INSTALLATION INSTRUCTIONS HELMET PAD KIT GENTEX Corporation
|
|
- Branden Chambers
- 6 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS HELMET PAD KIT 2005 GENTEX Corporation
2
3 INSTALLATION INSTRUCTIONS HELMET PAD KIT PART NUMBERS 00B AND 00B DESCRIPTION The helmet pad kit (Figure 1) permits the attachment of the adjustable pad suspension in the Tactical Ballistic Helmet (TBH) and the Police Ballistic helmet. The kit consists of hook fastener tapes of various lengths, adjustable pads, and two screws. The adjustable pad suspension system consists of a set of eight sizing pads attached to the attachment tapes inside the helmet shell. Three pads are attached at the front, three at the rear, and two in the crown area. (Exception: Kit 00B also has two extra pads to be installed at the sides.) The crown pads can be spaced farther apart to permit the use of an over-the-head headset. Each sizing pad consists of three impact-absorbing foam filler pads (two ¼ thick and one ½ thick) inside a cover. The ¼ foam pads can be removed or added to allow sizing adjustments for optimum stability and comfort. This booklet provides instructions for installing the kit. PADS SCREWS HOOK FASTENER TAPES COVER PAD DETAIL FOAM PADS Figure 1. Helmet Pad Kit 1
4 PROCEDURE Tools/Materials/Equipment Needed Flat-tip screwdriver Ruler or measuring tape Pencil Installing Hook Fastener Tapes 1. Remove the suspension and retention assemblies from the helmet. Set aside the screws, A-nuts, and retention assembly for reinstallation later. 2. Referring to Figure 2, install one 8-32 x 3/8 screw (supplied with the kit) and one of the existing A-nuts into the center front hole in the helmet. Install the other screw (supplied with the kit) and one of the A-nuts into the center rear hole of the helmet. NOTE INSIDE CENTER FRONT A-NUT (SCREW ON OUTSIDE) If necessary, you may cut the front and rear hook tapes to fit between the retention screw holes as shown in Figure 2. Ensure that the inner surface of the helmet is clean before you install the hook tapes. Clean the surface with isopropyl alcohol if necessary. INSIDE CENTER REAR A-NUT (SCREW ON OUTSIDE) Figure 2. Installing Screws and A-Nuts 2 3. Referring to Figure 3, measure, mark (with a small dot), and attach the hook tapes as follows: a. Measure and mark the 1x4 crown area hook tape locations ¾ from the reference mark on both sides. Attach the tapes along the marked locations, centered vertically on each side of the reference mark. b. Measure and mark the 1x7 front hook tape location ¾ from the helmet edge beading (on TBH helmets) or 1-3/8 from the helmet edge beading (on Police Ballistic helmets). Attach top edge of the tape along the mark, and center the tape horizontally between the front retention screw holes. c. Measure and mark the 1x2 hook tape locations 3/8 from the front retention screw hole locations and ¾ from the edge beading (TBH helmets) or 1-3/8 from the edge beading (Police Ballistic helmets). Attach the tapes as shown. d. Measure and mark the 1x7 rear hook tape location 1-3/8 from the helmet edge beading. Attach the bottom edge of the tape along the mark, with the tape centered horizontally between the rear retention screw holes. e. Attach the 1x4.5 rear hook tapes as shown so that a triangular space is formed between these tapes and the 1x7 rear tape. 4. Reinstall the retention assembly.
5 EDGE BEADING FRONT 3/4 ON TBH (WITHOUT BEAK) 1-3/8 ON POLICE BALLISTIC HELMET (WITH BEAK) RETENTION SCREW HOLE REFERENCE MARK 3/4 RETENTION SCREW HOLE 3/8 3/8 3/4 ON TBH (WITHOUT BEAK) 1-3/8 ON POLICE BALLISTIC HELMET (WITH BEAK) 3/4 ON TBH (WITHOUT BEAK) 1-3/8 ON POLICE BALLISTIC HELMET (WITH BEAK) 3/4 TRIANGULAR SPACE RETEN- TION SCREW HOLE RETEN- TION SCREW HOLE 1-3/8 REAR Figure 3. Hook Tape Installation 3
6 Installing Pads NOTE Most kits have six bottom pads (three to be installed in front, three in rear). However, kit 00B has eight bottom pads. The two extra bottom pads in kit 00B are to be installed on the sides. Figure 4 shows the locations. 1. Install the pads as shown in Figure 4. As you install each pad, ensure that: the pad is firmly fastened to the attachment tapes you installed previously. the opening in each pad cover faces the inside surface of the helmet. 2. Don the helmet, and check the fit in accordance with Pages 5 and 6. Make any necessary adjustments. LOCATION OF EXTRA BOTTOM PAD (KIT 00B ) BOTTOM PADS LOCATION OF EXTRA BOTTOM PAD (KIT 00B ) CROWN PADS BOTTOM PADS OPENING IN COVER PADS PAD DETAIL Figure 4. Adjustable Pad Suspension System 4
7 Checking Fit of Helmet 1. Have the wearer don the helmet. Allow the helmet to settle on the head for a few minutes before checking the fit. 2. Ensure that the bottom sizing pads are just above the brow ridge. If the helmet is too high, have the wearer remove the helmet. Referring to Figure 5, adjust the height as follows: a. Remove the two crown pads, noting their position inside the helmet. b. Remove one or both 1/4-inch-thick foam pads from each crown pad cover. WARNING Ensure that all helmet adjustment mechanisms are properly adjusted for a snug, secure fit at all times when the helmet is worn. Failure to do so can result in an unstable helmet that will not protect the wearer. Each sizing pad contains one ½-inch-thick foam pad and two 1/4-inch-thick foam pads inside the cover. For impact protection and helmet stability, you must keep all ½-inch-thick foam pads inside the sizing pads and all sizing pads properly installed in the helmet when the helmet is worn. Remove the 1/4-inch-thick pads only where necessary to adjust the fit. c. Reinstall both crown pads (with the ½-inch-thick foam pad inside each one) in the helmet in the same positions from which they were removed. Ensure that the opening in each crown pad cover faces the top of the helmet. ¼-INCH- THICK FOAM PADS CROWN PADS ½-INCH- THICK FOAM PAD d. Have the wearer don the helmet. Recheck the helmet height. Continued on next page PAD DETAIL Figure 5. Crown Pads 5
8 3. Ensure that the helmet fit is snug and secure, yet comfortable. As needed, have the wearer remove the helmet, refer to Figure 6, and adjust the bottom pads as follows: a. Remove the bottom pads from the helmet as needed, noting their position inside the helmet. b. Remove one or both 1/4-inch-thick foam pads from each bottom pad cover. c. Reinstall the bottom pads (with the ½-inch-thick foam pad inside each one) in the helmet in the same positions from which they were removed. Ensure that the opening in each bottom pad cover faces the top of the helmet. d. Have the wearer don the helmet again. Recheck the fit. BOTTOM PADS BOTTOM PADS TWO 1/4-INCH- THICK FOAM PADS ONE ½-INCH-THICK FOAM PAD OPENING IN CLOTH COVER Figure 6. Bottom Pads 6
9 PARTS LIST Helmet Pad Kit, Part Number 00B and 00B HELMET PAD KIT 00B Hook Fastener Tape, 1 x 7 Hook Fastener Tape, 1 x 4.5 Hook Fastener Tape, 1 x 4 Hook Fastener Tape, 1 x 2 Helmet Sizing Pad, TBH, Bottom 05D ea. Helmet Sizing Pad, TBH, Crown 05D ea. Screw, 3/8 75A ea. Helmet Pad Kit Instruction Booklet TP ea. HELMET PAD KIT 00B Hook Fastener Tape, 1 x 7 Hook Fastener Tape, 1 x 4.5 Hook Fastener Tape, 1 x 4 Hook Fastener Tape, 1 x 2 Helmet Sizing Pad, TBH, Bottom 05D ea. Helmet Sizing Pad, TBH, Crown 05D ea. Screw, 3/8 75A ea. Helmet Pad Kit Instruction Booklet TP ea. 7
10 NOTES
11
12 TP0286 SEPTEMBER 2005
Tactical Ballistic Helmet II (TBH II )
Care and Use Instructions Tactical Ballistic Helmet II (TBH II ) Mission Configurable (MC) TBH II MC TBH II HC-MC TBH II HST-MC 2013 Gentex Corporation When you replace components or install additional
More informationLIGHTWEIGHT HELMET (LWH)
TM-08744B-12&P OPERATOR'S CARE AND USE MANUAL FOR LIGHTWEIGHT HELMET (LWH) 8470-01-560-2866 - X-Small 8470-01-560-3267 - Small 8470-01-560-3076 - Medium 8470-01-560-3270 - Large 8470-01-560-3271 - X-Large
More informationMARINES CORPS *TM 08744B-OR/A-PMC-3 ARMY TM PMC-3 CREW/OPERATOR DAILY PREVENTIVE MAINTENANCE CHECKLIST FOR LIGHTWEIGHT HELMET (LWH)
MARINES CORPS *TM 08744B-OR/A-PMC-3 ARMY TM 10-8470-204-10PMC-3 CREW/OPERATOR DAILY PREVENTIVE MAINTENANCE CHECKLIST FOR LIGHTWEIGHT HELMET (LWH) NOTICE To effectively perform the tasks in this checklist,
More informationBALLISTIC OPTICAL ARMOR (BOA ) GOGGLE
USE AND CARE INSTRUCTIONS BALLISTIC OPTICAL ARMOR (BOA ) GOGGLE 2005 GENTEX Corporation Description............................................. 1 Standard Strap Configurations..................................
More informationTAL 803 (L) Rev. 4 MSA 2008 Prnt. Spec (EE) Mat Doc
TAL 803 (L) Rev. 4 MSA 2008 Prnt. Spec. 10000005389(EE) Mat. 10063328 Doc. 10063328 WARNING SUMMARY This warning summary contains general safety warnings and hazardous materials warnings that must be
More informationInstallation Manual. Version 12-10
Installation Manual The products and parts shown herein are to be installed and used adjusted in accordance with these instructions. Any deviation by the buyer, installer, or user from these instructions
More informationPARAMASTER HIGH ALTITUDE LOW OPENING (PM HALO) HELMET ASSEMBLY
Operation Instructions PARAMASTER HIGH ALTITUDE LOW OPENING (PM HALO) HELMET ASSEMBLY 2012 Gentex Corporation Contents SAFETY NOTICE............................ ii DESCRIPTION..............................
More informationLadies Shopper Bike Assembly Manual 28C03
Ladies Shopper Bike Assembly Manual 28C03 Ecosmo Ltd 1 Know your bike 1. Wheel 2. Rear Derailleur 3. Chain 4. Crank Set 5. Pedal 6. Seat Quick Lock 7. Saddle and Post 8. Frame 9. Front Light 10. Front
More informationCOMPLETE/SHELLS DESCRIPTION PART NUMBER NSN NUMBER ALSE NUMBER
HGU-56/P Part Numbers for the U.S. Army www.gentexcorp.com COMPLETE/SHELLS COMPLETE HELMET, HGU-56/P, U.S. Army Version, XX-Small 88D7590-1 8415-01-394-8032 1680-ALSE-101-1 COMPLETE HELMET, HGU-56/P, U.S.
More informationSOTR Special Operations Tactical Respirator
SOTR Special Operations Tactical Respirator OPERATOR S MANUAL FOR INDIVIDUAL RESPIRATORY PROTECTION OPS-CORE 2018 OMM G055-1000 REV. B INTRODUCTION ABOUT YOUR SOTR The Ops-Core Special Operations Tactical
More informationVanguard and Vanguard II Helmets
Vanguard and Vanguard II Helmets WARNINGS, CAUTIONS, AND INSTRUCTIONS THIS BOOKLET MUST BE CAREFULLY READ BY ALL INDIVIDUALS WHO WEAR OR MAINTAIN THIS HELMET, INCLUDING THOSE WHO HAVE ANY RESPONSI- BILITY
More informationChapter 9 Accessories for the Kirby Morgan BandMasks
Chapter 9 Accessories for the Kirby Morgan BandMasks 9.1 Introduction This section provides the manufacturer s advice on how to install KMDSI accessories including the hot water shroud, low pressure inflator
More informationAIRFRAME HELMET OPERATOR S MANUAL
AIRFRAME HELMET OPERATOR S MANUAL THIS MANUAL MUST BE CAREFULLY READ BY ALL PERSONS WHO HAVE OR WILL HAVE THE RESPONSIBILITY FOR USING OR MAINTAINING THIS PRODUCT. FAILURE TO USE AND MAINTAIN THE PRODUCT
More informationTroyer s Gourd Rack 8 unit F R H O P
B E A D I M-N L Vertical Parts F R H O P Horizontal Parts C G J Updated 11/16 Parts List A: Top of Pole B: Bottom of Pole C: 48 Ground Stake D: Top Perch rods 48 long E: Hub F: Rope Winder w/ attached
More informationSS650 HELMET USER MANUAL
SS650 HELMET USER MANUAL READ BEFORE USING YOUR SPEED AND STRENGTH HELMET Congratulations on the purchase of your new Speed and Strength motorcycle helmet. At Speed and Strength, we take great pride in
More informationPitts Model 12 Wing Leading edge Installation
Pitts Model 12 Wing Leading edge Installation This procedure is used to install molded plywood leading edges included in the Pitts Model 12 kit. Nine (9) molded leading edge section are require per aircraft;
More informationQuick Start Guide. HANS Device
Quick Start Guide HANS Device 2018 Pg. 2 The HANS Device Quick Start Guide Welcome - you re ready to use the same technology that protects the world s top racers. Follow these steps to get started. Install
More informationLightweight HGU-55/P Helmet Assembly
Operation and Maintenance Instructions with Illustrated Parts Breakdown Lightweight HGU-55/P Helmet Assembly 2011 Gentex Corporation When you replace components or install additional components on Gentex
More information2019 MADONE ASSEMBLY MANUAL
2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and Di2 drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common
More information(Specification changes are highlighted in yellow)
APPENDIX II SCRUTINEERING (Specification changes are highlighted in yellow) 101. ICF Canoe Polo Kayak Manufacturers Scheme 1.1. - After January 1 st 2015 - All new composite canoe polo kayaks manufactured
More informationThank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step*
PG 1 OF 9 PORTA-DOCK, INC. 74A ABL/APW 1056 & 44A FLB APW 1056 PORTA-LIFT Thank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step* STEP 1. Separate and group
More informationGurney Flap for WRX and STI w/low Profile Trunk Spoiler
Gurney Flap for 2015+ WRX and STI w/low Profile Trunk Spoiler 2017-12-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced
More informationTECHNICAL BULLETIN INSTALLATION AND FITTING INSTRUCTIONS FOR M45 MASK THERMOPLASTIC LINER
TECHNICAL BULLETIN INSTALLATION AND FITTING INSTRUCTIONS FOR M45 MASK THERMOPLASTIC LINER DISTRIBUTION STATEMENT C : Distribution authorized to U.S. Government agencies and their contractors to protect
More information2019 MADONE ASSEMBLY MANUAL
2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Disc brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common
More informationNOTES BEFORE USE BE SURE TO READ THIS MANUAL BEFORE USING THE HELMET. KEEP THE MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.
NOTES BEFORE USE BE SURE TO READ THIS MANUAL BEFORE USING THE HELMET. KEEP THE MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. 01 Chinstraps Chinstraps play an important role under an accident, preventing
More informationAGM 33 PIKE ALL FIBERGLASS. Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List
ALL FIBERGLASS AGM 33 PIKE Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List (1) Filament Wound Nose Cone w/ Metal Tip (1) Nose Cone
More informationMaintenance manual. Flight helmet LA100 PP
Flight helmet LA100 PP010298-00 Table of Contents Page Table of Contents 1/21 - Warning notice 2/21 - Helmet description 3/21 - Introduction 4/21 1 Chinstrap 5/21 2 Inner liner elements 6/21 3 Edge roll
More informationHoldUp Plus2. Safety Kit included: See additional instructions for installation. REAR WHEEL TRAY. BASE (1x) lock WASHER (1x) KEY (2x) SAFETY CLIP (1x)
HoldUp Plus2 InsTAll This product on 2" hitch version of the HoldUp Front WHEEL TRAY assembly (1x) REAR WHEEL TRAY assembly (1x) wrench (1x) BASE (1x) bolt (8X) Lock WASHER (8X) Washer (8x) KEY (2x) SAFETY
More informationCONTENTS I AM COURAGEOUS, BUT NOT RECKLESS I AM CONFIDENT, BUT NOT COCKY I AM TOUGH, AND I AM SMART I AM ALWAYS FOCUSED, AND ALWAYS AWARE
PLAYER S MANUAL TM I AM COURAGEOUS, BUT NOT RECKLESS I AM CONFIDENT, BUT NOT COCKY I AM TOUGH, AND I AM SMART I AM ALWAYS FOCUSED, AND ALWAYS AWARE I RESPECT MY TEAMMATES, AND MY OPPONENTS I LEARN FROM
More informationHorizontal Fuselage. Top Vertical Fuselage 1. Lay out the Top Vertical Fuse Front(1), Top Vertical Fuse Back(2), and Vertical Stabilizer(3).
Rumbuilder 71 B-17 Congrats on your Rumbuilder B-17! We re glad you chose to fly with us! If you have any problems, or missing/broken kit pieces, please contact us. We d be happy to replace any damaged
More informationOn the Go Swing System Instruction Manual
On the Go Swing System Instruction Manual WARNING READ ENTIRE MANUAL BEFORE USE. THIS SWING IS NOT A TOY. THIS SWING IS ONLY TO BE USED BY TRAINED PERSONNEL, SUCH AS AN OCCUPATIONAL THERAPIST, PHYSICAL
More informationA A A
Mossberg 0 GA Talon T Rear Pistol Grip with Scorpion Recoil System A.5.0.6 A.5.0.6 A.5.0.6 Extended Scorpion Material to Reduce and Discomfort to the Shooter's Hand and Thumb Sure-Grip Texture 70.0.0 Mossberg
More informationTECHNICAL MANUAL OPERATOR'S MANUAL FOR ADVANCED COMBAT HELMET (ACH)
*TM 10-8470-204-10 TECHNICAL MANUAL OPERATOR'S MANUAL FOR ADVANCED COMBAT HELMET (ACH) DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. *This manual supercedes TM 10-8470-204-10,
More informationROCKFON Island. Installation Guide. System Overview. 1. Island Sizes (Actual Dimensions)
System Overview Description Islands are frameless acoustic islands that feature a sharp painted edge underlined by a subtle and elegant bevel. The Islands are available in both square and rectangular shapes.
More informationA A A
Winchester SXP Talon T Rear Pistol Grip with Scorpion Recoil Grip A.5.0.65 A.5.0.65 A.5.0.65 Extended Scorpion Material to Reduce and Discomfort to the Shooter's Hand and Thumb Sure-Grip Texture Triton
More informationINSTALLATION INSTRUCTIONS A-Arm Guards, Rear Part Number: Application: Kawasaki Brute Force 750 4x4i
INSTALLATION INSTRUCTIONS A-Arm Guards, Rear Part Number: 88342 Application: 2012+ Kawasaki Brute Force 750 4x4i GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important. To
More informationSanta Fe Cycles Assembly Guide Introduction
Santa Fe Cycles Assembly Guide Introduction Congratulations on your purchase of your new Santa Fe bicycle. You have purchased a bicycle that has many features and qualities. Please take a few minutes and
More informationRAVE SUP STAND UP PADDLE BOARD User Guide/Owner s Manual
RAVE SUP STAND UP PADDLE BOARD User Guide/Owner s Manual ! W A R N I N G This product is not a lifesaving device. Always wear a nationally approved personal floatation device when using this product. Not
More information2012 K9100 COMPACT Worldwide Cycling Solutions Through Creative Innovations.
Home Instruction Sheet Step-1Please check for any missing parts. Model K9100 COMPACT (Basic AirCaddy) aircaddy web page 20 04/03/12 98% (1) T3230-00 METAL WHEEL TRUCK Model K8350 (Aircraft Kit) (Optional)
More informationProp Racer System. User Guide V0210
Prop Racer System User Guide 59718 V0210 Introduction The CO 2 dragster racing activity is popular with older students, but has eluded elementary students due to its complexity. Pitsco s latest race system
More informationAN AUTHORIZED SUPPLIER OF HELMETS TO THE NFL PLAYER S MANUAL VISIT: XENITH.COM CALL:
AN AUTHORIZED SUPPLIER PLAYER S MANUAL VISIT: XENITH.COM CALL: 866.888.2322 FITTING INSTRUCTIONS AN AUTHORIZED SUPPLIER INTRODUCTION A PROPER FIT IS INTEGRAL TO A HELMET S PERFORMANCE. PLEASE READ THE
More informationINSTALLING THE BOLT-IN-PLACE FOOTPLATE KIT (FIGURE 1)
Bolt-In-Place/Spring Button Assembly and Installation Instructions Kits No. 1110266 and 1121271 SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use.
More informationRetrofitting Green SkiErg Handles
Materials Needed 1 replacement cord* 1 Bulldog clip Measuring tape or ruler Scissors *Contains lanolin Procedure Overview Remove the SkiErg from the wall or floor stand Remove cover plates Remove old cord
More informationRecommended Climbing Helmet Characteristics:
STANDARDS FOR PROTECTIVE HEAD GEAR Analysis of the reports of previous accidents leads to the following conclusions: 1. Presently used hard hats (as distinct from a helmet), even though only moderately
More informationImportant Safety Information for Users of. Bashlin Climbers
Important Safety Information for Users of Bashlin Climbers - WA R NING For your personal safety, this booklet must be completely read and all of the information understood completely before using these
More informationOn the Go Swing System Instruction Manual
On the Go Swing System Instruction Manual WARNING READ ENTIRE MANUAL BEFORE USE. THIS SWING IS NOT A TOY. THIS SWING IS ONLY TO BE USED UNDER ADULT SUPERVISION. CONSULT WITH A CHILD S THERAPIST ON HOW
More informationSPINNER RIDE GETTING STARTED GUIDE. Welcome to a personalized fitness experience for your members
This addendum accompanies your equipment documentation and is additional information concerning the heart rate features for your equipment and console. Important The heart rate feature is intended for
More informationInstallatIon and owner s InstrUCtIons
InstallatIon and owner s InstrUCtIons Wall Mount Series Adjustable and Fixed Height Goal Systems table of Contents Safety Instructions... 2 Goal Specifications... 3 Frame Attachment... 4 Frame Assembly
More informationMAINTENANCE PROCEDURE FOR X 650
MAINTENANCE PROCEDURE FOR X 650 X 650 25. juli 2005-1/6 MAINTENANCE PROCEDURE FOR X 650 2 ND STAGE WARNING: This maintenance procedure is only for appointed Scubapro technicians that completed a course
More informationMarine 6-Boat Free-Standing Racks SKU: Updated November 2011
Marine 6-Boat Free-Standing Racks SKU: 30-061 Updated November 011 Contains: Marine -Boat Free-Standing Racks (SKU 1-003) Marine 3 rd Boat Expansion Racks (SKU 1-0303) Marine Back Legs (SKU -001) 3 Sets
More informationTruckSkin System Installation Manual
TruckSkin System Installation Manual TruckSkin 877-866-SKIN www.truckskin.com How to Install a TruckSkin Page 1...Questions? Call us at 877-866-7546 TruckSkin.com 1 2 Open your package and verify that
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Types A & B
Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)
More informationNotice. Destroy this document when it is no longer needed. Do not return it to the originator.
Notice Qualified requesters Qualified requesters may obtain copies from the Defense Technical Information Center (DTIC), Cameron Station, Alexandria, Virginia 22314. Orders will be expedited if placed
More information8MAY15 US RACK, Inc Falcon Drive, Madera, CA
8MAY15 US RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for Bedrail-mounted MOTORCYCLE RACK, Model 2001-4TRA WARNING: Do NOT attempt to install or use this rack without following
More informationSTATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING
9390 South 300 West, Sandy, Utah 84070 801-562-0123 800-782-0500 ColonialFlag.com STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE
More informationSS1700 HELMET USER MANUAL
SS1700 HELMET USER MANUAL Congratulations on the purchase of your new Speed and Strength MOTORCYCLE helmet. At Speed and Strength, we take GREAT pride in our gear and we know that it is the best possible
More informationROAD Wheel Set. Dealer's Manual WH-9000-C24-CL WH-9000-C24-TL WH-9000-C35-CL WH-9000-C35-TU WH-9000-C50-CL WH-9000-C50-TU WH-9000-C75-TU
(English) DM-WH0002-00 Dealer's Manual ROAD Wheel Set WH-9000-C24-CL WH-9000-C24-TL WH-9000-C35-CL WH-9000-C35-TU WH-9000-C50-CL WH-9000-C50-TU WH-9000-C75-TU WH-RS21 WH-RS61 CONTENTS IMPORTANT NOTICE...
More informationCaliber Sled Wheels Assembly Instructions for PN and 13579
Caliber Sled Wheels Assembly Instructions for PN 13576 and 13579 Caution: Read all instructions before assembling or using Sled Wheels. Follow the steps in order. Only use Sled Wheels as intended, following
More informationINSTALLATION INSTRUCTIONS FOR EXHAUST CUFF MODIFICATION
INSTALLATION INSTRUCTIONS FOR EXHAUST CUFF MODIFICATION Document # PCA1001-22 Revision LTR: A Date: 07/06/09 1 Notes: 1. The cuff must be installed onto the aircraft prior to painting. Once installed the
More informationTPLAnstallation, Fitting, and Maintenance for the SPH-4 Helmet
USAARL Report No. 88-18 TPLAnstallation, Fitting, and Maintenance for the SPH-4 Helmet (Script for Training Video) BY John V. Barson Douglas P. Pritts Bernard A. Lanoue Biodynamics Researqzh Division September
More informationParts List. 7. Handlebars 8. Grips 9. Handlebar Stem 10. Front Brake 11. Front Wheel 12. Crank 13. Chain
Woodworm Cruise Parts List 1. Free Wheel with Rear Hub 2. Fenders 3. Fender Stay 4. Quick Release 5. Saddle 6. Seat Post 7. Handlebars 8. Grips 9. Handlebar Stem 10. Front Brake 11. Front Wheel 12. Crank
More informationATD LB PRESSURE BLASTER INSTRUCTION MANUAL
ATD-8402 90LB PRESSURE BLASTER INSTRUCTION MANUAL SAVE THESE INSTRUCTIONS SAFETY INSTRUCTIONS FOR SANDBLASTER 1. Before opening the tank release the air pressure on the sand tank. To do this, turn off
More informationTOURNAMENT ICE. 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual
TOURNAMENT ICE 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual Thank you for purchasing a Gold Standard Games product. All of us at Gold Standard Games want you to be
More informationAPT Electrofusion Ducting
APT Electrofusion Ducting Installation Guide Franklin Fueling Systems 3760 Marsh Rd. Madison, WI 53718 USA Tel: +1 608 838 8786 800 225 9787 Fax: +1 608 838 6433 www.franklinfueling.com Safety Important!
More informationOwner s Manual Tourmaster Storage Cart
Owner s Manual Tourmaster CONTENTS Warranty.................................................................................2 Precautions.............................................................................2
More informationQRPGuys Single Lever Mini Paddle
QRPGuys Single Lever Mini Paddle First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationC - SERIES. Height Adjustable Portable Goal Supports. Installation & Owner s Instructions C1000 C2000. Made in the USA
C - SERIES Height Adjustable Portable Goal Supports C1000 C2000 Installation & Owner s Instructions Made in the USA This manual explains the proper installation, operation, and maintenance of your Schutt
More informationOversized Pulley Wheel System for SRAM etap Mounting & Maintenance
Oversized Pulley Wheel System for SRAM etap Mounting & Maintenance Congratulations with your new CeramicSpeed Oversized Pulley Wheel System for SRAM etap Personally, I want to thank you for joining the
More informationFairlane & Meteor Instruction Package RC-114K. Rear Coilover Suspension Kit NOTE...
ROD & CUSTOM Motorsports INCORPORATED 1962-1965 Fairlane & Meteor Instruction Package RC-114K Rear Coilover Suspension Kit NOTE... PLEASE READ ALL INSTRUCTIONS INCLUDED WITHIN THIS PACKAGE. IF AFTER READING
More informationSKYBIRD TRAP OWNER S / OPERATOR S MANUAL PARTS AND ASSEMBLY INSTRUCTIONS
SKYBIRD TRAP PART NO. 40903 OWNER S / OPERATOR S MANUAL PARTS AND ASSEMBLY INSTRUCTIONS WARNING: THIS MACHINE CAN CAUSE SERIOUS INJURY OR DEATH! THOROUGHLY READ INSTRUCTIONS AND SAFETY INFORMATION BEFORE
More information2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift
2,500/4,000 LB Easy Riser Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety
More informationProtective equipment for use in ice hockey. Part 2: Head protection for skaters
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 10256-2 First edition 2016-12-01 Protective equipment for use in ice hockey Part 2: Head protection for skaters Équipements de protection destinés
More informationUSER MANUAL. Contact details
Contact details Head Office: No 50, Kiepersol Crescent, Atlas Gardens, Contermanskloof, Durbanville, 7550, Cape Town, South Africa Tel: +27 21 557 7257 Fax: +27 21 557 7381 Email: info@leatt.com Website:
More informationImportant Note: Tighten lock nuts so the support tubes still swing freely see figure 2. There must be 1 2 threads of bolt past end of lock nuts.
Kit Contents: DESCRIPTION QTY. DESCRIPTION QTY. 2 Shank Assembly 1 Support Tube Assembly 1 Side Tube - Short 2 1-1/4 Shank 1 Center Tube - Long 1 3/8-16 x 2.0 Carriage Bolt 2 5/16-18 x 2.25 Carriage Bolt
More informationTriPod Safety Coupler Installation & Operating Instructions for Models TP4, TP5, TP6, and TP7
TriPod Safety Coupler Installation & Operating Instructions for Models TP4, TP5, TP6, and TP7 March 2014 Form FVC097 - Rev03 IMPORTANT: KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER.
More informationHOW-TO: Install a Wildcat Lighting System
Items needed: Acetone Isopropyl Alcohol Power Drill 8 zip ties Marine Goop 9/6 Drill Bit /6 Drill Bit Pencil or dry erase marker Measuring tape Extra wire Extra Grey Wire nuts Wire cutters Wire Strippers
More informationmodel - CYPRESS DX W
Contents model - CYPRESS DX W Maintenenace manual Read and Save these instructions Welcome Contents 1 Preparing Nothing makes us happier than seeing people out riding bikes. For over thirty years Giant
More informationMODEL #7100X A-FRAME LADDER
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #7100X A-FRAME LADDER LADDER MUST BE ATTACHED TO POOL FRAME... DO NOT USE WITH INFLATABLE POOLS ASSEMBLY AND INSTALLATION MANUAL The Anti-Entrapment
More informationVERTICAL SURFBOARD CARRIER READ ME! IMPORTANT WARNING!
VERTICAL SURFBOARD CARRIER ENG RRAC09 30 min READ ME! Thank you for purchasing a Front Runner Vertical Surfboard Carrier. Before you start, take a moment to familiarize yourself with this Fitting Instruction
More informationPole & Tree Climbers. Pole & Tree Climbers. 1972AR Series. Pole Climbers with 1-1/2" Gaffs Complete Set
MADE IN USA 8" x 8" (203 x 203 mm) cushioned, high-grade leather climber pads for maximum comfort. Adjustable climber length. Steel sleeve moves in 1/4" (6 mm) increments for the most comfortable fit.
More informationRUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More informationRemanufacturing Instructions HP 1320 Toner cartridge
HP 1320 Toner cartridge For, please call (800) 322-8992 OEM Reference Information OEM Product #: Q5949X OEM Yield: 6,000 pages @ 5% Coverage Fig. 1 1. To separate the cartridge sections, first remove the
More informationShoreline Cantilever Lift 2500lb Capacity Models: (108" inside width) - Part # (120" inside width) - Part #
Shoreline Cantilever Lift 2500lb Capacity Models: 25108 (108" inside width) - Part # 1017402 25120 (120" inside width) - Part # 1017403 1. 2. 3. 4. 5. CAUTION - PUT SAFETY FIRST Before attempting to install
More informationShimano Di2 Installation on S5
Installing Shimano Dura Ace Di2 Shifting Systems Note these instructions and pictures are for assembling the Shimano Dura Ace Di2 system (Internal Spec) on the Cervélo S5 frame. The Shimano Ultegra Di2
More informationRocky Mountain Element Technical Manual. Rev B
Rocky Mountain Element Technical Manual Rev B 1 Table of Contents Materials Required... 3 Suspension Pivot Torque Guide... 4 Small Parts Torque Guide... 5 Assembly Instructions... 6 1) Bearing Installation...
More informationRUDDER KIT INSTRUCTIONS
C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,
More informationINSTALLATION INSTRUCTIONS FOR: RE4548 JK FRONT COILOVER KIT
RUBICON EXPRESS 3290 MONIER CIR., RANCHO CORDOVA, CA. 95742 866-533-7706, www.rubiconexpress.com INSTALLATION INSTRUCTIONS FOR: RE4548 JK FRONT COILOVER KIT Safety Warning: Suspension systems or components
More informationThe advantages of the Impact NecksGen unit
The advantages of the Impact NecksGen unit Comfort The body forming pads place very little pressure on your collar bone, making the unit extremely comfortable and unlikely to create injury to your collarbone
More informationCover EX Installation Instructions
Cover EX Installation Instructions 1. Lay out all the parts and verify that they are all present according to the Cover EX Parts and Hardware List. See Fig 1. Call 800-730-7727 for all replacement and
More informationAssembly Instructions And User Guide
EZ-1/EZ-CLASSIC QUADRIBENT By Blackbird Designs Inc. Mark 5.2 June 2011 Assembly Instructions And User Guide 1 The Quadribent is 2-seat, side-by-side, human powered vehicle that enables almost anyone to
More informationOwner s Manual 700c Fixed Gear Bicycles
Owner s Manual 700c Fixed Gear Bicycles This manual contains important safety, assembly, operation and maintenance information. Please read and fully understand this manual before operation. Save this
More informationHEAVY DUTY SIT-UP BENCH SF-BH6502 USER MANUAL
HEAVY DUTY SIT-UP BENCH SF-BH6502 USER MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain owner s manual for future reference. For customer service, please contact: support@sunnyhealthfitness.com
More informationItem N o.: Item N am e:40cm Boys Rival Bike
Item N o.:42272892 Item N am e:40cm Boys Rival Bike 9 bell 8 grip 30 crash pad 10 brake lever 26 wheel reflector 22 saddle 23 seat post 25 rear reflector 24 quick release 6 handle bar 7 stem 2 top tube
More informationCAUTION - PUT SAFETY FIRST
www.shoremaster.com DVS Vertical Lift (Double V Side): Frame ssembly Instructions. Models: 500DVS - 0ft Wide, 5000lb Capacity - Part #: 0079 600DVS - 0ft Wide, 6000lb Capacity - Part #: 0033.. 3.. 5. CUTION
More informationBefore you start! Is iwalk 2.0 right for you?
Before you start! Is iwalk 2.0 right for you? Physical Abilities Requirements 1. Stair Test Before your injury, could you easily walk up and down stairs at normal speed, without using the hand rail? 2.
More informationAmerican Flagpole & Flag Co. 1(800)
SENTRY CONCEALED HALYARD-REVOLVING TRUCK GROUND SET INSTALLATIONS INSTRUCTIONS 1. Dig foundation as detailed in SECTION A FOUNDATION SPECIFICATIONS, set sleeve in enter of hole with top 2 above grade.
More informationFolding Dual Suspension MTB. Instruction Manual
Folding Dual Suspension MTB Instruction Manual Introduction The Stowabike Folding MTB has been made to last and with proper maintenance, it will give you years of enjoyable rides and journeys. The following
More informationU STAND INSTALLATION INSTRUCTIONS
U STAND INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new U STAND by Stand N Fish. Once installed on your kayak the U STAND will enhance your kayak fishing enjoyment to a whole new
More informationBelow are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
More informationBackCountry ebikes 2019 MULE Assembly
BackCountry ebikes 2019 MULE Assembly Required Tools: Cutting Pliers (to cut box poly strapping and heavy bike banding) Scissors (to remove bubble wrap) Allen wrenches (3mm, 4mm, 5mm, 6mm) Wrenches (10mm,
More information