OXY/FUEL WELDING. LX Series 1-Gauge Regulators Gauge shows bottle contents. Knob shows output pressure. Oxygen has 300 bar service, acetylene 20 bar.

Transcription

1 Original, multi-purpose Sifbronze No1 low-temperature rod for brazing of steels, cast iron, copper and its alloys. Use with Sifbronze Flux. See our Sif section for other pack sizes. Our Sifbronze No1 pre-coated with Sifbronze Flux, allowing faster continuous brazing. Ideal for general mild steel work and dissimilar applications. See our Sif section for other pack sizes. RR Sifredicote No 1 1.6mm 2.5kg RR Sifredicote No 1 2.4mm 2.5kg RR Sifredicote No 1 3.2mm 2.5kg Our low-carbon gas welding rod for mild steel and wrought iron applications. Free-flowing and ideal for panels, plates and fittings. Copper-coated for longer shelf life. See our Sif section for pack sizes. RO Sifbronze No 1 1.6mm 2.5kg RO Sifbronze No 1 2.4mm 2.5kg RO Sifbronze No 1 3.2mm 2.5kg Fluxed Silicon Bronze Brazing Rods Our Sifbronze No1 impregnated with Sifbronze Flux, allowing faster brazing of clean mild steel. See our Sif section for other pack sizes. Plain Silicon Bronze Brazing Rods RS Sifautobronze 2.4mm 2.5kg RS Sifautobronze 3.2mm 2.5kg Coated Silicon Bronze Brazing Rods For our full range of Sif brazing rods, see page 119 Steel Gas Welding Rods RO Sifsteel No mm 2.5kg RO Sifsteel No mm 2.5kg RO Sifsteel No mm 2.5kg LX Series 1-Gauge Regulators Gauge shows bottle contents. Knob shows output pressure. Oxygen has 300 bar service, acetylene 20 bar. AE2001LX Oxygen - S/S 1/G Reg AE2002LX Acetylene - S/S 1/G Reg LX Series 2-Gauge Regs Gauges show output pressure & bottle contents. Oxygen has 300 bar service, acetylene has 20 bar. AE3004LX Oxygen - S/S 2/G Reg AE3002LX Acetylene - S/S 2/G Reg LX Series Multi Stage Regs More accurate than single-stage. Displays pressure and contents. Oxygen 300 bar, acetylene 20 bar. AE7001LX Oxygen - M/S 2/G Reg AE7002LX Acetylene - M/S 2/G Reg LX Series Plugged Regs No gauges. Pressure shown on markings around the adjustment knob. Oxygen has 300 bar service, acetylene & propane have 20 bar. AE6001LXEXT Oxygen Ext stem side entry AE6002LX Acetylene AE6004LXEXT Propane Ext stem side entry LX Series Indicator Regulators Bottle contents status shown by indicator on top. Ideal on-site. Pressure is determined via markings around knob. Oxygen has 300 bar service, acetylene 20 bar. AE5001LX Oxygen Reg AE5002LX Acetylene Reg

2 OXY/FUEL CUTTING LX Series Made Side Entry Regulators For bottles which require the regulator to be connected from the side. An alternative to bottom-entry regulators with a 90 adaptor. The range includes single-stage one and two-gauge, and higher-accuracy multi-stage two-gauge models for oxygen, argon and dissolved acetylene gases. AE3004LXSEEXT 1-Stage 2-Gauge Oxy Reg Side Entry Long AE3002LXSEEXT 1-Stage 2-Gauge Acety Reg Side Entry Long AE7004LXSEEXT 2-Stage 2-Gauge Propane Reg Side Entry On-Site Oxy/Fuel Packages Complete packages consisting of plugged regulators, FBAs, a hose set (10m for cutting, 5m for weld+cut) and a torch (NM universal for cutting, or 3-part for cut +weld) with a selection of nozzles and accessories. Ideal for site use. Toolbox Onsite Cutting Kits PKGSITEACHD On-Site Oxy/Acet HD Cutting Set PKGSITEPCHD On-Site Oxy/Prop HD Cutting Set PKGSITEAWCHD On-Site Oxy/Acet HD Cut+Weld Set PKGSITEAWCLW On-Site Oxy/Acet LW Cut+Weld Set Our on-site cutting packages (as above) supplied in a durable metal toolbox for safe storage and transport. PKGCASEACHD10 Toolbox Site Oxy/Acet HD Cutting Set PKGCASEPCHD10 Toolbox Site Oxy/Prop HD Cutting Set LX Series Nitrogen Regulators PKGSHOPAWCHD Workshop Oxy/Acet HD Weld+Cut Set PKGSHOPAWCLW Workshop Oxy/Acet LW Weld+Cut Set Nitrogen is used in many applications, including refrigeration and chamber purging. Our nitrogen regulators are British Made and have a 300 bar service. All have two gauges, showing bottle contents and output pressure and have 3/8 BSP right-hand outlet fittings. AE3003LX 1-Stage 2-Gauge Nitrogen Regulator AE7003LX 2-Stage 2-Gauge Nitrogen Regulator AE7003LX10 2-Stage 2-Gauge Nitrogen Regulator - 10 Bar Workshop Cutting & Welding Kits Full workshop welding and cutting packages, with 1S 2G regulators, FBAs, a 5m hose set and HD 3-part torch with a selection of nozzles and accessories. Toolbox Cutting and Welding Kits Our workshop welding and cutting packages (as above) supplied in a durable metal toolbox for safe storage and transport. PKGCASEAWCHD Toolbox Oxy/Acet HD Weld+Cut Set PKGCASEAWCLW Toolbox Oxy/Acet LW Weld+Cut Set Leak Detection Spray Non-toxic milky spray in a 400ml can. Use on hoses, regulator nuts,valves, etc. EG3001 Leak-Tek Spray Order Before 4pm For NextDay Delivery (Mon-Fri)

3 Single-stage plugged propane regulator with 5/8 BSP bull-nose (inlet) and 3/8 BSP outlet. This model features left-hand threaded fittings. Works with standard propane bottles and the fitted propane hose to deliver a suitable propane supply to operate our range of heating torches. Meets relevant European Norms. Heating Propane Regulator BG5143 Propane Regulator BW800538PFT 5m Fitted Propane Way Adaptors Some sites choose to service several operators from a single pair of oxygen and fuel gas cylinders. In these circumstances, 3-way adaptors are often used to provide 2 or 3 regulator connections. Third output can be blanked off with the threaded plug. Available in LH & RH models. Connections are oriented at 12, 3 and 9 o clock. 90 Cylinder Valve Adaptors Some cylinder manufacturers now produce bottles which require the regulator to be connected to the bottle from the side. The 90 adaptors allow this to happen by keeping the regulator the right way up so that the pressure control knob and gauges are always in view. These adaptors are available in RH and LH versions. DA360LH 3-Way Adaptor - LH DA360RH 3-Way Adaptor - RH DA90RH Oxygen (RH) DA90LH Acetylene (LH) Argon To CO2 Adaptor Argon cylinders have a 5/8 BSP, RH thread female outlet connection and the regulator has a matching male bullnose, whereas CO2 cylinders have a 5/8 BSP, RH thread male outlet connection and the regulator has a matching female nut. This adaptor allows an argon regulator to connect to a CO2 cylinder. AEARGBN Argon To CO2 Adaptor CO2 To Argon Adaptor The CO2 To Argon Adaptor is used to connect a CO2 regulator to an argon cylinder outlet. The double-threaded brass adaptor has a CO2 bottle fitting at the top, which connects to the nut on the regulator inlet, and a 5/8 BSP righthand threaded fitting at the bottom, which screws in to an argon bottle. AECO2BN CO2 To Argon Adaptor Extensions Cylinder extensions provide an additional distance above the bottle outlet, terminating in a 5/8 BSP female fitting to receive the male bullnose of the regulator. Available in LH (fuel gas) & RH (oxy/ar) versions. DAEXTLH Cylinder Extension LH DAEXTRH Cylinder Extension RH Balloon Inflator Our economy handtight inflator is durable, easy to install and easy to use. Handtight cylinder connection requires no wrench for installation. Safe, easy operation by rubber tilt valve, which is simple to replace if it gets damaged due to excessive wear and tear. Horizontal one-piece model with all brass piston construction. AEBR125 Balloon Inflator

4 OXY/FUEL CUTTING Twin-Outlet Hose Valves These Twin-outlet valves let you connect two sets of hoses and torch equipment to a single gas inlet, in order to use a single set of bottles, regulators and flashback arrestors. With independent adjustment knobs, you can control the flow of gas from each outlet individually. 3/8 BSP fitting versions are available with Right Hand or Left Hand threads. DA YRH RH - (e.g Oxygen) DA YLH LH - (e.g Acetylene) Twin-Outlet Valves FBA Version These Twin-outlet valves let you connect two sets of hoses, flashback arrestors and torch equipment to a single gas inlet, in order to use a single set of bottles and regulators. With independent adjustment knobs, you can control the flow of gas from each outlet individually. 3/8 BSP fitting versions are available with Right Hand or Left Hand threads. DA YRHFBA RH - (e.g Oxygen) DA YLHFBA LH - (e.g Acetylene) Fine Adjustment Valves Used in series within a gas line, the fine adjustment valves are designed to allow the isolation and flow control of gas travelling through a hose. Available in Right-Hand (RH) and Left-Hand (LH) versions, the fine adjustment valves consist of a 3/8 BSP threaded female fitting and a 3/8 BSP threaded male nut, situated either side of a flow control valve and an adjustment knob. DA800RH RH - (e.g Oxygen) DA800LH LH - (e.g Acetylene) CO2 Regulator Nut CO2 cylinders have a male outlet and the CO2 regulator connects to it via a nut, which can become damaged over time from the wear and tear of changing bottles. This damage can cause leaks at the connection, so the regulator nuts are often replaced. Regulator bullnose stems can become damaged over time from general wear and tear incurred when changing bottles. This damage can cause leaks at the cylinder connection. Bullnose stems are available in several regulator thread sizes to suit different popular regulator manufacturers. DACO2NUT CO2 Regulator Nut 5.15 Regulator Bullnose Stems Regulator Nuts DASTEM12 Reg Stem 1/2x27TPI UK 7.50 DASTEM14 Reg Stem 1/4NPT UK 7.50 DASTEM26 Reg Stem 1/2x26TPI UK 7.50 DASTEMCO2 Reg Stem CO2 UK 7.15 DASTEMLX Reg Stem 5.60 Regulator nuts can become damaged over time from general wear and tear incurred when changing bottles. Our regulator nuts are 5/8 BSP, available in LH and RH versions. DANUTLHLX 5/8 BSP Reg Nut LH 8.65 DANUTRHLX 5/8 BSP Reg Nut RH 8.65 Replacement of regulator parts should only be undertaken by a trained professional. Air s Integra Arrestors Air s Integra cylinders have bespoke quick-connector fittings. These flashback arrestors allow connection of your regular equipment to the Integra fitting. AU AP Integra FBA - Oxy AU AP Integra FBA - Fuel Order Before 4pm For NextDay Delivery (Mon-Fri)

5 Barrel Type Flashback Arrestors Non-resettable FBAs for high flow oxy/fuel gas cutting & welding. Will withstand a series of minor flashbacks but will not react as a consequence of external heat. Can be connected in parallel for greater flow. AU Oxygen AU Fuel Gas Resettable Flashback Arrestors Provide the highest possible level of long-term protection. Clearly indicate the occurrence of a flashback and can be manually reset afterwards via their collar. Will withstand a series of flashbacks but will not react as a consequence of external heat. AU2001 Oxygen AU2002 Fuel Gas Oxy/Fuel Gas Economiser When you need to repeatedly start and stop welding or cutting, lighting and extinguishing the flame can be performed quickly and more easily by using a gas economiser. AE2000 Oxy/Fuel Economiser Plain Ni Bronze Brazing Rods Our 9% Nickel Sifbronze No2, for use on copper alloys, alloy steel and stainless steel, with excellent wear properties and high strength. Ideal for brazing tubes, cutting tips and use as a general maintenance alloy. When brazing stainless, use with our Sif Tool Tip / Braze Stainless Flux. RO Sifbronze No 2 1.6mm 2.5kg RO Sifbronze No 2 2.4mm 2.5kg RO Sifbronze No 2 3.2mm 2.5kg FO Tool Tip/Braze Stainless Flux 500g Jar A full range of gas welding consumables is available in the SIF Range detailed in full at the rear of this catalogue. Cup Type Sparklighter A single flint bar. Single strike action. Made from quality spring steel. Sold complete with fitted flint. Replacement flints are available in two types, in packs of 10pcs. DZ Cup Lighter 2.60 DZ105002B Cup Lighter Flints pk Tri-Flint Sparklighter Popular design of quality spring steel sparklighter, features a triple-flint strike action. Flints included, Spare flints sold as pack of 10 triangles. DZ Tri-Flint Lighter 3.35 DZ Spare Flints (10) 7.95 DZ Pistol - Nickel 4.70 DZ Spare Flints (10) 1.10 Red Pistol Sparklighter Nickel Pistol Sparklighter Makes use of a single flint and a trigger strike action. Popular design. Fitted with flint. Spare flints in pk 10. Similar to the nickel pistol sparklighter, but in a more economical red painted style. DZ Pistol - Red 4.05 DZ Spare Flints (10) 1.10 Oxy/Fuel equipment needs annual inspection by a certified inspector. Weldability Sif offer courses to BCGA practises. Contact your Weldability Sif trading partner today to discuss your training requirements. 06

6 OXY/FUEL CUTTING Fitted Hose Lengths - ISO 3821 Fitted oxygen, acetylene and propane hose. High-compression crimp fittings and non-return flame-traps. Available in a range of lengths and bore sizes with 3/8" or 1/4" BSP fittings B=oxy, R=acet,P=propane. bore fit len BW600514B/RFT 6mm x 1/4 x 5m B/R BW600514PFT 6mm x 1/4 x 5m P BW600538B/RFT 6mm x 3/8 x 5m B/R BW600538PFT 6mm x 3/8 x 5m P BW B/RFT 6mm x 1/4 x 10m B/R BW PFT 6mm x 1/4 x 10m P BW B/RFT 6mm x 3/8 x 10m B/R BW PFT 6mm x 3/8 x 10m P BW B/RFT 6mm x 3/8 x 20m B/R BW800538B/RFT 8mm x 3/8 x 5m B/R BW800538PFT 8mm x 3/8 x 5m P BW B/RFT 8mm x 3/8 x 10m B/R BW PFT 8mm x 3/8 x 10m P BW B/RFT 8mm x 3/8 x 20m B BW PFT 8mm x 3/8 x 20m P BW B/RFT 8mm x 3/8 x 30m P BW PFT 8mm x 3/8 x 30m R BW B/RFT 10mm x 3/8 x 5m B/R BW PFT 10mm x 3/8 x 5m P BW B/RFT 10mm x 3/8 x 10m B/R BW PFT 10mm x 3/8 x 10m P BW B/RFT 10mm x 3/8 x 20m B/R BW PFT 10mm x 3/8 x 20m P BW B/RFT 10mm x 3/8 x 30m B/R BW PFT 10mm x 3/8 x 30m P Single-Line Bulk Unfitted Hose - ISO 3821 EPDM hose to ISO 3821 : 2010, on 50m coils. Price per mtr. B=oxy, R=acet, PRP=propane. BW600B/R 6mm Hose Unfitted (Per Mtr) B or R 1.50 BW600PRP 6mm Hose Unfitted (Per Mtr) PRP 2.20 BW800B/R 8mm Hose Unfitted (Per Mtr) B or R 1.45 BW800PRP 8mm Hose Unfitted (Per Mtr) PRP 2.75 BW1000B/R 10mm Hose Unfitted (Per Mtr) B or R 1.60 BW1000PRP 10mm Hose Unfitted (Per Mtr) PRP 2.50 Twin Bulk Unfitted Hose - ISO 3821 Siamese oxy/fuel hoses (acet or propane). Price per mtr. BW600RBT 6mm TwinFlex R&B (Per Mtr) 2.60 BW800RBT 8mm TwinFlex R&B (Per Mtr) 3.00 BW800PBT 8mm TwinFlex P&B (Per Mtr) BW1000RBT 10mm TwinFlex R&B (Per Mtr) 3.20 BW1000PBT 10mm TwinFlex P&B (Per Mtr) 4.15 Fitted Hose Sets - ISO 3821 Set of 2 high quality oxy/fuel hose assemblies conforming to ISO 3821 : 2010 and manufactured from EPDM compound for high abrasion and weather resistance. With high-compression fittings and non-return flame-traps. Set of 2. BZ60514SETFT 6mm 5m 1/4 Oxy/Acet Set BZ60538SETFT 6mm 5m 3/8 Oxy/Acet Set BZ61014SETFT 6mm 10m 1/4 Oxy/Acet Set BZ61038SETFT 6mm 10m 3/8 Oxy/Acet Set BZ62038SETFT 6mm 20m 3/8 Oxy/Acet Set BZ80538SETFT 8mm 5m 3/8 Oxy/Acet Set BZ80538SETPFT 8mm 5m 3/8 Oxy/Prop Set BZ81038SETFT 8mm 10m 3/8 Oxy/Acet Set BZ81038SETPFT 8mm 10m 3/8 Oxy/Prop Set BZ100538SETFT 10mm 5m 3/8 Oxy/Acet Set BZ101038SETFT 10mm 10m 3/8 Oxy/Acet Set BZ101038SETPFT 10mm 10m 3/8 Oxy/Prop Set BZ102038SETFT 10mm 20m 3/8 Oxy/Acet Set BZ102038SETPFT 10mm 20m 3/8 Oxy/Prop Set Fitted Siamese Hose - EN559 / ISO 3821 Twin hose set assemblies joined for greater manoeuvrability. Fitted with flame traps. BZ81038SETFTSY 8mm Twin Set 10m 3/ BZ81038SETPFTSY 8mm Twin Set 10m 3/ BZ82038SETFTSY 8mm Twin Set 20m 3/ BZ82038SETPFTSY 8mm Twin Set 20m 3/ BZ101038SETFTSY 10mm Twin Set 10m 3/ BZ101038SETPFTSY 10mm Twin Set 10m 3/ BZ102038SETFTSY 10mm Twin Set 20m 3/ BZ102038SETPFTSY 10mm Twin Set 20m 3/ Double Hose Clamp Durable metal clamp, tightened via screw, to secure 2 lengths of a separate hose set. DA Double Hose Clamp 2.90 Inspect hoses regularly for cuts, abrasions, perishing, flashback incidents and replace as necessary. 07 Order Before 4pm For NextDay Delivery (Mon-Fri)

7 Hose Nuts Available to suit Oxygen, Argon, etc.. (RH) or Acetylene, Propane, etc.. (LH). Range includes 3/8 BSP (HD) & 1/4 BSP (LW) thread sizes. Conforms to EN1256. DA10014LH 1/4 BSP LH 2.15 DA10014RH 1/4 BSP RH 2.15 DA10038LH 3/8 BSP LH 2.30 DA10038RH 3/8 BSP RH 2.30 Hose Splicers Use with suitable hose clips to join 2 lengths of hose together without using threaded nuts and couplers. Splicers are available to suit a range of hose sizes. DA /4 BSP Hose Splicer 3.10 DA /8 BSP Hose Splicer 3.10 DA /16 BSP Hose Splicer 3.10 DA /16 BSP Hose Splicer 3.10 Hose Clips Also called O Clips, they are used to crimp over the ends of hoses to secure hose tails and create a gas-tight seal. A wide range of hose sizes is catered for. Priced each, packed in 10 s. Use with Hose Clip Pliers (page 70). (Each) DA /4 (5-7mm) 0.73 DA /16 (7-9mm) 0.78 DA /8 (8-11mm) 0.83 DA /16 (9-11mm) 0.81 DA /2 5mm Hose (11-13mm) 0.89 DA /16 6mm Hose (13-15mm) 0.89 DA /8 8mm Hose (15-18mm) 0.81 DA /4 10mm Hose (17-20mm) 0.89 DA /8 10mm Hose (20-23mm) 0.68 DA (23-27mm) 0.82 Flame Trap Check Valves A vital item of gas safety equipment. This product is used at the torch end of a hose to help prevent dangerous backfeeding of gases. A preferred design to traditional Hose Check Valves, the Flame Trap Valve is fastened inside the hose using hose clips. DA LHFT Flame-Trap FT 1/4-1/4 LH 9.50 DA RHFT Flame-Trap FT 1/4-1/4 RH 9.50 DA LHFT Flame-Trap FT 3/4-1/4 LH 9.50 DA RHFT Flame-Trap FT 3/4-1/4 RH 9.50 DA LHFT Flame-Trap FT 3/4-3/8 LH 9.50 DA RHFT Flame-Trap FT 3/4-3/8 RH 9.50 DA LHFT Flame-Trap FT 3/4-5/16 LH 9.50 DA RHFT Flame-Trap FT 3/4-5/16 RH 9.50 Hose Couplers A threaded connector used with hose nuts and tails to join 2 lengths of hose together. Available to suit a number of different thread combinations. Lefthand (LH) versions suit fuel gases & right-hand (RH) suit oxy, argon, etc.. Hose Tails Inserted into hose, to attach hose nuts. Available for a variety of hose bore sizes. Use with hose nuts and suitable hose clips to secure in place and seal. Conform to EN1256. DA LH 1/4-1/4 BSP LH 5.50 DA RH 1/4-1/4 BSP RH 5.50 DA LH 3/8-1/4 BSP LH 4.60 DA RH 3/8-1/4 BSP RH 4.60 DA LH 3/8-3/8 BSP LH 4.60 DA RH 3/8-3/8 BSP RH 4.60 DA /4 Tail x 1/4 BSP Nut 2.25 DA /4 Tail x 3/8 BSP Nut 2.25 DA /16 Tail x 3/8 BSP Nut 2.30 DA /16 Tail x 3/8 BSP Nut 2.30 DA /8 Tail x 3/8 BSP Nut 2.30 On-Torch Flashback Arrestors Ideally suited for configurations with long hose sets. Helps prevent hose fires and bursting which can result from serious flashback events. AU On-Torch FBA Oxy AU On-Torch FBA Fuel

8 OXY/FUEL CUTTING Straight Hose Adaptors Straight adaptors are used to convert the thread size of 1/4 BSP hose fittings in order to enable them to be connected to 3/8 BSP HD shank fittings. The adaptors are available in Left Hand (LH) and Right Hand (RH) versions, for fuel gases and inert gases respectively. DA SLH LH Straight Adaptor 2.90 DA SRH RH Straight Adaptor 2.90 Bent Hose Adaptors Bent adaptors are used to convert the thread size of 3/8 BSP hose fittings in order to enable them to be connected to 1/4 BSP LW shank fittings. The adaptors are available in Left Hand (LH) and Right Hand (RH) versions, for fuel gases and inert gases respectively. DA BLH LH Bent Adaptor 3.05 DA BRH RH Bent Adaptor 3.05 Shank & Mixer - LW & HD A shank carries oxygen and fuel gas and controls gas flow to the nozzle. A Mixer combines these 1 gases and holds the welding nozzle. Both are available in 2 types; the 2 more portable 'Lightweight', and 'Heavy Duty'. BB5001 HD Shank BB5003 HD Mixer BB6001 LW Shank BB6003 LW Mixer NM Universal Cutting Torches A popular design of oxy/ fuel gas cutting torch which is used with NM type nozzles. It features 3/8 BSP inlets, pressure control knobs and cutting oxygen lever. 18,27,36,48 & 60 lengths with 90º, 75º or 180º heads. BU100B NM Torch 18/90 (457mm) BU100B75 NM Torch 18/ BU100B180 NM Torch 18/ BU200B NM Torch 27/90 (685mm) BU200B75 NM Torch 27/ BU200B180 NM Torch 27/ BU300B NM Torch 36/90 (914mm) BU300B75 NM Torch 36/ BU300B180 NM Torch 36/ BU400B NM Torch 48/90 (1219mm) BU400B75 NM Torch 48/ BU400B180 NM Torch 48/ BU600B NM Torch 60/90 (1524mm) Cutting Attachments - LW & HD The Cutting Attachment fits to an oxy/fuel shank and is available in Heavy Duty and Lightweight versions. The HD model is used with ANM, PNM, ASNM and AGNM nozzles and the LW with AFN and ASFN. Both have an oxy control knob & cutting oxy lever. BB5002 HD Cutting Attachment BB6002 LW Cutting Attachment Model O Lead Burning Kit For very fine welding and brazing applications, including the fusion welding of thin gauge sheet metal up to 1.5mm (1/16 ) and delicate lead welding. The torch is very easy to handle and generates a small, focused flame ideal for precise, heat-sensitive situations, where it is important that the heat-affected zone is kept to a minimum. CCMOKIT Model ʻOʼ Kit (Torch & Tips) CCMONECK Model ʻOʼ Neck CCMO01 #1 Model ʻOʼ Tip (2-3mm) 7.05 CCMO02 #2 Model ʻOʼ Tip (4-5mm) 7.05 CCMO03 #3 Model ʻOʼ Tip (6-8mm) 7.05 CCMO04 #4 Model ʻOʼ Tip (10-20mm) 7.05 CCMO05 #5 Model ʻOʼ Tip (18-30mm) Order Before 4pm For NextDay Delivery (Mon-Fri)

9 NM Pivot Cutting Guide Easy circle cutting tool for use with NM style universal cutters. Fastens around the cutter s pipes. Pivots in a centre-punched guide hole. Versions to suit either British- Made or Imported design. Brass Cutter Headnuts Replacement headnuts for NM style universal cutters, HD and LW style cutting attachments. Used to hold the cutting nozzle in place. Sold individually. Pipe Cutter Machine A manual chain-driven pipe cutting machine that provides smooth, accurate cutting action by incorporating a low gear ratio and worm wheel drive. Cuts 5-50mm thick wall on pipe with mm (4-24 ) diameter. Bevelling head angle can be set quickly and accurately by scale on a rack and pinion. This complete package is supplied together with a 2.4m length of guide chain and a selection of ANM cutting nozzles. Solidly constructed using brass, chromed and stainless steel parts. TJ Pivot Guide (British) TJ111535IMP Pivot Guide (Imported) DZ0000 Headnut - NM 5.05 DZ001T3 Headnut - HD 4.05 DZ001LW Headnut - LW 4.05 BCG30INUT Headnut for cutting machines BCG30PCM Pipe Cutting Machine BCG30CHN Guide Chain 2.4m BCG30PCM25 Torch Holder Kit BCG30PCM49 Torch NM Roller & Circle Cutting Guides Made from machined brass and stainless steel, the roller guide keeps an optimum distance and makes the cutting of lines and shapes quick and easy. It can be used with NM style universal cutters and the HD type cutting attachment using ANM and PNM style cutting nozzles. Straight Line Cutting Machine Portable, automatic straight-line cutting machines, available in models to suit 115v and 230v input power supply. Supplied with a 1.8m length of distortion-proof steel track (extra 1.8m lengths also available) and a selection of cutting nozzles. Cuts straight lines and bevels on 5mm-50mm thick steel. Constant adjustable travel speed - in forward or reverse - to provide good machine-quality cuts. Robust, and compact manufacture with brass and stainless steel machined components. Simple design. TJ1602 Roller Cutting Guide TJ1082 Circle Cutting Guide BCG30I110 Straight Line Cutting M/C 110V BCG30I230 Straight Line Cutting M/C 230V BCG30ITRK Straight Line Cutting Track 1.8m BCGCIRCLE Optional Circle Guide (20cm - 2m r) BCG30II110 Double Torch Model M/C 110v 1, BCG30II230 Double 230v 1, BCG30IIKIT Double Torch Kit BCG30ITCH Replacement Torch BCG30HOSE Replacement Hose Set

10 OXY/FUEL CUTTING Welding & Cutting Boxed Sets Complete welding or welding and cutting kits with all torch-end parts and accessories. Supplied in a durable, plastic foaminsulated case, the kits include a shank, mixer and cutting attachment (if required) a range of nozzles, cleaner and bottle spanner. BBHDKIT HD Kit Welding & Cutting BBLWKIT LW Kit Welding & Cutting BBLWKITWLD LW Kit Welding Only Portable Gas Packages These units are complete equipment packages for oxy/fuel welding & cutting. They contain regulators, flashback arrestors, a shank, mixer, cutting attachment, hoses, a selection of nozzles, tools, goggles and a trolley. The package only excludes gas bottles, which are available from your local gas distributor or cylinder centre. BB1007 HD Style Portable Package BB2007 LW Style Portable Package Blanking Nozzles A selection of blanking nozzles for use in testing gas hand equipment for leaks. These nozzles have no outlet holes so they do not allow gases to pass through them, thus forcing them to exit via leaks in hoses etc. Available in ANM (HD) cutting nozzle style and LW and HD swaged welding nozzle style. CCANMB ANM Type Blanking Nozzle CCLWB LW Swaged Type Blanking Nozzle 7.05 CCSWB HD Swaged Type Blanking Nozzle 9.65 Welding Nozzles For Heavy Duty style mixer. A full High-Quality range. No. Thickness CCSW01 # 1-0.9mm 5.30 CCSW02 # 2-1.2mm 5.30 CCSW03 # 3-2.0mm 5.30 CCSW05 # 5-2.6mm 5.30 CCSW07 # 7-3.2mm 5.30 CCSW10 #10-4.0mm 5.30 CCSW13 #13-5.0mm 5.95 CCSW18 #18-6.5mm 6.05 CCSW25 #25-8.2mm 6.05 CCSW35 # mm 7.60 CCSW45 # mm 8.25 CCSW70 # mm 8.25 DH Type Neck and Nozzles DH fine welding tips and neck for use with the lightweight mixer. No. Thickness BB2005 DH Style Neck CCDH01 # 1-0.9mm CCDH02 # 2-1.2mm CCDH03 # 3-2.0mm CCDH05 # 5-2.6mm CCDH07 # 7-3.2mm CCDH10 #10-4.0mm CCDH13 #13-5.0mm CCDH18 #18-6.5mm Welding Nozzles Smaller swaged style nozzles for use with the LW mixer. No. Thickness CCLW01 # 1-0.9mm CCLW02 # 2-1.2mm CCLW03 # 3-2.0mm CCLW05 # 5-2.6mm CCLW07 # 7-3.2mm CCLW10 #10-4.0mm CCLW13 #13-5.0mm CCLW18 #18-6.5mm 4.60 CCLW25 #25-8.2mm Order Before 4pm For NextDay Delivery (Mon-Fri)

11 ANM / E ANM & ANME oxy/acetylene cutting nozzles for use with NM cutters or HD cutting attachments. (E) shows ANMEs, extended length nozzle types. No. Thickness CCANM01W 1/32 6mm CCANM02W 3/64 12mm CCANM03W 1/16 75mm CCANM04W 5/64 100mm CCANM05W 3/32 150mm CCANM06W 1/8 300mm CCANME01W 1/32 (E) 6mm CCANME02W 3/64 (E) 12mm CCANME03W 1/16 (E) 75mm CCANME04W 5/64 (E) 100mm CCANME05W 3/32 (E) 150mm CCANME06W 1/8 (E) 300mm ARCNM Rivet Cutting ARCNM nozzles are used with the NM type cutters and HD cutting attachments for cutting rivet heads. One size available. AFN Cutting Nozzles For use with a Lightweight cutting attachment. Available in 3 sizes to cut 3-6mm (1/8-1/4 ), 6-20mm (1/4-3/4 ) & 20-50mm (3/4-2 ). CCAFN01 #1-3-6mm CCAFN02 #2-6-20mm CCAFN03 # mm AGNM Gouging Nozzles CCARCNM ARCNM Nozzle AGNM nozzles gouge welds and plate using oxy/acetylene with the Heavy Duty cutting attachment or NM type cutter. 3 sizes are sold with a range of gouge widths. No. Gouge CCAGNM13 #13 6-8mm CCAGNM19 # mm CCAGNM25 # mm Sheet Cutting Nozzles The ASNM and ASFN sheet metal cutting nozzles are made to cut sheet mild steel to a 3mm maximum thickness. ASNM is designed to be used with the HD style cutting attachment. ASFN is used with the small, LW style cutting attachment. CCASNM ASNM Nozzle CCASFN ASFN Nozzle Apachi Type Nozzles Two-piece NM type cutting nozzles for use with Apachi ( MAP ) gas in an NM style cutting torch or HD cutting attachment. No. Thickness CC /32 3-6mm CC / mm CC / mm CC / mm CC / mm CC / mm NFF Cutting Nozzles NFF are 2-piece cutting nozzles that are used with propane or natural gas, in flat seat torches. No. Thickness CCNFF0 # mm CCNFF1 # mm CCNFF2 # mm CCNFF3 # mm CCNFF4 # mm CCNFF5 # mm CCNFF6 # mm PGNM Gouging Nozzles Like the AGNMs, PGNM nozzles are used with NM and HD cutters, but use oxy/propane to gouge. No. Gouge CCPGNM01 #1 3-6mm CCPGNM02 #2 5-9mm CCPGNM03 #3 6-12mm CCPGNM04 # mm

12 OXY/FUEL CUTTING PNM / E PNM & PNME oxygen/ propane cutting nozzles. (E) = PNME extended length. Victor Type Nozzles Single-piece 2-seat oxygen acetylene cutting nozzles for use with Victor style cutting torches. No. Thickness CCPNM01W 1/32 6mm CCPNM02W 3/64 12mm CCPNM03W 1/16 75mm CCPNM04W 5/64 100mm CCPNM05W 3/32 150mm CCPNM09W 7/64 200mm CCPNM06W 1/8 300mm CCPNME01W 1/32 (E) 6mm CCPNME02W 3/64 (E) 12mm CCPNME03W 1/16 (E) 75mm CCPNME04W 5/64 (E) 100mm CCPNME05W 3/32 (E) 150mm CCPNME06W 1/8 (E) 300mm No. Thickness CCV mm CCV mm CCV mm CCV mm CCV mm CCV mm CCV mm Combination Spanner Strong, black, drop-forged spanners with integrated cylinder key, 3/8 BSP or EU 19mm jaw for common hose nuts and 5/8 BSP jaw for common regulator nuts. DZ0001 Combi Spanner (UK Type) 2.65 DZ0001EN Combi Spanner (EU Type) 2.45 Nozzle Cleaner Sets Sets of reamers and a file for cleaning the holes in an oxy/fuel gas cutting or welding nozzle. Flip-out cases. DZ0003 Nozzle Cleaners Large 3.60 DZ0004 Nozzle Cleaners Small (Blue) 1.90 DZ0004WBTY Nozzle Cleaners Small (Red) 1.90 Toolbox Case A durable red-painted metal toolbox case measuring 66x27x25cm and weighing 3kgs. Can be sealed shut with metal latches and has a pull-out tool tray. Ideal for tool and accessory kits. VVC (Cr) M/C Nozzles VVC are used with machine cutters using propane to cut quickly and efficiently, with repeated accuracy. The popular Chromed type is available in 16 sizes. No. OP1000W Weldability Sif Toolbox Case No. Thickness CCVVC0 0 25mm CCVVC mm CCVVC mm CCVVC01/2 0 1 /2 38mm CCVVC1 1 50mm CCVVC11/2 1 1 /2 76mm CCVVC mm CCVVC21/2 2 1 /2 127mm CCVVC mm CCVVC31/2 3 1 /2 178mm CCVVC mm CCVVC4/0 4/0 6mm CCVVC mm CCVVC5/0 5/0 5mm CCVVC51/2 5 1 /2 228mm CCVVC7NH 7 300mm Cylinder Key Strong, drop-forged or nylon, black bottle keys. Fit valves on British type gas cylinders. DZ0002 Spindle Key (Drop Forged) 1.75 DZ0002NYL Spindle Key (Nylon) 1.85 Tank Wrench T-Bar style spindle key alternative. DZ0005 Tank Wrench Order Before 4pm For NextDay Delivery (Mon-Fri)

13 AHT Equipment AHT equipment is used in acetylene heating, in pipe bending, brazing, glass forming, etc. 3 nozzles are available, which offer increasing heating ability. All must be used with the AHT neck and HD mixer, which connect only to the HD shank. The NM nozzle adaptor or superheating mixer are not compatible. BFAHT025 # 25 Nozl 52k Btu/h BFAHT050 # 50 Nozl 91k Btu/h BFAHT100 #100 Nozl 139k Btu/h BFAHTNECK AHT Heating Neck BB5003 HD Style Mixer NM Heating Nozzle Designed to be used with the NM type cutter or HD cutting attachment for oxy/propane heating. The NM adaptor is threaded to connect to the heating nozzle. The nozzle itself has a holding nut at the heating end which can be removed to allow the consumable heating insert to be replaced when worn down during use. 102K-188K Btu/h BFPHNM NM Heating Nozzle BFNMI NM Heating Insert Propane Superheating Equipment H Type propane heating nozzles, available in a range of sizes with increasing heating ability. Can be used with HD shank (via neck & mixer) or NM cutter / HD attachment using NM nozzle adaptor. BF1H 1H Nozzle - 72k-163k Btu/h BF2H 2H Nozzle - 102k-188k Btu/h BF3H 3H Nozzle - 183k-361k Btu/h BF4H 4H Nozzle - 236k-406k Btu/h BF5H 5H Nozzle - 281k-618k Btu/h BFSN11 Superheating Neck 11 Long BFSN27 Superheating Neck 27 Long BB5004 Superheating HD MixerNM BFNMSHA Adaptor Heating Torch - Multi Head Used with propane gas in metal pre-heating, flame-cleaning, warming and the welding and brazing of copper pipe, with valve for fine adjustment of fuel gas flow. Connects via 3/8 BSP fitting at the base. 330mm length, with a burner diameter of 17mm. Weighs 650g. Includes a standard nozzle (fitted), float nozzle, pipe nozzle. Provides 9kBtu with standard nozzle, 26kBtu with float & pipe nozzle. Heating Torch - 45mm Used with propane gas in a diverse range of applications from preheating of metals to flame-cleaning and paint-removal. Incorporates a valve for fine adjustment of fuel gas flow and a lever to introduce a jet of heat as required. Connects via 3/8 BSP fitting. Provides 181kBtu heat. Measures 380mm in length, with a burner diameter of 45mm. Weighs only 650 grams. BG109-SF Heating Torch (Multi Head) Heating Torch - 60mm A more industrial propane heating torch, measuring 560mm in length with a 60mm diameter burner. Incorporates a valve and a lever to introduce a jet of heat as required. Provides 218kBtu heat. Connects to a propane gas supply via a 3/8 BSP inlet fitting. Suitable for white line removal and pitch-heating etc. Weighs 750g. Available with or without a piezo lighter, which ignites the torch without the need for a sparklighter. BG111 Heating Torch 60mm BG312 Above, With Piezo Lighter BG105-45L Heating Torch 45mm