Gas-liquid flow optimization with a Bubble Breaker device

Transcription

1 35 th Gas-Lift Workshop Houston, Texas, USA February 6 10, 2012 Gas-liquid flow optimization with a Bubble Breaker device Hendy T. Rodrigues, Petr. Eng. Petrobras Research Center Feb. 6-10, Gas-Lift Workshop 1

2 Petrobras R&D Center, Rio de Janeiro Feb. 6-10, Gas-Lift Workshop 2

3 Introduction Bubble breaker was first presented by Shell engineers (Schrama and Fernandes, 2005): Experimental and field tests Objective is to break the bubbles into smaller diameters, or change the flow pattern

4 Motivation Smaller bubbles reduce hidrostatic pressure drop and delay the transition to slug flow (Guet et. al., 2003)

5 Motivation Lower rise velocity Greater void fraction lower hidrostatic pressure gradient. ρ = ρ α + ρ 1 G L ( α ) α = Q G A V G

6 Motivation Bubble rise velocity increases with bubble diamenter. D~1,5mm D~17mm (Celata et. al., 2007) (Parkinson et. al., 2008) (Tomiyama et. al., 2002) (Nguyen et. al., 1998)

7 Experiments This work presents experimental results to evaluate the device: Pressure measurements: At four locations along the pipe. Ratio of Pressure Gradients before and after the bubble breaker. R=(Press. Grad. After)/(Press. Grad. Before) Detailed videos: high-speed camera.

8 Experimental facilities

9 Bubble breaker 3 different geometries: 1 plate with orifices and 2 Venturi

10 Test conditions Test conditions: 1000 Q L = 6 21 L/min Q G = 9 90 L/min Air and water QL (L/min) 100 Disperse bubbles 10 Slug QG (L/min)

11 Videos Dispersed bubbles One elongated bubble Slug flow

12 Pressure loss results QL=6 L/min Orifícios 8x3mm Venturi 8,5mm Venturi 6mm QL=12 L/min Orifícios 8x3mm Venturi 8,5mm Venturi 6mm P (kgf/cm2) P (kgf/cm2) QG local (l/min) QG local (l/min) QL=16,8 L/min Orifícios 8x3mm Venturi 8,5mm Venturi 6mm QL=21 L/min Orifícios 8x3mm Venturi 8,5mm Venturi 6mm P (kgf/cm2) P (kgf/cm2) QG local (l/min) QG local (l/min)

13 Pressure gradients ratio QL=6 L/min QL=12 L/min Orifícios 8x3mm Venturi 8,5mm Venturi 6mm QG local (l/min) QL=21 L/min Orifícios 8x3mm Venturi 8,5mm Venturi 6mm 1.2 R R R Orifícios 8x3mm Venturi 8,5mm Venturi 6mm QG local (l/min) QL=16,8 L/min Orifícios 8x3mm Venturi 8,5mm Venturi 6mm 1.2 R QG local (l/min) QG local (l/min) Values of R lower than 1 indicates that the Bubble Breaker is effective!

14 Results Bubble breaker is more effective at the Disperse Bubbles flow pattern (higher liquid flow rates). Geometry should be studied for each application. Reduction in the Pressure Gradients must be compared to local pressure drop. Next works: Different geometries to enhance bubble breaking while reducing local pressure drop.

15 References 1 Schrama, E. and Fernandes, R. The bubble breaker: breaking up slug flow into dispersed bubbly flow using a passive mechanical device. BHR Group 2005 Multiphase Production Technology 12 2 Guet, S., Ooms, G., Oliemans, R. V. A. and Mudde, R. F. Bubble Injector Effect on the Gaslift Efficiency AIChE Journal, Vol. 49, No. 9, Celata, G. P., D Annibale, F., Di Marco, P., Memoli, G. and Tomiyama, A. Measurements of rising velocity of a small bubble in a stagnant fluid in one- and two-component systems Exp. Thermal and Fluid Sciences, Vol. 31, Parkinson, L., Sedev, R., Fornasiero, D. and Ralston, J. The terminal rise velocity of μm diameter bubbles in water Journal of Colloid and Interface Science, Vol. 322, Tomiyama, A., Celata, G. P., Hosokawa, S. and Yoshida, S. Terminal velocity of single bubbles in surface tension force dominant regime Int. J. of Multiphase Flow, Vol. 28, Nguyen, A. V. Prediction of Bubble Terminal Velocities in Contaminated Water AIChE Journal, Vol. 44, No. 1, 1998.

16 Copyright Rights to this presentation are owned by the company(ies) and/or author(s) listed on the title page. By submitting this presentation to the Gas-Lift Workshop, they grant to the Workshop, the Artificial Lift Research and Development Council (ALRDC), and the American Society of Mechanical Engineers (ASME), rights to: Display the presentation at the Workshop. Place it on the web site, with access to the site to be as directed by the Workshop Steering Committee. Place it on a CD for distribution and/or sale as directed by the Workshop Steering Committee. Other uses of this presentation are prohibited without the expressed written permission of the company(ies) and/or author(s) who own it and the Workshop Steering Committee. Feb Gas-Lift Workshop 16

17 Disclaimer The following disclaimer shall be included as the last page of a Technical Presentation or Continuing Education Course. A similar disclaimer is included on the front page of the Gas-Lift Workshop Web Site. The Artificial Lift Research and Development Council and its officers and trustees, and the Gas-Lift Workshop Steering Committee members, and their supporting organizations and companies (here-inafter referred to as the Sponsoring Organizations), and the author(s) of this Technical Presentation or Continuing Education Training Course and their company(ies), provide this presentation and/or training material at the Gas-Lift Workshop "as is" without any warranty of any kind, express or implied, as to the accuracy of the information or the products or services referred to by any presenter (in so far as such warranties may be excluded under any relevant law) and these members and their companies will not be liable for unlawful actions and any losses or damage that may result from use of any presentation as a consequence of any inaccuracies in, or any omission from, the information which therein may be contained. The views, opinions, and conclusions expressed in these presentations and/or training materials are those of the author and not necessarily those of the Sponsoring Organizations. The author is solely responsible for the content of the materials. The Sponsoring Organizations cannot and do not warrant the accuracy of these documents beyond the source documents, although we do make every attempt to work from authoritative sources. The Sponsoring Organizations provide these presentations and/or training materials as a service. The Sponsoring Organizations make no representations or warranties, express or implied, with respect to the presentations and/or training materials, or any part thereof, including any warrantees of title, noninfringement of copyright or patent rights of others, merchantability, or fitness or suitability for any purpose. Feb. 6 10, Gas-Lift Workshop 17