SPECIFICATION SHEET. OMEGAFLEX, Ltd. TracPipe Flexible Gas Piping Specification Sheet Specification date. ProjectName

Transcription

1 OMEGAFLEX, Ltd. TracPipe Flexible Gas Piping Specification Sheet Specification date ProjectName Model Number(s) - FGP-SS4-50 FGP-SS4-40 FGP-SS4-32 FGP-SS4-28 FGP-SS4-22 FGP-SS4-15 FGP-SS4-12 Note: This Information Sheet should be read in conjunction with the TracPipe Design and Installation Specification available from If further information is required, please tech-help@omegaflex.net A. Standards & Certifications: All Semi-Rigid CSST gas piping system components must be: A.1 BS 7838 or BS EN Certified (CSST) Semi Rigid Flexible Gas Piping with Mechanical Attachment AutoFlare Fittings that conform to the latest BS standards for safe performance up to DN50. A.2 BS 7838 Specification for corrugated stainless steel semi-rigid pipe and associated fittings for low-pressure gas pipework of up to DN 50. A.3 BS 6891 Installation of low pressure gas pipework of up to 35 mm (R1.1/4) in domestic premises (2nd family gas). - Specification A.4 BS 5482 Code of practice for domestic butane and propane-gas burning installations Part 1: Installations at permanent dwellings, residential and commercial premises, with installation pipework sizes not exceeding DN25 for steel and DN28 for corrugated stainless steel or copper. A.5 IGEM/UP/2 Edition 2. The Institution of Gas Engineers and Managers communication 1729, Installation pipework on industrial and commercial Premises. B. Stainless Steel Tubing: B.1 Tubing shall be made from 300 series Stainless Steel Strip conforming to BS B.2 Tubing shall not be subjected to heat treating or annealing after the corrugation forming operation. B.3 Tubing shall be suitable for operation with Natural Gas, LP (Propane) and Butane. B.4 Tubing is rated for 500millibar (.5bar) (BS 7838 & BS EN 15266). 1

2 C. Polyethylene Jacket: C.1 The jacket shall be extruded from fire-retarded Polyethylene. C.2 Chlorinated plastics such as PVC are not permitted. C.3 Polyethylene is to be resistant to UV (ultra-violates). D. AutoFlare Mechanical Attachment Fittings: D.1 Fittings shall be made from yellow brass. D.2 Fittings shall be equipped with a stainless steel insert to pilot on the tubing ID (internal diameter) and provide a reliable flaring operation. D.3 AutoFlare fittings are available in straight male (BSP), straight female, copper compression, tee, reducer tee and coupling configurations. D.4 Fittings shall provide a metal-to-metal seal no (rubber, pastes or plastic based gaskets) E.1 Shut-off valves: (ECV or AECV) must be approved for fuel gas service and shall be rated for the same pressure as the gas piping system installed. F. Exposed Stainless Steel Protection: F.1 TAPE WRAP-AFTER GAS TIGHTNESS TEST Care must be taken after pressure test to ensure that no stainless steel pipe is visible. Any portions of exposed stainless steel behind the fitting nut shall be wrapped with self-bonding silicone tape TracPipe P/N FGP H-12, (25mm wide), or FGP H12PO, (50mm wide). This will reduce the possibility of later external corrosive attack. G. Unvented Voids: G.1 Pipe in Pipe System G.1 Ducts having a small cross sectional area and volume, (i.e. 0.01/m2 or less and 0.1/m³ or less, respectively), are considered to be adventitiously ventilated. G.2 BS EN 1775 and IGEM/UP/2 Edition 2, provided that the route is the shortest practicable, the integrity of the cover is maintained, and the end fittings (where the gas tight cover ends) are in a ventilated area. G.3 TracPipe s cover has been independently tested by BSI at pressures from 20mbar to 2bar to demonstrate that it performs satisfactorily as a sleeve, allowing free passage for gas flow between the stainless steel pipe and the outer cover to the end fittings, throughout this pressure range. G.4 The pipework is sleeved continuously through the unventilated duct or void, with the sleeve ventilated at one or both ends into a safe place. G.5 The unventilated duct or void is filled with a crushed inert infill to reduce to a minimum the volume of any gas which may accumulate. 2

3 G.6 In certain situations TracPipe can be used as a pipe in pipe installation.( refer to annex F in the latest revision of the TracPipe Design and Installation Guide H. Ventilation: H.1 Vertical and horizontal ducts containing TracPipe Corrugated Stainless Steel piping shall be ventilated to ensure that minor gas leakage does not cause the atmosphere within the duct to become unsafe. H.2 Vertical ducts may run freely through a number of stories or take the form of an enclosure at each story s level. Where ducts are continuous, ventilation can normally be achieved by the provision of openings sized in accordance with Table 1. Where the duct takes the form of an enclosure at each storey level, ventilation is normally required at high level only in each storey. Table 1. Free area of ventilation openings Cross sectional area Minimum free area of each of duct m2 opening m2 Not Exceeding and not exceeding and not exceeding 7.5 Exceeding 7.5 Cross sectional area of duct /150 of the cross sectional area of 3

4 I. Bend radius: TracPipe CSST runs should be installed with bend radiuses noted in Table 2. The bend radius should be measured at the inside of the bend. Table 2. Bend radii for TracPipe TracPipe Bend radius Size Recommended Minimum mm mm mm J. Fire stopping: J.1 Buildings containing flats and maisonettes, installation pipes shall be fire stopped as they pass from one floor to another unless in their own protected shaft which is ventilated top and bottom to outside atmosphere. J.2 When pipes pass through the protecting structure (i.e. compartment walls or floors) all openings should be kept as small, and as few in number as practicable, and should be suitably fire stopped in such a manner as to allow thermal movement of the pipe and ensure the fire resistance is not impaired. J.3 Any proprietary fire stopping should, when tested in accordance with the appropriate part of BS 476, achieve the relevant periods of fire resistance for the structure in respect of load bearing capacity, integrity and insulation. K. Pipe Supports and Fittings: K.1 Sizes to DN15: 2.0 metres for vertical runs and 1.5 metres for horizontal runs. K.2 Sizes DN22 and above: 2.5 metres for vertical runs and 2.0 metres for horizontal runs. 4

5 L. Burial: L.1 Externally- Pipework up to DN32 should be buried in accordance with BS 6891: 2005(1) for natural gas and BS : 2005(2) for Liquefied Petroleum Gas (LPG). For sizes DN40 and DN50, the requirements of IGEM/UP/2 Edition 2(3) should be followed for both natural gas and LPG. Joints must not be buried. L.2 BS 6891: 2005 (1) and BS (2) requires that TracPipe up to DN 32 should be buried externally at the following depths: Table 3. Burial Depths Pipework Location Minimum depth of cover (mm) Buried pipework in soil 375 Buried pipework below vehicular traffic 375 Buried below concrete with only pedestrian access 40 For TracPipe DN40 and DN50, IGEM/UP/2 Edition 2 (3) requires: Pipework Location Minimum depth of cover (mm) Carriageways 450 Path footways 375 Verges 375 Other fields and agricultural land 1100 Other private ground 375 L.3 Internally- TracPipe can be buried directly in concrete floors and should be installed in accordance with Table 3.There should be a minimum of 25mm depth of cover of screed above the TracPipe. Joints must not be buried. M. TracPipe Certification/Training M.1 Installers should be TracPipe certified. M.2 Omegaflex offers FREE on-site certification/training to any Installer, Mechanical Engineer or Architects. 5

6 N. Fittings: Part Number Description Size FGP-FST-12 AutoFlare DN12 x 3/8"R DN12 FGP-FST-15 AutoFlare DN15 x 1/2"R DN15 FGP-FST-22 AutoFlare DN22 x 3/4"R DN22 FGP-FST-28 AutoFlare DN28 x 1"R DN28 FGP-FST-32 AutoFlare DN32 x 1.1/4"R DN32 FGP-FST-40 AutoFlare DN40 x 1.1/2"R DN40 FGP-FST-50 AutoFlare DN50 x 2"R DN50 FGP-TM-12 Termination Mount DN12 DN12 FGP-TM-15 Termination Mount DN15 DN15 FGP-TM-22 Termination Mount DN22 DN22 FGP-TM-28 Termination Mount DN28 DN28 FGP-TF15-15 TracPipe Tee DN15xDN15xDN15 FGP-TF22-22 TracPipe Tee DN22xDN22xDN22 FGP-TF28-T28 TracPipe Tee DN28xDN28xDN28 FGP-TF22-T15 TracPipe Tee DN22xDN22xDN15 FGP-TF28-T15 TracPipe Tee DN28xDN28xDN15 FGP-RT-1001DN Tracpipe Tee DN28xDN22xDN15 FGP-RT-1002DN Tracpipe Tee DN28xDN22xDN22 FGP-RT-752DN TracPipe Tee DN22xDN15xDN15 FGP-CPLG-12 TracPipe Coupling DN12 DN12 FGP-CPLG-15 TracPipe Coupling DN15 DN15 FGP-CPLG-22 TracPipe Coupling DN22 DN22 FGP-CPLG-28 TracPipe Coupling DN28 DN28 FGP-CPLG-32 TracPipe Coupling DN32 DN32 FGP-CPLG-40 TracPipe Coupling DN40 DN40 FGP-CPLG-50 TracPipe Coupling DN50 DN50 FGP-15x15mm 15mm Comp for DN15 Trac FGP-22x15mm 15mm Comp for DN22 Trac FGP-22x22mm 22mm Comp for DN22 Trac FGP-28x22mm 22mm Comp for DN28 Trac FGP-28x28mm 28mm Comp for DN28 Trac FGP-32x22mm 22mm Comp for DN32 Trac FGP-32x35mm 35mm Comp for DN32 Trac FGP MTR BS746 1"Female for DN22 Trac FGP MTR BS746 1"Female for DN28 Trac FGP MTR BS746 1"Female for DN32 Trac FGP BSP 1/2" BSP Female for DN22 Trac FGP BSP 3/4" BSP Female for DN22 Trac FGP BSP 1/2" BSP Female for DN28 Trac FGP BSP 3/4" BSP Female for DN28 Trac FGP BSP 3/4" BSP Female for DN32 Trac 6

7 O. Final Torque: Tighten nut and body as though you were making up a flared tubing joint. Note the relation between hex flats at this point and continue to tighten for two additional hex flats (one-third turn) to obtain required torque and final leak- tight metal-to-metal seal. Maximum torques for sealing are: P. Description/Dimensions DN Torque: N.m Ft.lbs DN Inch 3/8 1/2 3/ /4 1 1/2 2 Jacket O.D. (max) mm Inside Dia. (nom) mm Wall Thk (mm)

8 8

9 TABLE G4 - Approximate pressure drop (mbar per metre) through TracPipe CSST at a given flow rate (cubic mettres per hour), for NATURAL GAS (relative density 0.60) m^3/hr DN10 DN15 DN20 DN25 DN32 DN40 DN50 Notes: ) Pressure drop information based on Standard Conditions of 21C and 1 bar. 2) Flow rates / pressure drop information above include losses for four 90-degree bends and two end fittings. For tubing runs with additional bends or fittings, increase pipe length by the values given in Table G7. 9

10 TABLE G5 - Approximate pressure drop (mbar per metre) through TracPipe CSST at a given flow rate (cubic mettres per hour), for PROPANE (relative density 1.52) m^3/hr DN10 DN15 DN20 DN25 DN32 DN40 DN50 Notes: ) Pressure drop information based on Standard Conditions of 21C and 1 bar. 2) Flow rates / pressure drop information above include losses for four 90-degree bends and two end fittings. For tubing runs with additional bends or fittings, increase pipe length by the values given in Table G7. 10

11 TABLE G6 - Approximate pressure drop (mbar per metre) through TracPipe CSST at a given flow rate (cubic mettres per hour), for BUTANE (relative density 2.07) m^3/hr DN10 DN15 DN20 DN25 DN32 DN40 DN50 Notes: ) Pressure drop information based on Standard Conditions of 21C and 1 bar. 2) Flow rates / pressure drop information above include losses for four 90-degree bends and two end fittings. For tubing runs with additional bends or fittings, increase pipe length by the values given in Table G7. 11