A T Cowen & Son Ltd. EN 1279

Transcription

1 The components and manufacturing process described in the following sections provide a detailed reference of the base Insulating Glass Unit tested to BS Part-2 & Part-3. Unique Product Reference No: A T COWEN & SON LTD. BS /2 3 KM ALUMINIUM SPACER BAR + P.I.B. + BOSTIK P5125 HOT MELT BUTYL GLASS: PILKINGTON / SAINT-GOBAIN / GUARDIAN Optifloat Clear and Tinted (4,6 & 10 mm thick) (Optional) Low E Surface Coating: Self Clean Solar Control Optional Glass Type (Optional) Obscure Glass (Optional) Laminated (6.4, 6.8, 8.8, 10.8 & 12.8mm thick) Thickness (mm): 4,6 & 10mm Number of Panes: 2 / 3. Glass cutting +2 mm -1 mm INNER SEALANT Equipment used for Application: Poly-Iso-Butylene (P.I.B.) LJF (LE JOINT FRANCAIS) BOSTIK LJF - Totalseal 3524 Bostik Lisec LBH-V Coating weight 1.2 to 3.0 gms per metre per side Coating weight 1.4 to 2.8 gms per metre per side Page 1 of 5 Issue Date 1 st Aug 2008

2 OUTER SEALANT: Hot Melt Butyl Insulating Glass Sealant BOSTIK HB FULLER Bostic P5125 H B Fuller HL 5147 Seal Properties Report Reference and Date: Equipment used for Application: Refer to Sealant Manufacturers Specification Hot Melt Gun / For.El Robot Gunning Line Seal Width Seal Width Air Pockets Air Pockets 7 mm (+2.5/- 2.0 mm) (9.5mm & 5.0mm) 7 mm (+2.0/-1.5 mm) (9.0mm & 5.5mm) No air pockets >2mm diam. At the corners No more than 3 air pockets >2mm diam. per meter of spacer bar. DESICCANT: Moisture Absorption Capacity: Molecular Sieve GRACE DAVISON EUROSIV GRACE DAVISON W558 EUROSIV - 3A : Std 1.3mm (If not provided a standard value of 20% will be used) No of Sides where Used: LONG: 2 sides SHORT: 0 sides Option; When Long side is at least 4 times longer than Short side. LONG: 1 sides SHORT: 0 sides Page 2 of 5 Issue Date 1 st Aug 2008

3 SPACER: Anodised Aluminium PROFILGLASS LPD Metric Spacer bar Width and Depth (mm): 5.5 mm to19.5 mm 6.4 mm depth Spacer bar cutting ±1 mm No dents allowed or splits in weld. CORNER PIECES AND CONNECTORS Method of Fixing: Nylon PROFILGLASS None Manual push in LEAD TAPE: DURALEAD REGALEAD MAGDEN LTD Duralead - Art-Deco Width and Thickness (mm): Applied to which Glass Face(s) Regalead Natural, Brass, Antique & Ebony Magden Preier & Antique Size range (3mm 12mm) Oval 1 & 2 (both sides) Page 3 of 5 Issue Date 1 st Aug 2008

4 COLOURED FILM Polyester DURALEAD REGALEAD CHAMELEON Duralead - Multi Film Colour(s) Used: Magdens Multifilm Chameleon Colour Film Range Full Range of Colours EDGE TAPE (if used): Polythene coated cloth tape THERMOSEAL LTD 38 & 45mm wide GEORGIAN BARS: Powder coated aluminium PROFIL GLASS Dimensions (mm): 18 x 8mm 25 x 8mm George IV & George V (Lightweight) [Various Colours] Fixing Accessories GAS FILLING: Gas Type: Argon Barometric Pressure 1015 m bar Ambient temp 16 degree C. Nominal Filling Concentration 85% + 10% - 5% Position and Dimension of Filling Holes: Filling Holes Closure Method: Type of Filling Equipment Used: Bottom Corner - 2mm / For.el [Flood] Gas Press. Mylar Film Inagas IGA 10 / For.El Gas Press / Willan Argonfill-4. Page 4 of 5 Issue Date 1 st Aug 2008

5 DIAGRAMS: NOTES: Diagram (1) Diagram (2) Diagram (3) Details of the Spacer Bar Cross Section Details of the Edge Seal Dimension Details of the Georgian Bars Please supply these on separate sheets GENERAL The purpose of the System Description is to fully define the base product covered by the test report. It must be detailed in every aspect such that there is no doubt about the products and components used in its manufacture UNIQUE PRODUCT REFERENCE NO This is a unique reference number associated with this product description document. It is used as the defining reference for the product and will be quoted in test reports and certificates where applicable. BS Kitemark applicants should leave this blank as the Kitemark Licence No. is used. MANUFACTURER This is the name of the company that manufactured the product not the supplier that you purchased the product from. TYPE REFERENCE This is the name and product identifier given by the manufacturer. ALLOWABLE DEFECTS These are separated into two limits: Absolute Limit This is the limit at which you reject units. All units outside this limit must be disposed of, for example, the seal depth may be described as 5mm minimum however, you may wish to allow a seal depth of between 5mm and 4mm for a maximum of 25mm per metre of unit perimeter. Any unit where there is more than 25mm of seal depth between 4 and 5mm must be rejected. You may also wish to allow 3 air cavities up to 3mm in diameter per metre of unit perimeter. Likewise, if 4 air cavities are present or the diameter of any air cavity is greater than 3mm then the unit is rejected. Action Limit This is the limit at which you take action to improve the relevant parameter, for example, you may wish to set an action limit of 10mm for the length of seal with a depth below 5mm. If, during inspection, this limit is observed then you will need to take action to reduce or eliminate the undersized seal depth. Page 5 of 5 Issue Date 1 st Aug 2008