holes except the last one. Set pitch distance according calculationsheet. Value should be set read from the left side of the stopper Punch the last hole on the left side on the same way as the first one, only now at the left side of the punch. 15 januari 2013, _UserManual Page 10 of 16

11 Punching the aluminium profile PLC20-01 (only for Top-Down/Bottom-up systems) Punching of this holes works exact on the same way as punching the PVC strip. First punch the first hole by placing the profile against the right stopper. Than punch the required number of holes by using the pitch distance stopper. 15 januari 2013, _UserManual Page 11 of 16

12 And finally punch the last hole by using the stopper on the right side 15 januari 2013, _UserManual Page 12 of 16

13 M-PLC20-03 This punch insert can be used for making a U-shape cut-out into the aluminium profile. This cut-out can be used for assembly of the end cap. 15 januari 2013, _UserManual Page 13 of 16

14 To punch the profile, place the profile with the top side pointing down. Push the profile fully into the punch insert. 15 januari 2013, _UserManual Page 14 of 16

15 M-PLC20-04 This punch insert can be used for making 3 holes into the aluminium profile. This hole can be used for assembly of the grip handle for tensioned systems. 15 januari 2013, _UserManual Page 15 of 16

16 First set the stopper on the right dimension which is given by the calculationsheet. Than place the profile against the stopper and punch the holes. Set distance according calculationsheet. Value should be set read from the left side of the stopper 15 januari 2013, _UserManual Page 16 of 16

M*CARBO Hi-Point Carbine Trigger Spring Kit Download or Print Instructions Contact: Page 1

M*CARBO Hi-Point Carbine Trigger Spring Kit Download or Print Instructions Contact: Page 1 Download or Print Instructions Contact: help@mcarbo.com Page 1 Step 1: Clear your Firearm - Check the chamber, bolt face and magazine well. Step 3: Using the Hi-Point disassembly tool break the bolt loose