Job Sheet 12. Feeding Conductors into Conduit OBJECTIVE PROCEDURE
|
|
- Jason Parks
- 5 years ago
- Views:
Transcription
1 Job Sheet 12 Feeding Conductors into Conduit OBJECTIVE To feed several conductors of type XHHW and size 14 AWG at the same time into 3/4" electrical metallic tubing (EMT). PROCEDURE 1. Perform the basic safety procedures listed in Appendix C of this manual. 2. Read reference 8 (see Appendix E) for more information on installing conductors in conduit systems. 3. Figure 66 shows a fish tape made of flexible steel. Figure 66. A fish tape made of flexible steel. Festo Didactic
2 4. Figure 67 shows wire grips (basket grip type) of two different sizes. Figure 67. Wire grips (basket grip type) of two different sizes. 5. Move the dummy enclosures installed on the Mobile Workstation to the positions shown in Figure Festo Didactic
3 ¾" EMT Clamps Clamps Coupling 10 ½" 1" offset 32 ½" Clamps 8¾" 1" offset ¾" EMT Figure 68. Dummy enclosures interconnected with 3/4" EMT. 6. Take a 5' long piece of 3/4" EMT to fabricate section 1 shown in Figure The distance between the lower dummy enclosure and the back of the bend is 19". To calculate the location of the bending mark for the 90 bend: Mark for 90 = 19" - TAKE-UP + SHRINK where TAKE-UP is 6" for the 3/4" EMT bender SHRINK is 1/16" due to the 1" deep, 10 offset Mark for 90 = 19" - 6" + 3/8" = 13 1/16" Draw a mark at 13 1/16" from the end of the conduit. 8. Insert the conduit in the bender shoe and align the arrow with the bending mark. Do NOT bend the conduit now. Festo Didactic
4 9. Draw a mark on the conduit at the end of the bender shoe. The 10 offset will have to be made between this mark and the end of the conduit. This is done to make sure the bender will not interfere with the offset while making the 90 bend. 10. The length available to make the 10 offset is approximately 11 3/16" between the end of the conduit and the end of the bender for the 90 bend. The distance between the two bending marks is 6" for a 1" deep, 10 offset. To center the offset, the first bending mark is located at 2 19/32" from the end of the conduit and the second bending mark is located at 2 19/32" + 6" = 8 19/32". Draw a mark at 2 19/32" and another one at 8 19/32" from the end of the conduit. 11. Make the two bends of the 10 offset first. Refer to Job Sheets 5 and 6 for the bending procedure. 12. Make the 90 bend. Refer to Job Sheet 7 for the bending procedure. Make sure you bend it so that the end of the offset is in-line with the opening in the lower dummy box. 13. The location of the bending marks for section 2 are the same as for section 1, except for the second 90 bend. Make sure you align the tip of the star with the mark for the second 90 bend. 14. Make the 10 offset bends first and then the two Interconnect the two dummy enclosures installed on the Mobile Workstation as shown in Figure 68. Notice that two EMT-to-EMT couplings and a small piece of conduit approximately 3 3/4" long are used to join the two sections of EMT that interconnect the dummy enclosures. Also notice that clamps, as the one shown in Figure 69, are used to securely fasten the EMT to the metal struts installed on the Mobile Workstation. 58 Festo Didactic
5 Figure 69. Clamp used to securely fasten EMT to metal struts. 16. Install 10 conductors of type XHHW and size 14 AWG in the 3/4" EMT that interconnects the two dummy enclosures. To do so: Gather 10 conductors and cut them so that there length is approximately one foot longer than the total length of sections 1 and 2. Tape the ends together to avoid unraveling during assembly as shown in Figure 70. Figure 70. Tape the ends of the conductors to avoid unraveling. Take the 3/4" wire grip and insert the conductors up to the bend in the shoulder protector. Festo Didactic
6 All slack should be ironed out of the mesh starting at the shoulder protector and working back toward the tail as shown in Figure 71. Push here Pull here Figure 71. Eliminate the slack. Lubricate the shoulder protector with wire lubrication compound as shown in Figure 72. Lubrication is used to help pull conductors through conduits. Figure 72. Wire lubrication compound applied to a wire grip. 60 Festo Didactic
7 Insert the hook of the fish tape at one end of the conduit and push it until it comes out as shown in Figure 73. Figure 73. Feed the fish tape into the conduit. Festo Didactic
8 Attach a pull line to the hook of the fish tape and pull the fish tape out of the conduits until the pull line comes out on the other side as shown in Figure 74. Figure 74. Feed the pull line into the conduit. 62 Festo Didactic
9 Attach the wire grip to the pull line, insert the wire grip into the conduit and pull the pull line until the wire grip comes completely out of the conduit as shown in Figure 75. Figure 75. Feed the wire grip into the conduit. Remove the conductors from the wire grip. 17. Ask the instructor to check and approve your work. 18. Remove the conductors that you installed in the conduit. Remove the upper section of 3/4" EMT that interconnects the dummy enclosures. Keep the rest of the setup, it will be used in the next job sheet. Name: Date: Instructor's approval: Festo Didactic
Wing assemblyfinal Master 4/29/04 11:20 PM Page 1. Issued January 1, Sabre Aircraft. Assembly Manual. Sabre 16ss Wing
Wing assemblyfinal Master 4/29/04 11:20 PM Page 1 Issued January 1, 2002 Sabre Aircraft Assembly Manual Sabre 16ss Wing Wing assemblyfinal Master 4/29/04 11:20 PM Page 2 1. 2. 1. Unzip the cover and remove
More informationFeatures. Instructions. Your IDEAL Bender has engineered features which include:
Bender Guide Features Your IDEAL Bender has engineered features which include: 1. Arrow To be used with stub, offset and outer marks of saddle bends. 2. Rim Notch Locates the center of a saddle bend. 3.
More informationHANGERS & SUPPORTS CLIP-IT CLIP-IT STUD STRAPS BAR JOIST CLIP CONDUIT HANGERS CLIP-IT
62 hangers & supports Innovation. It s what Madison is all about. Check out our Madison Strap, the product that started it all. Invented in 1929 by our founder Earl Adkinson, Madison has been on the cutting
More informationWork Standard CABLE PULLING OPERATIONS
Page 1 of 19 ****This document supercedes BECo WMS 2.9-1.1**** 1.0 Purpose CABLE PULLING OPERATIONS 1.1 This Work Method Standard prescribes the preferred methods of removing and installing cables between
More informationOPERATING and MAINTENANCE INSTRUCTIONS MAXIS Grips
OPERATING and MAINTENANCE INSTRUCTIONS MAXIS Grips (GP110/GP00AA/GP101A /GP102B/GP103C/GP104D) 04/17 GP110/GP00AA/GP101A/GP102B/GP103C/GP104D Manual READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY
More informationInstructions. Follow All Instructions Before Assembling Or Using This Product
Instructions Follow All Instructions Before Assembling Or Using This Product IMPORTANT DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 WARNING: Improper use
More informationINSTRUCTION MANUAL. January 23, 2003, Revision 0
INSTRUCTION MANUAL Model 810A In-Vitro Test Apparatus for 310B Muscle Lever January 23, 2003, Revision 0 Copyright 2003 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Parkway S., Unit 4 Aurora,
More informationShimano Di2 Installation on S5
Installing Shimano Dura Ace Di2 Shifting Systems Note these instructions and pictures are for assembling the Shimano Dura Ace Di2 system (Internal Spec) on the Cervélo S5 frame. The Shimano Ultegra Di2
More informationROAD DISC TECHNICAL MANUAL
ROAD DISC TECHNICAL MANUAL INTRODUCTION Congratulations on purchasing a Felt disc brake equipped road bike. As with all of our bikes and components, our aim is to provide the rider with the best product
More informationTECHNICAL HANDBOOK nvent CADDY Speed Link Manual. SLS Locking Device
TECHNICAL HANDBOOK nvent CADDY Speed Link Manual SLS Locking Device Contents 1. WIRE ROPE SUPPORT OVERVIEW 3 A. Using Wire Rope 3 B. The nvent CADDY Speed Link Manual 3 C. SLS Features 4 D. SLS Mechanism
More informationSpring steel fasteners KWHS-14R. KwikWire. Hanging system
Spring steel fasteners KWHS-14R KwikWire Hanging system KwikWire Hanging System Takes the strain out of hanging with chain The KwikWire Hanging System is a flexible replacement for jack chain and all thread
More informationB-LINE SERIES. Spring steel fasteners KWHS-15. KwikWire. Hanging system
Spring steel fasteners KWHS-5 B-LINE SERIES KwikWire Hanging system KwikWire hanging system. Takes the strain out of hanging with chain Application Photos Applications for the KwikWire Hanging System include:
More informationPOWER TOOL ACCESSORIES MADE FOR THE TRADE! KNOCKOUTS BENDING. Voltage Detector, Non-Contact GT-12A V with Audible Alarm and Bright LED s
TESTING POWER TOOL ACCESSORIES KNOCKOUTS Voltage Detector, Non-Contact GT-12A 50-1000V with Audible Alarm and Bright LED s 34401 34403 34411 36414 BENDING 555 Classic Electric Bender 555C Bender Only 555RSC
More informationAMTEC SUPPORT GRIPS STANDARD, HEAVY DUTY & CONDUIT GRIPS
AMTEC SUPPORT GRIPS STANDARD, HEAVY DUTY & CONDUIT GRIPS DESIGNED TO HOLD THE WEIGHT FOR ELECTRICAL CABLE AS IT HANGS IN VERTICAL, SLOPING OR HORIZONTAL POSITIONS. EASILY INSTALLED AND REMOVED USING NO
More informationTECHNICAL HANDBOOK. nvent CADDY Speed Link Manual Overview of Wire Rope Hanging
TECHNICAL HANDBOOK nvent CADDY Speed Link Manual Overview of Wire Rope Hanging Contents 1. WIRE ROPE SUPPORT OVERVIEW...3 A. Using Wire Rope...3 B. The nvent CADDY Speed Link Manual...3 2. OVERVIEW OF
More informationGel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions
Gel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions TECP-30-215 Issue 1 4/2013 INTRODUCTION The Gel Drop Seal device is for use with FOSC 450 B, B Short, C, and D size closures
More informationExercise 5-2. Bubblers EXERCISE OBJECTIVE DISCUSSION OUTLINE. Bubblers DISCUSSION. Learn to measure the level in a vessel using a bubbler.
Exercise 5-2 Bubblers EXERCISE OBJECTIVE Learn to measure the level in a vessel using a bubbler. DISCUSSION OUTLINE The Discussion of this exercise covers the following points: Bubblers How to measure
More informationBENDING CONDUIT / TUBING USING HAND BENDERS
www.learnnec.net 408-866 - 7890 Electrical Code training and consultation based on NEC 2008 BENDING CONDUIT / TUBING USING HAND BENDERS The ability to bend conduit and tubing is a requirement for all electricians.
More informationCADDY SPEED LINK MANUAL SLK LOCKING DEVICE
CADDY SPEED LINK MANUAL SLK LOCKING DEVICE CONTENTS 1. Wire Rope Support Overview...3 A. Using Wire Rope...3 B. The CADDY SPEED LINK Manual...3 C. SLK Features...4 D. SLK Mechanism...5 2. Typical CADDY
More informationTOWER INSTALLATION MANUAL For A.R.E. Guyed Pipe Towers Short Towers 43, 64 and 85 feet tall
TOWER INSTALLATION MANUAL For A.R.E. Guyed Pipe Towers Short Towers 43, 64 and 85 feet tall Contents 1) Introduction...2 2) Site Selection and Preparation...2 3) Tools List...3 4) Parts List...4 5) Tower
More informationTypical Strength of Glued Connection. Typical Strength of Screwed Connection
Rodder Introduction DCD offers one of the most comprehensive range of Rodders available anywhere in the world - from the smallest 1/8 dia. Fish Tapes to the rugged 1/2 Rodders. The Rod DCD rods are manufactured
More informationCheck with local zoning official for property line distance requirements.
RESIDENTIAL POOL PLAN SUBMITTAL GUIDELINES The following guidelines are intended to assist municipal residents with the permit acquisition process with regard to pools, spas and hot tubs for single family
More informationHOME ASSEMBLY INSTRUCTIONS
HOME ASSEMBLY INSTRUCTIONS This Papillionaire Bicycle now belongs to you. It will take you to work, wait patiently outside your local cafe, and carry your groceries home. This is the start of your long-term
More informationBulletin Swimming pool, hot tub and spa installations Rules , , , , , and
Bulletin 68-7-11 Swimming pool, hot tub and spa installations Rules 68-000, 68-056, 68-058, 68-064, 68-068, 68-302 and 68-404 Scope (1) Swimming pools - general (2) Grounding & bonding (a) Bonding for
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationAppendix 4 Don t Get Hurt Pulling Cable
Appendix 4 Don t Get Hurt Pulling Cable Appendix 4 Don t Get Hurt Pulling Cable Don t Get Hurt Pulling Cable Here are some tips on pulling cable safely (Reprinted from CEE News dated June, 1990) There
More information854DX Electric Bender
INSTRUCTION MANUAL 854DX Electric Bender Patents Pending Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product
More informationLadies Shopper Bike Assembly Manual 28C03
Ladies Shopper Bike Assembly Manual 28C03 Ecosmo Ltd 1 Know your bike 1. Wheel 2. Rear Derailleur 3. Chain 4. Crank Set 5. Pedal 6. Seat Quick Lock 7. Saddle and Post 8. Frame 9. Front Light 10. Front
More informationInstallation Guideline for Placing Fiber Optic Cable into an Underground Duct
Installation Guideline for Placing Fiber Optic Cable into an Underground Duct Table of Contents A. Purpose... 1 B. Introduction...2 C. General Precautions...2 D. Reference Documents...3 E. Fiber Optic
More informationStep 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.
WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the
More informationwill not support combustion
Strain Relief Grips Operating Temperatures Material Temperature Range Aluminum 40 C to +149 C ( 40 F to +300 F) Aluminum deluxe cord grips 34 C to +115 C ( 30 F to +240 F) Non-metallic deluxe cord grips
More informationTECHNICAL BULLETIN PINPOINT CONDUIT COUPLING AND SPLICING RECOMMENDATIONS
TECHNICAL BULLETIN PINPOINT CONDUIT COUPLING AND SPLICING RECOMMENDATIONS CONTENTS: 1.0 General Information 2.0 Preparation and Splicing of PinPoint Wire 3.0 PinPoint Direct Bury Splice Kit Specifications
More informationIMPORTANT: RECEIVING INSTRUCTIONS:
Instruction Sheet Sidewinder Mechanical Bender IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once.shipping damage
More informationPolatrak ROV II - Tip Contact Probe Operation Manual
This PDF document contains Live Web Links Click them for more information from the web Polatrak ROV II - Tip Contact Probe Operation Manual A Cathodic Protection Probe with dual Ag/AgCl reference cells
More informationAH-03: Bend Tubing. SAFETY FIRST o Follow all Caterpillar facility safety standards when performing this task.
AH-03: Bend Tubing Page 1 of 23 SAFETY FIRST o Follow all Caterpillar facility safety standards when performing this task. EQUIPMENT o tube benders, various sizes o levels o tube cutter, various sizes
More informationWalking & Patient Room Aids
Walking & Patient Room Aids Product Description, Features & 34 Futurity Gate, Unit # 15 Concord Ontario L4K 1S6 wk: 416-739-1267 Toll Free: 1-888-634-5808 fx 416-739-7171 email: info@hpurehab.com www.hpurehab.com
More information855GX IntelliBender Electric Bender
INSTRUCTION MANUAL 855GX IntelliBender Electric Bender Patents Pending Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register
More informationSECTION 2 RING MOUNT
SECTION 2 RING MOUNT Rotax aircraft engines are manufactured and supported by Rotax GmbH of Austria. Read and understand the Rotax manuals completely before starting with the engine installation, as they
More informationUNITY 2. Uni-DAAMS Manual. Version 1.3 (Changes to Section 1.1) March 2010
UNITY 2 Uni-DAAMS Manual Version 1.3 (Changes to Section 1.1) March 2010 1. Introduction...2 1.1. Installing the DAAMS tube ovens...2 1.2. Swapping between tube types...5 1.3. Changing tube oven o-rings...6
More informationUser Manual Important, read before use!
EN User Manual Important, read before use! SMART Congratulations on your new rollator! Volaris Smart The Volaris Smart will make your life easier in many ways. We ask you to read carefully through this
More informationUses, Certifications, and Standards FASTENERS,KWIK WIRE,Lighting, Ductwork, Cable Tray
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 BKP10094 SPRG Wire Rope/CLMP Kit Cooper B-Line/Cable Tray Manufacturer Description Weight per unit Product Category Features
More informationPULLTARP INSTALLATION & OPERATORS MANUAL
PULLTARP INSTALLATION & OPERATORS MANUAL Step 1. Mounting Positions Determine the mounting position for your truck Fig. 1 - Fig. 7. Fig. 1 Fig. 2 Fig. 3 A Mount Top Or Bottom Roll B Mount Top Or Bottom
More informationInstructions. Follow All Instructions Before Assembling Or Using This Product
Instructions Follow All Instructions Before Assembling Or Using This Product IMPORTANT DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 WARNING: Improper use
More informationDetailed Instructions for the use of Wirelock
Detailed Instructions for the use of Wirelock With Strand or General Purpose Wire Rope These instructions explain the proper use of WIRELOCK for socketing wire rope terminations. When reading and following
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationIMPORTANT WARNING SOUL PAD (2X) PAD STRAP (4X) S.U.P. BRAH (1X) KEYS (2X) RIPCORD (2X) HOOK (2X) NOSE/TAIL STRAP (2X)
SOUL PAD (2X) PAD STRAP (4X) S.U.P. BRAH (1X) KEYS (2X) HOOK (2X) RIPCORD (2X) NOSE/TAIL STRAP (2X) IMPORTANT WARNING IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED
More informationINSTALLATION, OPERATION AND MAINTENANCE GUIDE
INSTALLATION, OPERATION AND Placement in Pipeline System When installing Process Development & Control s ElastoTITE Elastomer-Hinged Check Valves in a pipeline, a minimum of five pipe diameters should
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Ballpark Classics Baseball Game MLB Edition Figure B Read the instructions completely before beginning g assembly. You will need a Phillips screwdriver. 1. Remove the game from the
More informationShifting Lever. RAPIDFIRE Plus 11-speed
(English) DM-SL0005-04 Shifting Lever Dealer's Manual RAPIDFIRE Plus 11-speed MTB XTR SL-M9000 DEORE XT SL-M8000 CONTENTS IMPORTANT NOTICE... 3 TO ENSURE SAFETY... 4 LIST OF TOOLS TO BE USED... 7 INSTALLATION...
More informationSamurai Armor Set: Step by Step
Samurai Armor Set: Step by Step Pack 3 Stages 9-12 1 Contents Stage 9 Pages 29-31 The cuirass side and tassets Stage 10 Pages 32-37 The shoulder plate and tassets Stage 11 Pages 39-41 The shoulder plate
More informationGas Lines. Technical Manual. Sumitomo (SHI) Cryogenics of America, Inc Vultee Street Allentown, PA U.S.A.
Gas Lines Technical Manual Sumitomo (SHI) Cryogenics of America, Inc. 1833 Vultee Street Allentown, PA 18103-4783 U.S.A. Revision F: April 2008 261320A TABLE OF CONTENTS Page DESCRIPTION...1 SPECIFICATIONS...2
More informationRADIUS ROD BUSHING SET
RADIUS ROD BUSHING SET These are designed to allow your front suspension to operate much more freely than the factory units, with less maintenaance. STICKSION could be a key word here. The front end will
More informationI.H.S INSTALLATION INSTRUCTIONS
I.H.S INSTALLATION INSTRUCTIONS TOOLS REQUIRED The following tools will be required for installation of your I.H.S. system. Item Qty Needed 9/16 Open End Wrench 2 3/4 Open End Wrench 1 1/2 Open End Wrench
More informationwww.allsportsystems.com Page 1 of 29 Page 2 of 29 Table of Contents Items You Supply: 4 MICROBAY Setup Instructions 5 Items Provided By AllSportSystems: 5 MEASURING AND CUTTING THE 1 EMT POLES FOR THE
More informationThank you for purchasing a WIKE BOX BIKE!
Thank you for purchasing a WIKE BOX BIKE! Contents Safety.....3 Front wheel.4 Kickstand..5 Handle Bar & Box 6 Seat post and Saddle 7 Final pre-ride check 8 Tools needed to assemble Bike: -High table or
More informationPage 1 of 1 04/19/13 SBR
Office of Roadway Engineering - Plan Insert Sheets Number Title Date Number Title Date Number Title Date 201015 Extension of Anchor Bolts 07/20/12 207000 Bikeway Pavement Marking Details 01/18/13 202010
More informationFiber Cable Puller with Tuf-Lugger lite
7 OPERATING INSTRUCTION MANUAL Fiber Cable Puller with Tuf-Lugger lite Copyright 2015 DCD Design & Manufacturing Ltd. Revision 1.0 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING The Fiber
More informationInstallation Instructions
116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting
More informationInstant Garage 20' x 12' 3" x 8' 3"
Instant Garage 20' x 12' 3" x 8' 3" Assembly Instructions Description Model # Instant Garage 20' x 12' 3" x 8' 3" - Grey CIG 1220 3503502 Recommended Tools OR THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED
More informationStandard. Standard. Venepuncture Arm. Light. Part No: Brown. Part No: Black. Part No: 00332
Setup Guide Standard Standard Light. Part No: 000 Brown. Part No: 00 Black. Part No: 00 Part No: 065-964 Issue, June 0 0 Limbs & Things For more skills training products visit limbsandthings.com Limbs
More informationThe Discussion of this exercise covers the following points:
Exercise 5-3 Wet Reference Leg EXERCISE OBJECTIVE Learn to measure the level in a vessel using a wet reference leg. DISCUSSION OUTLINE The Discussion of this exercise covers the following points: Measuring
More informationFlat Fold Highchair INSTRUCTION MANUAL. Designed and manufactured to BS EN 14988: 2012 IMPORTANT:
Flat Fold Highchair INSTRUCTION MANUAL Designed and manufactured to BS EN 14988: 2012 IMPORTANT: Thank you for choosing our product. Please read and understand these instructions before using this flat
More informationUltrasonic Level Transmitter
Process Control Ultrasonic Level Transmitter Courseware Sample 85991-F0 Order no.: 85991-10 First Edition Revision level: 10/2017 By the staff of Festo Didactic Festo Didactic Ltée/Ltd, Quebec, Canada
More informationUniversal Elevator Mount Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A.
REQUIRED TOOLS AND MATERIALS: 2 Capable Adults Carpenter s Level 15 Tape Measure Pencil Universal Elevator Mount Owners Manual Customer Service Center N53 W2400 South Corporate Circle Sussex, WI 530 U.S.A.
More informationProof load is the load applied in performance of a proof test. Proof test is a nondestructive tension test performed by the sling manufacturer or an
1910.184 Slings (a) Scope. This section applies to slings used in conjunction with other material handling equipment for the movement of material by hoisting, in employments covered by this part. The types
More informationBKC100 SPRG Clamp For Wire Rope. Dimensions and Weight. Long Description. Manufacturer Information. Taxonomies, Classifications, and Categories
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 BKC100 SPRG Clamp For Wire Rope Cooper B-Line/Cable Tray Manufacturer Description Weight per unit Product Category Dimensions
More informationVented VW Pressure Transducer
Vented VW Pressure Transducer 52612499 Copyright 2008 DGSI. All Rights Reserved. This equipment should be installed, maintained, and operated by technically qualified personnel. Any errors or omissions
More informationUltra Tugger Cable Puller and Pulling Packages 6800 and 6805A
INSTRUCTION MANUAL Ultra Tugger Cable Puller and Pulling Packages 6800 and 6805A (115 V CE for United Kingdom) Serial Code ALA Read and understand all of the instructions and safety information in this
More informationExercise 2-2. Second-Order Interacting Processes EXERCISE OBJECTIVE DISCUSSION OUTLINE. The actual setup DISCUSSION
Exercise 2-2 Second-Order Interacting Processes EXERCISE OBJECTIVE Familiarize yourself with second-order interacting processes and experiment with the finer points of controller tuning to gain a deeper
More informationDM-WU (English) Dealer's Manual. Wireless Unit SM-EWW01
(English) DM-WU0001-00 Wireless Unit Dealer's Manual SM-EWW01 IMPORTANT NOTICE IMPORTANT NOTICE This dealer s manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally
More informationStandard Operating Procedures
Standard Operating Procedures GlassBore and GlassLine EUE 8RD Tubular Goods Composite Lining Systems Focus on Safety and Quality COMPOSITE LINING SYSTEMS Table of Contents Section 1 page 3 Arrival on Production
More informationInstallation Instructions - Steel 4 Spring Arm Kits , , , ,
Installation Instructions - Steel Spring Arm Kits 50-0709, 50-079, 50-0750, 50-075, 50-078 GR 8// 07-00 0 N. Marshall Ave. El Cajon CA. 900 For technical support call us at (800) 8-075 Step. Determining
More informationFlorida Building Code 6 th Edition (2017) Residential. Broward County Edition Loose-leaf Supplement
Board of Rules and Appeals FBC 6 th Edition (2017)- Residential - Supplement No. 1 January 1, 2018 Florida Building Code 6 th Edition (2017) Residential File removed pages for reference. Broward County
More informationEquipment. Box Equipment PROTECTION FROM ACCIDENTS PROTECTION FROM CONTACT. Running Shoes
Box Equipment Equipment PROTECTION FROM ACCIDENTS Running Shoes Select shoes for grip, ankle support and protection and match with the player s age and weight and level of play. Examples would be a high
More informationPuffin Sport and Saco
Puffin Sport and Saco Assembly and User Information Pakboats/ScanSport, Inc. Post Office Box 700 May Street Enfield, New Hampshire 03748 USA Phone: (888) 863-9500 (toll free) From outside the US: +1 (603)
More informationOPERATIONS and SAFETY MANUAL
OPERATIONS and SAFETY MANUAL LIFETIME WARRANTY SPECIAL SAFETY FEATURES: 1. Hook starts to open when device exceeds weight limit. 2. Latch Pops when weight is exceeded. At this point remove the load from
More informationINSTALLATION & MAINTENANCE INSTRUCTION
ARCHON Industries, Inc Liquid Level Gauges Models: BT-LLG ND-LLG INSTALLATION & MAINTENANCE INSTRUCTION Instruction No.: 1014.2 Revision Issued: 3/01/03 Approved: Engineering Manager Warning ONLY QUALIFIED
More information"RIGGING SAFETY IN CONSTRUCTION ENVIRONMENTS"
PRESENTER'S GUIDE "RIGGING SAFETY IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS
More informationOwner s Manual for Coaster Brake Bicycles This Owner's Manual contains assembly, operation, and maintenance instructions.
Your Model Number is: (write your model number here) Owner s Manual for Coaster Brake Bicycles This Owner's Manual contains assembly, operation, and maintenance instructions. WARNING: - Check operation
More information2019 MADONE ASSEMBLY MANUAL
2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and Di2 drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common
More informationDomed Ceilings and Barrel Vaults
Page 1 of 12 Domed Ceilings and Barrel Vaults USG Drywall Suspension System These installation instructions are divided into two parts: Part 1 applies to domed ceilings, and Part 2 applies to vaulted ceilings.
More informationReplacing the Reverse Osmosis ( RO ) Membranes
Replacing the Reverse Osmosis ( RO ) Membranes Changing your membranes is a relatively straightforward procedure that can be achieved by carefully following these instructions. During disassembly, water
More informationF-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME
F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10: TAILCONE F-1279-L UPPER LEFT
More informationWIRE ROPE PULLING MACHINE
WIRE ROPE PULLING MACHINE Spare parts list and exploded view Specifications Dimensions Item No. 0.8T 1.6T 3.2T 5.4T Rated Capacity kg 800 1600 3200 Rated Forward Handpower N 343 441 441 Rated Forward Travel
More informationHow do you build a cardboard boat?
How do you build a cardboard boat? 2015/2016 Campaign Kick-Off 8 th Annual Cardboard Boat Race Saturday, September 12, 2015 Dundee Lake Park Cardboard Boat Race 2015/2016 1 Boat Construction Rules The
More informationIndustrial Maintenance. Gear Drives 1. Job Sheets - Instructor F0
Industrial Maintenance Gear Drives 1 Job Sheets - Instructor 54334-F0 Order no.: 54334-3C First Edition Revision level: 11/2017 By the staff of Festo Didactic Festo Didactic Ltée/Ltd, Quebec, Canada 2017
More informationINSTRUCTIONS 360 Y-DROP HAGIE STS 2015
INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The
More informationFront derailleur. Dealer's Manual SORA FD-R3000 FD-R3030 CLARIS FD-R2000 FD-R2030. ROAD MTB Trekking. City Touring/ Comfort Bike DM-RBFD001-01
(English) DM-RBFD001-01 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Front derailleur SORA FD-R3000 FD-R3030 CLARIS FD-R2000 FD-R2030 CONTENTS IMPORTANT NOTICE... 3 TO
More informationSocket P2RF-05-S P2RF-08-S Clip & Release Lever Nameplate R99-11
Screwless Clamp Terminal Socket P2RF@@S Screwless clamping greatly contributes to reducing wiring time. No over or under tightening of cable connection so better contact reliability is achieved. Double
More informationKari-Tek. Kari-Tek. Hydro Skeg Retro-Fitting Instructions. Instructions for retro-fitting of Hydro Skeg
Kari-Tek Instructions for retro-fitting of Hydro Skeg A good knowledge of fibreglassing will be required to fit the Hydro Skeg successfully. When working with fibreglass and cutting the holes, safety glasses,
More informationStandard. Bag & Stand Advanced Venepuncture Arm. Light. Part No: Brown. Part No: Black. Part No: 00442
Setup Guide Bag & Stand Advanced Standard Light. Part No: 00440 Brown. Part No: 0044 Black. Part No: 0044 Part No: 065-0 Issue, May 0 0 Limbs & Things For more skills training products visit limbsandthings.com
More informationINSTALLATION INFORMATION
This publication contains a collection of general information related to the installation of power cables. The design of power cable installations and installation of power cables should be done by competent
More information12ft JumpPOD Classic / Deluxe. Please start with the following parts: 1x Top Tube (Key No. 2) and 1 x Enclosure A Socket (Key No.
User s Manual Update: Building the Frame The circular frame of the JumpPOD comprises 8 curved top tubes. There are 2 different types of Top Tube: Key No. 2 (detailed below) and Key No. 1(detailed overleaf).
More informationHoldUp Plus2. Safety Kit included: See additional instructions for installation. REAR WHEEL TRAY. BASE (1x) lock WASHER (1x) KEY (2x) SAFETY CLIP (1x)
HoldUp Plus2 InsTAll This product on 2" hitch version of the HoldUp Front WHEEL TRAY assembly (1x) REAR WHEEL TRAY assembly (1x) wrench (1x) BASE (1x) bolt (8X) Lock WASHER (8X) Washer (8x) KEY (2x) SAFETY
More informationIntroduction GUIDELINES FOR INSTALLATION PREINSULATED TUBE UNITHERM... Principal of Operation
GUIDELINES FOR INSTALLATION PREINSULATED TUBE UNITHERM... Introduction Principal of Operation The use of DEKORON/UNITHERM pre-insulated steam supply and condensate return lines offers cost savings features
More informationBike Fit Clinic. Regards, Missie Wakefield Owner
Bike Fit Clinic Thank you for your interest in the Bike Fit Clinic at The Bike Shop of Bel Air. Your interest in this class represents your enthusiasm and interest in maximizing your enjoyment with your
More informationSOLO TRIPOD SERIES Operator s Manual
SOLO TRIPOD SERIES Operator s Manual #1630 Solo DV 75mm 2-Stage Alloy Tripod #1501 Solo DV 75mm 2-Stage Carbon Fibre Tripod #1505 Solo ENG 100mm 3-Stage Tripod Features and Controls 75mm Bowl (#1501 &
More informationII-28 STOKES BASKET OPERATIONS
1 II-28 STOKES BASKET OPERATIONS Anchor Slings- (2) high strength nylon webbing straps with D-rings on both ends used to set an anchor. Max working load of 10,000 lbs. Bight- Element of knot formed by
More informationCO V E R S TA R AU TO MAT I C S A F E T Y CO V E R INSTALLATION GUIDE
CO V E R S TA R AU TO MAT I C S A F E T Y CO V E R DECKMOUNT SYSTEM INSTALLATION GUIDE SECTIONS System Parts Reference...3 Standard Top Track...4-6 Mechanism... 7-10 Cover Fabric...11-16 Home Owner & Builder
More information