EC-Type Examination Certificate

Transcription

1 6 DMT Translation (1) EC-Type Examination Certificate (2) - Directive 94/9/EC - Equipment and protective systems intended for use in potentially explosive atmospheres (3) DMT 02 ATEX E 029 X (4) Equipment: Stellungsregler Type Doc (5) Manufacturer: ABB Automation Products GmbH (6) Address: D Minden (7) The design and construction of this equipment and any acceptable variation thereto are specified in the schedule to this type examination certificate. (8) The certification body of Deutsche Montan Tcchnologie GmbH, notified body no in accordance with Article 9 of the Directive 94/9/EC of the European Parliament and the Council of 23 March 1994, certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equipment and pr otective systems intended for use in potentially explosive atmospheres, given in Annex IT to the Directive. The examination and test results are recorded in the test and assessment report BVS PP EG. (9) The Essential Health and Safety Requirements are assured by compliance with: EN 50014:1997 +A l -A2 EN 50018: 2000 General requi rement s Flameproof enclosure (10) If the sign "X" is placed after the certificate number, it indicates that the equipment is subject to special conditions for safe use specified in the schedule to this certificate. (11) This EC-Type Examination Certificate relates only to the design, examination and tests of the specified equipment in accordance to Directive 94/9/EC. Further requirements of the Directive apply to the manufacturing process and supply of this equipment. These arc not covered by this certificate (12) The marking of the equipment shall include the following: II 2G EEx d IIC T4ff5/T6 Deutsche Montan Technologie GmbH Essen, dated 31. January 2002 Signed: Di 11 Signed: E i C k h Off DMT-Certification body Head of special services unit page I of 2 to DMT 02 ATEX E 029 X This certificate may only be reproduced in its entirety and without cbanae Am Technologiepark I, Essen, Telefon (0201) , Telefax (0201)

2 6 DMT ( 13) Appendix to (14) EC-Type Examination Certificate DMT 02 ATEX E 029 X (15) 15.l Subject and type Positioncr type Doc Description The positioner is designed for the transmission of an electrical signal into a pneumatic signal. Certain variants of the electronics may be used intrinsically safe according to separate certification (sec 7.3). As pressure media neither flammable gases nor oxygen or oxygen enriched gases will be used Parameters l Electrical data Voltage Current :::'.AC/DC 30 v < 20 ma Pneumatic data Supply pressure ::: 6 bar Thermal data Temperature class Ambient temperature range -40 C :::'. Ta ::; T4 TS T6 85 C 80 C 65 C (16) Test and assessment report BVS PP EG as of31.0l.2002 ( 17) Special conditions for safe use 17.1 As per 4.3, the positioner is designed for use at an ambient temperature range of -40 C up to 85 C at maximum If the positioner is used at an ambient temperature above 60 C or below -20 C, cable entries and cable approved for a service temperature corresponding to the maximum ambient temperature increased by 10 K respectively corresponding to the minimum ambient temperature shall be used Variants which, according to separate certification, comply with type of protection intrinsic safety, shall not be used intrinsically safe once they have been used in type of protection flameproof enclosure. We confirm the correctness of the translation from the German original. In the case of arbitration only the German wording shall be valid and binding Essen, BVS-We/Mi A Deutsche Montan Technologie GmbH 12 1/) Head of special services unit page 2 of 2 to DMT 02 ATEX E 029 X This certificate may only be reproduced in its entirety and without change Am Tcchnologiepark l, Esson, Tclefon (0201) , Tclelluc. (0201)

3 Translation DMT 1st Supplement (Supplement in accordance with Directive 94/9/EC Annex III number 6) to the EC-Type Examination Certificate DMT 02 ATEX E 029 X Equipment: Manufacturer: Positioner type Doc ABB Automation Products GmbH Address: D Minden Description The positioner can be modified according to the descriptive documents as mentioned in the pertinent test and assessment report Test and assessment report BYS PP EG as of Deutsche Montan Technologie GmbH Essen, dated 11. July 2002 Jockers DMT-Certification body Eickhoff Head of special services unit We confirm the correctness of the translation from the German original. In the case of arbitration only the German wording shall be valid and binding Essen, BYS-We/Mi A Deutsche Montan Technologie GmbH Page I of I to DMT 02 A TEX E 029 X1N I This certificate may only be reproduced in its entirety and without change. Am Technologiepark I, Essen, Telefon (0201) , Telefax (0201)

4 ~ DMT Deutsche Montan Technologie GmbH Fachstelle tor Sicherheit elektrischer Betriebsmittel - Berg ba u-versuchsstrecke Prufprotokoll - Test and Assessment Report 1. Nachtrag - 1st Supplement BVS PP EG EG - Baumusterprufung fur Gerate und Komponenten zur Verwendung in explosionsgefahrdeten Bereichen (Richtlinie 94/9/EG) EC - Type Examination for Equipment and Components Intended for Use in Potentially Explosive Atmospheres (Directive 94/9/EC) AKKRfOITlfRUNG ,...:::= -= DAR-Reg.-Nr.: ZLS-P-359-2/01 Gegenstand: Gerat Typ Subject: Equipment type Hergestellt und zur PrOfung vargelegt Manufactured and submitted for examination An sch rift Address PrOfgrundlage Basis for verifications and tests Verwendete Narmen Standard basis Stellungsregler Typ Doc Positioner type Doc ABB Automation Products GmbH D Minden, SchillerstraBe 32 Anhang II der Richtlinie 94/9/EG Annex II of Directive 94/9/EC EN 50014: 1997+A1-A2 Allgemeine Bestimmungen General requirements EN 50018:2000 Druckfeste Kapselung Flameproof enclosure 'd' PrOfgrundlage for Sicherheits- und Gesundheitsanforderungen, die nicht van den verwendeten Narmen abgedeckt werden. Basis for those health and safety requirements not covered by the standard basis Schutzartkennzeichen Code for type of protection Entfallt Not relevant EEx d llc T4/T5/T6 Antragsnummer A Project number Seite 1 van 4 zum PrOfpratakall - Page I of 4 of Test Report Dieses PrUfprotokoll darf nur vollstilndig und unverandert vervielfaltigl werden This test and assessment repon may only be reproduced in its entirety and without change BVS PP EG I N1 Dinnendahlstral!.e 9 D Bochum Telefon-Phone 0201/ Telefax-Fax

5 4' DMT 1) Gegenstand und Typ Stellungsregler Typ Doc Subject and Type Positioner type Doc ) Beschreibung Alternativ werden die EinfOhrungsbohrungen geandert. Die Sintermetallscheibe 010 mm wird neu festgelegt. Description Alternatively, the entry threads are modified. The sinter disk 010 mm is re-defined. 3) Dokumentation - Descriptive Documents Zeichnung Nr. - Drawing No vom - dated / unterschrieben am - signed ) KenngroBen - Parameters Unverandert - Without change 5) Kennzeichnung - Marking Unverandert - Without change 6) StOckprufungen - Routine verifications and tests Unverandert - Without change 7) Auflagen/Bedingungen fur die sichere Anwendung - Special conditions for safe use Unverandert - Without change 8) Sicherheitstechnisch relevante lnformationen - Information relevant for safety Unverandert - Without change Bochum, den BVS-We/Mi A Deutsche Montan Technologie GmbH Fachstelle tor Sicherheit elektrischer Betriebsmittel Bergbau-Versuchsstrecke Der Sachverstandige The Testing Officer Seite 2 von 4 zum PrOfprotokoll - Page 2 of4 oftest Report BVS PP EG I N1 Dieses PrOfprotokoll darf nur vollstandig und unverandert vervielfaltigt werden This test and assessment report may only be reproduced in its entirety and without change

6 DMT Hinweis: Note: Der folgende Anhang bezieht sich nur auf die Bauartanderungen, die Gegenstand dieses Nachtrags sind. Er andert bzw. erganzt den entsprechenden Anhang des bestehenden PnJfberichts. The following annex is related only to the changes of the equipment which are subject for this supplement. It amends or supplements the respective annex of the existing test and assessment report. Anhang - Annex Protokoll Report Druckfeste Kapselung EN 50018:2000 Flameproof enclosure EN 50018:2000 (P/N1 -EN 50018) Seite 3 von 4 zum PrOfprotokoll - Page 3 of 4 of Test Report BVS PP EG I N1 Dieses Prufprotokoll dart nur vollstandig und unverllndert vervielflilligt werden This test and assessment report may only be reproduced in its cnllrcty and without change

7 A DMT Protokoll - Report Elektrische Betriebsmittel fur explosionsgetahrdete Bereiche Electrical Apparatus for potentially explosive atmospheres EN 50018: 2000 Druckfeste Kapselung,,d" Flameproof enclosure,,d" Teil II: Kommentare Part II: Comments 5.3 Gewindespalte Threaded joints Gewinde zwischen Thread between LeitungseinfOhrungsbohrungen Cable entry holes LeitungseinfOhrungsbohrungen Cable entry holes Gewindelange Anzahl der Thread engagement Gewindegange fmml Threads engaged > 20 > 13 > 20 >> 6 Gewindeart und -gate Nature and quality of thread M 20 x 1,5; mittel M 20 x 1,5; medium NPT 1/ Prufung von Atmungs- und Entwasserungseinrichtungen Porengro enbestimmung: Bericht GB 6.3-S020503a: Sinter 010 mm; Porengro e 162 µm; zul. Porengro e 190 µm Tests of breathing and draining devices Pore size measurement: Report GB 6.3-S020503a: sinter 010 mm; pore size 162 µm; permissible pore size 190 µm Seite 4 van 4 zum PrOfprotokoll - Page 4 of 4 of Test Report BVS PP EG I N1 Dieses Priifprotokoll darf nur vollstandig und unverandert vervielfaltigt werden This test and assessment report may only be reproduced in its entirety and without change

8 DEKR DEKRA EXAM GmbH Fachstelle ftir Sicherheit elektrischer Betriebsmittel.. BVS Dinnendahlstraf!.e Bochum Telefon Telefax Anderungsinformation - Revision Report Prufprotokoll - Test and Assessment Report BVS PP EG Die mit folgender Dokumentation festgelegte Anderung hat keinen Einfluss auf die in o.g. Prufprotokoll getroffenen Festlegungen. Die bisher in der Form M20x1,5 oder NPT 1/2" hergestellten t.eitungseinfuhrungen konnen jetzt alternativ auch in G 1/2" hergestellt werden. Die neue Gewindeart wurde erfolgrelch in BVS PS gepruft. The modification as defined in the following documentation does not influence the details of the aforementioned test and assessment report. The cable entry threads were manufactured in the type M20xl.5 ornpt 1/2" and can now alternatively be manufactured in the type G l/2". The new nature of thread was tested successfully in BVS PS Qokumentation -_Descriptive Documents Beschreibung llmd-a10/2009-p (1 Blatt) Description IIMD-Al0/2009-P (1 sheet), unterschrieben am -signed Beschreibung Prufmuster (2 Blatt) - Description test sample (2 sheet), unterschrieben am - signed Bochum, den BVS-Kr/Kw A DEKRA EXAM GmbH Fachstelle fii r Sicherheit elektrischer Betriebsmittel - BVS Der Sachverstandige - The Testing Officer Seite 1 von 1 zur Anderungsinformation zu - Page 1 of 1 of Revision Report to BVS PP EG Diese Anderungsinformation dart nur vollstandig und unverandert vervielf81tigt warden. This revision report may only be reproduced in its entirety and without change DEKRA EXAM GmbH Dinnendahlstraf!.e Bochum Telefon-Phone / Telefax-Fax / bvs-exam@dekra.com

9 Translation (1) 2. Supplement to the w Q L\ (2) (3) (4) (5) (6) EC-Type Examination Certificate Equipment and protective systems intended for use in potentially explosive atmospheres - Directive 94/9/EC Supplement accordant with Annex Ill number 6 No. of EC-Type Examination Certificate: Equipment: Manufacturer: Positioner type TZIDC-200/210/220 DMT 02 ATEX E 029 X (7) (8) (9) (10) ( 11) (12) G II 2G Ex d llc T 4/T5/T6 Gb DEKRA EXAM GmbH Bochum, dated 26 1h March 2013 Signed: Dr. Franz Eickhoff Signed: Gonther Schumann Certification body Special services unit Page of 3 to DMT 02 ATEX E 029 XI N2 This certificate may only be reproduced in its entirety and without change. DEKRA EXAM GmbH Dinnendahlstrasse Bochum Phone Fax zs-exam@dekra.com

10 (13) (14) (15) Appendix to 2. Supplement to the EC-Type Examination Certificate DMT 02 ATEX E 029 X 15.1 Subject and type Positioner type TZIDC-200/210/ Description The positioner is designed in type of protection flameproof enclosure. The positioner is designed for the transmission of an electrical signal into a pneumatic signal As pressure media neither flammable gases nor oxygen or oxygen enriched gases will be used. The positioner type Doc will be designated as type TZIDC-200/210/220. This supplement is issued to ensure the compliance of the equipment with the updated versions of the applicable standards Parameters Electrical data Voltage Current Pneumatic data Supply pressure Thermal data Temperature class Ambrient temperature range (16) Test and assessment report (17) maximum. If the positioner is used at an ambient temperature above 60 C or below -20 C, cable entries and cables approved for a service temperature corresponding to the maximum ambient temperature increased by 10 K respectively corresponding to the minimum ambient temperature shall be used. The dimensions of the flameproof joints are in parts other than the relevant minimum or maximum values of EN :2007. For information on the dimensions of the flameproof joints contact the manufacturer. Fasteners with a minimum property class of 10.12, A2-70 or A2-80 must be used for the closing of the flameproof enclosure. Page 2 of 3 to OMT 02 ATEX E 029 x I N2 This certificate may cnly be reproduced in its entirety and without change. OEKRA EXAM GmbH Olnnendahlstrasse Bochum Phone Fax zs-exam@dekra.com

11 We confirm th e correctness f e ranslation from th In the ca se of arbitration onl t erman wordi n g sh ea r man original e valid and binding. DEKRA EXAM G 09 Bochum 2!;, H M ay 2013 S-Ew/Ru/M A /J,' ti p_,1 Certification body --- fl ::: DEKRA EXAM GmbH Page 3 of 3 I A This cert fi o D in nendah l st ras te 4 :6' ly be e i : : T E X E 029 x I N2 d 1 s!ni without change 9 ochum Phone Fax zs-exam@d e k ra.::om

12 Translation (1) 3rd Supplement to the EC-Type Examination Certificate (2) Equipment and protective systems intended for use in potentially explosive atmospheres - Directive 94/9/EC Supplement accordant with Annex Ill number 6 (3) No. of EC-Type Examination Certificate: DMT 02 ATEX E 029 X (4) Equipment: Positioner type TZIDC-2** (5) Manufacturer: (6) Address: (7) (8) (9) (10) (11) (12) DEKRA EXAM GmbH Bochum, dated Signed: Simanski Certification body Signed: Dr. Wittler Special services unit ( DAkk lit. o-;. c rr Page 1of3 of DMT 02 ATEX E 029 XI N3 This certificate may only be reproduced in its entirety and without any change. DEKRA EXAM GmbH, Oinnendahlstrasse 9, Bochum, Germany, telephone , Fax , zs-exam@dekra.com

13 (13) Appendix to (14) (15) 3rd Supplement to the EC-Type Examination Certificate DMT 02 ATEX E 029 X 15.1 Subject and type Positioner type TZIDC-200 I 210 I 220 Volta e Current Thermal data Tern erature class/. T4' T51 T6 (16) Test and Assessment Report (17) Special conditions for safe use, 1/ I I I, ' ' 17.1 The position er is designed tor use at an ambient temperature range of -40 C up to 85 C at maximum. I If the positioner is used at an ambient temperature above 60 C or below -20 C, cable glands and cables approved for a service temperature corresponding to the maximum ambient temperature increased by 1 O Kor corresponding to the minimum ambient temperature shall be used. The dimensions of the flameproof joints are in parts other than the relevant minimum or maximum values of EN :2014. For information on the dimensions of the flameproof joints contact the manufacturer. Fasteners with a minimum property class of 10.12, A2-70 or A2-80 must be used for the closing of the flameproof enclosure. ( DAkkS,.. J I C.i,_ Page 2 of 3 of DMT 02 ATEX E 029 x I N3 This certificate may only be reproduced in its entirety and without any change. DEKRA EXAM GmbH. Dinnendahlstrasse 9, Bochum, Germany, telephone , Fax , zs-exam@dekra.com

14 > I We confirm the correctness of the translation from the German original. In the case of arbitration only the German wording shall be valid and binding. DEKRA EXAM GmbH Bochum, BVS-Kir/Nu A ert1 1cation bo y ( DAI<..,...,.,,,_ ;;. '0.. Page 3 of 3 of DMT 02 ATEX E 029 XI N3 This certificate may only be reproduced in its entirety and without any change. DEKRA EXAM GmbH, Dinnendahlstrasse 9, Bochum, Germany, telephone , Fax , zs-exam@dekra.com