OPTIMUM 700 BRATT PANS GAS & ELECTRIC BUILDER S SPECIFICATIONS. Part D: Maintenance instructions 3BE390838NM

Transcription

1 OPTIMUM 700 BRATT PANS GAS & ELECTRIC BUILDER S SPECIFICATIONS Part D: Maintenance instructions - WARRANTY - In order to guarantee this equipment, we recommend that you comply with the MANUFACTURER S INSTRUCTIONS in this manual. However if you can not undertake the required maintenance operations, our installation and service network is available to provide you with a personalized contract.. - WARNING - The product delivered to you complies with current standards. If any modifications are made the manufacturer cannot accept any responsibility whatsoever. The manufacturer can not be held responsible in the event of an incorrect use of the appliance. Keep your documents. 3BE390838NM

2 Page 1 3BE390838NM 01/12 CONTENT BRATT PANS GAS & ELECTRIC 1 ELECTRIC DIAGRAMS GAS BRATT PANS ELECTRIC BRATT PANS CHANGING COMPONENTS ACCESS TO THE COMPONENTS LOCATED BEHIND THE UPPER PANEL ACCESS TO THE COMPONENTS LOCATED BEHIND THE LOWER PANEL CHANGING AN APPLIANCE FROM ONE GAS TO ANOTHER LIST OF AUTHORISED GASES / PRESSURES AS PER CATEGORIES & COUNTRIES CHANGEOVER FROM A GAS TO ANOTHER GAS FLOW RATES AND POWERS CHART OF JETS and air adjustment LID ADJUSTMENT SPRING ADJUSTMENT ADJUSTMENT OF LID OPENING FRONT LINE PARTS GAS BRATT PANS ELECTRIC BRATT PANS...11

3 Page 2 3BE390838NM 01/12 1 ELECTRIC DIAGRAMS 1.1 GAS BRATT PANS BASIC DIAGRAM Well position Switch Safety indicator Regulation thermostat Regulation indicator Flame control box Energy trimmer Water control Cold water solenoid valve Hot water solenoid valve LIST OF PARTS Item Designation SA 30 Code Aa Flame control box Ar Energy doser Br Regulation thermostat Ebgr Ignitor electrode Hr Regulation indicator Hs Safety indicator S1 Switch water S2 Tank position switch Yec Hot water solenoid valve Yef Cold water solenoid valve Za Anti-interference relay

4 1.2 ELECTRIC BRATT PANS Page 3 3BE390838NM 01/ BASIC DIAGRAM MANUAL TILTING Heating contactor Safety thermostat Energy doser Regulation indicator Indicator voltage «On» Well position relay Water control Cold water solenoid valve Hot water solenoid valve POWER DIAGRAM 30 dm 2 BRATT PANS Three phase 230 Volts Three phase 400 Volts

5 Page 4 3BE390838NM 01/ NOMENCLATURE Item Designation SA 30 Code Am1 Ram control box Ar Energy doser Br Regulation thermostat Hr Regulation indicator Hma Indicator voltage On Kr Heating contactor M1 Tank tilting ram R 1300 Watts elements S1 Water control switch S2 Tank position switch Sd Push button: ram extends Sm Push button: ram retracts Yec Hot water solenoid valve Yef Cold water solenoid valve Za Condenser Zr Anti-interference relay

6 Page 5 3BE390838NM 01/12 2 CHANGING COMPONENTS 2.1 ACCESS TO THE COMPONENTS LOCATED BEHIND THE UPPER PANEL Open the lid and tilt the tank fully forward. - Undo the nuts on each inner side of the front top panel (see the diagram). - Unscrew both M5 x 16 screws under the facia. - Tilt the facia: Slightly pull downwards 1 then tilt it towards yourself ACCESS TO THE COMPONENTS LOCATED BEHIND THE LOWER PANEL Unscrew both M5 x 16 screws located under the lower panel. - To remove the panel: Slightly pull toward yourself 1 then downwards 2 and finally pull towards yourself again.

7 Page 6 3BE390838NM 01/12 3 CHANGING AN APPLIANCE FROM ONE GAS TO ANOTHER General: In the following chapters, the different gases are referenced as per their international codification: G20 G25 G30 G31 NATURAL GAS Group H. (Methane, Lacq gas) NATURAL GAS Group L. (Groningue type gas) BUTANE PROPANE 3.1 LIST OF AUTHORISED GASES / PRESSURES AS PER CATEGORIES & COUNTRIES Countries Category Gas Pressure (mbar) Austria - Switzerland II 2H3B/P G G 30 and G Sweden - Denmark I 2H G Finland I 3B/P G 30 / G Belgium G 20 / G 25 20/25 II 2E+3P G I 3+ G 30 / G /37 Germany II G 20 / G ELL3B/P G 30 / G I 3P G Ireland - United Kingdom G Greece - Switzerland II 2H3P G Portugal I 3+ G 30 / G /37 Italy I 2H G I 3+ G 30 / G /37 Spain G II 2H3P G or 50 I 3B/P G 30 / G France G 20 / G 25 20/25 II 2E+3B/P G 30 / G II 2E+3P G 20 / G 25 20/25 G 31 37/50 I 3+ G 30 / G /37 Luxemburg G II 2E3B/P G 30 / G II 2E3P G G I 3+ G 30 / G /37 Netherlands II 2L3B/P G G 30 / G II 2L3P G G Norway I 3B/P G 30 / G 31 30

8 3.2 CHANGEOVER FROM A GAS TO ANOTHER Page 7 3BE390838NM 01/12 Depending on the country of installation and the category of the appliance (indicated on the data plate), the change from a gas to another may require 2 operations: CI Change jets (main burner, pilot) (See paragraph 3.4) RA Adjustment of primary air (See paragraph 3.4) PROCEDURE: On the data plate, check: - The category(ies) of the equipment - The gas and pressure for which it is adjusted. In the following table, select: - the country in question - the gas and the category of the equipment (see above) - the gas and pressure for which the equipment is going to be set - Follow and carry out the necessary operations - Replace the gas data plate and fill in the box with the new gas used.

9 Page 8 3BE390838NM 01/12 COUNTRIES GAS OF ORIGIN NEW GAS OPERATIONS (or new gas) (or gas of origin) CATEGORY NECESSARY & Gas P(mbar) Gas P(mbar) AUTHORISED Austria G G 30 or G CI - RA II Switzerland G G H3B/P None Finland G G I 3B/P None Sweden - Danmark Belgium G G None II G 20 or G 25 20/25 G E+3P CI - RA G G I 3+ CI - RA Germany G G CI - RA G 20 or G G 30 or G II 2ELL3B/P CI - RA G G None G G I 3P CI G Change of G category (see *) Ireland - Portugal G G II 2H3P CI - RA United kingdom G G I 3+ CI - RA Greece - Switzerland Italy G G I 3+ CI - RA Spain G G 31 37/50 CI - RA II G G H3P CI - RA G G I 3B/P None France G 20 or G 25 20/25 G 30 or G CI - RA G G II 2E+3B/P None G G None G 20 or G 25 20/25 G 31 37/50 CI - RA II G G E+3P CI - RA G G I 3+ CI - RA Luxemburg G G 30 or G CI - RA II G G E3B/P None G G II 2E3P CI - RA G G I 3+ CI - RA Netherlands G G 30 or G CI - RA I G G L3B/P None G G II 2L3P CI - RA Norway G G I 3B/P None *Change of category to be undertaken only under our responsibility or that of our local agent GAS FLOW RATES AND POWERS See paragraph 1: TECHNICAL CHARACTERISTICS (Instructions for installation). 3.4 CHART OF JETS and air adjustment NOTE: - The burners referred to as "main burner" are simple tubes (BP: Main Burner). - The burners referred to as "secondary burner" are burners equipped with the interignition ramp (BS: Secondary Burner).

10 Page 9 3BE390838NM 01/12 Bratt pan 30 dm 2 GAS JETS Designation Pressure Type Qu Diameter d Code Family Type (mbar) burner (1/100 th ) (mm) Burner Natural G 20 / G / 25 BP gas BS G BP BS G 25*** 25 BP BS L.P.G. G 30 or G BP or 37 BS G 30 or G 31* 50 BP BS G 31** 50 BP BS Pilot Natural G 20 / G / gas G L.P.G. G 30 or G or or 37 or 50 * Configuration valid only for 50 mbar propane in Austria ** Configuration not valid in Austria *** Configuration valid only in Netherlands. RA: Air adjustment Air adjustment sleeve must be set to the dimensions given for d above. Pilot air adjustment (Valid for all models) Airflow can be adjusted using the collar that obstructs 1 of the two primary air holes. Collar

11 Page 10 3BE390838NM 01/12 4 LID ADJUSTMENT 4.1 SPRING ADJUSTMENT This adjustment enables to increase of diminish the strength for closing or opening the lid. - Remove the collector cover. - On the back part of the appliance, unscrew the blind nut to loosen the spring or tighten it to stretch it. Put the lid in open position to limit the strengths. Blind nut - Carry out this intervention on both springs and on both sides of the appliance. 4.2 ADJUSTMENT OF LID OPENING This adjustment enables to increase or diminish the opening angle of the lid. - Remove the collector cap. - Loosen the locking nut of the lid opening thrust. Screw or unscrew the adjustment screw to diminish or increase the lid opening angle and screw on the nut. The factory adjustment enables maximum opening of the lid. Adjustment screw Locking screw - Carry out this intervention on both sides of the appliances

12 Page 11 3BE390838NM 01/12 5 FRONT LINE PARTS 5.1 GAS BRATT PANS Designation Code Drilled and tapped bratt pan crank way 1 x 10 L/min solenoid valve V lever microswitch position switch c single pole thermostat Simmerstat Red indicator 230/400V, complete Green indicator 230/400V, complete Ignition electrode M µf condensor Ignition box and flame monitor Range flame pilot burner without nut Pilot flame nozzle diameter Pilot flame nozzle diameter Gas valve Pilot flame nozzle diameter Metal cage ball thrust bearing (mandatory) Draw spring with 30 x 200 diameter stainless steel insert ELECTRIC BRATT PANS Designation Code Drilled and tapped bratt pan crank way 1 x 10 L/min solenoid valve V lever microswitch Three-pole 25A 230V 50/60 Hz contactor Three-pole 32A 230V 50/60 Hz contactor position switch c single pole thermostat Simmerstat W element Green indicator 230/400V, complete µf condensor Metal cage ball thrust bearing (mandatory) Draw spring with 30 x 200 diameter stainless steel insert