Trapping Protocols 2008 Emerald Ash Borer Survey
|
|
- Hillary Turner
- 5 years ago
- Views:
Transcription
1 Trapping Protocols 2008 Emerald Ash Borer Survey A. Trap Assembly (should be completed in the field) 1. Items needed: a. Traps (pre-glued) b. Cable ties - 7 inches long (2 per trap) c. Parchment or wax paper d. Utility knife 2. Two traps will come together with the glued faces touching. You should peel these apart. If you are only going to use one of the traps at a site, cover the exposed, sticky face of the other trap with the parchment (or wax) paper to protect it. Figure 1. Diagram of prism trap 3. The line (A) on the side containing the two slots should be scored with a utility knife (or similar item), taking care not to cut completely through the line. The two tabs (B) should be placed inside the slots (see picture below). Cable ties can be inserted into the holes marked (1) on Figure 1, and as shown below.
2 B. Low Trap Placement (on tree) 1. Items Needed: a. Assembled trap b. Cable ties - 7 inches long (4 per trap; 3 to attach the trap to the pole, 1 to attach the lure to the trap) c. Cable ties 4 feet long (2 per trap) d. Rebar pole ¼ inch diameter; 4 feet long with a 90-degree bend approximately in the middle, and a second slight (15-degree bend near the tip) 2. Attach the rebar pole to the tree by running two of the 4-foot cable ties around the diameter of the tree. One should be placed at the bend, and one at the bottom of the pole. 3. Seven-inch cable ties should be used to attach the traps to the pole the three positions marked (2) on Figure 1. The one at the bottom of the trap is not shown in the above photo, but the tie should be run around the pole, through the two holes, and then fastened. 4. The lure should be attached to the trap at hole (3) (Figure 1). Care should be taken to ensure the placement of the lure inside the trap, and not stuck to the glue on the outside. C. Low Trap Placement (off tree) 1. Items Needed:
3 a. Assembled trap b. Cable ties - 7 inches long (4 per trap; 3 to attach the trap to the pole, 1 to attach the lure to the trap) c. Cable ties 4 feet long (2 per trap) d. Rebar pole ¼ inch diameter; 8 feet long with a 90-degree bend approximately 1.5 feet down the pole so that the pole is L-shaped e. A rubber mallet or 5 pound sledge (may not be necessary) 2. Place the rebar pole in the ground, so that it stands upright. This may require the use of the mallet or sledge. 3. Place the trap over the top of the pole, so that the pole is inside the trap, and the top of the trap is flush with the top of the trap 3. Seven-inch cable ties should be used to attach the traps to the pole the three positions marked (2) on Figure The lure should be attached to the trap at hole (3) (Figure 1). Care should be taken to ensure the placement of the lure inside the trap, and not stuck to the glue on the outside. D. High Trap Placement (lower canopy). Pole Method 1. Items needed: a. Assembled trap b. Cable Ties 7 inches long (4 per trap; 3 to attach to spreader to the trap, and 1 to attach the lure to the trap) c. Spreader (may be different than in pictures below) d. Hanger
4 e. Pliers (or similar tool) f. Telescoping Pole (to 24 feet) with hanger attachment 2. The spreader can be attached to the holes in the trap labeled (4) on Figure 1 using the cable ties. The photos below illustrate this with the Umbrella Rig Spreader. Note: the design of the spreader may change. 3. The hanger should then be attached to the spreader at the loop in the top, and secured with the pliers. 4. The lure can be attached to the spreader on a loop located on the underside of the spreader. 5. Using the pole and attachment, the trap can be hoisted into the lower canopy, and the trap hanger placed over a (preferably large, stable) branch.
5 6. The trap can be taken down and serviced by slipping the attachment on the pole under the hanger, and lifting it off of the tree, and then down to the ground. E. High Trap Placement (lower canopy) Rope Method 1. Items needed: a. Assembled trap b. Cable Ties 7 inches long (4 per trap; 3 to attach to spreader to the trap, and 1 to attach the lure to the trap) c. Spreader (may be different than in pictures below) d. Hanger e. Pliers (or similar tool) f. Throw weight (14 or 16 oz) g. Throw line h. Rope (~ 100 ft per trap) i. Knife
6 2. Follow the methods described in Section C (High Trap Placement (Pole Method)) for spreader attachment. 3. Toss the throw line, tied to the weight over a branch in the lower canopy. Allow, or coax the weight to fall to the ground. 4. Untie the throw line from the weight, and tie one end of the rope to that end of the throw line. Pull the throw line and rope back over the branch. When the rope is over the branch and reachable, untie it from the throw line, and tie it to the top loop on the trap. Tie a second section of rope to the bottom loop on the spreader (where the lure is attached). This second section will now be the steering rope, while the original section will be the pulling rope.
7 5. Pull the trap up to the branch using the pulling rope, while keeping it from banging against the tree with the steering rope. The steering rope can later be used to help pull the trap down when servicing it. Wrap the excess rope from both sections around the tree (preferably apart from each other).
STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING
9390 South 300 West, Sandy, Utah 84070 801-562-0123 800-782-0500 ColonialFlag.com STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE
More informationSTATIONARY TRUCK INTERNAL HALYARD CAM CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL COMMERCIAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING
9390 South 300 West, Sandy, Utah 84070 801-562-0123 800-782-0500 ColonialFlag.com STATIONARY TRUCK INTERNAL HALYARD CAM CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL COMMERCIAL INSTALLATION READ ALL INSTRUCTIONS
More informationEmerald Ash Borer Trapping Procedures 2012
Emerald Ash Borer Trapping Procedures 2012 Texas Forest Service Goal: To survey ash habitats in selected counties in Texas to detect the presence of the emerald ash borer, EAB (Agrilus planipennis), following
More informationNAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS
NAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At regional competitions the ice is simulated by 8 ft x 4 ft ½-inch foam sheeting (Home Depot part #703990 [in store only],
More informationTrampoline Installation Instructions
Congratulations on purchasing an Oz Trampolines Product. Following are detailed setup instructions for your trampoline. Please ensure all boxes and parts are present before continuing. Setting Up Your
More informationAssembly Instructions. -Cantilever Boat Lifts
Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for
More informationChapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum
Chapter 2 Rigging Cutting Wire Rope The wire rope must be tightly seized on both sides of the point where the wire rope will be cut, as shown in Figure 2-1. Seize the wire rope with either seizing wire
More informationRigging it Right. Presented by Ron Barwick Service Manager for Half Hitch Hosted by: Bob Fowler
Rigging it Right Presented by Ron Barwick Service Manager for Half Hitch ron@halfhitch.com Hosted by: Bob Fowler bob.fowler@marinemax.com (850) 708-1317 marinemax.com www.halfhitch.com 1 The Uni-Knot Strong,
More informationESCONDIDO FIRE DEPT TRAINING MANUAL Section Truck Module Page 1 of 13 Ropes Equipment Aloft Revised
Truck Module Page 1 of 13 ROPES EQUIPMENT ALOFT The Escondido Fire Department has options for tying equipment to go aloft. One may use: Utility rope Utility rope after tying a figure eight Rope bag with
More informationHome Batting Cage. Assembly Instructions
PowerAlley Home Batting Cage Assembly Instructions IMPORTANT DO NOT RETURN THIS BATTING CAGE TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 IMPORTANT WARRANTY WARNING: DO NOT LEAVE
More informationTraps for Monitoring Apple Pests in Ohio
Traps for Monitoring Apple Pests in Ohio Pest Two target pests best suited for monitoring by traps in all Ohio orchards: Codling moth Apple maggot (especially in northern Ohio) Monitoring period bloom
More informationINSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
More informationRATLINER Assembly Instructions.
Model Shipways Inc. www.modelexpo-online.com RATLINER Assembly Instructions. Patent Pending 1. Remove center stands and braces from the main rigging frame. 2. The Stands and Braces should press release
More informationBALL STOP INSTALLTION GUIDE
BALL STOP INSTALLTION GUIDE GROUND SLEEVE INSTALLATION: 1. Locate the exact location of the ground sleeve. NOTE: Maximum recommended pole spacing is 20 feet on center. 2. Excavate the pole footing; refer
More informationPlace a rope coil here
1 2 3 4 The anchor buoys were made from Sculpey. You could however, carve them from wood but I wanted to continue my experimentation with this material. A buoy from this time period would have ranged from
More informationFiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual
Fiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual 27.75 23.75 25.50 20.75 Specifications: 8-13 GPM 100 strand fiber - Bubbler 75 strand fiber - Spillway Light Bar 45 ft. fiber tail
More informationTraps for Monitoring Apple Pests in Ohio
Pest Codling moth Pest San Jose scale Traps for Monitoring Apple Pests in Ohio One target pest best suited for monitoring by traps in all Ohio orchards: Monitoring period bloom (late April) until harvest
More informationXtender30. Home Batting Cage. Assembly Instructions
Xtender30 Home Batting Cage Assembly Instructions IMPORTANT DO NOT RETURN THIS BATTING CAGE TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 IMPORTANT WARRANTY WARNING: DO NOT LEAVE
More informationHillbilly Golf. Included. Game Building Instructions. 2-foot Fence Building Instructions. Bolo making Instructions
Hillbilly Golf Game Building Instructions Included 2-foot Fence Building Instructions Bolo making Instructions Minus Bar Building Instructions and Minus bar play rules Plus some Extras! Hillbilly Golf
More informationInfant Swing ( )
Infant Swing (04-0017) 1. Insert the yellow T-bar into the hole at the front of the swing. If you need to disengage the T-bar you can squeeze the 2 tabs together under the seat while pulling the T-bar
More informationAliphatic Resin Wood Glue. 18" Fabric Parachute Part #PNC50 Part # Part #11700 Part #J0016. Launch Lug
ADANCED * What you will need to build the Quest High-Q Hobby Knife * Straight Edge Pencil Aliphatic Resin Wood Sanding Sealer & Brush Spray Paint Parts and exploded view of the Quest High-Q Nose Cone 18"
More informationYour kit contains the following items. Additional Items You May Need. Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet
Your kit contains the following items Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet The SkyFox offers great glide performance in a rubber powered plane due to its built up wing.
More informationFNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions
FNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev: - Page
More informationTripod Setup Guide (M-TPx)
Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for
More informationa WOW Lab Prep Instructions
Pulleys and Mechanical Advantage A major step in the prep of this activity is choosing a good location. A key feature is an easily accessible top anchor. Some examples of good anchors are a solid tree
More informationMODEL / SINGLE and DUPLEX PULLEY SYSTEMS
MODEL 922181/922182 SINGLE and DUPLEX PULLEY SYSTEMS MODEL 922181 SINGLE PULLEY SYSTEM MODEL 922182 DUPLEX PULLEY SYSTEM 1 PARTS LIST FOR SINGLE/DUPLEX COLUMN PULLEYS Note: Check with your architect or
More information8-GUN CORVETTE ASSEMBLY INSTRUCTIONS
8-GUN CORVETTE ASSEMBLY INSTRUCTIONS THE HULL STEP 1 Fasten the Deck to the Hull. Find the hull. This is a large, pink, ship-shaped piece of insulating foam board. This will form the base of your model
More informationMODEL TRIPEX PULLEY SYSTEM
MODEL 922184 TRIPEX PULLEY SYSTEM 1 PARTS LIST FOR TRIPEX PULLEY SYSTEM Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your
More informationNEXT GENERATION FLEX FENCE
NEXT GENERATION FLEX FENCE Area To Be Fenced.. With Next Generation Flex Fence any post that is not in a straight line with another post must be braced. Layout your fence installation. Determine all end
More informationTRAINING BULLETIN ROPE 5 March 8, 2007 KNOTS AND HITCHES NOMENCLATURE
TRAINING BULLETIN ROPE March 8, 007 NOMENCLATURE Hitch A temporary method of securing an object, fastened so that it can be readily undone, i.e., Half Hitch. Bend The tying of the ends of two ropes to
More informationNAVIGATOR Product demonstration prop building instructions
NAVIGATOR Product demonstration prop building instructions Regional competitions may build product demonstration props out of materials other than PVC pipe. Your regional coordinator will inform you of
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationMaking Spars for the Schooner Jeanette
Making Spars for the Schooner Jeanette..... by Byron Rosenbaum Figure 1. Byron Rosenbaum s 1:16-scale radio-controlled model of the schooner Jeanette. All photographs by the builder. The spars required
More informationLMSCA. TECHNICAL INFORMATION SHEET No. 1 MANUFACTURE OF CARRIAGE LUGGAGE RACK NETTING.
LMSCA TECHNICAL INFORMATION SHEET No. 1 MANUFACTURE OF CARRIAGE LUGGAGE RACK NETTING. Preface: Luggage netting is one of those things that normally gets left until last when a carriage is restored and
More informationRANGER PROP BUILDING INSTRUCTIONS & PHOTOS
RANGER PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At the international competition, the science under the ice product demonstration will take place under an actual sheet of ice.
More informationMODEL CHEST PULLEY SYSTEM
MODEL 9180 CHEST PULLEY SYSTEM 1 PARTS LIST FOR CHEST PULLEY Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your facility.
More informationNATIONAL (NATO) STOCK NUMBER: NSN
THE SKED RESCUE SYSTEM NATIONAL (NATO) STOCK NUMBER: NSN 6530-01-260-1227 FLOTATION INSTRUCTIONS Please Post In Your Training Area SKED RAPID DEPLOYMENT FLOATATION SYSTEM Thank you for your purchase of
More informationPortable Soccer Goal Safety Program
Portable Soccer Goal Safety Program Overview This program addresses moveable/portable soccer goal safety, particularly full size or near full size goals. Soccer goals have caused dozens of deaths and hundreds
More informationAll Purpose Wooden Crate
All Purpose Wooden Crate I built a wooden crate to carry supplies in, such as, propane, ammo, fake explosives, tape and whatever else will fit in it. I would like to say right off the start that this does
More informationOFS LT1B Instruction Sheet Splice Organizer Comcode: D02AK0025 Installation
OFS LT1B 636-299-103-52 Instruction Sheet Splice Organizer Comcode: D02AK0025 Installation Preface This Instruction covers the installation of the LT1B Splice Organizer. Contents: Step 1 Identify Parts
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More informationFollow these easy steps to properly assemble your new Zim 420
Thank you for buying a Zim 420 and welcome to the Zim Sailing family. We are extremely proud of the quality of our boats and the race results are proven. Many of the top sailors are choosing Zim over other
More informationA Foundation Of Trust. Hanging By A Thread
Hanging By A Thread PROPS: Rope maker (See video at DoingWorks.com/movies.) 1 spool of cord for each team [I like to use 10 lb (4 kg test, 525 feet (160 meters) sisal cord] 1 spool of cord to use for demonstration
More informationBeginners/Basic Fly Tying Course
` Beginners/Basic Fly Tying Course Basic Tools Vise Scissors Hackle Pliers Bobbins Bodkin/Dubbing Pick Hair Stacker Dubbing Wax Head Cement Dispenser Whip Finish Tool Wing Burning Tools Tweezers Half Hitch
More informationInstallation of 2 Tier In Line Greeting Card Rack
Installation of 2 Tier In Line Greeting Card Rack Material Sent to Store: Greeting Card Fixtures: 4ft Inline Tier Kit (1 per every 4ft based on planogram) 3ft endcap Tier Kit (will not receive if planogram
More informationProp Racer System. User Guide V0210
Prop Racer System User Guide 59718 V0210 Introduction The CO 2 dragster racing activity is popular with older students, but has eluded elementary students due to its complexity. Pitsco s latest race system
More informationAdvancedTrak Rudder Kit AE4005. Assembly and Installation Instructions
AdvancedTrak Rudder Kit AE4005 Assembly and Installation Instructions Thank you for your purchase of the Advanced Elements AdvancedTrak Rudder Kit! A Kayak Rudder is a great way to enhance the tracking
More informationSetting Snares. Ohio Snaring Guide - 19
Setting Snares To set a snare, the looped end of the snare is suspended over a trail or path that the animal is expected to use. The animal enters the snare, sticking its head through the loop, and through
More informationVERSA BIKE RACK INSTRUCTIONS
VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than
More informationSplicing Instructions. Standard Double Braid Eye Splice Type 1 Double Braid Ropes
Splicing Instructions Standard Double Braid Eye Splice Type 1 Double Braid Ropes Introduction Double Braid Eye Splice This document describes the steps required to perform a Double Braid Eye Splice in
More informationRef Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
More informationCABLE REPAIR PROCEDURE 2100 Series, 2000 Series & Eventer
August 2005 CABLE REPAIR PROCEDURE 2100 Series, 2000 Series & Eventer 2000 SERIES 2100 SERIES EVENTER 7514 Alabonson Rd. Houston, Texas 77088 281-999-6900 281-999-6966 (fax) 51A Caldari Rd., #16 Concord,
More informationBuilding a Rocket (Advanced) Before you build a rocket try the bottle on the launcher to test if it holds pressure and fits correctly.
You Will Need 3X 2ltr Bottles 1X Paper lip 1X Glue/Double Sided Tape 1X ardboard 1X Bin Liner 1X Roll of Fishing Line or Thin s Sheets of Paper Side A of Fin 1X Hot Glue Gun 1X Pair of Scissors 1X Fine
More informationCONFER IN-GROUND CURVE STEP / IN-GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER IN-GROUND CURVE STEP / IN-GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-IG Note: 40 lbs. of sand required! SAND
More informationRocket Activity Rocket Wind Tunnel
Rocket Activity Rocket Wind Tunnel Objective Students predict the performance of their air rockets by measuring their streamlining properties. National Science Content Standards Unifying Concepts and Processes
More informationCONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-AG Note: 40 lbs. of sand required!
More informationThe Forest School Training Co. OCN accredited training
Useful Knots for Forest School The Overhand Knot 1. Cast an overhand loop. Take the working end and push it through the loop. The Figure of Eight Knot 1. Form a loop and pass the end under the standing
More informationBottle Rocket Launcher P4-2000
WWW.ARBORSCI.COM Bottle Rocket Launcher P4-2000 BACKGROUND: The Bottle Rocket Launcher allows for the exploration of launching rockets using commonly available materials such as plastic soda bottles and
More informationHEAVY DUTY H.S. DISCUS CAGE NET POLE NET POLE INSTALLATION
901020 - HEAVY DUTY H.S. DISCUS CAGE NET POLE NET POLE INSTALLATION www.gillathletics.com 800-637-3090 Install the pipe cap (PCAP00158002) at the top of the net pole. Install net pole pulley (73210042)
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationHoldUp Plus2. Safety Kit included: See additional instructions for installation. REAR WHEEL TRAY. BASE (1x) lock WASHER (1x) KEY (2x) SAFETY CLIP (1x)
HoldUp Plus2 InsTAll This product on 2" hitch version of the HoldUp Front WHEEL TRAY assembly (1x) REAR WHEEL TRAY assembly (1x) wrench (1x) BASE (1x) bolt (8X) Lock WASHER (8X) Washer (8x) KEY (2x) SAFETY
More informationStevenson Projects Building the Hull Top Deck and Bulkheads
Stevenson Projects Building the Hull 1. Print out both piece sheets. 2. Cut out one keel piece and glue it to a piece of balsa wood or dense cardboard. Cut out the second keel piece and glue it to the
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationSpeedbar parts. Settings
USER MANUAL Speedbar parts Settings 1) Layout setting (First step to the right or left) Default configuration is intended for the right-handed people, so the first pedal was placed to the right to ensure
More informationButler Parachute Systems, Inc
Butler Parachute Systems, Inc A division of Butler Parachute Systems Group, Inc. TT-600 GEN 1 & 2 TETHERED TANDEM BUNDLE DELIVERY SYSTEM ASSEMBLY MANUAL 1 JUN 2010 INTRODUCTION This manual contains all
More informationInstructions. Follow All Instructions Before Assembling Or Using This Product
Instructions Follow All Instructions Before Assembling Or Using This Product IMPORTANT DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 WARNING: Improper use
More informationExplain that this is how I did my tower, it does not necessarily represent the state of the art, nor even the right way to do any particular aspect
Explain that this is how I did my tower, it does not necessarily represent the state of the art, nor even the right way to do any particular aspect of the tower. I invite those more experience to make
More informationCaterpillar Tunnel. a s s e m b l y a n d i n s t r u c t i o n m a n u a l. Watch the video! Scan the code or visit: fflc.
Caterpillar Tunnel a s s e m b l y a n d i n s t r u c t i o n m a n u a l Watch the video! Scan the code or visit: fflc.us/tunnel/s Tools needed: Assembling the Bows Tape measure (Preferably 100') Sledge
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More informationPro Climb Rigging Bollard USER MANUAL. Pro Climb Rigging Bollard
Pro Climb Rigging Bollard USER MANUAL Pro Climb Rigging Bollard www.proclimb.co.nz Protection Rubber Wear Sleeve Picture 1 Rigging Loop Introduction The Pro Climb Rigging Bollard (PCRB) is a friction device
More informationInstallation Instructions Topo Ceiling System
Topo Ceiling Page 1 of 12 Before beginning installation of the TOPO Ceiling, check the enclosed bill of materials to ensure that all parts are present and undamaged. Read all installation instructions
More informationBelow are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
More informationUSG Ceiling Solutions. LOGIX Integrated Ceiling Systems INSTALLATION GUIDE
USG Ceiling Solutions LOGIX Integrated Ceiling Systems INSTALLATION GUIDE LOGIX Integrated Ceiling Systems INSTALLATION GUIDE Logix Brand Integrated Ceiling Systems integrated ceiling systems from USG
More informationCourse Code: 5114 Tied Up In Knots
Course Code: 5114 Tied Up In Knots Mt. Diablo-Silverado Council Leader Education & Discovery Conference January 30, 2016 Instructor: Bruce F. Lezer, Pack 262 1 Introductions Please share the following:
More informationDAS Dark Site Windscreens
DAS Dark Site Windscreens Instructions for Installation, Use and Stowing Revised April 15, 2018 This publication is intended to assist DAS members using the windscreens at the Edmund G. Kline Dark Site
More informationThe importance of splicing especially for braids made with UHMWPE fibre
The importance of splicing especially for braids made with UHMWPE fibre Nautilus has installed a high spec strength tester for testing ropes up to 14tonnes. There has been much knowledge gained as we can
More informationIce Axe-Boot belay Freedom of the Hills p. 350 Watch:
Carabiner-Ice Axe Belay Freedom of the Hills pp.358-359 Watch: http://bit.ly/carabinericeaxebelay Also called the stomper belay, the carabiner-ice axe belay provides better security than a boot-axe belay
More informationTo Purchase This Item, Visit BMI Gaming (800)
How to play the game How to play the game The object of the game is to reach the Game Goal before your opponent. HOW TO START: - A coin toss decides who starts the game. The winner of the coin toss also
More informationCONSTRUCTOPEDIA NXT Kit 9797
CONSTRUCTOPEDIA NXT Kit 9797 Beta Version 2.0 August 17, 2007 Center for Engineering Educational Outreach Tufts University Table of Contents Simple Shapes and Structures. Page 3 Ways To Attach NXT Motors...
More informationA N C H O R T A B S N O R T H W E S T ANCHOR TAB VF. Patented. User Instructions
A N C H O R T A B S N O R T H W E S T www.anchortabs.com ANCHOR TAB VF Patented User Instructions National standards, and state, provincial, and federal laws, require installer/user of this product to
More informationJourneyman Team Events
Journeyman Team Events Journeyman Team Rules Journeymen Teams Journeymen teams for the Florida Lineman Competition are comprised of three participants: 1. At least one of the climbers must be a Lineman
More informationGreat Science Adventures
Great Science Adventures What is a class one lever? Lesson 12 Tool Concepts: Class one levers consist of a rod, fulcrum, load arm, and effort arm. The fulcrum divides the lever into two sides. One side
More informationInstallation and Training Manual
AirForce1 Tower Kit Installation and Training Manual FuturEnergy Limited Ettington Park Business Centre Stratford upon Avon CV37 8BT +44 (0)1789 451070 Table of Contents Safety Notes... 3 Parts Supplied
More informationAssembly Guide ST200 FUNCTIONAL TRAINER
Assembly Guide ST200 FUNCTIONAL TRAINER Assembly Guide ST200 FUNCTIONAL TRAINER To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding,
More informationGround Release Shackle
Operator Manual Subhead Advantages: In the process of installing Slide Rail, the shackle connecting the top of posts, panels, and sheeting must be removed manually. This is normally done by climbing on
More informationLab # 3 -- Ropework. In this exercise the student will learn to work with rope by making a rope halter, splicing the rope, and tying common knots.
Description: Lab # 3 -- Ropework Name In this exercise the student will learn to work with rope by making a rope halter, splicing the rope, and tying common knots. Materials: 15' -- 1/2 polypropylene rope
More informationNautique Triton Clamping Board Rack V2
w w w.ro swe l l marine.co m Nautique Triton Clamping Board Rack V2 Installation & Usage Instructions Part # C917-180045 Information: info@roswellmarine.com If you have any questions please call : 1-21-68-11
More informationMANITOWOC MODEL TON CAPACITY
LIFTING CHARTS - Crawler Cranes ANITOWOC ODEL - 0 TON CAPACITY BOO RIGGING GUIDE ODEL AND # EL BOO Table of Contents General... Assist Crane Requirements... Accessing Parts... Installation and Removal
More information1. Select a level area 10 feet by 20 feet for assembly and placement of the enclosure. 2. Assemble the roof frame of the multi-purpose canopy kit according to the manufacturer s instructions. 3. Measure
More informationA Basic Guide to Europe Dinghy Rigging
The Basics: A Basic Guide to Europe Dinghy Rigging Use the smallest blocks available for the line size. Most of the blocks on your boat will be micro blocks. Examine all of your rigging and ensure that
More informationSPOOLER INSTRUCTIONS. STEP 12 If you are going to paint your posts, that should be done at this time.
STEP 4 Starting where you marked the end post location, move down your fence line 6 feet and make another mark. This mark is where your second upright post will be installed. Continuing down the fence
More informationChapter 16 Workbook Questions
1. List four defects that might be found during rope inspection that would require a rope to be retired. a. b. c. d. cuts, excessive fraying, abrasions puffs, pulled or herniated fibers changes in diameter
More informationSafety System Installation Guide for ARE Wind Poles
Safety System Installation Guide for ARE Wind Poles V. 1 May 2011 ** Climbing pegs and ladder should be installed before the pole is erected.** A. Install climbing pegs Install climbing pegs (bolt set)
More informationAlternate Sked Lashing Methods From Roco Rescue. Approved by Skedco.
Presented by: Roco Rescue Roco Rescue, Inc. 12-11-12 Alternate Sked Lashing Methods From Roco Rescue. Approved by Skedco. Warning: Proper training is required prior to use of this or any other rescue equipment
More informationBuilding 'TANGLER' The Fighter Kite That Helped Me Win The 2003 Fighter Kite Line-Touch World Cup Championship. Bruce Lambert
Building 'TANGLER' The Fighter Kite That Helped Me Win The 2003 Fighter Kite Line-Touch World Cup Championship Bruce Lambert kitefighter@yahoo.com The following method of building a fighter kite works
More informationDIY Shallow Water Anchor Assembly Instructions for Rods, T-grips, Stainless Tips, Stainless Couplers, and the 4-in-1 Paddle
DIY Shallow Water Anchor Assembly Instructions for Rods, T-grips, Stainless Tips, Stainless Couplers, and the 4-in-1 Paddle All Shallow Water Anchor Parts First, start by laying out and identifying all
More informationShade Sails - Installation Tips
Shade Sails - Installation Tips Shade Sails Installation Suggestions Design and Layout: Shade Sails can be mounted in a variety of ways. Sails can be mounted flat or with high and low points. A flat sail
More informationLaying out the Grid Laying out an accurate grid pattern in the sand is very important in order to get the columns and rows straight and true.
Laying out the Grid Laying out an accurate grid pattern in the sand is very important in order to get the columns and rows straight and true. As of this writing, the plot is 72 feet wide by 156 feet deep
More informationTHE AMERICAN BARN DOOR KITE
THE AMERICAN BARN DOOR KITE Oregon Kitemaker s Retreat January 2007 Rod Beamguard 4104 NW 112 th Way Vancouver, WA 98685-3578 (360) 574-8050 home (360) 750-9833 office kytfevr@wa-net.com PLANFORM BARN
More informationYou can use a variety of materials for this kite, such as Tyvek, ripstop nylon, Orcon, paper, or mylar or mylar-like plastic gift wrap films.
Woody's " Woodtick " Fighter Kite This kite is easy to make and easy to fly. It's performance will allow you to learn all fighter kite flying skills, plus put an ear to ear grin on your face. What more
More information