HOW-TO: Install a Wildcat Lighting System
|
|
- Della Johnson
- 5 years ago
- Views:
Transcription
1 Items needed: Acetone Isopropyl Alcohol Power Drill 8 zip ties Marine Goop 9/6 Drill Bit /6 Drill Bit Pencil or dry erase marker Measuring tape Extra wire Extra Grey Wire nuts Wire cutters Wire Strippers Blue Wire nuts Heat shrink (optional) Wire crimpers Dry bag or battery bag Lay out contents of the kit. Ensure you have two white lights, one red light, and one green light for the navigation a. Test the lights to ensure proper function and to double check for correct colors. Starting with one of the white lights at the rear of your kayak position the light so that the wire extends toward the front of the boat. a. Since every kayak is different there is no hard measurement for light positions, therefore you must ensure that your light: i. Will be rear and side facing ii. Will be above the water line iii. Does not sit on top of the kayak with the light pointing towards the sky. iv When you are happy with the placement of the light, mark a spot on the boat where the wire exits the light. Use a pencil or dry erase marker so you can erase and remark if necessary. a. Ensure that the spot you have chosen will not interfere with or sever a rudder line or any other internal structures.
2 Once you are sure about your placement drill a 9/6 hole at your mark. Feed the wire through the hole until all wire is inside the boat and the light is sticking up. 6 Using a factory point on your kayak such as a pad eye that is on both sides measure the distance to the hole and transfer your mark to the other side. 7 Repeat steps 6 on the other side of the kayak.
3 8 Move to the front of your kayak and place the red light on the right side (you should be facing the boat) of the kayak, and the green light on the left side (still facing the boat) with the wires extending towards the rear of the kayak. a. Again, since every kayak is different there is no hard measurement for light positions, therefore you must ensure that your light: i. Will be forward and side facing ii. Will be above the water line iii. Do not sit on top of the kayak with the light pointing towards the sky. 9 When you are happy with the placement of the light, mark a spot on the boat where the wire exits the light. Use a pencil or dry erase marker so you can erase and remark if necessary. a.ensure that the spot you have chosen will not interfere with or sever a rudder line or any other internal structures. 0 Once you are sure about your placement drill a 9/6 hole at your mark. Feed the wire through the hole until all wire is inside the boat and the light is sticking up
4 Using a factory point on your kayak such as a pad eye that is on both sides measure the distance to the hole and transfer your mark to the other side. Repeat steps 9 on the other side of the kayak. Fishing Lights the rear of the boat.
5 a. Since every kayak is different there is no hard measurement for light positions, therefore you must ensur i. Will be forward and down facing ii. Will be above the water line iii. Are below the navigation lights iv. Are below the longitudinal seam of the kayak When you are happy with the placement of the light mark a spot on the boat where the wire exits the light. Use a pencil or dry erase marker so you can erase and remark if necessary. a. Ensure that the spot you have chosen will not interfere with or sever a rudder line or any other internal structures. Once you are sure about your placement drill a 9/6 hole at your mark. Feed the wire through the hole until all wire is inside the boat and the light is sticking up. 6 Using a factory point on your kayak such as a pad eye that is on both sides measure the distance to the hole and transfer your mark to the other side. Repeat steps on this side of the kayak. 7 The amber colored bug lights will be located in the cabin area of your kayak such that they will cover your body with the light they emit. a. Since every kayak is different there is no hard measurement for light positions, therefore you must ensure that your bug light: i. Will be inward and slightly upward facing ii. Will not be positioned such that it blinds you iii. Will not be in the place that you want to mount your switches iv. The wires will face towards the direction of the future battery location
6 8 When you are happy with the placement of the light mark a spot on the boat where the wire exits the light. Use a pencil or dry erase marker so you can erase and remark if necessary. a. Ensure that the spot you have chosen will not interfere with or sever a rudder line or any other internal structures. 9 Once you are sure about your placement drill a 9/6 hole at your mark. 0 Feed the wire through the hole until all wire is inside the boat and the light is sticking up. Using a factory point on your kayak such as a pad eye that is on both sides measure the distance to the hole and transfer your mark to the other side. Repeat steps 8 0 on this side of the kayak. i ting F Lights Determine the desired location for your battery, generally the center hatch. Fish the wires for the rear navigation lights forward, along either side of the kayak toward the desired battery location. a. Ensure that the wires do not interfere with any rudder lines b. Ensure the wires run outside of all scupper towers\ It may be desirable to tie one of the wires into the other to: a. Lessen the amount of wire running through the boat b. Provide you with extra wire before inserting the wires into the wire nut. a. Always test the light after making a splice in the wires
7 Run the wire(s) such that there will be about of slack at the desired switch location. a.if tying wires into one another you must use Marine Goop at all splices b. Test all lights after making a splice to ensure you have a good connection You will need a main power lead that will go from the switches to the battery. a. Ensure the main power lead will be long enough to go from the switches to the battery with 8 of slack. Connect the lead lines of the switches to the red wire of the main power lead. a. Ensure you use a blue wire nut and Marine Goop for the connection. Connect all the black wires of the lights to the black wire of the lead line a. Ensure you use a blue wire nut and Marine Goop for the connection. Attach the red wire for the navigation lights to the remaining lead on one of the switches. a. Ensure you use a blue wire nut and Marine Goop for the connection. Attach the red wire for the bug lights to the remaining lead on one of the switches. a. Ensure that you use a grey wire nut and Marine Goop for the connection
8 6 a. Ensure that you use a grey wire nut and Marine Goop for the connection 7 Test all lights by hooking the main power lead to the battery and testing the switches. a. At this time also note which switch powers which lights. 8 Place the battery in the desired location. 9 Crimp the female terminals included with the kit to the free ends of your main power lead. a. You can use heat shrink around one of the terminals to annotate which is the power and which is the neutral line if desired. 0 Test all lights and connections by hooking the main power lead to the battery and testing the switches. Place the battery into the dry bag and roll bag shut with extra main power lead wires, or mount battery in battery bag.
9 nting th it h s Determine desired location for mounting the switch (es). a. Since every kayak is different there is no hard measurement for switch positions, therefore you must ensure that your switch(es): i. Will not interfere with rudder lines or internal structures of the kayak ii. Will be convenient to reach iii. Will not be accidently bumped on or off iv. Will not interfere with kayak egress and ingress v. Will not interfere with paddling When you are happy with the placement of the switch, mark a spot on the boat with a pencil or dry erase marker so you can erase and remark if necessary. a. Ensure that the spot you have chosen will not interfere with or sever a rudder line or any other internal structures. If using more than one switch an ideal measurement for locating other switches is cm from mark the initial mark. Once you are sure about your placement drill a /6 hole at your mark. Unscrew the rubber cover from the switch (es). 6 Insert the switches through the underside of the kayak and place into corresponding /6 holes. a. Place the Navigation lights in the easiest to r bug lights. This places the switches in order of most frequent use. 7 Begin screwing rubber switch covers back onto switches to lock switches into place. a. Ensure all switches are lined up such that the up position switches lights on, and down switches them off.
10 i n n Light nting Using 8 zip ties strap the wiring so that it is out of the way a. Since every kayak is different there is no perfect place for wire management, therefore you must ensure that your wiring: i. Will not interfere with rudder lines or internal structures of the kayak ii. Will not be pulled loose when putting items in the hatches When you are happy with the wire management you can prepare the mounting surface for mounting the lights. Using a clean paper towel wet with acetone, thoroughly wipe the area of the kayak where you intend to place each light. Follow up by wiping the area again with the kit provided isopropyl alcohol pad. Break the glass vial inside the priming pen and squeeze until the tip is saturated with the priming liquid. 6 7 Liberally apply the primer to the area where the lights will be, from the hole you drilled outward to just beyond the length of the light strips. Wait minutes after applying the primer before removing the backing to the self adhesive strips on the lights.
11 8 kayak. a. Ensure the wiring is totally within the hole you drilled. b. Apply the light from the hole outward t of the backing away, pressing the light in place as you peel more away. 9
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
More informationULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS
ULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS TOOLS NEEDED: DRILL ¼ DRILL BIT ¾ HOLE SAW 3/16 DRILL BIT PHILLIPS HEAD SCREWDRIVER 7/16 WRENCH HEAT SOURCE: PROPANE TORCH, LIGHTER OR HOT AIR GUN WIRE CUTTER
More informationKayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions
Kayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions Copyright 2011 by R. E. & D. L. Conlon Kit Contains: Right & Left SpraySkirts 3 Long Black Wire Ties* 3 Short Black Wire Ties* 1 3/16
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationRUDDER KIT INSTRUCTIONS
C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,
More informationKari-Tek. Kari-Tek. Hydro Skeg Retro-Fitting Instructions. Instructions for retro-fitting of Hydro Skeg
Kari-Tek Instructions for retro-fitting of Hydro Skeg A good knowledge of fibreglassing will be required to fit the Hydro Skeg successfully. When working with fibreglass and cutting the holes, safety glasses,
More informationRUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More informationRef Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More informationESOCCI RIGGING MANUAL
ESOCCI RIGGING MANUAL 1 Spray Covers Hull Rear Iako Forward Iako Ama ESOCCI RIGGING MANUAL 2 When training & racing in outrigger canoes, the canoe is your protector on the water and therefore it is imperative
More informationHobie Island Spinnaker Instructions
Hobie Island Spinnaker Instructions Please read through the instruction manual before using this product. 2 Installation Components 1. 2. 1. Swivel Cam Cleat 2. Mount for Cleat w/ Hardware 3. Padeye w/
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationAdvancedTrak Rudder Kit AE4005. Assembly and Installation Instructions
AdvancedTrak Rudder Kit AE4005 Assembly and Installation Instructions Thank you for your purchase of the Advanced Elements AdvancedTrak Rudder Kit! A Kayak Rudder is a great way to enhance the tracking
More informationU STAND INSTALLATION INSTRUCTIONS
U STAND INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new U STAND by Stand N Fish. Once installed on your kayak the U STAND will enhance your kayak fishing enjoyment to a whole new
More informationRustic Home Safety Gate
27980 Please read the following instructions carefully. Keep this instruction manual for future reference. Tools required: Phillips head screwdriver, drill (for top of stair installation), and pencil (not
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationSTERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight
STERN MOTOR FOOT CONTROL KIT For use with the Torqeedo 403 Ultralight The Wilderness Systems Foot Control Kit is designed to connect directly to a Torqeedo 403 Ultralight motor mounted on the stern of
More informationWHERE TO INSTALL THIS MIRROR
ROUND LED MIRRORS 3003-L-60 3005-L-60 BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION. 1) General Information Please inspect this product upon delivery. Any missing parts or manufacturing defects
More informationSound Stations. Exploring Sound. MDCPS - Department of Mathematics and Science
Sound Stations Exploring Sound Station 1 How does sound travel through solids? 1 zip lock bag 3 cups of sand 1 Pencil 1. Fill the zip lock bag with 3 cups of sand. Get as much air out of the bag as possible.
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO KAYAKS IMPORTANT: Tandem models will require the Wildy Supplemental kit in addition to this kit. The Supplemental kit provides extension straps and extra footbraces that allow rudder positioning
More information830 SureFlo Soap Systems Installation Instructions. Foam Soap Cabinet... Pages 2-9 Liquid Soap Cabinet... Pages 10-19
830 SureFlo Soap Systems Installation Instructions Foam Soap Cabinet... Pages 2-9 Liquid Soap Cabinet... Pages 10-19 INSTALLATION INSTRUCTIONS SureFlo SOAP DISPENSING SYSTEM FOAM VERSION ONLY B-830 Foam
More informationLectric Cycles Mid-Drive Electric Motor Installation
Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on
More informationStep 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.
WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the
More informationAssembly instructions nortik scubi 2 Recreational kayak
Assembly instructions nortik scubi 2 Recreational kayak QR-Code assembly video: Assembly instructions nortik scubi 2 Dear Customer, You have purchased a nortik scubi 2, an innovative hybrid kayak for recreational
More informationInstallation Instructions - Electric Steel Drive Systems for Arm Sets to ,
Installation Instructions - Electric Steel Drive Systems for Arm Sets to 22 208-025, 209-025 NB /0/ 607-0029 404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 Step.
More informationShimano Di2 Installation on S5
Installing Shimano Dura Ace Di2 Shifting Systems Note these instructions and pictures are for assembling the Shimano Dura Ace Di2 system (Internal Spec) on the Cervélo S5 frame. The Shimano Ultegra Di2
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationDear Skier, Thank you for choosing GOODE! GOODE SKI TECHNOLOGIES. Dave Goode Founder/President
Dear Skier, Congratulations on your purchase of the new PowerPlate System! This revolutionary system eliminates the need to ever drill another hole into your ski. Engineered for just about every binding
More informationSEADUCER BOATS GAS SPORT HYDRO
SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationInstallation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems , ,
Installation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems - 204-025, 206-025, 22-025 NB /0/ 607-0020 404 N. Marshall Ave. El Cajon CA. 92020 For technical support
More informationThe Outer Seal is highly abrasion resistant and provides mechanical stiffness to the splice in order to better match the cable stiffness.
The Sealing Compound encapsulates the electrical splices, provides a strain relief for the conductors, acts as a water block, eliminates air voids which tend to act as pumps to draw in water during pressure
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationPitts Model 12 Wing Leading edge Installation
Pitts Model 12 Wing Leading edge Installation This procedure is used to install molded plywood leading edges included in the Pitts Model 12 kit. Nine (9) molded leading edge section are require per aircraft;
More informationDIY Shallow Water Anchor Assembly Instructions for Rods, T-grips, Stainless Tips, Stainless Couplers, and the 4-in-1 Paddle
DIY Shallow Water Anchor Assembly Instructions for Rods, T-grips, Stainless Tips, Stainless Couplers, and the 4-in-1 Paddle All Shallow Water Anchor Parts First, start by laying out and identifying all
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SureFlo Soap Dispensing System Bobrick SureFlo Soap Dispensing System Soap Cabinets, Soap Dispensers and connections are available from all Bobrick Distributors. Bobrick SureFlo
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More informationHOME ASSEMBLY INSTRUCTIONS
HOME ASSEMBLY INSTRUCTIONS This Papillionaire Bicycle now belongs to you. It will take you to work, wait patiently outside your local cafe, and carry your groceries home. This is the start of your long-term
More informationwww.myrower.com support@myrower.com ASSEMBLY Congratulations on purchasing the MyRower! Please see the following pages for instructions on assembling your MyRower. Bits bag contents: Rail Cross Bolt (90mm)
More informationTripod Setup Guide (M-TPx)
Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for
More informationaero naut Order No. 3009/00
aero naut Order No. 3009/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually numbered.
More informationFirst Team Sports, Inc. Stellar Recreational Volleyball System
First Team Sports, Inc. Stellar Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 2 Height Labels L 2 Carabiner Clip C 3 Net Clamp M 1 ½ x 2 Hex Bolt
More informationDOYLE Cradle Cover MANUAL
DOYLE Cradle Cover MANUAL The Doyle Cradle Cover Upon receiving your new Doyle Cradle Cover and before starting actual installation, we recommend laying out your Cradle Cover on a hard surface in a secure
More informationBrushbot Kit Instructions: Parts
Brushbot Kit Instructions: Parts or AG13 Googly eyes Additional Tools Needed: Scissors or snips, hot glue gun or some type of glue suitable for plastic (epoxy or super glue should be fine). Brushbot Kit
More informationA-FRAME RESIN IN & OUT FLIP UP LADDER
A-FRAME RESIN IN & OUT FLIP UP LADDER NE1222 NOTE FOR SAFETY PURPOSES ALL LADDERS SHOULD BE SECURED BY ATTACHING THEM TO THE TOP LEDGE OF THE POOL. (See step 13 for details) In order for the ladder to
More informationASSEMBLY INSTRUCTIONS FOR THE SHOOTOUT HOOPS GAME
1 ASSEMBLY INSTRUCTIONS FOR THE SHOOTOUT HOOPS GAME Please keep these instructions for future reference. Adult assembly required. Tools / Parts required This product requires 3x AA batteries (not included).
More informationLITERIDER 2&3 IMPORTANT WARNING. 2Bike (1x) Bolt (1x) Nut (1x) Small Hex Wrench (1x)
LITERIDER 2&3 3 Bike (1x) Bolt (1x) Flat Washer (2x) Nut (1x) Large Hex Wrench (1x) 2Bike (1x) wrench (1x) Small Hex Wrench (1x) keys (2x) Long Strap (1x) 2-Zip Strips (6x) 3-Zip Strips (9x) Wheel strap
More informationTechnical Bulletin. Parts and Service News. LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6
Equipment Affected Technical Bulletin LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6 Ford 4.2L V-6 powered tractors with LPG fuel systems. Part Description Discrepancy Fuel Pressure Lock-off
More informationw w w.ro swellmarine. com Part 1 Installation Part # C # C
w w w.ro swellmarine. com Pro Bimini Part 1 Installation Part # C915-119151 # C915-119152 Information: info@roswellmarine.com If you have any questions please call : 1-321-638-1331 REV 16-JUL-18 Moomba
More informationSemi Freddo Snow kite [Ram Air]
User manual Semi Freddo Snow kite [Ram Air] This manual gives you detailed instructions on how to use your new Semi Freddo kite. We recommend you take your time to read the instructions. In case you have
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More informationespin - Bicycle Generator
espin - Bicycle Generator NO TOOLS REQUIRED Thanks for purchasing the Tesla Energy portable bicycle generator. We are excited for this product to help your energy needs. With lots of testing, we have come
More informationBMW Motorrad. Installation Instructions. BMW Motorrad Communications System for Schuberth C3
BMW Motorrad Installation Instructions BMW Motorrad Communications System for Schuberth C3 Order No. 01 29 2 219 831 BMW Motorrad 05/2011 Be sure to read these instructions carefully and completely before
More informationInstallation Manual. Version 12-10
Installation Manual The products and parts shown herein are to be installed and used adjusted in accordance with these instructions. Any deviation by the buyer, installer, or user from these instructions
More informationInstallation Instructions
WHAT S IN THE BOX Charger RAM mount Not included in the box Kayak sensor Paddle sensor Rail mount PADDLE SENSOR INSTALLATION Step 1: Placement Use the right blade side of your paddle, the rail should be
More informationAccess Dinghy. Electrics. Installation. Manual
Access Dinghy Electrics Installation Manual SA1.e May, 00 ELECTRICS INSTALLATION MANUAL 1. Mark (using old cutout) and drill a pilot hole as the centre for inspection port in the starboard or right side
More informationBoat Boat Loader Fitting Instructions
Aerodynamic & Heavy Duty Roof Rack Systems Australian Made - Australian Owned www.rhinorack.com Boat Boat Loader Fitting Instructions CONTROLLED Balance point 3 Front eye nuts position 3 Transom eye nut
More informationDarling Downs Soaring Club Inc
Darling Downs Soaring Club Inc Rigging and De-Rigging Instructions LS7 XOW Overview Page 2 Rigging page 3 De-Rigging page 19 Overview It is the pilot s responsibility to make sure that the trailer is fully
More informationParts: Included in the parts box: Inner Rear Tire Tray. Inner Front Tire Tray. Trail Doc Clamp. Pivot Assembly. Trail Doc Post.
NV 2.0 2 Parts: Outer Front Tire Tray Inner Front Tire Tray Outer Rear Tire Tray Inner Rear Tire Tray Pivot Assembly Trail Doc Clamp Trail Doc Post Included in the parts box: 6mm Allen Wrench M6 Lock Washer
More informationFor ELECTRIC ANCHOR WINCH Models: T Pontoon 35 T sw Salt Water Series Coastal 35
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ELECTRIC ANCHOR WINCH Models: T10109-35 Pontoon 35 T10102-35sw Salt Water Series Coastal 35 If you have any questions or difficulty installing
More informationIMPORTANT WARNING SOUL PAD (2X) PAD STRAP (4X) S.U.P. BRAH (1X) KEYS (2X) RIPCORD (2X) HOOK (2X) NOSE/TAIL STRAP (2X)
SOUL PAD (2X) PAD STRAP (4X) S.U.P. BRAH (1X) KEYS (2X) HOOK (2X) RIPCORD (2X) NOSE/TAIL STRAP (2X) IMPORTANT WARNING IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED
More informationOWNER'S MANUAL FREE FALL ROPE AND CHAIN ANCHOR WINCH. 12 Volt Powered Winch Power-In / Freewheel-out operation. 36', 41' and 46' Class Anchor Winch
OWNER'S MANUAL 36', 41' and 46' Class Anchor Winch FREE FALL ROPE AND CHAIN ANCHOR WINCH PW46101 12 Volt Powered Winch Power-In / Freewheel-out operation These instructions apply to all models listed.
More information2019 MADONE ASSEMBLY MANUAL
2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and Di2 drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common
More informationWIND CLIPPER KTS ILLUM SCALE INC DEC CLIPPER WIND SYSTEM
CLIPPER WIND KTS ILLUM SCALE DEC INC CLIPPER WIND SYSTEM TABLE OF CONTENTS INTRODUCTION PRE-TEST OF INSTRUMENT INSTALLING THE MASTHEAD SENSOR UNIT INSTALLING THE DISPLAY NORMAL OPERATION CHANGING THE
More informationAliphatic Resin Wood Glue. 18" Fabric Parachute Part #PNC50 Part # Part #11700 Part #J0016. Launch Lug
ADANCED * What you will need to build the Quest High-Q Hobby Knife * Straight Edge Pencil Aliphatic Resin Wood Sanding Sealer & Brush Spray Paint Parts and exploded view of the Quest High-Q Nose Cone 18"
More informationFor ANCHOR WINCH Model: T Big Water 45 T sw Salt Water Series Big Water 45
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ANCHOR WINCH Model: T10110-45 Big Water 45 T10103-45sw Salt Water Series Big Water 45 If you have any questions or difficulty installing this
More informationChildren s University Tasmania Monthly Challenge Make your own Robo Wheel
Children s University Tasmania Monthly Challenge Make your own Robo Wheel Have you ever spun a Top? A top is a flywheel, a spinning disc that stores energy. Once a flywheel gets going, the stored energy
More informationSanta Fe Cycles Assembly Guide Introduction
Santa Fe Cycles Assembly Guide Introduction Congratulations on your purchase of your new Santa Fe bicycle. You have purchased a bicycle that has many features and qualities. Please take a few minutes and
More informationFinal Assembly Instructions Bikes with 16 Wheel Size
Final Assembly Instructions Bikes with 16 Wheel Size Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationPakboats PakCanoe Assembly Instructions
Pakboats PakCanoe Assembly Instructions Note: Please read these assembly instructions carefully before assembling the canoe. a A. Assembling the canoe Note: Don't be afraid to get into the canoe while
More informationKAYAK ERGOMETER. Operating Instructions (Rev 3.0)
KAYAK ERGOMETER Operating Instructions (Rev 3.0) Weba Sport und Med.- Artikel GmbH Liesneckgasse 6/1 1210 Vienna Austria Tel.: ++43 1 2723550 Fax: ++43 1 27235504 office@webasport.at www.weba-sport.com
More informationOWNER'S MANUAL FISHING AND PONTOON BOAT ANCHOR WINCH. 24' Class Rope Anchor Winch
OWNER'S MANUAL 24' Class Rope Anchor Winch FISHING AND PONTOON BOAT ANCHOR WINCH PW24101 The 24 Class anchor winch is a 12VDC power winch that retrieves and deploys river, mushroom, or navy type anchors
More informationSEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
More information1. Set up your Stick Up Cam Wired.
Stick Up Cam Wired 1. Set up your Stick Up Cam Wired. Download the Ring app. The app walks you through setting up and managing your Stick Up Cam Wired. Search for Ring in one of the app stores below, or
More informationNAVIGATOR Product demonstration prop building instructions
NAVIGATOR Product demonstration prop building instructions Regional competitions may build product demonstration props out of materials other than PVC pipe. Your regional coordinator will inform you of
More informationInstructions. Table of Contents
Instructions Table of Contents Hardware and Controls... Base station front face... 4 Side panel... 6 Fencer pack... 7 Radio link and sync process... How to sync packs to the base station... 8 Radio channel...
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO AND TANDEM KAYAKS IMPORTANT: For Tandem kayaks, the Supplemental Kit will be needed in addition to this kit and can be purchased through a registered dealer. The addition of a rudder to
More informationPART NUMBER: E361SXA200 DESCRIPTION: KAYAK CARRIER
A KIT CONTENTS: : Plug 16x Long Carriage Bolt 4x Hex Key 4x Button Head Screw 4x Pad Strap BASE Over-Molded Wrench 1x SnapAround 4x 1/5 : Important Notes: Minimum crossbar spread of 24". If spread is less
More information1. Set up your Stick Up Cam Wired.
Stick Up Cam Wired 1. Set up your Stick Up Cam Wired. Download the Ring app. The app walks you through setting up and managing your Stick Up Cam Wired. Search for Ring in one of the app stores below, or
More informationInstallation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No
Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION
More informationAegea Assembly Notes:
Aegea Assembly Notes: The Aegea model is a thermal Duration (TD) model made up of components from Phil Barnes 1 (bagged wing and tail group) and Terry Luckenback 2 (Pretty Mantis fuse). Due to its construction
More informationIMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION
IMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION This Fitting Guide is designed to assist in the Installation of your Reverse Osmosis System. Some of the parts that are supplied with each system may
More informationReproduction. Not for. Installation Instructions. Installation Instructions. Part No Installation. 32/36 Bagger 32/36 Kit WARNING
Installation Instructions Installation Instructions 32/36 agger 32/36 Kit Part No. 5600268 its 32/36 Mowers Kit ontents Part No. Qty. escription Part No. Qty. escription 5404389 1 Weld, agger Mount, 32/36
More informationMANDATORY BULLETIN No.: SAFETY RELATED. EV a SR. Appendix 1 Bulletin Flow Chart
Appendix 1 Bulletin Flow Chart Form No.: QS-406/F-03A Issue: Date of Issue: Page: 2 APPENDIX 2 Inspection of Nicopress Pressing Tooling: Vernier calliper or Nicopress check gauge Felt-tip pen to mark clamps
More informationAT Kelly Torso. Directions for Use
AT Kelly Torso Directions for Use 260-00001 2 Table of Contents Recommends 4 Items Included 5 Skills Taught 5 Preparing the Manikin for Use 6 Head 6 Lungs 6 Abdominal Thrust 6 Instructions for Use 6 Airway
More informationPaddle Bar Replacement
This procedure is to help facilitate the replacement of the 23 Paddle Bar Assembly on the ANKOM Dietary Fiber Analyzer. Note: The following items will be sent in a replacement package as part of the 23
More informationDescription Length Width Thickness Max. Bundle Tensile Strength Screw Size Qty./Bag Cat. No.
Mounting Head Ties Natural & UV Black Cable Ties Secures and positions wire bundles, cables, hoses, etc. to panels or other surfaces with one fastener to reduce time and cost Allows bundling before and
More informationInstallation Instructions - Steel 4 Spring Arm Kits , , , ,
Installation Instructions - Steel Spring Arm Kits 50-0709, 50-079, 50-0750, 50-075, 50-078 GR 8// 07-00 0 N. Marshall Ave. El Cajon CA. 900 For technical support call us at (800) 8-075 Step. Determining
More informationTABLE OF CONTENTS nrs.com
OWNER S MANUAL TABLE OF CONTENTS Assembly...3 Valves...4 Maintenance and Cleaning...4 Boat Repair...5 Transport...5 Storage...6 Limited Warranty...6 Congratulations! Your NRS GigBob is ready to carry you
More informationWildcat LB Winch Kit. Operator s Manual Installation Instructions Replacement Parts List. With Wireless Control System.
p/n 2259-560 Wildcat 4000 LB Winch Kit With Wireless Control System Operator s Manual Installation Instructions Replacement Parts List 2012 Arctic Cat Inc. Trademarks of Arctic Cat Inc. Thief River Falls,
More informationStick Up Cam Wired. 02_Stick_Up_Cam_Wired_MANUAL_ANZ.indd 1
Stick Up Cam Wired 02_Stick_Up_Cam_Wired_MANUAL_ANZ.indd 1 10/16/18 1:05 PM 1. Set up your Stick Up Cam Wired. Download the Ring app. The app walks you through setting up and managing your Stick Up Cam
More informationBR-2444 ROWING MACHINE
BR-2444 ROWING MACHINE Important Safety Information Please keep this manual in a safe place for reference. 1. It is important to read this entire manual before assembling and using the equipment. Safe
More informationEt's Skeg: the full story
Et's Skeg: the full story Having used pie-slice skegs on mass-market boats with big floppy slots and finding them ok, but not ideal, I researched a bit online looking for a skeg or skeg design for my North
More informationPIVOT SHUTTLE Dropper Post Cable Housing Replacement Maintenance Procedure
PIVOT SHUTTLE Maintenance Procedure This maintenance guide provides detailed instructions to replace the dropper post cable housing on the Pivot Shuttle should something malfuction or break. If these steps
More informationPARTS - FORWARD. Kayaking + Fishing Parts & Accessories Hook HATCH SEAL "TRIM-LOC" (TOP MOLDED) 5 REQ
PARTS - FORWARD 72104001 Hook 71301001 HATCH SEAL "TRIM-LOC" (TOP MOLDED) 5 REQ 71302001 HULL FLANGE SEAL (pre 2012 ADV) "TRIM-LOC" (SIDE GLUED) 5 REQ 80012001 Pedal Retainer Bungee w/ Hook 84560001 Mast
More informationEZ-Mount 4 Spring Enclosed System to 22 (Low & High Mount Applications) Installation Instructions
501-1768 (With Wire) 501-1769 (No Wire) 501-1766 (With Wire) 501-1767 (No Wire) 607-015 WLH 06/20/18 TABLE OF CONTENTS ***Assembly*** ***Parts*** Pivot Points and Mounting Locations (Low Mount)... 1 High
More informationSails. Sails: extract from 'Super-detailing the Cutter Sherbourne' page 1 George Bandurek
Sails There are many arguments for adding or omitting the sails on a model ship. There is no right answer and I decided to have a combination of set and furled sails on my model of HM cutter Sherbourne
More informationwalk with independence
walk with independence Lightweight www.novamedicalproducts.com WARNING Failure to follow any or all safety instructions may result in serious injury or death. adjustment and usage yourself or ambulate
More information