Operating Instructions Single/Dual Bourdon Tube Pressure Switches Type BS/BT/BX
|
|
- Maximillian Watts
- 5 years ago
- Views:
Transcription
1 pproval data for Ex i swithes (BT and BX) pproval: II 1 G D Ex ia IIC T6 Ex ia D 20 T0 Operating Instrutions Single/Dual Bourdon Tube Pressure Swithes Type BS/BT/BX Certifiate no.: ISSeP08TEX016X Permissible ambient temperature: -40 C +75 C Eletrial data for intrinsially safe appliation: Ui = 28V Ci = 40 pf Ii = 50 m Li = 4 µh Standards applied: IEC , IEC , IEC , IEC and IEC pproval data for Ex d swithes (BX) pproval: II 2 G Ex d IIC T6 and Ex d IIC T6 Gb II 2 D Ex td 21 IP 65 T 80 C and Ex tb IIIC IP 65 T 80 C Certifiate no.: ISSeP08TEX024X Standards applied: IEC , IEC , IEC and IEC Operating life time Normal expeted servie life (expressed in the number of yles over the full adjustment range) is appr. 1 million for the swith. This may be extended to 2.5 million yles max. if only a part of the adjustment range is used (about 20%). 1 Intended ppliations Safety Instrutions... 2 Standards... 4 Warranty/Guaranty... 5 Installation/Commissioning Maintenane/Cleaning Tehnial Data... 8 Swith sensor life may also be effeted negatively by: Media not ompatible with the wetted materials. Too high swith yling speed or more than 20 yles per minute. System yling exeeding the top of the adjustable range. The proof must never be exeeded to avoid permanent sensor damage. Mathing the working range of the swith to the appliation is also a key for optimal swith performane. For greatest auray the set point should fall in the upper 70% of the adjustable range. For most favourable life the set point should be in the lower 0% of the adjustable range. Therefore, the most favourable ombination of auray and life fator lies between 0% and 70% of the adjustable range. Barksdale GmbH Dorn-ssenheimer Straße 27 D-6120 Reihelsheim Phone: +49 (605) Fax: +49 (605) and info@barksdale.de Internet: rt. no.: Index J, Speifiations are subjet to hanges without notie! 12 1
2 1 Intended ppliations The swithes are speifially applied for monitoring and ontrolling of operations using maximum and minimum s. miro swith triggers an eletrial signal when minimum or maximum are reahed. DNGER The swith may only be used in the speified fields of appliation (see type label). The temperature has to be within the speified ranges, the values and the eletrial rating must not exeed the values speified. Observe also the appliable national safety instrutions for assembly, ommissioning and operation of the swith. The swith is not designed to be used as the only safety relevant element in pressurized systems aording to DGR 97/2/EC. Without speial provisions/ations, swithes must not be used for pure hydrogen appliations. 2 Safety Instrutions The safety instrutions are intended to protet the user from dangerous situations and/or material damage. In the operating instrutions the seriousness of the potential risk is designated by the following signal words: DNGER Refers to imminent danger to men. Nonobservane may result in fatal injuries. WRNING Refers to important information essential to the user. Standards Disposal The equipment must be disposed of orretly in aordane with the loal regulations for eletri/eletroni equipment. The equipment must not be disposed of with the household garbage! The standards applied during development, manufature and onfiguration are listed in the CE onformity and manufaturer's delaration. 4 Warranty/Guaranty Warranty Our sope of delivery and servies is governed by the legal warranties and warranty periods. Terms of guaranty We guaranty for funtion and material of the single- / dual- swith under normal operating and maintenane onditions in aordane with the statutory provisions. Loss of guaranty The agreed guaranty period will expire in ase of: hanges or modifiations to the swith/housing/fitting inorret use, inorret installation or inorret handling or operation ontrary to the provisions of these operating instrutions. No liability is assumed for any damage resulting therefrom, or any onsequential damage. Refers to a reognizable danger. Nonobservane may result in fatal injuries, and destroy the equipment or plant parts. CUTION Refers to a danger. Nonobservane may result in light injuries and material damage to the equipment and/or to the plant. 2
3 5 Installation/Commissioning DNGER Only install or uninstall the swith when deenergized (eletrially and hydraulially/pneumatially). Pressure onnetion and eletrial onnetion must be arried out by trained or instruted personnel aording to state-of-the-art standards. The swith must only be installed in systems where the maximum P max is not exeeded (see type label). WRNING Contat Protetion The miro swithes used are normally suitable for both diret and alternating urrent operation. Indutive, apaitive and lamp loads may, however, onsiderably redue the life expetany of a miro swith and, under extreme irumstanes, even damage the ontats. Depending on the appliation spark suppression and urrent limiting is reommended (see sueeding figures). R1 C able R2 R R R Pressure peaks and shoks exeeding the maximum operating are inadmissible. The maximum operating is the upper final value of the adjustable range or, if speified, the indiated as maximum operating. Exeeding the max. operating affets the performane and the life span of the produt and may damage it. Install the swith as far as possible free from vibration, sine otherwise the swithing auray might be impaired. WRNING Fig. 1: Protetion in ase of apaitive loads R1: Protetion against starting urrent rushes R2,R: Protetion against high disharge urrents U = Fig. 2: Lamp load provided with resistane in parallel or series onnetion to swith of ondensators U Chek the swith regularly for funtioning. If the swith does not work properly, stop operation immediately! Diode R ll swithes are tested for proper funtioning before they leave the fatory. The fatory proof s are stated on the type label. Fig. : Protetion in ase of ontinuous urrent and indutive load by reovery diode Fig. 4: Protetion in ase of alternating urrent and indutive load by RC-link Set point adjustment Fatory-Provided: (temperature) swith point setting We onfirm for (temperature) swithes that have been fatory set the setting will be detailed on the label name plate. Warranty is not appliable for any hanges that may our due to transportation or installation. For ritial appliations we reommend the setting is heked and re-set if eessary after installation and wirding of the (temperature) swith. 4 5
4 In swithes, a displaement of the sensing element ours with a hange in. Following the displaement of the sensing element operates a miroswith. Upon delivery of the produt, the set points are likely to be found in the middle of the adjustable range. On request, fix set points may be adjusted by our fatory. In this event, the point will be indiated on the type plate or any separate plate, i = inreasing, d = dereasing. The set point is adjusted by turning the adjustment srew. To reah the adjustment srew for swithes with housing, remove the over. llow swith to reah the desired swith. Turn adjustment srew lokwise or ounterlokwise to atuate the miro swith. + Counterlokwise rotation: Clokwise rotation: set point inreasing set point dereasing Please onsult the wiring diagram for the ontat status at atmospheri (see Fig. 5). Preise adjustment of set point to atuate on inreasing Lower system to 0 bar. Inrease slowly and hek if miro swith is atuated at desired swith. If neessary, readjust by turning the adjustment srew Repeat preeding steps until miroswith operates at desired swith. Preise adjustment of set point to atuate on dereasing Inrease up to a point learly above the desired swith (at least, swith plus max. hysteresis; not above max. operating ). Lower slowly and hek if miro swith is atuated at desired swith. If neessary, readjust by turning the adjustment srew Repeat preeding steps until miroswith operates at desired swith. Following the adjustment of all set points, eah set point must be heked and, if neessary, be readjusted. Wiring Code for all Types (Contat status at atm. ) NC NC NO NO at vauum NC/NO vie versa Fig. 5: Wiring Code Power iruit 1 Power iruit 2 C = purple NC = blue NO = red C = brown NC = orange NO = blak Use in Hazardous Loations There are two housing designs for use in hazardous loations. The BX version with an explosion-proof enlosure for Ex d appliations. The Bourdon tube swithes with T and X housing are approved for use in intrinsially safe iruits as Ex ia. The intrinsially safe units marked as Ex i must be operated with a ertified swith amplifier (see Fig. 6). The B1S/B2S swith has none of the aforementioned TEX approvals. BX swithes with explosion-proof enlosures are designed and ertified to be used aording to UL, CS, Nema 4, 7, 9 or TEX regulations. The wiring between swith and Ex i isolation amplifier must meet the loal safety requirements. The ustomer must provide for a highly ondutive onnetion between swith and grounding. Unproteted area 1 2 Zener barrier type Swith amplifier NMUR Fig. 6: Operation of swithes in intrinsially safe areas NO NC Ex ia area GRD The adjustment of several set points ours for eah set point as speified above. 6 7
5 6 Maintenane/Cleaning Maintenane The swith is maintenane free. Cheking the set points lies within the disretion of the user. The usual preventive maintenane work in aordane with the PED and TEX guidelines must always be arried out. B1T 4 (1.4) 9 (0.5) 112 (4.41) 6 (1.42) Cable gland PG 1.5 (able diameter ø mm) (S version only) B2T Please note that small setpoint drifts may our during the initial use of the swith (run-in period). To minimize the setpoint drift we an perform a run-in (ageing) proess in our works on request. Larger or ontinuing setpoint drifts during the normal use of the swith may indiate that the measuring system is not used orretly within the speified limits, exeeding the design riteria or is worn-out. This might lead to metal fatigue of the measuring system and it therefore should be replaed before an ultimate rupture of the metal diaphragm might take plae. Please onsult your supplier or Barksdale diretly for guidelines. 7 Tehnial Data 1 (5.26) 149 (5.87) 190 (7.48) See data sheet Dimensions in mm (inh) leads about 450 (17.72) long B1S 40 (1.57) 6 leads about 450 (17.72) long B2S 40 (1.57) 12 (0.47) 4 (1.4) 71 (2.795) Proess onnetion 27 (1.06) 6.5 (0.26) Set srew SW under the lid 6.5 (0.26) 25 (0.98) 16 (0.6) 8 (0.15) (0.9) Ciruit 1 (0.9) Ciruit 2 Fig. 8: Bourdon tube swith type B1T.../B2T... * Slotted hex adjustment srew size 0 (1.18) max. 127 (5) 0 (1.18) max. 127 (5) 40 (1.575) 16 (0.6) SW 19 Proess onnetion ¼ NPT internal Slotted hex adjustment srew Ciruit 1* size Ciruit 2* Fig. 7: Bourdon tube swith type B1S.../B2S... Proess onnetion ¼ NPT internal 5 (0.197) Fig. 9: ø (0.12) UNF 9/ dapter, adjustable ranges*) see setion djustable Ranges Pressure Swith Type B1S /B2S and Type B1T /B2T and djustable Ranges Pressure Swith Type B1X /B2X 8 9
6 B1X B2X djustable Ranges Pressure Swith Type B1X /B2X Conduit onnetion ½ NPT Conduit onnetion ¾ NPT Mounting hole 65 (2.56) ø8 (1.496) 11 (0.4) Pressure range ode djustable range Max. operating Proof Max. hysteresis of swith types (end of range) 11 (0.4) 11 (0.4) 6.5 (1.47) 1 (4.) Fig. : Bourdon tube swith type B1X.../B2X... djustable Ranges Pressure Swith Type B1S /B2S and Type B1T /B2T Pressure range ode Over 21.5 (0.85) ø165 (6.496) djustment srew djustable range Inreasing 11 (0.4) 6.5 (1.47) 1 (4.) Dereasing 21,5 (0.85) ø165 (6.496) Ciruit 2 Ciruit 1 Max. operating Proof press. (short term) B.T B.S B.T B.S H, GH Max. hysteresis of swith types (end of range) M, GM 12SS ,96 1,86 65 (2.65) 127 (5) 8.5 (0.) SW (8.54) Proess onnetion ¼ NPT Over Inreasing Dereasing (short term) H, GH M, GM 12SS ,96 1,86 20SS ,68 5,44 2SS ,75 5,90 72SS* ,90 7,90 Eletrial Ratings Miro swith H M Speial Charateristis Miroswith with silver ontats Miroswith with silver ontats Volt C 50/60 Hz Ind. Res. Volt DC 6 to Ind. Res. Notes Small hysteresis; high C / low DC loads Medium hysteresis; high C and DC loads GH Miroswith with gold plated ,00 1,00 low hange-bak values GM ontats for low voltage and low urrent , 0, Medium hysteresis 2SS ,68 5,44 48SS ,75 5,90 65SS* ,58 7,92 120SS* ,90 7,90 180SS* ,90 7,90 We reommend to use a prefuse of the maximum urrent rating from the table above aording to the load swithed. We reommend gold plated ontats for all intrinsially safe and other appliations with low voltage/power. 11
Operating Instructions
Operating life time Normal expeted servie life (expressed in the number of yles over the full adjustment range) is appr. 1 million for the pressure swith. This may be extended to 2.5 million yles max.
More informationBKR: 3-way ball valve with female thread, PN 40
Regulating valves, ombined with atuator CV5.60 en Produt Data Sheet BKR015...050 BKR: 3-way ball valve with female thread, PN 40 ow energy effiieny is improved Preision ontrol and working without losses
More informationBKR: 3-way ball valve with female thread, PN 40
Regulating valves, ombined with atuator PDS 56.091 en Produt Data Sheet BKR015...050 BKR: 3-way ball valve with female thread, PN 40 ow energy effiieny is improved Preision ontrol and working without losses
More informationBUL: 3-way unit valve, PN 16
Produt data sheet 55.009 BU: 3-way unit valve, PN 16 Improving energy effiieny inear mixture and no loss through leakage in the ontrol passage for energy-effiient regulation Features Flat-sealing standard
More informationBKTA: 3-way change-over ball valve (T) with male thread, PN 40
BKTA: 3-way hange-over ball valve (T) with male thread, PN 40 ow energy effiieny is improved Effiieny means preise hangeover with minimum leakage Features 3-way hange-over ball valve with T-bore for use
More information55.109/1. BUT: Three-way unit valve, PN 16. Sauter Components
55.109/1 UT: Three-way unit valve, PN 16 How energy effiieny is improved Linear mixture and no leak losses in the ontrol passage for energy-effiient regulators. reas of appliation Regulating valve for
More informationBKR: 3-way regulating ball valve with female thread, PN 40
Produt data sheet 5.1 56.091 BKR: 3-way regulating ball valve with female thread, PN 40 ow energy effiieny is improved Effiieny means preise ontrol and working with minimum leakage Features 3-way regulating
More informationM-5071/1111. Electronic Pressure Switch PSW14 series
M-507/ Electronic Pressure Switch PSW4 series S TABLE OF CONTENTS Electronic Pressure Switch PSW4 Series Intended Applications... Safety Instructions... 3 Standards... 4 Warranty/Guaranty... 5 Installation/Commissioning...
More informationVKR: 2-way regulating ball valve with female thread, PN 40
Produt data sheet 7.1 56.090 VKR: 2-way regulating ball valve with female thread, PN 40 ow energy effiieny is improved Effiieny means preise ontrol and working with minimum leakage Features 2-way regulating
More informationSauter Components
55.009/1 U: Unit threeway valve, PN 1 How energy effiieny is improved inear mixing and no losses through leakage for energyeffiient ontrol. reas of appliation Control valve for ontrolling heating zones,
More information76.111/1. BUD: Flanged three-way valves, PN 6. Sauter Components
76.111/1 BUD: Flanged three-way valves, PN 6 ow energy effiieny is improved urate ontrol with high reliability. reas of appliation Continuous ontrol of old/hot water and air in losed networks 1) and flow
More informationVaccine Storage and Handling Guidelines
Vaine Storage and Handling Guidelines Table of Contents 2 Introdution 3 Definitions 3 The Importane of the Cold Chain 3 Proteting Ontario s Vaine Supply 4 Maintaining Vaine Poteny and Minimizing Wastage
More informationGeneral Technical Data and Calculations
18 Bosh Rexroth AG R31EN 232 (26.4) General Produt Desription General Tehnial Data and Calulations Fores and load moments In Rexroth the running traks are arranged at a ompression angle of 45. This results
More informationINSTRUCTION HANDBOOK OM2
INSTRUCTION HANDBOOK OM2 Pakaging mahine for sanitary napkins Mahine-No.: 2622668.11.01 Year of onstrution: 2007 Version 1 dated 2007-12-03 Keep for further referene! Manufaturer addresses / Customer servie
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 17.
The following exerpt are pages from the North Amerian Produt Tehnial Guide, Volume 2: Anhor Fastening, Edition 17. Please refer to the publiation in its entirety for omplete details on this produt inluding
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.
The following exerpt are pages from the North Amerian Produt Tehnial Guide, Volume 2: Anhor Fastening, Edition 16. Please refer to the publiation in its entirety for omplete details on this produt inluding
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.1.
The following exerpt are pages from the North Amerian Produt Tehnial Guide, Volume 2: Anhor Fastening, Edition 16.1. Please refer to the publiation in its entirety for omplete details on this produt inluding
More informationAnalysis of a Twin Screw Expander for ORC Systems using Computational Fluid Dynamics with a Real Gas Model
Purdue University Purdue e-pubs International Compressor Engineering Conferene Shool of Mehanial Engineering 2014 Analysis of a Twin Srew Expander for ORC Systems using Computational Fluid Dynamis with
More informationGAS PRESSURE REGULATOR RMG 512
SERVING THE GAS INDUSTRY WORLDWIDE General Desription GAS PRESSURE REGULATOR RMG 512 RMG REGEL + MESSTECHNIK GMBH Appliation, Features, Tehnial data Appliation for offtake stations in gas transmission
More informationTechnical Data. Dimensions
0102 Model Number Features 10 mm flush Shielded PUR cable for oil and gas sector Accessories BF 30 Mounting flange, 30 mm Technical Data specifications Switching function Normally closed (NC) Output type
More informationTechnical Data. General specifications. Rated operating distance s n 2 mm
0102 Model Number Features 2 mm flush Usable up to SIL 2 acc. to IEC 61508 Technical Data specifications Switching function Normally closed (NC) Output type NAMUR Rated operating distance s n 2 mm Installation
More informationInductive slot sensor
0102 Model Number Features 3.5 mm slot width Usable up to SIL 3 acc. to IEC 61508 Nonferrous targets Application Danger! In safety-related applications the sensor must be operated with a qualified fail
More informationTechnical Data. General specifications Switching element function Rated operating distance s n 2 mm
0102 Model Number Features 2 mm flush Usable up to SIL 2 acc. to IEC 61508 Accessories EXG-12 Quick mounting bracket with dead stop BF 12 Mounting flange, 12 mm Technical Data specifications Switching
More informationTechnical Data. General specifications. Rated operating distance s n 5 mm
0102 Model Number Features 5 mm flush Usable up to SIL 2 acc. to IEC 61508 Accessories EXG-18 Quick mounting bracket with dead stop BF 18 Mounting flange, 18 mm Technical Data specifications Switching
More informationTechnical Data. General specifications Switching element function Rated operating distance s n 1.5 mm
0102 Model Number Features 1.5 mm flush Accessories BF 8 Mounting flange, 8 mm Technical Data specifications Switching element function NAMUR, NC Rated operating distance s n 1.5 mm Installation flush
More informationTechnical Data. Dimensions
0102 Model Number Features Comfort series 15 mm non-flush Stainless steel housing Accessories BF 30 Mounting flange, 30 mm Technical Data specifications Switching element function NAMUR, NC Rated operating
More informationDimensions. Technical Data General specifications Switching element function Rated operating distance s n 5 mm
Dimensions M18x1 37 40 4 0102 24 LED Model Number Features 5 mm embeddable Usable up to SIL2 acc. to IEC 61508 Connection BN BU Accessories L+ L- EXG-18 Quick mounting bracket with dead stop BF 18 Mounting
More informationDimensions. Technical Data General specifications Switching element function Rated operating distance s n 10 mm
Dimensions M30x1,5 5 40 37 0102 Model Number 36 LED Features Comfort series 10 mm embeddable Connection BN BU Accessories BF 30 Mounting flange, 30 mm L+ L- Technical Data specifications Switching element
More informationPressure control, differental pressure control and thermostat Type RT
MAKING MODERN LIVING POSSIBLE Technical brochure Pressure control, differental pressure control and thermostat Type RT Hydrocarbons www.danfoss.com/hydrocarbons Contents Page Introduction...3 Approvals...3
More informationPressure Measurement. Transmitters for basic requirements SITRANS P Z for gauge pressure. 2/4 Siemens FI Overview
f gauge pressure Siemens AG 010 Overview Design The main components of the pressure transmitter are: Brass housing with silicon measuring cell and electronics plate Process connection Electrical connection
More informationRoboGolf (aka RoboPutting) Robofest 2016 Game
RooGolf (aka RooPutting) Roofest 201 Game 12-2-2015 V1.1 (Kik-off version. Offiial Version will e availale on Jan 8, 201) 4 3 2 1 a A. Game Synopsis Figure 1. RooGolf Playing Field (Jr. Division) There
More informationRESPIRATORY PROTECTIVE EQUIPMENT
RESPIRATORY PROTECTIVE EQUIPMENT SETTING Correspondene to: Dr R M Howie, 12 Morningside Close, Edinburgh EH10 4DB, UK; robin.howie@ btlik.om T RMHowie Oup Environ Med 2005; 62:423 428. doi: 10.1136/oem.2002.004424
More informationmanual h/p/cosmos discovery 4.0 Instruction- & Service manual Manufacturer h/p/cosmos sports & medical gmbh h/p/cosmos discovery 4.
manual h/p/osmos disovery 4.0 Instrution- & Servie manual Manufaturer h/p/osmos disovery 4.0 h/p/osmos sports & medial gmbh Firmware version 3.01.3 Am Sportplatz 8 DE 83365 ussdorf-traunstein Germany phone
More informationDimensions. Technical Data General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm
Dimensions 65 GW2 40 35 9 5 GW1 14 11 9 5.4 M20 x 1.5 0102 Model Number S M12 x 1.5 Features 77.5 LED V Direct mounting on standard actuators Compact and stable housing with terminal compartment connection
More informationTechnical Data. General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm. Short-circuit protection
0102 Model Number Features Direct mounting on standard actuators Compact and stable housing Fixed setting EC-Type Examination Certificate TÜV99 ATEX 1479X Usable up to SIL2 acc. to IEC 61508 Accessories
More informationPressure switch, Differential pressure switch and Thermostat RT-E
Data sheet Pressure switch, Differential pressure switch and Thermostat RT-E The RT-E series consist of pressure and differential pressure switches as well as thermostats. The units are designed for industrial
More informationSITRANS P measuring instruments for pressure
SITRANS P measuring instruments for pressure Z series for gage pressure Siemens AG 008 Overview Design The main components of the pressure transmitter are: Brass housing with silicon measuring cell and
More informationTechnical Data. Dimensions
00 Model Number Features mm flush Usable up to SIL acc. to IEC 6508 Accessories V-G Female connector, M, -pin, field attachable V-W Female connector, M, -pin, field attachable V-G-N-M-PUR Female cordset,
More informationTechnical Data. Dimensions
00 Model Number Features Comfort series 30 mm non-flush Accessories MHW 0 Modular mounting bracket V-G Female connector, M, 4-pin, field attachable V-W-N-M-PUR Female cordset, M, -pin, NAMUR, PUR cable
More informationRTA Series 1 4 Poles Coded Rotary Switches
1 4 Poles oded Switches Features/Benefits PB or hand soldering versions Bushing mounting Multiple poles Decimal and hexadecimal codes Screwdriver slot or extended actuator RoHS ompliant Typical Applications
More informationInstallation Instructions
Low -Ambient Pressure Switch 0201R22 0301410 Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY ONSIDERATIONS Improper installation, adjustment,
More informationTechnical Data. Dimensions
0102 Model Number Features Comfort series 5 mm flush Usable up to SIL 2 acc. to IEC 61508 Accessories BF 18 Mounting flange, 18 mm EXG-18 Quick mounting bracket with dead stop Technical Data specifications
More informationTechnical Data. General specifications Switching element function Rated operating distance s n 5 mm
00 Model Number Features 5 mm flush Usable up to SIL acc. to IEC 6508 Accessories V-G Female connector, M, -pin, field attachable V-W Female connector, M, -pin, field attachable V-G-N-M-PUR Female cordset,
More informationElectropneumatic Positioner and Pneumatic Positioner Type 3760 JIS
Electropneumatic Positioner and Pneumatic Positioner Type 3760 Application Single-acting positioners for direct attachment to pneumatic control valves. An electric standardized signal of 4 to 20 ma or
More informationLMP 307. Stainless Steel Probe. Stainless Steel Sensor. accuracy according to IEC 60770: standard: 0.35 % FSO option: 0.25 % / 0.
LMP 07 Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 % / 0. % FSO Nominal pressure from 0... mho up to 0... 50 mho Output signals -wire: 4... 0 ma -wire: 0...
More informationTechnical Data. Dimensions
0102 Model Number Features 6 mm flush Usable up to SIL 3 acc. to IEC 61508 Application Danger! In safety-related applications the sensor must be operated with a qualified fail safe interface from Pepperl+Fuchs,
More informationRTA Series 1 4 Poles Coded Rotary Switches
1 4 Poles oded Switches Features/Benefits PB or hand soldering versions Bushing mounting Multiple poles Decimal and hexadecimal codes Screwdriver slot or extended actuator RoHS ompliant Typical Applications
More informationRules of Hockey5s including explanations
Rules of Hokey5s inluding explanations Effetive from 1 January 2015 (updated 18 May 2015) Copyright FIH 2015 The International Hokey Federation Rue du Valentin 61 CH 1004, Lausanne Switzerland Telephone:
More informationEMPLOYER SAMPLE PROCEDURES FOR HEAT ILLNESS PREVENTION
EMPLOYER SAMPLE PROCEDURES FOR HEAT ILLNESS PREVENTION FEB 2010 California Employers with any outdoor plaes of employment must omply with the Heat Illness Prevention Standard T8 CCR 3395. These proedures
More information1 Overview. Pressure Measurement Transmitters for basic requirements. 1/16 Siemens FI SITRANS P220 for gauge pressure
Siemens AG 204 Overview The pressure transmitter SITRANS P220 measures the gauge pressure of liquids, gases and vapors. Stainless steel measuring cell, fully welded Measuring ranges 2.5 to 600 bar (36.3
More informationOwners Manual Models 4430BF3, 4430BF2 & 4430BF1 Floor Mounted Tri-Level Bottle Filling Tubular Fountain
Owners Manual Models 4430F3, 4430F2 & 4430F1 Floor Mounted Tri-Level ottle Filling Tubular Fountain MODEL 4430F1L MODEL 4430F2UM INSTALLER 4430F Fountains are among the easiest to install Fountains on
More informationCompact differential pressure switch Flameproof enclosure Ex d Models DE, DEC
Mechatronic pressure measurement Compact differential pressure switch Flameproof enclosure Ex d Models DE, DEC WIKA data sheet PV 35.41 Process Compact Series Applications Differential pressure monitoring
More informationTechnical Data. Dimensions
0102 Model Number Features Comfort series 15 mm flush Accessories MHW 01 Modular mounting bracket MH 04-2057B Mounting aid for VariKont and +U1+ V1-G-N-2M-PUR Female cordset, M12, 2-pin, NAMUR, PUR cable
More informationElectropneumatic Positioner Type 4763 Pneumatic Positioner Type 4765
Electropneumatic Positioner Type 4763 Pneumatic Positioner Type 4765 Application Single-acting positioner for attachment to pneumatic control valves. Supplied with either an electric input signal from
More informationITS 300 & 500 SERIES POSITION MONITORING INSTALLATION AND OPERATION MANUAL
ITS 300 & 500 SERIES POSITION MONITORING ITS 300 & 500 SERIES POSITION MONITORING INSTALLATION AND OPERATION MANUAL (Explosion proof Ex d II T6) (Doc no: ITS00312-M) 74-6, hun Ui-Dong, Won Mi-Gu, Bucheon
More informationPressure switch KP-E. Data sheet
Data sheet Pressure switch KP-E KP-E pressure switches for use in refrigeration and air conditioning systems are equipped with SPDT gold plated contacts and stainless steel bellows. The high pressure switches
More informationActuating elements for ComEx
Description A large number of variants and versions of actuating elements are available for the ComEx control and indicator units. All actuating elements are made of high-quality thermoplastic and conform
More informationMagnetic level switch type MR783 Instruction Manual
Magnetic level switch Magnetic level switch type MR783 1. DESCRIPTION page 3 1.1 Operation page 3 1.2 Application page 3 1.3 Description page 3 2. SPECIFICATIONS page 3 2.1 Service Conditions page 4 2.2
More informationElectropneumatic Positioner and Pneumatic Positioner Type 3760 JIS
Electropneumatic Positioner and Pneumatic Positioner Type 3760 Application Single-acting positioners for direct attachment to pneumatic control valves. Supplied with an electric input signal of 4 to 20
More informationTechnical Data. Dimensions
0102 Model Number Features 2 mm flush Usable up to SIL2 acc. to IEC 61508 Technical Data specifications Switching element function NAMUR, NC Rated operating distance s n 2 mm Installation flush Output
More informationEXHIBITOR MANUAL. Organiser
EXHIBITOR MANUAL 2018 Organiser ABOUT THE EXHIBITION Exhibition Name : 22nd EAST MEDITERRANEAN INTERNATIONAL TOURISM & TRAVEL EXHIBITION - EMITT Exhibition Conept : International Tourism and Travel Exhibition
More informationRules of Beach Hockey including explanations
Rules of Beah Hokey inluding explanations Effetive from 1 June 2016 (updated 31 May 2016) Copyright FIH 2016 The International Hokey Federation Rue du Valentin 61 CH 1004, Lausanne Switzerland Telephone:
More information1 Overview. Pressure Measurement Single-range transmitters for general applications. 1/16 Siemens FI US Edition
Siemens AG 206 Overview Design Device structure without explosion protection The pressure transmitter consists of a piezoresistive measuring cell with a diaphragm installed in a stainless steel enclosure.
More informationGeneral Specifications
General Speifiations Model GC8000 Proess Gas Chromatograph GS 11B08A01-01E GENERAL A Proess Gas Chromatograph analyzes a vapor or volatile liquid sample and then separates the various hemial omponents
More informationPressure Measurement Single-range transmitters for general applications
Siemens AG 206 Overview Design Device structure without explosion protection The pressure transmitter consists of a piezoresistive measuring cell with a diaphragm installed in a stainless steel enclosure.
More informationInstallation Instructions
Installation Instructions Low-Ambient Pressure Switch KSALA0201R22 KSALA0301410 NOTE: Read the entire instruction manual before starting the installation. SAFETY ONSIDERATIONS Improper installation, adjustment,
More informationPressure Switches Application Guideline
Pressure Switches Application Guideline Product Overview The Fema Pressure Switch product portfolio provides devices suitable for many applications. The portfolio contains Special functions and equipment
More informationDMK 458. Pressure Transmitter for Marine and Offshore. Ceramic Sensor. accuracy according to IEC 60770: standard: 0.25 % FSO option: 0.
Pressure Transmitter for Marine and Offshore Ceramic Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0. % FSO Nominal pressure from 0... 40 mbar up to 0... 0 bar Output signals -wire:
More informationElectro-Pneumatic Converter YT-940 SERIES
Electro-Pneumatic Converter YT-940 SERIES PRODUCT MANUAL VERSION 1.00 Contents 1. Introduction 3 1.1 General information for the users. 3 1.2 Manufacturer Warranty 3 1.3 Explosion Proof Warning. 4 2. Product
More informationOPTIBAR P 1010 C Technical Datasheet
Technical Datasheet Pressure transmitter with recessed diaphragm for general applications Wide variety thanks to modular design Measuring ranges up to 250 bar / 3750 psi High overload and temperature stability
More informationSITRANS. Pressure transmitter SITRANS P, Z series for gauge and absolute pressure. Introduction. Safety instructions 2.
Introduction 1 Safety instructions 2 SITRANS Pressure transmitter SITRANS P, Z series for gauge and absolute pressure 7MF1564 Description 3 Assembly and connection 4 Technical data 5 Dimensional drawings
More informationDimensions. Technical Data General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm
Dimensions 7 36 5 33.5 9 5.4 30 65 0102 Model Number Features Direct mounting on standard actuators Fixed setting Satisfies machinery directive Compact and stable housing EC-Type Examination Certificate
More informationAir Sensor. SAC Ex. Manual ATEX. AQ Elteknik AB
Air Sensor SAC Ex Manual AQ Elteknik AB ATEX Air Sensor SAC Ex ATEX Certified model Manual version 2.1 April 2014 AQ Elteknik AB 2 Table of contents 1. Manufacturer information... 4 Manufacture Declaration
More informationOperating Instructions
Operating Instructions Ex d Enclosures in Light Metal / Flameproof Encapsulation > 8265/0 Empty Enclosure > 8265/4 controller, installed in Ex e enclosure > 8265/5 controller Contents 1 Contents 1 Contents...2
More informationMiniature flowmeters DK 46, DKR 46 DK 47, DK 48, DK 800
KROHNE 1/22 7.236.22. GR Miniature flowmeters DK 46, DKR 46 DK 47, DK 48, DK 8 Variable area flowmeters Vortex flowmeters Flow controllers Electromagnetic flowmeters Ultrasonic flowmeters Mass flowmeters
More informationRules of Hockey5 including explanations
Rules of Hokey5 inluding explanations Effetive from 1 September 2012 Copyright FIH 2012 The International Hokey Federation Rue du Valentin 61 CH 1004, Lausanne Switzerland Telephone: ++41 21 641 0606 Fax:
More informationLSA 42.2 /43.2 / & 4 P
3542 en - 9.27 / d Alternators 11.5... 3 kva - 2 Pole 12... 135 kva - 4 Pole SA 42.2 / 43.2 / 44.2-2 & 4 P Single phase dedicated Electrical and mechanical data SA 42.2 /43.2 / 44.2-2 & 4 P Single phase
More informationType N-10, N-11 Hazardous Area Non-incendive Transmitters
Electronic Pressure Catalog > Hazardous Area > N-10, N-11 Type N-10, N-11 Hazardous Area Non-incendive Transmitters Applications Natural gas compressors Wellhead monitoring Pipeline pressure General industrial
More informationPosition switches FP series
A Position switches FP series Selection diagram 0 08 8 9 0 0 0 Ø 8 mm Ø, mm external rubber stainless steel stainless steel fiber glass rod gasket sphere sphere adjustable lever safety adjustable lever
More informationFurther technical information is available on
1 of 5 Manufacture address : Bartec Technor AS Dusavikveien 39 4007 Stavanger Norway Further technical information is available on www.bartec-technor.no Note on instructions When working in hazardous areas,
More information3.1. Ex-e/i Cable Glands Plastic version for Zone 1, 2, 21 and according to EN : 2012
.1 x-e/i Cable Glands Plastic version for Zone 1, 2, 21 and 22 1 - according to N 60079-0: 2012 Conform with latest standards Cable glands with metric screwin threads are now standard and had replace the
More informationLiquid level instruments BM 24 /BM 51
KROHNE 09/2001 7.02362.21.00 GR/PRINTO Liquid level instruments / Status: 10/99 Variable area flowmeters Vortex flowmeters Flow controllers Electromagnetic flowmeters Ultrasonic flowmeters Mass flowmeters
More informationOSAT Series. Intrinsically Safe Infrared Temperature Sensor Operator's Guide
OSAT Series Intrinsically Safe Infrared Temperature Sensor Operator's Guide Issue L Jan 2017 Introduction OSAT Series intrinsically safe non-contact infrared temperature sensors measure the temperature
More informationInstruction Manual AD 1000 / BA 1000 Absolute Pressure Sensor
Instruction Manual AD 1000 / BA 1000 Absolute Pressure Sensor halstrup-walcher GmbH Stegener Straße 10 D-79199 Kirchzarten Phone: +49 (0) 76 61/39 63 0 Fax: +49 (0) 76 61/39 63 99 E-Mail: info@halstrup-walcher.com
More information1 Overview. Pressure Measurement Single-range transmitters for general applications. 1/22 Siemens FI US Edition
Siemens AG 07 SITRANS LH00 Transmitter for hydrostatic level Overview Function U const. p U I EM The pressure transmitter SITRANS LH00 is a submersible sensor for hydrostatic level measurement. The pressure
More informationIKGAtl Kenneth Grubb Associates Ltd
IKGAtl Kenneth Grubb Assoiates Ltd BURO HAPPOLD COPPERHOUSE SLUICE GATE DOCUMENT REVISION RECORD Doument Number: Number of Pages: Doument Title: Saved as: C0395/006/DOC 31 REPORT ON THE MECHANICAL SURVEY
More informationOperating Instructions
Operating Instructions Light-metal Ex d enclosures / flameproof enclosure > 8265/0 Empty enclosure > 8265/4 Control panel, integrated in Ex e enclosure > 8265/5 Control panel Table of Contents 1 Table
More informationDimensions. Technical Data General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm
Dimensions 65 9 5 14 40 35 11 9 5.4 M20 x 1.5 0102 S Model Number Features Direct mounting on standard actuators Compact and stable housing with terminal compartment connection Fixed setting Satisfies
More informationHigh-performance submersible pressure transmitter For level measurement Model LH-20
Electronic pressure measurement High-performance submersible pressure transmitter For level measurement Model LH-20 WIKA data sheet PE 81.56 Applications Deep well and borehole measurements Groundwater
More informationHigh-performance submersible pressure transmitter For level measurement Model LH-20
Electronic pressure measurement High-performance submersible pressure transmitter For level measurement Model LH-20 WIKA data sheet PE 81.56 Applications Deep well and borehole measurements Groundwater
More information4/2 way Pneumatic Solenoid Valve
4/2 way Pneumatic Solenoid Valve Compact design Push-over solenoid coil Exhaust air can be regulated Tube, threaded and sub-base connections Type combined with Seat valve version Type 2508 Type 2510/11
More informationQPL... Pressure Switches. Siemens Building Technologies HVAC Products
7 221 Pressure Switches QPL... The pressure switches are used for monitoring gas or air pressures. When the pressure falls below the switching point, the associated electrical circuit will open or switch
More informationPressure Switch for gas and air GGAO-A4
Pressure Switch for gas and air GGAO-A4 CSA Certified CSA C22.2 No. LR 53222 Certification file # 201527 Commonwealth of Massachusetts Approved Product Approval code G3-0106-191 Gas pressure switch Codes
More informationEX-RECESSED CEILING LIGHT FITTINGS
EX-RECESSED CEILING LIGHT FITTINGS RLF/RLF-INOX 250 18-58 W / RLF/RLF-INOX 250... N 18-36 W Metallic design for Zone 1 and Zone 21 The RLF... explosion-protected recessed ceiling light fittings with electronic
More informationAPPENDICES STRANDJACK WEDGES Friction coefficients, micro slip and handling
APPENDICES STRANDJACK WEDGES Frition oeffiients, miro slip and handling Report nr. DCT 2005-78 By: H.G.M.R. van Hoof Idnr : 501326 20 November, 2005 Researh strand jak wedges Appendies By H.G.M.R. van
More informationHH Coil Split 2V2T. 3X3-03 Free-Way Switch BRIDGE NECK. Grd To Bridge. Tone. Vol. Tone. Vol. (Tip) (Sleeve) Single Coil
Grd To Positions 4, 5 & 6 voie the slug oils on normal humbukers by grounding the oil link onnetions. Use multi-ore sreened able between swith and ontrols on 'Link' wires would normally be onneted for
More informationOperating instructions Safety Rope Emergency Stop Switches ZB0052 / ZB0053 ZB0072 / ZB0073
Operating instructions Safety Rope Emergency Stop Switches UK ZB0052 / ZB0053 ZB0072 / ZB0073 7390878 / 02 03 / 2011 Contents 1 Safety instructions...3 2 Installation / set-up...4 2.1 Applications...4
More information1 Overview. Pressure Measurement Single-range transmitters for general applications. 1/22 Siemens FI
Siemens AG 06 SITRANS LH00 Transmitter for hydrostatic level Overview Function U const. p U I EM The pressure transmitter SITRANS LH00 is a submersible sensor for hydrostatic level measurement. The pressure
More informationNote: the lock-out circuit must be in accordance with Section 8.7 of DIN/VDE Twin thermostats ATH.-SW-2020 ATH.-SW-2070 ATH.
M. K. JUCHHEIM GmbH & Co Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 3603 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-60 E-mail: mail@jumo.net Internet: www.jumo.net
More informationEx-proof solenoid valves with spool position monitor on/off, with inductive proximity sensor - Multicertification ATEX, IECEx, EAC
www.atos.com Table -2/E Ex-proof solenoid valves with spool position monitor on/off, with inductive proximity sensor - Multicertification TEX, IEEx, E valve body spool ex-proof solenoid ex-proof inductive
More information