Access Dinghy. Electrics. Installation. Manual
|
|
- Edmund Clarke
- 5 years ago
- Views:
Transcription
1 Access Dinghy Electrics Installation Manual SA1.e May, 00
2 ELECTRICS INSTALLATION MANUAL 1. Mark (using old cutout) and drill a pilot hole as the centre for inspection port in the starboard or right side arm rest. Position the port towards the front allowing 20mm clearance in front and above the port. 4. Drill pilot hole middle of rear of right armrest for the joystick cable, then drill out with 35mm holesaw. 2. Cut out hole for inspection port using a 140mm holesaw. 5. In the top of the console 130mm behind the aft edge of the mast, mark and drill pilot hole and cut out with undersized 1 holesaw for the main sheet deck grommet. Knock the grommet in place with a piece of pine. 3. Drill pilot hole in centre of right side front seat tube recess, then drill out with 29mm holesaw. SA1.e May, 00
3 6. Mark with texta or chinagraph pencil the centres for the helm winch and its locating bolt. Use the plastic jig held against the aft bulkhead and align with the aft inspection port. Carefully drill both holes with 6mm bit. Bore out the upper of thbe two holes with an undersized 1 holesaw. 7. Pre fit the helm motor, use rattail and half round files to enlarge the holes as necessary. 8. Fit the helm motor using shortened 6mm x 12mm long round head metal thread with large washer. 9. Drill and pop rivet a saddle holding a plastic hook above the aft inspection port to hold the helm winch power cable. 10. Drill and pop rivet a saddle under the arm rest to attach the control box. 11. Fit the sheet winch by supporting it in place using the mainsheet (8m long 6mm Double Braid red fleck), pull it as far aft as possible, and using the right angle air drill, drill the 4 x 6mm locating screw holes. SA1.e May, 00
4 12. Fit the control box and its cables and hook up the battery, motors and joystick. 13. Fit the helm winch drum, reeve a cord through the blocks past the drum and rottate the drum lock to lock to determine its centre, then drill 6mm holes to attach the 2 halves of the steering line. 14. Attach a rudder box, and align the rudder, helm winch drum and joystick on the centreline, and fit and lightly tension the steering lines. 15. Work the joystick to operate the winches to determine if the rotation is correct, and if not reverse the polarity at the winches. SA1.e May, 00
5 16. Prepare the right side seat front tube with a groove and shorten to allow for a second locking ring. 17. Prepare the rubber bungs. The 35mm single hole needs to be drilled out before being split, while the 2 hole bung needs to be split to the holes on opposite sides. 18. If polarity/rotation correct remove the whole system and spray all corradable parts with Corrosion Guard. 19. When dry/tacky, tape up the motors and batteries and refit the whole system. 20. Drill,3M, and pop rivet in place the inspection port. 21. Fit a 2m traveller with tandem traveller block. 22. Use rectangles of soft flexible foam to wedge the battery and sheet winch cables elevated and clear of the cockpit floor. 23 Attach to the joystick a servo assist warning notice and ensure the how to instructions are included in the boats sail bag. NB. A) Ensure the control box has been sealed around the cable outlets, inside and lid, screwed down with ½ S/S self tappers with attached plastic hook using 300mm cable tie and pulled tight. B) Preparation of Joysticks. The joystick holders are layed up with grey pigmented resin, layup being tissue, 1 x 225gm csm with 3 x 450 csm strips around the edges. After the joystick fitted the cable is glued into a prepared slot with grey Sikaflex, and a 50mm length of 15mm diameter near solid tube is rounded and fitted to the joystick, packed using 3 turns of masking tape. C) Preparation of sheet winch. Using fine artist brush apply fast resin to the turned groove in the winch drum and liberally sprinkle treated glass spheres. Fit the drum when resin has cured. Shape and fit the polyethylene rope guide and support, then thread the 8m x 6mm red fleck double braid. Widen the attaching tabs a little and re-tap the 6mm threads. D) Preparation of helm winch. It should be ready to fit. SA1.e May, 00
6 Servo Assist Electrics Operations Manual CONTENTS How to operate the Servo Assist Dinghy 2 Maintenance and Troubleshooting 3 The Components 4
7 How to operate the Servo Assist Access Dinghy ABOUT THE SYSTEM The Servo Assist Access Dinghy can be sailed both manually and controlled by a variety of joysticks and switches. The basic unit has sheet and helm winches operated by a 4 way joystick, push forward for sail out, back is sail in, steer left is push joystick left and right, push to right. This standard joystick is typically strapped around the chest and moved by hand, but can be up high and worked with the chin. There is also the option of a paddle switch with very large flaps which activate micro switches. The unit is fully adjustable and mountable in any position, sliding on plastic tubes, held in place by suction cups. Many people have difficulty with fine finger control, the paddle switch can be bumped with the wrist or foot giving very precise commands for both winches. There is also the option a 4 way joystick mounted on a small box which will suit some applications. It too is located and held in place with plastic tubes and suction cups similar to the paddle switch above. We advise the most electrically inclined club member to take a close interest in the servo assist boat and to maintain it. Remove the electrics now to see how it works. All the parts are easily removed and a set of bungs are supplied to seal up all holes. Remove them regularly and spray with water inhibitor. If the electrics are seldom used don t leave them in the boat to corrode. Inside the control box is a 10amp-12volt fuse which protects the circuitry if the sheet winch is stalled and overloaded. If the sheet winch fails to work when activated this could be the cause. See maintenance and troubleshooting.
8 MAINTENANCE AND TROUBLESHOOTING. This equipment has to be serviced regularly if it is to remain free of corrosion and serviceable. Prior to leaving our factory all terminals, plugs and corrodable parts were sprayed with Corrosion Guard, a spray can of which is supplied. We advise you to spray all exposed terminals regularly, and inspect all the electrical components regularly, noting and treating any signs of corrosion. Spray Corrosion Guard directly into all plugs and wipe off excess from non corrodable areas. Also: 1. Do not allow any leads and plug ends to remain immersed in water. 2. If components are swamped spray them with Corrosion Guard soon after. Remove and dry them first if necessary. 3. Appoint a handy, practical volunteer to take charge of the electrics, ideally someone with an electrical background. 4. Remove the inspection ports to ventilate the buoyancy compartment when the boat is packed away each day. 5. When the boat is stored for extended periods, remove (all) the electrics completely, service them and store in a dry place. 6. If the boat is usually sailed manually, remove the electrics till they are needed again, closing all the holes with the rubber bungs provided. 7. If the sheet winch fails to work when activated first check the plug leads if all seems OK next listen at the control box to hear if the relays are clicking. If they are the problem may be the blow fuse inside the control box which is in the circuit to protect the components if the sheet winch motor is stalled and overloaded. N Open the box and fit a new 10amp-12volt fuse. Reseal the control box lid with urethane rubber preferably. These Recommendations should be taken very seriously and apply to any environment, but the warmer and more humid your climate the more vigilant you will have to be. IF YOU SAIL IN SALT WATER YOU SHOULD TAKE THESE RECOMMENDATIONS VERY SERIOUSLY.
9 THE COMPONENTS 1. The boom comes fitted with a sheet for manual use. When the Electric sheet winch is used remove the manual sheet from the boom and reeve the servo assist sheet as a two part only through the block on the traveller with the dead end tied off with a bowline at the block at the boom end. 2. Leave the traveller very long, adjust its length so the mast wont be over bent if the sheet is over tensioned. 3. The control box is very simple with 4 relays controlling the 4 functions. The box is suspended under the right arm rest. The battery lead and sheet winch lead run forward and pass through the right lower seat tubes. A simple 2 hole rubber bung acts as the seal.
10 4. The sheet winch lead is held up under the console with a small block of foam. Remove the sheet winch and check its workings. The 8mm allthread can be turned by screwdriver to adjust tension as the rope wears. 5. The helm winch and joystick leads run aft from the control box. The helm winch can be removed through the inspection port. The helm winch lead hangs on a hook above the aft inspection port which keeps it above any water. 6. Adjust the steering lines at the joystick and at the tiller to centralise the steering when needed. Keep it on the tight side.
11 7. The joystick lead and plug can pass through the seat under the tube to keep them out of any water. 8. There are two 12 volt gel batteries. They will run the boat all day and should be charged after every days use. The batteries are lead acid and don t need to be run down. Never run them down. Keep them charged. The charger will trickle charge over night. Ideally charge one battery at a time. 9. If there is no battery charger supplied (if you are in a 110 Volt area) acquire a 12 (or 14.4 Volt) 1/3 or 1/2 amp plug pack trickle charger suitable for gel lead acid batteries, from Tandy, Radio Shack, West Marine or similar. We can provide a plug on a short lead to adapt your charger to the battery lead. Always keep the batteries charged. Never let them discharge completely.
Bladerider X8 Assembly Help Notes
2.1 Remove All Parts & Have Some Tools Handy Remove all items from the box and identify each part as per the packing sheet and check that nothing is missing. If there is something missing, please email
More informationAccess Dinghies LIBERTY OPERATIONS & SAFETY MANUAL. Page 1
Access Dinghies OPERATIONS & SAFETY MANUAL LIBERTY Page 1 Items included with your Liberty 1. Liberty 11. Foresail (Jib) 2. Main Mast 12. Bobbin 3. Fore Mast 13. Mainsheet 4. Boom 14. Outhaul 5. Centreboard
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationHansa 2.3 Rigging Guide
Hansa 2.3 Rigging Guide Manufactured by Hansa Sailing Systems Pty Ltd ABN 56 079 318 031 4/4 Cumberland Avenue SOUTH NOWRA NSW 2541 AUSTRALIA Postal: PO Box 5048 NOWRA DC NSW 2541 Telephone: +61 2 4403
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO KAYAKS IMPORTANT: Tandem models will require the Wildy Supplemental kit in addition to this kit. The Supplemental kit provides extension straps and extra footbraces that allow rudder positioning
More informationSEADUCER BOATS GAS SPORT HYDRO
SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO AND TANDEM KAYAKS IMPORTANT: For Tandem kayaks, the Supplemental Kit will be needed in addition to this kit and can be purchased through a registered dealer. The addition of a rudder to
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationOPPI Rigging Guide 3/2008
OPPI Rigging Guide 3/2008 McLaughlin Boat Works optistuff.com Thanks for purchasing OPPI, the most durable and F-U-N sailboat available. Rigging your OPPI is easy and the following pictures make it a breeze
More informationFitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No
Fitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No. 41 130 This single line reefing kit allows reefing control lines to be led aft to the safety of the cockpit.
More informationULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS
ULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS TOOLS NEEDED: DRILL ¼ DRILL BIT ¾ HOLE SAW 3/16 DRILL BIT PHILLIPS HEAD SCREWDRIVER 7/16 WRENCH HEAT SOURCE: PROPANE TORCH, LIGHTER OR HOT AIR GUN WIRE CUTTER
More informationMethylethycetone (MEC) - PMS 60 polyurethane glue - Grease - White silicone
CHAPTER PLAN page : 1/8 SAILING BOAT SUSPENDED WITHOUT DECK BEARING SAILING BOAT SUSPENDED WITH DECK BEARING SAILING BOAT SUSPENDED WITH AUTOMATIC BEARING ALIGNMENT RUDDER SYSTEM FOR ANTARES MOTOR BOAT
More informationCarbo Racing Foil Instruction Manual Unit 0, 1, 2, 3
Carbo Racing Foil Instruction Manual Unit 0, 1, 2, 3 WARNING!: Strictly follow all instructions to avoid an accident, damage to your vessel, personal injury or death. See www.harken.com/manuals for additional
More informationSEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
More informationTable of content Introduction 5 1. Part 1. Assembly Tools needed for Assembly Glossary Hulls Mounting the beams 7
Table of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Placing the
More informationTHUNDER INSTRUCTIONS A LMOST READY TO SAIL MODEL YACHT
THUNDER INSTRUCTIONS A LMOST READY TO SAIL MODEL YACHT Long: 1000mm High:1890mm Toatl sail area: 0.4 m2 1 MODEL YACHT ASSEMBLY INSTRUCTIONS & SAILING HINTS Thank you for purchasing one of our range of
More informationANGEL INSTRUCTIONS ALMOST READY TO SAIL MODEL YACHT
ANGEL INSTRUCTIONS ALMOST READY TO SAIL MODEL YACHT Long: 920mm High:1840mm Toatl sail area: 0.4 m2 1 MODEL YACHT ASSEMBLY INSTRUCTIONS & SAILING HINTS Thank you for purchasing one of our range of model
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More informationFDR CHRYSLER 16' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange
Page of 6 Revised 2/0/76 RIGGING INSTRUCTIONS FDR CHRYSLER 6' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange to the new owner, or the new owner is
More informationRef Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
More informationChapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum
Chapter 2 Rigging Cutting Wire Rope The wire rope must be tightly seized on both sides of the point where the wire rope will be cut, as shown in Figure 2-1. Seize the wire rope with either seizing wire
More informationWIND CLIPPER KTS ILLUM SCALE INC DEC CLIPPER WIND SYSTEM
CLIPPER WIND KTS ILLUM SCALE DEC INC CLIPPER WIND SYSTEM TABLE OF CONTENTS INTRODUCTION PRE-TEST OF INSTRUMENT INSTALLING THE MASTHEAD SENSOR UNIT INSTALLING THE DISPLAY NORMAL OPERATION CHANGING THE
More informationA Basic Guide to Europe Dinghy Rigging
The Basics: A Basic Guide to Europe Dinghy Rigging Use the smallest blocks available for the line size. Most of the blocks on your boat will be micro blocks. Examine all of your rigging and ensure that
More informationCOASTAL IN-BOOM FURLING SYSTEM. Installation Manual
COASTAL IN-BOOM FURLING SYSTEM Installation Manual 1 TABLE OF CONTENTS Page Number 3. Disclaimer 4. Components packing list & required tools 5. Gooseneck bracket location 6. Installation sail track 7.
More informationRUDDER KIT INSTRUCTIONS
C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,
More informationFar East Boat Optimist Rigging Instructions
Far East Boat Optimist Rigging Instructions These instructions are written specifically for Far East Boats Championship and Racing Optimist. Parts of the Optimist PAGE 1 Sprit Wind Indicator Sail Mast
More informationCHAPTER 5 REWIND STARTERS
GENERAL INFORMATION CHAPTER 5 REWIND S Rewind starters used on vertical shaft Tecumseh engines are top mount horizontal pull style or side mount vertical pull style. Horizontal shaft engines use side mounted
More informationRUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More information2. Note that the ropes from the rigging board are secured in the cam cleats of the jib fairleads.
VII 1. Place the hull, bow into wind, on its trailer, a soft surface, or a rigging board. We strongly recommend making a rigging board; it is simple and inexpensive and greatly simplifies rigging and working
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More information1 Tuning Platform Reseating Beam Pads Rudder alignment Noisy Foils Rig Tension...
Contents 1 Tuning... 2 1.1 Platform... 2 1.2 Reseating Beam Pads... 2 1.3 Rudder alignment... 3 1.4 Noisy Foils... 3 1.5 Rig Tension... 4 1.6 Mast rake... 4 1.7 Spreader rake... 5 1.8 Diamond tension...
More informationDRAGONFLITE 95 RESTRICTED CLASS RULES 2016
DragonFlite Force 95, Restricted Class Rules 2016 2013 Version 1.0 DRAGONFLITE 95 RESTRICTED CLASS RULES 2016 Version 1.0 DF Racing Rules Committee 2016 Introduction The DragonFlite 95 (DF95) project started
More informationBelow are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
More informationE-trike Li Assembly Guide
PREPARATION 1. Read this assembly manual BEFORE commencing assembly. 2. Carefully remove all the components and packaged hardware from the shipping boxes. 3. Unpack the contents of the large double box
More informationTable of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Mounting
More informationProgression 24LD Stern Drive
Progression 24LD Stern Drive This list is provided to help you to evaluate the many advantages that come STANDARD with a PROGRESSION 24LD. As you compare Progression s many superior features to the competition,
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationInstruction Manual. Features. Specification: Length: 730mm Width: 500mm Height: 1000mm Sail Area: 0.15m 2. Weight: 692g (w/o battery & receiver)
AN UNBELIEVABLE SPEED MACHINE Instruction Manual Features Specification: Length: 730mm Width: 500mm Height: 1000mm Sail Area: 0.15m 2 Weight: 692g (w/o battery & receiver) Thank you for purchasing your
More informationINTERNATIONAL SUNFISH CLASS ORGANIZATION CLASS RULES
INTERNATIONAL SUNFISH CLASS ORGANIZATION November 2017 CLASS RULES 1. GENERAL The design and development of the Sunfish sailboat was directed to the creation of a one-design class where the true test is
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More informationInstalling a Tiller Pilot on a Double Ended Yacht
Installing a Tiller Pilot on a Double Ended Yacht My Frances 26, Tom Thumb is a classic yacht with a double ended (canoe) stern. I found it difficult to install a tiller pilot (a Raymarine ST1000+) as
More informationTECH SHEET ORANGE PIVOT TOOL INSTRUCTIONS
page 1 ORANGE PIVOT TOOL INSTRUCTIONS This is a guide of how to change the pivot bearings on an Orange frame with a bore style pivot axle. 4 8 Bore Type Pivot Axle Horiz-Hold Type Pivot Axle Please read
More informationM32 CATAMARAN ASSEMBLY MANUAL
M32 CATAMARAN ASSEMBLY MANUAL 1 M32 CATAMARAN ASSEMBLY MANUAL MANUAL SUMMARY M32 ASSEMBLY Parts and tools Instructions MAST PLATFORM Parts and tools Instructions MAST STEPPING Instructions MAIN HALYARD
More informationInstallation Instructions - Steel 4 Spring Arm Kits , , , ,
Installation Instructions - Steel Spring Arm Kits 50-0709, 50-079, 50-0750, 50-075, 50-078 GR 8// 07-00 0 N. Marshall Ave. El Cajon CA. 900 For technical support call us at (800) 8-075 Step. Determining
More informationIn each step, the needed parts are shown the number right below. Locate all parts for the step.
Tools Required for Assembly Phillips Screwdriver, Med Needle Nose Pliers Sandpaper (#400 grit) Hobby Knife Scissors CA Instant Glue Rubbing Alcohol Drill Bit 1/16", 1.6mm 5/64, 2mm 1/8, 3mm 5/32, 4mm Before
More informationAssembly Instructions Star Kayak Sails kit to a Hobie Mirage drive kayak.
Assembly Instructions Star Kayak Sails kit to a Hobie Mirage drive kayak. 1. Remove packaging lay out contents. Separate the plastic tubes from the aluminium tubes. 3 plastic and 4 aluminium. ( Giant Star
More informationKari-Tek. Kari-Tek. Hydro Skeg Retro-Fitting Instructions. Instructions for retro-fitting of Hydro Skeg
Kari-Tek Instructions for retro-fitting of Hydro Skeg A good knowledge of fibreglassing will be required to fit the Hydro Skeg successfully. When working with fibreglass and cutting the holes, safety glasses,
More informationSetup Guide for your HVO Naked Drone
Setup Guide for your HVO 60 + 60 Naked Drone 1 The Big Picture 1. Choose The System Location 2. Get the Power Ready 3. Get an Approved Oxygen Regulator 4. Get the Tools You ll Need 5. Unpack the crate
More informationGRI-1300/1350Li. User Manual
User Manual GRI-1300/1350Li Your Cart Tek caddy cart was thoroughly quality control checked and road tested before being shipped to your address. We do everything possible to assure that your caddy is
More informationSanibel Owners Manual
Sanibel 36-600 Owners Manual TM Specifications Length (Hull):... 36 inches Height (Mast):... 51.5 inches Height (Overall):... 69 inches Beam:... 7.5 inches Radio: JR Beat Gear w/sail winch servo Sail area:
More informationINSTRUCTIONS FOR THE 7FT REVOLVER 3-IN-1 MULTIGAMES TABLE
INSTRUCTIONS FOR THE 7FT REVOLVER 3-IN-1 MULTIGAMES TABLE Please keep these instructions for future reference. Adult assembly required. This table is not a toy & is intended for use by or under the supervision
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationTrogear Bowsprit Through Hull Installation Manual
Trogear Marine Products, LLC www.trogear.com info@trogear.com 866-616-2978 Trogear Bowsprit Through Hull Installation Manual Congratulations on your purchase of the Trogear Bowsprit which can be installed
More informationDrawn up by: / RK Revision: 01 Reviewed: Page: 1 of 23 HI-SR 540 USA. Operating instruction SR 540 Face Shield
Page: 1 of 23 Operating instruction SR 540 Face Shield Page: 2 of 23 General information The SR 540 Face Shield can be used together with the SR 500 Powered Air-Purifying Respirator system of components
More information222 Schwinn Recumbent Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions
222 Schwinn Recumbent Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions FITNESS SAFEGUARDS AND WARNINGS Before starting any exercise program, consult with your
More informationINSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
More informationPARTS - FORWARD. Kayaking + Fishing Parts & Accessories Hook HATCH SEAL "TRIM-LOC" (TOP MOLDED) 5 REQ
PARTS - FORWARD 72104001 Hook 71301001 HATCH SEAL "TRIM-LOC" (TOP MOLDED) 5 REQ 71302001 HULL FLANGE SEAL (pre 2012 ADV) "TRIM-LOC" (SIDE GLUED) 5 REQ 80012001 Pedal Retainer Bungee w/ Hook 84560001 Mast
More informationThank you for purchasing your new Empire Reloader B Sound-Activated 3-Speed Paintball Hopper!
Thank you for purchasing your new Empire Reloader B Sound-Activated 3-Speed Paintball Hopper! Should you require any technical assistance on the use of this product, or if your product needs servicing,
More informationStep 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.
WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the
More informationNo.5550 INTRUCTION MANUAL WARRANTY WARNING. Notice This is not a toy. Assembly and operating of this boat requires adult supervision.
INTRUCTION MANUAL WARRANTY Thunder Tiger guarantees this model kit to be free from defects in both material and workmanship. The total monetary value under warrant will in no case exceed the cost of the
More information2019 MADONE ASSEMBLY MANUAL
2019 MADONE ASSEMBLY MANUAL 2019 MADONE Rim brakes and Di2 drivetrain Rim brakes and mechanical drivetrain Disc brakes and Di2 drivetrain Disc brakes and mechanical drivetrain TABLE OF CONTENTS Common
More informationaero naut Order No. 3009/00
aero naut Order No. 3009/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually numbered.
More informationMount the actuator in the bracket provided and install a 24-foot EFTC cable to the actuator.
. Mount the actuator in the bracket provided and install a 4-foot EFTC cable to the actuator. Route the cable through left stanchions,, and 4. Be sure that the cable does not contact any spring or push
More informationE Manual Self tacking system 30
597-205-E 2015-12-09 Manual Self tacking system 30 1 Self tacking system 30, 443-200-10 A self-tacking jib makes life on board a lot easier, in particular for shorthanded crews. The jib sheet is led to
More informationAdvancedTrak Rudder Kit AE4005. Assembly and Installation Instructions
AdvancedTrak Rudder Kit AE4005 Assembly and Installation Instructions Thank you for your purchase of the Advanced Elements AdvancedTrak Rudder Kit! A Kayak Rudder is a great way to enhance the tracking
More informationAn Australian Classic by spectre.com
An Australian Classic by www.go spectre.com Your Bug! Welcome to the Balain Bug experience!!!!!! The Bug kit has been designed so as to be a modern version of the Traditional Bug now you can sail like
More informationF-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME
F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10: TAILCONE F-1279-L UPPER LEFT
More informationRemember that you must check your boat before every outing. Visual check of the general condition of the shoes, stretcher, etc.
Heel Restraints Visual check of the general condition of the shoes, stretcher, etc. Each heel to be restrained to prevent it from rising higher than 7cm, as measured at right angles from the footplate.
More informationTugster. Tug Boat. Competition or Sport Tug Kit. A Zippkits R/C Boat. Building Instructions
Z I P P M A N U FA C T U R I N G Tugster Tug Boat Competition or Sport Tug Kit A Zippkits R/C Boat Building Instructions 2016 JMP Hobby Group St. Paul, Indiana 47272 www.zippkits.com Toll Free (866) 922-ZIPP
More informationWysiwig - Wayfarer Rigging Guide
Wysiwig - Wayfarer 8767 - Rigging Guide GENERAL NOTES Before you go afloat, make sure that the self-bailer is closed. It is operated through the cut-out in the starboard floorboard. If you do not close
More informationFitting Instructions For Slab Reefing Kit Part No For Yachts Up To 8.5m (2 Reefing Points)
Fitting Instructions For Slab Reefing Kit Part No 41483 For Yachts Up To 8.5m (2 Reefing Points) This system makes reefing your mainsail a quick and easy operation. Just lower the mainsail just below a
More informationPOWER ASSISTED BICYCLES OWNERS MANUAL
POWER ASSISTED BICYCLES OWNERS MANUAL WE HAVE INCLUDED A BICYCLE OWNER S MANUAL WHICH YOU SHOULD REFER TO FOR ALL GENERAL CYCLE MAINTENANCE. CONTENTS Page. 3 Unpacking. Page. 3-4 Easy steps to get started.
More informationInstallation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems , ,
Installation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems - 204-025, 206-025, 22-025 NB /0/ 607-0020 404 N. Marshall Ave. El Cajon CA. 92020 For technical support
More informationANGEL 2000 glider ARF ASSEMBLY MANUAL. Specifications: MS: 129
WWW.SEAGULLMODELS.COM ASSEMBLY MANUAL ANGEL 2000 glider Graphics and specifications may change without notice. MS: 129 ARF Specifications: Wingspan---------------78.7 in ( 200cm). Wing area---------------582.8sq.in
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More informationHOW-TO: Install a Wildcat Lighting System
Items needed: Acetone Isopropyl Alcohol Power Drill 8 zip ties Marine Goop 9/6 Drill Bit /6 Drill Bit Pencil or dry erase marker Measuring tape Extra wire Extra Grey Wire nuts Wire cutters Wire Strippers
More informationTopaz OMEGA Rigging Instructions
Topaz OMEGA Rigging Instructions www.toppersailboats.com TOPAZ OMEGA RIGGING INSTRUCTIONS CONTENTS 02. Introduction 02. Manufacturers Details 03. Maintenance 04. Raising the Mast 05. Attaching the Boom
More informationPico rigging manual 2007.doc Page 1 of 28
Pico rigging manual 2007.doc Page 1 of 28 Pico Rigging Instructions The Pico rigging instructions are a guide to rigging your boat. Due to production supplies certain parts may be slightly modified from
More informationInstallation Instructions
116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting
More information3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO
NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationHALYARD EXITS, CLEATS, CLUTCHES, WINCH PADS, HANDLE POCKET
HALYARD EXITS, CLEATS, CLUTCHES, WINCH PADS, HANDLE POCKET 1(6) General CNC-milled masts Cut out using templates Cut out without using templates Assembly Assembly clutch spinnlock ZS/1214 Check point General
More informationFor ANCHOR WINCH Model: T Big Water 45 T sw Salt Water Series Big Water 45
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ANCHOR WINCH Model: T10110-45 Big Water 45 T10103-45sw Salt Water Series Big Water 45 If you have any questions or difficulty installing this
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More informationSPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.
2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or
More informationSECTION 10iS: TAILCONE
VAN'S AIRCRAFT, INC. F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10iS: TAILCONE
More informationVERTICAL AIR COMPRESSORS
VERTICAL AIR COMPRESSORS MODEL NO: VE15C150, VE18C150, VE25C150 PART NO: 2226010, 2226020, 2226025 OPERATION & MAINTENANCE INSTRUCTIONS LS0715 INTRODUCTION Thank you for purchasing this CLARKE Vertical
More informationConstitution Instructions
Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel
More informationRef :MMHC14SR_GB Emetteur :MF Date :Dec 2014 Revision : 1 Page 1/18. ASSEMBLY MANUAL : HOBIE CAT 14 Std & Race HOBIE CAT 14 STD & RACE
Ref :MMHC14SR_GB Emetteur :MF Date :Dec 2014 Revision : 1 Page 1/18 HOBIE CAT 14 STD & RACE Ref :MMHC14SR_GB Emetteur :MF Date :Dec 2014 Revision : 1 Page 2/18 TABLE OF CONTENT Part list... 3 Ropes and
More informationATOC Meteorological Tower (6 meter-4 level) Guide
ATOC Meteorological Tower (6 meter-4 level) Guide SETUP Outline 1. Siting 2. Components 3. Transportation 4. The Tower 5. The Cables and Data Logger Siting Selecting an appropriate site for the weather
More informationCII Rigging suggestions
CII Rigging suggestions This mini-manual uses photographs of the final prototype sail and the final pre-production mast. Where changes occurred between these and the production units, they are described
More informationSoling Building Tips II
Soling Building Tips II Prepared: Arthur Deane Jan 20, 2002 adeane@ic.net Introduction The following are some lessons learned and experience gained in building a Soling kit. The plan developed is based
More informationEZ-Mount 4 Spring Enclosed System to 22 (Low & High Mount Applications) Installation Instructions
501-1768 (With Wire) 501-1769 (No Wire) 501-1766 (With Wire) 501-1767 (No Wire) 607-015 WLH 06/20/18 TABLE OF CONTENTS ***Assembly*** ***Parts*** Pivot Points and Mounting Locations (Low Mount)... 1 High
More informationC Crane. Installation & Operation Manual. SWL 120kg. The Hansa CRANE ID#: Davit ISO/DIS June 2000 Sling AS Sept 2000
The Hansa C Crane CRANE ID#: Installation & Operation Manual Ideal for the safe and dignified transference of sailors with disabilities from a wharf to the boat. The crane is also suited to many other
More informationFor ELECTRIC ANCHOR WINCH Models: T Pontoon 35 T sw Salt Water Series Coastal 35
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ELECTRIC ANCHOR WINCH Models: T10109-35 Pontoon 35 T10102-35sw Salt Water Series Coastal 35 If you have any questions or difficulty installing
More informationInstallation, Compensation and Maintenance Instructions for. RITCHIE Compasses. Made In U.S.A
Installation, Compensation and Maintenance Instructions for RITCHIE Compasses Made In U.S.A All Magnetic Compasses are vulnerable to magnetic interference, which will produce errors, called deviation.
More informationClub 420 Class Rigging Manual
Club 420 Class Rigging Manual Performance sailcraft 2000 Inc 2555 Dollard Lasalle, Quebec, H8N 3A9 Tel: 514 363 5050 email: info @ps2000.ca Website: www.ps2000.ca Mast set up Remove the pole and unwrap
More informationLITTLE TRI construction
LITTLE TRI construction I have built almost anything that can sail. At the age of 12 my first sail thing, an ice boat. I used skates which had to be mounted on shoes as runners. Big fun, very fast, only
More informationModel PSI Compressor with 3-Gallon Air Tank 12VDC
Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing
More information