Down and Out Mount Assembly & Installation Directions

Transcription

1 Dwn and Out Munt Assembly & Installatin Directins Munting the Dwn and Out Munt crrectly takes a lt f thught and a lt f planning. Please read the directins thrughly and plan ut hw the munt wuld be installed best fr yur use. Each Setup will be different and these directins cannt accunt fr every situatin. Failure t d s may result in Damage, Injury, r Death. Dynamic Munting is nt respnsible fr any damage, injury, r death resulting frm imprper munting r use f the Dwn and Out Munt. These instructins are nly a guide and the cnsumer is respnsible fr crrect and secure munting. The persn installing the munt shuld be a cmpetent persn with experience munting lad bearing assemblies. Fr any questins r cncerns, please cntact Dynamic Munting at Inf1@DynamicMunting.cm. CAUTION: This wall munt is intended fr use nly with the maximum weight f 125 lbs. Use with heavier than the maximum weights indicated may result in instability causing pssible injury. ATTENTION: Ce supprt mural est destiné à être utilisé uniquement avec le pids maximum de 56.7 kgs. Utiliser avec plus lurds que les pids maximaux indiqués peut entraîner une instabilité et prvquer des blessures. Ptential Heat Damage: Dynamic Munting takes n respnsibility fr damage caused frm the fireplace r ther heating surces t the televisin, munt, r ther accessries. Damage culd be dne when the munt is dwn, ut, r even up. It is up t the cnsumer t take the prper precautins t avid damage. Electrical equipment can verheat easier than expected. Dynamic Munting recmmends against having fires in the fireplace whenever there is electrical equipment arund. Nte: D NOT mve mre than half f yur TV belw a mantel lcated abve a fireplace. When munting the Dwn and Out Recess Munt ver a fireplace with a mantel, d NOT install the Munt such that mre than half f yur TV can be mved belw the mantel. Specificatins Fits mst Flat and Curved Televisins 40 inches and larger t 125 lbs. Check televisin weight and munting hle pattern fr cmpatibility with yur televisin Nte fr smaller televisins; the munt may be wider r taller than the televisin. If this is the case then the munt may be visible in the tp psitin. See Figure 1 Handles televisins 20 t 125 lbs Allwable televisin munting pattern: 6.7in (170mm) t 27.2in (692mm) wide, up t 22.8in (579mm) high. Wrks with all VESA patterns in that range, See Figure 1 Prduct Dimensins: 29.0 x 23.6 x 3.9 inches. See Figure 1 Prduct Weight: 24 punds Tilts 7 degrees t Vertical in tp psitin Tilt can be fine-tuned Vertical +/-1 degree in ut thrugh bttm psitin FAQ Where d I munt ver a shelf? See the Abve Shelf Munting sectin n page 7. Munt is really hard t mve/actuate. See the Adjusting the Cunterbalance sectin n page 8. The TV tilts dwn in the tp psitin. See the Setting the Tilt in the Tp Psitin sectin n page 9. The TV isn t level in all psitins. When attaching t the wall, level ff f the Hk Plate Edge, NOT the plate that attaches t the wall, see Figure 6 n page 5. The TV isn t level in the ut and bttm psitins. The TV s Center f Gravity needs t be centered n the munt, if the stud spacing isn t allwing this t happen the Extra Wall Supprt (sld separately) extends the munts reach and wuld prbably help. Install Vide at 1

2 CAUTION: These wall munting instructins and hardware are fr munting t wd studs nly. It is up t yu t verify that the material supplied will wrk fr yur setup; ther materials may need t be purchased by yu. Fr cncrete, brick r ther munting materials cnsult an expert. Cnsult yur TV s wner manual befre munting yur televisin, it cntains relevant infrmatin. Tls Needed 7/16 pen ended wrenches 9/16 inch bx r ratchet wrench 1/4 inch Drill Bit Drill Tape Measure Stud Finder Level Phillips Screwdrivers A friend r 2, depending n hw heavy yur televisin is Parts Included 1 Dwn and Out Munt (Tw Stud Versin, unless Addendum Included) 2 TV Hangers with Washer and Screw 2 Paintable Plastic Cvers Varius Items (All in One Bag) 4 3/8 inch by 3 inch lng lag screw with washer 4 Zip Ties 2 Adhesive Rubber Bumpers 4 Lag Screw Cver 4 Washer fr Lag Screw Cver Fasteners fr Munting the Televisin t the TV Hangers (All in One Bag) 4 M6 x 20 mm (.78in) lng Phillips head machine screw 4 M6 x 35 mm (1.38in) lng Phillips head machine screw 4 M8 x 20 mm (.78in) lng Phillips head machine screw 4 M8 x 35 mm (1.38in) lng Phillips head machine screw 8 1/4 inch tall plastic spacers 4 1/8 inch tall plastic spacers 4 Steel M6 washers Table f Cntents Determining Where t Put Munt... 4 Attaching TV Hangers t Televisin... 4 Cnditins fr Munting t Wall... 4 Munting T Wall... 5 Attaching the Televisin t the Munt... 6 Psitins Munt Will Stay At... 6 Mving the Televisin Up and Dwn... 6 Abve Shelf Munting... 7 Tips t get the Lwest Pssible Bttm Psitin... 7 Adjusting the Cunterbalance... 8 Bump Stp... 8 Setting the Tilt in the Tp Psitin... 9 Setting the Tilt in the Bttm and Out Psitins... 9 Rubber Bumpers... 9 Paintable Plastic Cvers... 9 Wire Management...10 Maintenance...10 Warranty...10 Install Vide at 2

3 Figure 1, Munt Overall Size, Televisin Munting Hle Pattern Range, Wall Munting Hle Pattern Range Nte: Munt Only Cmes with 2 televisin Munting Arms, Nt the 4 Shwn Figure 2, Vertical in Tp Psitin Vertical tlerance in Out and Bttm Psitins is +/-1 degree. Figure 3, Max Tilt (7 Degrees) in Tp Psitin Install Vide at 3

4 Determining Where t Put Munt 1. Extra thught and planning is needed when munting ver a shelf; see the Abve Shelf Munting sectin n page 7 fr mre details and relevant dimensins. Find the needed distances [H] and [C] fr yur shelf depth [D]. 2. T find ut hw the munt relates t the televisin yu shuld d a test fitting n the grund. 3. If attaching a speaker lay that ut als with the speaker bracket. 4. Figure 4 shws the imprtant things t lk fr and measure. 5. If munting ver a shelf, make sure the [H] and [C] minimum distances are satisfied. Figure 4, Munt Test Fitting Attaching TV Hangers t Televisin Figure 5, Attaching TV Hangers t TV Cnditins fr Munting t Wall 1. The TV must be centered n the munt t avid leaning. 2. The munt is designed t attach t standard 2 x 4 r larger wall studs. If the wall isn t sturdy enugh then mre supprt will need t be added, cnsult an expert. 3. The munt must be securely fastened t a structure that can supprt 4 times the ttal weight f the televisin and munt. Dynamic Munting assumes n respnsibility fr damage frm an imprperly installed munt. 4. The munting hles need t be in the center f the studs, use a stud finder as needed lag screws are needed in the tp slts f the munt and 2 in the bttm slts lag screws need t be n each side f the center f the munt and the center f gravity f the televisin. 7. Yu can duble check these cnditins are meant by; Using the munt as a template, r Dwnlading and printing the Wall Munt Template ff f the website, r The cardbard bx the munt ships in has an utline f the bracket that attaches t the wall, cut ut t use. Install Vide at 4

5 Imprtant: The TV needs t be centered n the munt t avid leaning Figure 6, Psitining Munt n the Wall Munting T Wall 1. The televisin shuld be centered n the munt, if nt the televisin will sag t ne side. The heavier the TV and the mre ff center, the mre unlevel the TV will be thrugh its range f mtin. If yur stud placement desn t allw fr the TV t be centered, the Extra Wall Supprt (sld separately) will give mre side t side adjustment. 2. Mark the lcatins f the munting hles by; Using the munt as a template, r Dwnlading and printing the Wall Munt Template ff f the website, r The cardbard bx the munt ships in has an utline f the bracket that attaches t the wall, cut ut t use. 3. Once yu knw yur lcatin, pre-drill 1 f the tp rw f munting hles 2.5in deep using the 1/4in drill bit. 4. Get smene t help hld the munt t the wall. 5. Figure 7 shws the crrect rder t put n the lag screw. 6. Use a 9/16in wrench t install the lag screw; d nt tighten all f the way dwn yet. 7. Level the munt as shwn in Figure Mark and drill the ther 3 hles 2.5in deep. 9. Install the lag screws and tighten until the munt is firmly pressed against the wall. D NOT ver tighten. Figure 7, Lag Blt and Washer Order Install Vide at 5

6 Attaching the Televisin t the Munt After the abve steps are finished yu are ready t put the televisin n the munt. 1. Adjust the cunterbalance t the apprximate frce t handle the weight f yur televisin. See the Adjusting the Cunterbalance sectin n page 8 fr mre details. If in dubt, errr t the cunterbalance supplying t much frce. Yu can easily adjust frce later. 2. We recmmend having smene help putting the TV n the munt. 3. Hk the TV Hangers (with the TV attached t them) ver the Hk Plate as shwn in Figure Befre psitining the televisin side t side r pulling the munt dwn, insert the 2 #10 x 7/8 inch lng machine screws with washer thrugh the Hk Plate and int the TV Hangers, finger-tighten t ensure the TV will nt fall ff. 5. Adjust the televisin s that it is centered n the munt. 6. Tighten the screws dwn with a screwdriver. 7. Adjust the cunterbalance s that the televisin can be mved arund as easily as pssible but still be able t stay in the desired bttm psitin. See the Adjusting the Cunterbalance sectin n page 8. Figure 8, Attaching the Televisin Warning! D Nt Let G f the TV Until the Mtin has stpped n its Own. Psitins Munt Will Stay At The Dwn and Out Munt has a range f psitins the munt will hld the TV at. The general range is shwn in Figure 9. The munt can always stay in the tp psitin. Frm the tp psitin dwn 12 inches the munt can be set t stay but the angle may nt be vertical and the TV will nt have a wide range f psitins t stay at. The Munt really isn t designed t hld the TV in this range. Frm 12 inches t all f the way dwn the munt can be set t stay in a wide range f psitins. Depending n the weight f yur TV the range will vary. Fr lighter TVs (60 lbs and under) the munt may stay in the entire bttm range. Fr Heavier TVs (80 lbs and ver) the munt may nly have a range f abut 8 inches. Mving the Televisin Up and Dwn If the cunterbalance is set up crrectly the TV shuld be able t be lifted all f the way up int the tp/lcked psitin with reasnable effrt. T unlck frm this psitin pull ut n the bttm f the televisin. T get the televisin all the way t the bttm psitin yu may need t push dwn n the televisin. If the TV pps back up frm the desired bttm psitin, reduce the cunterbalance frce. Typically, the frce t lift the TV all f the way up is apprximately 20-30% f the weight f TV. Figure 9, Psitins Munt Will Stay At Install Vide at 6

7 Abve Shelf Munting T get the lwest pssible bttm psitin when munting abve a shelf, it is very imprtant that yu put extra thught int the munting prcess. The Munt can clear shelves up t 16 deep. The TV Clearance Table shws the minimum clearance [C] needed between the shelf tp and the bttm f the TV (r the bttm f an attached speaker, whichever is lwer) fr the munt t swing arund the shelf. T find the clearance needed, find the shelf depth [D], in this example 8, and g dwn the clumn and find the crrespnding minimum clearance height [C], which is 2.5. Figure 6 shws where t measure [C] and [H]. Figure 10 and the Munt Travel Table shws yu hw much dwnward travel yu will get with different shelf depths and heights abve the shelf. Fr example, t find the dwnward travel [T] when yu have an 8 shelf depth [D] and yu attach the bttm f the munt 6 abve the shelf [H]. First find the crrespnding [D] and lk dwn the clumn and find the clsest [H], which in this case is Nw g left alng the rw and find the crrespnding Travel [T]. In this case yu will get a dwnward travel f apprximately 26. Tips t get the Lwest Pssible Bttm Psitin Get the tp f the munt and the tp f the TV t be as clse as pssible. Typically yu ll get the lwest bttm psitin by being near the minimum clearance shwn in the TV Clearance Table. Getting the mst travel pssible ut f the munt, desn t mean yu ll get the lwest pssible bttm psitin. Fr example, fr an 8 shelf, t g frm 28 f travel, t 30 f travel, yu have t raise the munt up 6.5. S yur new bttm psitin is actually 4.5 higher. Figure 10, Shelf Clearance Drawing Install Vide at 7

8 Adjusting the Cunterbalance The Munt cmes ut f the bx set arund the 65 LB TV setting and will need t be adjusted fr the munt t wrk prperly with yur televisin. T adjust the cunterbalance, turn the bttm f the cunterbalance screw with a 9/16 inch bx r ratcheting wrench, see Figure 12. This mves the Cunterbalance Blck up and dwn. The apprximate cunterbalance blck settings fr varius televisin weights are shwn in Figure 11. In Figure 11 the cunterbalance is apprximately set fr a 65 Pund Televisin. T be able t mve the munt withut a TV n it, yu need t mve the Cunterbalance Blck t the Minimum Cunterbalance Frce. At this setting it will still take 15 t 20 punds f effrt t mve the munt which is harder than yu think. Yu shuld secure it t smething t get the munt t mve. Once yu put a TV n the munt, everything will wrk much better. Figure 11, Cunterbalance Settings Detail frm Figure 6 Figure 12, Adjusting Cunterbalance Bump Stp T help prevent the munt frm ver traveling, there is an adjustable Bump Stp n the munt. The Bump Stp is nt made t hld any lad, the cunterbalance shuld be set t hld the lad when in cntact with the Bump Stp. T test this just lift the TV up a little abve the Bump Stp and make sure the munt stays in psitin. T Tighten and lsen, hld the Screw with a Screwdriver still, and use a 7/16 Wrench t turn the nut. When turning the nut, clckwise is t tighten. Adjust bth f the Bump Stps n each side fr best perfrmance. Figure 13, Bump Stp Install Vide at 8

9 Setting the Tilt in the Tp Psitin In the tp psitin the munt tilts frm vertical t abut 7 degrees (Figure 2 and Figure 3). T set the angle, put the munt in the ut psitin fr easier access and s there isn t any frce n the cam. Adjust the Tp Tilt Cam by remving the tp Tilt Adjustment Blt (Figure 14) and putting it int a different set f hles and hand tighten with ne nut. Apprximate tilt settings are shwn in Figure 15. There is a cam n bth sides f the munt, use the Tp Tilt Alignment Marks and hles t ensure they are at the same psitin. Mve the munt up and see if the tilt is crrect, if nt change the psitin f the cams, it will prbably take a few times t get the tilt perfect. If yu get a lt f resistance when trying t push the munt t the Tp psitin, the Cam is set fr t much up tilt and yu will need t lessen it. Once yu have the desired psitin, tighten bth nuts with a 7/16 bx wrench and Philips screwdriver. Setting the Tilt in the Bttm and Out Psitins In the bttm and ut psitin the munts tilt can be set Vertical +/-1 degree. T adjust, lsen up the 2 Bttm Tilt Lck Nuts with a 7/16 bx wrench. Next mve the 2 Bttm Tilt Adjustment Blts in and ut with the 7/16 bx wrench until the munt is at the desired tilt, lck dwn the lcknuts when satisfied with the tilt. Figure 14, Tilt Adjust Hardware Figure 15, Tp Tilt Cam Settings Rubber Bumpers T help avid damage t the shelf, attach the Adhesive Rubber Bumpers t the bttm f the TV munt where it wuld cme in cntact. Paintable Plastic Cvers The Paintable Plastic Cvers can be painted t match yur wall r left as is t help the munt blend in. They simply hk ver the munting plate as shwn in Figure 17. Outlets can be installed under the cvers and then the wires ran under them. Yu may need lw prfile wires r an indented utlet t get it t fit thugh. Install Vide at 9

10 Wire Management Wires can be ruted thrugh the wire ruting hles and/r zip tied with the included zip ties as shwn in Figure 17. Ensure enugh slack remains s the wires can mve freely. Check that nthing is getting pinched r rubbing excessively after running wires. Figure 16, Wire Ruting Figure 17, Ideal Outlet Placement and Plastic Cver Maintenance T ensure the munt will wrk great fr as lng as pssible fllw these simple prcedures; 1. Mve the munt up and dwn at least twice a week, this keeps the seals in the gas springs iled. 2. Lubricate all jints every 3 mnths. May need mre, especially if utside 3. Visually check all blts every 3 mnths t ensure nthing lks like it is cming lse. Warranty Dynamic Munting guarantees the Dwn and Out Munt t be free f defects fr the prduct s warranty perid f 5 years. The warranty perid begins n the riginal date f shipping. The limited warranty is intended nly fr the riginal purchaser. The warranty will be vid if the munt is mdified in anyway r nt installed crrectly, Including verlading, abuse, r use fr any purpse ther than specified in these directins. This munt is fr indr use nly and the warranty will be vided if the munt is used utdrs. Dynamic Munting is nt liable fr any damage r injury caused frm the use f r the inability t use ur munt. T the maximum extent permitted by applicable law, Dynamic Munting disclaims any respnsibility fr incidental r cnsequential damages. Dynamic Munting LLC, U.S. PATENT NO , , Install Vide at 10