IMPORTANT SAFETY INFORMATION

Size: px

Start display at page:

Download "IMPORTANT SAFETY INFORMATION"

Adele Hill
5 years ago
Views:

1 Installatin Instructin English UNPACKING INSTRUCTIONS! Carefully pen the cartn, remve cntents and lay ut n cardbard r ther prtective surface t avid damage.! Check package cntents against the Supplied Parts List in the next page t assure that all cmpnents were received undamaged. D nt use damaged r defective parts.! Carefully read all instructins befre attempting installatin. IMPORTANT SAFETY INFORMATION! Install and perate this device with care. Please read this instructin befre installatin, and carefully fllw all instructins cntained herein. Use prper safety equipment during installatin.! Please call a qualified installatin cntractr fr help if yu dn't understand these directins r have any dubts abut the safety f the installatin. D nt use this prduct fr any purpse r in any cnfiguratin nt explicitly specified in this instructin. We hereby disclaims any and all liability fr injury r damage arising frm incrrect assembly, incrrect munting, r incrrect use f this prduct. 1

2 Supplied Par ts List (1) Ple-a (1) C Clamp-b (1) C Clamp Brace-c (1) Swivel Arm-d (2) VESA Plate-e (3) M5x16 Blt-f (2) M8x12 Blt-g (2) Nut-h (1)M10 Blt-i (1)Supprt Plate-j (1)M10 Washer-k (1)Spring Washer-l (1) Grmmet Base Plate-m (1)Wire Clip-n1 (4)Wire Clip-n2 (1)Allen Key- (1)Wrench-p (8)M4x12 Blt-q (8)M4x30 Blt-r (8)M4 Spacer-s Tls Required Phillips Screwdriver 2 CAUTION!! This mnitr desktp munt must be securely attached t the hrizntal desk. If the munt is nt prperly installed it may fall, resulting in WARNING pssible injury and/r damage.

3 Step 1 Install the Ple t the Desktp Optin A: Desk Clamp Install a 1. Install the C -Clamp Brace(c) t the Ple (a) using 3pcs M5x16 Blts(f), see Figure Install the C -Clamp(b) t the ple assembly accrding t the thickness f the desktp. The thickness can be changed t three psitins. Cnnect it using 2pcs M8x12 Blts(g), and tighten using the Allen Key(). Tighten the C -Clamp t the desktp using the plastic knb, see Figure 2. f Figure 1 c Figure 2 b Plastic Knb g Optin B: Grmmet Base Install Existing Grmmet Hle Installatin If the existing grmmet hle cmes with a plastic prtectr, remve it t ensure a flat surface befre installing the desk munt. 1. Install the Grmmet Base Plate(m) t the Ple(a) using 3pcs M5x16 Blts(f), see Figure 3. a m f Figure 3 2. Psitin the Ple(a) n the munting surface and secure using the Supprt Plate (j), M10 Washer(k), Spring Washer(l) and M10 Blt(i). Fasten the M10 Blt using prvided Wrench(p), see Figure 4. Figure 4 l i k j 3

4 Step 1 Install the Ple t the Desktp Optin B: Grmmet Base Install Self Drilled Grmmet Hle Installatin 1. Psitin the Ple(a) n the munting surface and mark the center hle. Drill a 3/8" (10mm) diameter hle at the marked psitin thrugh the munting surface. 2. Install the Grmmet Base Plate(m) t the Ple(a) using 3pcs M5x16 Blts(f), see Figure 5. f Figure 5 a m 3. Psitin the Ple(a) n the munting surface and secure using the Supprt Plate (j), M10 Washer(k), Spring Washer(l) and M10 Blt(i). Fasten the M10 Blt using prvided Wrench(p), see Figure 6. Figure 6 l i k j Step 2 Install Arm t the Ple Install Swivel Arm(d) t the Ple(a). Fasten the blt with supplied Allen Key(). Attach the Wire Clip(n1,n2) t the Ple(a) and Swivel Arm(d). d n2 n1 4

5 Step 3 Attach the VESA Plate t the Mnitr q s r Fr Mnitr with Flat Back Fr Mnitr with Curved r Recessed Back Step 4 Slide the Mnitr nt the Head f Swivel Arm h Slide the mnitr nt the head f Swivel Arm(d) as shwn in the abve diagram. Install the security Nut(h). Make sure the security nut is installed befre yu rtate the mnitr. 5

6 Step 5 Fix the Tilt Angle and Adjust the Level f Mnitr Fix the tilt angle Tighten the blt with the supplied Allen Key() t fix the tilt angle. Ignre this step if mnitrs are level If ne mnitr is lwer, remve the Nut(h) and turn the blt cunter-clckwise with supplied Allen key() t raise the mnitr. Install the Nut(h) after the adjustment. Step 6 Make the Necessary Adjustments and Manage the Wires n1 Use the supplied Allen Key() t make the necessary adjustments. Manage the wires and stre the Allen keys() in Wire Clip(n1) fr future use. Thank yu fr chsing ur prducts! 6

Dual Monitor Desk Mount

Dual Monitor Desk Mount Dul Mnitr Desk Munt Instructin Mnul SKU: STAND-V002 Scn the QR cde with yur mbile device r llw the link r helpul vides nd speciictins relted t this prduct. https://viv-us.cm/prducts/stnd-v002 help@viv-us.cm