Wirsbo hepex Tubing, 5/16" to 2" Coils Submittal information Revision I: Sept. 18, 2018 Project information
|
|
|
- Florence Griffith
- 5 years ago
- Views:
Transcription
1 Wirsbo hepex Tubing, 5/16" to 2" Coils Revision I: Sept. 18, ProPEX is a registered trademark of ProPEX is a trademark of Crosslinked polyethylene PEX-a Engel method 0.22 BTU/h/ft/ F 200 F at 80 psi (93 C at 5.51 bar); 180 F at 100 psi (82 C at 6.89 bar) 73.4 F at 160 psi (23 C at bar) 1.1"/10 F per 100 ft. (27.94mm/5.56 C per 30.48m) Wirsbo hepex tubing is used for closed-loop heating and cooling applications, including radiant and hydronic distribution. It has an oxygen diffusion barrier that meets German DIN 4726/9. A polyethylene layer is extruded over the oxygen barrier to protect from site abuse and moisture saturation. Description Part number I.D. O.D. Weight 5/16" Wirsbo hepex, 100-ft. coil A " 0.430" 3.00 lbs. 5/16" Wirsbo hepex, 250-ft. coil A " 0.430" 7.49 lbs. 5/16" Wirsbo hepex, 1,000-ft. coil A " 0.430" lbs. ⅜" Wirsbo hepex, 100-ft. coil A " 0.500" 4.19 lbs. ⅜" Wirsbo hepex, 400-ft. coil A " 0.500" lbs. ⅜" Wirsbo hepex, 1,000-ft. coil A " 0.500" lbs. ½" Wirsbo hepex, 100-ft. coil A " 0.625" 5.30 lbs. ½" Wirsbo hepex, 300-ft. coil A " 0.625" lbs. ½" Wirsbo hepex, 500-ft. coil A " 0.625" lbs. ½" Wirsbo hepex, 1,000-ft. coil A " 0.625" lbs. ⅝" Wirsbo hepex, 100-ft. coil A " 0.750" 7.60 lbs. ⅝" Wirsbo hepex, 300-ft. coil A " 0.750" lbs. ⅝" Wirsbo hepex, 400-ft. coil A " 0.750" lbs. ⅝" Wirsbo hepex, 1,000-ft. coil A " 0.750" lbs. ¾" Wirsbo hepex, 100-ft. coil A " 0.875" lbs. ¾" Wirsbo hepex, 300-ft. coil A " 0.875" lbs. ¾" Wirsbo hepex, 500-ft. coil A " 0.875" lbs. ¾" Wirsbo hepex, 1,000-ft. coil A " 0.875" lbs. 1" Wirsbo hepex, 100-ft. coil A " 1.125" lbs. 1" Wirsbo hepex, 300-ft. coil A " 1.125" lbs. 1" Wirsbo hepex, 500-ft. coil A " 1.125" lbs. 1¼" Wirsbo hepex, 100-ft. coil A " 1.375" lbs. 1¼" Wirsbo hepex, 300-ft. coil A " 1.375" lbs. 1½" Wirsbo hepex, 100-ft. coil A " 1.625" lbs. 1½" Wirsbo hepex, 300-ft. coil A " 1.625" lbs. 2" Wirsbo hepex, 100-ft. coil A " 2.125" lbs. 2" Wirsbo hepex, 300-ft. coil A " 2.125" lbs. Approved fitting system is ProPEX. 1 Refer to the Uponor Complete Design Assistance Manual (CDAM) or Hydronic Piping Design Assistance Manual (HPDAM) for further information. ANSI/NSF 14; ANSI/NSF 61; ASTM F876; ASTM F877; ASTM F1960; ASTM F2023; ASTM E84; CAN/ULC S102.2; ASTM E119/UL 263; CAN/ULC S101; ASTM E814/ULC S115; CSA B137.5; CSA B214; DIN 4726/9; AWWA C th Street West
2 Wirsbo hepex Tubing, 2½" to 4" Coils Revision H: Sept. 18, 2018 Job Name: Crosslinked polyethylene PEX-a Engel Method 0.22 Btu.ft/sq.ft.hr.degF 200 F at 80 psi (93 C at 5.51 bar) 180 F at 100 psi (82 C at 6.89 bar) 73.4 F at 160 psi (23 C at bar) 1.1"/10 F per 100 ft. (27.94mm/5.56 C per 30.48m) Wirsbo hepex tubing is used for closed-loop heating and cooling applications, including radiant and hydronic distribution. It has an EVOH oxygen diffusion barrier that meets German DIN 4726/9. These larger-sized products are designed for commercial projects or other customdesigned applications. Description Part number Tube ID Tube OD Weight 2½" Wirsbo hepex, 100-ft. coil A " 2.625" lbs. 2½" Wirsbo hepex, 300-ft. coil A " 2.625" lbs. 3" Wirsbo hepex, 100-ft. coil A " 3.125" lbs. 3" Wirsbo hepex, 300-ft. coil A " 3.125" lbs. 3½" Wirsbo hepex, 100-ft. coil A " 3.625" lbs. 4" Wirsbo hepex, 100-ft. coil A " 4.125" lbs. Use ProPEX fittings to connect pipe sizes up to 3". 1 Use WIPEX fittings for 3½" and 4" pipe. Refer to the Uponor Complete Design Assistance Manual (CDAM) or Hydronic Piping Design Assistance Manual (HPDAM) for additional information. ANSI/NSF 14; ANSI/NSF 61; ASTM F876; ASTM F877; ASTM F1960; ASTM F2023; ASTM E84; CAN/ULC S102.2; ASTM E119/UL 263; CAN/ULC S101; ASTM E814/ULC S115; CSA B137.5; CSA B214; DIN 4726/9; AWWA C904 3 Uponor, Inc. 1 ProPEX is a registered trademark of Uponor, Inc. ProPEX is a trademark of
3 Wirsbo hepex Tubing, Straight Lengths Revision I: Sept. 18, 2018 Project Information Technical Data 1 ProPEX is a registered trademark of ProPEX is a trademark of Crosslinked polyethylene PEX-a Engel method 200 F (93 C) at 80 psi 180 F (82 C) at 100 psi 73.4 F (23 C) at 160 psi 1.1"/10 F/100' (27.94mm/5.56 C/30.48m) Wirsbo hepex tubing is used for closed-loop heating and cooling applications, including radiant and hydronic distribution. Wirsbo hepex tubing has an EVOH oxygen diffusion barrier that meets German DIN 4726/9. A polyethylene layer extruded over the EVOH barrier protects tubing from site abuse and moisture saturation. Description Part number A B ½" Wirsbo hepex, 20-ft. straight length, 500 ft. (25 per bundle) ⅝" Wirsbo hepex, 20-ft. straight length, 300 ft. (15 per bundle) ¾" Wirsbo hepex, 20-ft. straight length, 300 ft. (15 per bundle) 1" Wirsbo hepex, 20-ft. straight length, 200 ft. (10 per bundle) 1¼" Wirsbo hepex, 20-ft. straight length, 100 ft. (5 per bundle) 1½" Wirsbo hepex, 20-ft. straight length, 100 ft. (5 per bundle) 2" Wirsbo hepex, 20-ft. straight length, 100 ft. (5 per bundle) 2½" Wirsbo hepex, 10-ft. straight length, 30 ft. (3 per bundle) 2½" Wirsbo hepex, 20-ft. straight length, 60 ft. (3 per bundle) 3" Wirsbo hepex, 10-ft. straight length, 30 ft. (3 per bundle) 3" Wirsbo hepex, 20-ft. straight length, 40 ft. (2 per bundle) 3½" Wirsbo hepex, 10-ft. straight length, 30 ft. (3 per bundle) 3½" Wirsbo hepex, 20-ft. straight length, 40 ft. (2 per bundle) 4" Wirsbo hepex, 10-ft. straight length, 20 ft. (2 per bundle) 4" Wirsbo hepex, 20-ft. straight length, 10 ft. (1 per bundle) A A A A A A A A A A A A A A A " 0.574" 0.671" 0.862" 1.054" 1.244" 1.629" 2.011" 2.011" 2.400" 2.400" 2.784" 2.784" 3.209" 3.209" 0.625" 0.750" 0.875" 1.125" 1.375" 1.625" 2.125" 2.625" 2.625" 3.125" 3.125" 3.625" 3.625" 4.125" 4.125" Bundle weight lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs. Use ProPEX fittings for pipe sizes to 3". 1 Use WIPEX fittings for 3½" and 4" pipe. Refer to the Uponor Complete Design Assistance Manual (CDAM) or the Uponor Hydronic Piping Design Assistance Manual (HPDAM) for additional information. ANSI/NSF 14; ANSI/NSF 61; ASTM F876; ASTM F877; ASTM F1960; ASTM F2023; ASTM E84; CAN/ULC S102.2; ASTM E119/UL 263; CAN/ULC S101; ASTM E814/ULC S115; CSA B137.5; CSA B214; DIN 4726/9; AWWA C904 3
4 Pre-insulated Wirsbo hepex (ASHRAE ) Revision B: Sept. 19, 2018 Service pipe: Insulation: Operating condition limits: (hydrostatic ratings) Crosslinked polyethylene PEX-a Engel method pipe Polyethylene foam 0.25 Btu.in/h/sq.ft/ F 200 F at 80 psi (93 C at 5.5 bar) 180 F at 100 psi (82 C at 6.9 bar) 73.4 F at 160 psi (23 C at 11 bar) 1.1"/10 F per 100' (27.94mm/5.56 C per 30.48m) Pre-insulated Wirsbo hepex features oxygen-barrier PEX pipe encased in polyethylenefoam insulation to meet ASHRAE energy-code requirements for hydronic heating and cooling or radiant heating and cooling applications. The piping is approved for direct burial in soil, provided it is not exposed to groundwater. Uponor recommends adding ½" of insulation to accommodate for foam compression in direct-burial applications. Description Part no. O.D. Heat loss (at 70 T) R-Value Coil size (O.D. x Width) Weight (lb./coil) ½" Pre-insulated Wirsbo hepex with ½" insulation, 100-ft. coil A " 7.4 Btu/hr/ft " x 6.5" 8.0 lbs. ¾" Pre-insulated Wirsbo hepex with ½" insulation, 100-ft. coil A " 9.0 Btu/hr/ft " x 6.5" 12.8 lbs. 1" Pre-insulated Wirsbo hepex with ½" insulation, 100-ft. coil A " 10.6 Btu/hr/ft " x 9" 21.0 lbs. 1¼" Pre-insulated Wirsbo hepex with ½" insulation, 100-ft. coil A " 12.1 Btu/hr/ft " x 9" 30.0 lbs. 1½" Pre-insulated Wirsbo hepex with ½" insulation, 100-ft. coil A " 13.6 Btu/hr/ft " x 9" 42.0 lbs. 2" Pre-insulated Wirsbo hepex with ½" insulation, 100-ft. coil A " 16.5 Btu/hr/ft " x 13.5" 65.0 lbs. ½" Pre-insulated Wirsbo hepex with 1" insulation, 100-ft. coil A " 6.3 Btu/hr/ft " x 9" 11.0 lbs. ¾" Pre-insulated Wirsbo hepex with 1" insulation, 100-ft. coil A " 7.1 Btu/hr/ft " x 13.5" 22.0 lbs. 1" Pre-insulated Wirsbo hepex with 1" insulation, 100-ft. coil A " 8.8 Btu/hr/ft " x 13.5" 30.2 lbs. 1¼" Pre-insulated Wirsbo hepex with 1" insulation, 100-ft. coil A " 10.0 Btu/hr/ft " x 9" 39.2 lbs. 1½" Pre-insulated Wirsbo hepex with 1½" insulation, 75-ft. coil A " 7.0 Btu/hr/ft " x 13.5" 49.5 lbs. 2" Pre-insulated Wirsbo hepex with 1½" insulation, 75-ft. coil A " 8.6 Btu/hr/ft lbs. ½" Pre-insulated Wirsbo hepex with 1½" insulation, 100-ft. coil A " 4.0 Btu/hr/ft " x 9" 22.0 lbs. ¾" Pre-insulated Wirsbo hepex with 1½" insulation, 100-ft. coil A " 4.9 Btu/hr/ft lbs. 1" Pre-insulated Wirsbo hepex with 1½" insulation, 100-ft. coil A " 5.7 Btu/hr/ft " x 13.5" 37.5 lbs. 1¼" Pre-insulated Wirsbo hepex with 1½" insulation, 100-ft. coil A " 6.4 Btu/hr/ft lbs. 1½" Pre-insulated Wirsbo hepex with 2" insulation, 50-ft. coil A " 5.2 Btu/hr/ft lbs. 2" Pre-insulated Wirsbo hepex with 2" insulation, 50-ft. coil A " 6.4 Btu/hr/ft " x 13.5" 81.3 lbs. Use ProPEX 1 fittings to connect the piping. Refer to the ProPEX Connections Instructional Guide or the Uponor Radiant Floor Heating Handbook for additional information. CSA B137.5; ASTM F876; ASTM F877; ASTM F1960; ASTM F2023; DIN 4726/9; NSF/ANSI 14; NSF/ANSI 61 HUD; ICC; IMC; UMC; IPC; UPC; NSPC; IRC; NBC of Canada; NPC of Canada; UFGS Listings CCMC; cnsfus-rfh; cnsfus-pw; CSA; IAPMO; ICC-ES; ITS; PPI TR-4; UL Hydronic heating and cooling systems th Street West Mississauga, ON L5N 1W1 CANADA 1 ProPEX is a registered trademark of ProPEX is a trademark of
5 ProPEX Ring Revision I: Nov. 1, 2018 Engel-method crosslinked polyethylene (PEX-a) Density: 926 to 940 kg/m 3 Degree of crosslinking: 70% to 89% Uponor ProPEX rings are required to make a proper ProPEX connection. 1 The ProPEX ring with stop includes a leading edge chamfer and stop edge. Description Part number Length I.D. O.D. Weight ProPEX Ring, ⅜" ProPEX Ring with Stop, ½" ProPEX Ring with Stop, ⅝" ProPEX Ring with Stop, ¾" ProPEX Ring with Stop, 1" ProPEX Ring with Stop, 1¼" ProPEX Ring with Stop, 1½" ProPEX Ring with Stop, 2" ProPEX Ring with Stop, 2½" ProPEX Ring with Stop, 3" Q Q Q Q Q Q Q Q Q Q " 0.63" 0.79" 0.87" 1.10" 1.35" 1.61" 1.97" 2.61" 3.12" 0.49" 0.63" 0.75" 0.88" 1.13" 1.38" 1.63" 2.14" 2.66" 3.16" 0.74" 0.87" 1.00" 1.13" 1.42" 1.66" 1.91" 2.61" 3.25" 3.87" lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs. Square cut the Uponor PEX tubing. Remove excess material. Slide the ProPEX ring over the end of the tubing (maximum 1 /16" over-hang for rings without stop). When using the ProPEX ring with stop, slide the ring on the tubing with the chamfered edge first until the end of the tubing contacts the stop edge. Expand the tubing and ring. If using the ProPEX Manual Expander Tool, rotate the tool a quarter turn after each expansion to prevent the formation of grooves. Remove the expansion tool and fully seat the tubing and ring against the shoulder of the fitting. Make ProPEX connections at temperatures above 5 F/-15 C. For more information, refer to the Uponor ProPEX Connections Instructional Guide. cnsfus-fs 3 ; cnsfus-pw; cnsfus-rfh; cqaius; UL; CSA; PPI TR-4; ICC-ES; IAPMO; BMEC; CCMC; cqaius P321 ICC; IPC; IMC; IRC; UPC; UMC; NSPC; HUD; UFGS; NPC of Canada; NBC of Canada ANSI/NSF 14; ANSI/NSF 61; ASTM F876; ASTM F877; ASTM F1960; ASTM F2023; ASTM E84; CAN/ULC S102.2; ASTM E119/UL 263; CAN/ULC S101; ASTM E814/ULC S115; CSA B137.5; CSA B214; UL ; ULC/ORD-C199P 3 PEX-a plumbing systems AquaSAFE fire safety systems Hydronic radiant heating and cooling systems Snow melting systems Permafrost prevention systems 1 ProPEX is a registered trademark of Uponor, Inc. ProPEX is a trademark of 2 Visit listing agency s website for complete information; 3 For ½", ¾", 1", 1¼", 1½" and 2" tubing only
Ecoflex pre-insulated pipe energy efficiency made easy
E c o f l e x C o m p l e t e Catalog Supplement June 2010 Hydronic heating, cooling and potable-water distribution Fast, easy installations Energy-efficient Flexible, durable Custom-cut, long lengths
Effective Date: April 2018 Void After: April 2019
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the
Wirsbo / AquaPEX. AquaPEX Tube. White Coils. White Straight Lengths. Wirsbo AquaPEX plus Tubing. Red Coils. Blue Coils PAGE 055-1
2011 Wirsbo / AquaPEX PAGE 055-1 Code# Description Pkg Mfg# AquaPEX Tubing AquaPEX Tube Wirsbo AquaPEX tubing is used in hot and cold potable water distribution systems and Uponor residential fire safety
Product Catalogue. February We mean progress. PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping
Product Catalogue February 2019 PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping We mean progress. Table of contents Table of contents 1 Uponor Design Services
Product Catalogue. July We mean progress. PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping
Product Catalogue July 2018 PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping We mean progress. Table of contents Table of contents 1 Uponor Design Services and
APRIL Flawlessly moving water to provide the ultimate in comfort, safety and convenience for residential and commercial applications.
Product Catalogue APRIL 2010 Radiant Heating and Cooling Systems Pre-insulated Pipe Systems Fire Sprinkler Systems Plumbing Systems Flawlessly moving water to provide the ultimate in comfort, safety and
PLUMBING, FIRE SAFETY, AND RADIANT HEATING AND COOLING SYSTEMS INSTRUCTIONAL GUIDE. Making ProPEX Connections
PLUMBING, FIRE SAFETY, AND RADIANT HEATING AND COOLING SYSTEMS INSTRUCTIONAL GUIDE Making ProPEX Connections Table of Contents Making ProPEX Connections....................... General ProPEX Connection
Product Catalogue. July PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping
Product Catalogue July 2016 PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping Table of contents Uponor begins with you 3 Optimized for mobile 5 Uponor Design Services
Radiant heating and cooling Pre-insulated piping
Product Catalog July 2017 PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping Table of contents Upgrade to Uponor 3 Uponor Design Services and Technical Support...6
PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping
Product Catalog February 2017 PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping See inside for our newly reduced prices on PEX-a pipe supports, brass valves and
PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping
Product Catalog July 2016 PEX plumbing Fire safety Hydronic piping Radiant heating and cooling Pre-insulated piping Table of contents Uponor begins with you 3 Optimized for mobile 5 Uponor Design Services
EVALUATION SUBJECT: DIVISION: HEATING, VENTILATING AND AIR CONDITIONING (HVAC) SECTION: HVAC DUCTS AND CASINGS.
ICC-ES Report PMG-1171 Reissued 11/2018 This report is subject to renewal 11/2019 EVALUATION SUBJECT: UNDERGROUND SINGLE WALL & DOUBLE WALL INSULATED DUCT FOR HVAC DIRECT BURIAL APPLICATIONS AND UNDERGROUND
MATERIALS FOR PLUMBING SYSTEMS FITTING AND INSTALLATION GUIDE
MATERIALS FOR PLUMBING SYSTEMS FITTING AND INSTALLATION GUIDE THINK GLOBALLY, ACT LOCALLY CONTENTS Propex DZR fittings and pex 2 Why depend on Propex hot and cold piping system 3 Cross linked polyethylene
ob or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Installed Date: 1 1/2" 4" 1/8 Bend PVDF 1 1/2" 4" Caps PVDF
Submittal Data Sheet ob or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Date Date Date Installed Date: < STANDARDS > ASTM F1673 ASTM D3222 ASTM E84 B 181.3 CAN/ULC-S102.2
CONNECTION SYSTEM Includes Push-Fit and Barb Products and PEX Tubing
1 1-877-700-4242 1-877-700-4242 The CONNECTION SYSTEM Includes Push-Fit and Barb Products and PEX Tubing Contents Introduction 2-3 Push-Fit Fittings 4-6 Stops and Fixture Supply Fittings 7 Push-Fitting
EVALUATION SUBJECT: PUSH FIT FITTINGS DIVISION: PLUMBING SECTION: DOMESTIC WATER PIPING. Report Holder:
ICC-ES Report PMG-1149 Reissued 08/2017 This report is subject to renewal 08/2018 EVALUATION SUBJECT: PUSH FIT FITTINGS DIVISION: 22 00 00 PLUMBING SECTION: 22 11 16 DOMESTIC WATER PIPING Report Holder:
SHARKBITE. PEX Plumbing a Better Home
SHARKBITE PEX Plumbing a Better Home Benefits of SharkBite PEX PROUDLY AMERICAN MADE Health/Safety No glue, solder, or solvents required for the connection process, which keeps potentially dangerous chemicals
Product Catalog. Flawlessly moving water to provide the ultimate in comfort, safety and convenience for residential and commercial applications.
Product Catalog APRIL 2009 Radiant Heating and Cooling Systems Plumbing Systems Fire Safety Systems Pre-insulated Pipe Systems Flawlessly moving water to provide the ultimate in comfort, safety and convenience
Equivalent Length of Fittings
Equivalent Length of Fittings This section provides the equivalent length of piping pressure loss for several ProPEX fittings. The equivalent length is used to approximate the impact the fittings have
INSULPEX PRE-INSULATED PEXa PIPING DESIGN GUIDE. Construction Automotive Industry.
INSULPEX PRE-INSULATED PEXa PIPING DESIGN GUIDE www.rehau.com Construction Automotive Industry TABLE OF CONTENTS 1......Scope...3 2......Design Considerations...4 3......System Overview...5 3.1...System
AQUIFER DISTRIBUTION LTD. SASKATOON PH (306) FAX (306) REGINA PH (306) FAX (306) UPONOR AQUAPEX PIPE
UPONOR AQUAPEX PIPE Sec 15-32 F1040500 449 0104 0500 1/2" X 100' WHITE AQUAPEX PIPE 0.68 F1040750 449 0104 0750 3/4" X 100' WHITE AQUAPEX PIPE 1.32 F1041000 449 0104 1000 1" X 100' WHITE AQUAPEX PIPE 2.32
Long Term Strength And It s Consequences for PEX
Figure 1 Figure 1 is a chart displaying Long Term strength of a polymer pipe. To find these curves you start a large number of pressure tests at different stress (inside pressure) levels. And you wait
PE 2708 CTS & IPS GAS PIPE
Specifications: Resin Chevron Phillips TR418Q PE 2708 Resin formulation listed in PPI TR4 Hydrostatic Design Basis: 1250 psi @ 73 F, 800 psi @ 140 F Cell Classification per ASTM D3350 = 234373E or 234375E
IAPMO GUIDE CRITERIA FOR BALL VALVES IAPMO IGC PURPOSE
INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS IAPMO GUIDE CRITERIA FOR BALL VALVES IAPMO IGC 157-20067 1 PURPOSE 1.1 The purpose of this standard is to establish an acceptable standard
IAPMO IS PUBLIC REVIEW DRAFT Thrust Blocking for Rubber Gasketed and Solvent Cement Joints
IAPMO IS 33-2019 PUBLIC REVIEW DRAFT Thrust Blocking for Rubber Gasketed and Solvent Cement Joints IAPMO Standard IAPMO IS 33 2019 Published: Month Year Published by International Association of Plumbing
Safety. April 2018 Supersedes all previous publications 2018 Chevron Phillips Chemical Company LP
Technical Note 802 Leak Testing of Polyethylene Pipe For Municipal and Industrial Applications Part 1 Pre-Test Considerations Leak testing may be used to find leaks in a newly constructed or newly modified
PRESSURE DROP CHARTS
PRESSURE DROP FOR SMALL PEX TUBING AT 100 F Take the total heat load (BTUH) for the area that the loop is covering and divide it by 501. Divide the result with the Delta-T to find GPM for the loop. Find
For use in Natural Gas & Liquefied Petroleum Gas Applications
GasShield For use in Natural Gas & Liquefied Petroleum Gas Applications Streamline GasShield Coated Copper Tube comes coated with a yellow layer of seamless polyethylene. Commonly used with the distribution
1 Exam Prep. Questions and Answers
Part 1 1 Exam Prep Standard for Polyvinyl Chloride Pressure Pipe ANSI/AWWA C900-07 Questions and Answers 1. Which of the following statement is not a correct statement? A. A DR is the average O.D. divided
Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Installed Date:
Submittal Data Sheet Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Date Date Date Installed Date: introduction < STANDARDS > ASTM F1412 ASTM D 4101 ASTM D 635
SOLUTION ASTM F1960. Sioux Chief Tubing. Mr. PEX Tubing. Sioux Chief PowerPEX. Wolverine Brass WOLV-XPEX. Milwaukee Expansion Tools
ASTM SOLUTION Sioux Chief Tubing Mr. PEX Tubing Sioux Chief PowerPEX Wolverine Brass WOLV-XPEX Milwaukee Expansion Tools Phone: 1-800-523-5130 Fax: 1-800-338-1867 www.plumbmaster.com Phone: 1-800-944-9292
This loop is filled with an antifreeze solution such
Solar Panel expansion Tank Sizing: Getting It right Part I The most common type of solar thermal system uses a closed piping loop between the collector array and storage tank heat exchanger. BY JOhN SIeGeNThAler
INSERT FITTINGS INSERT FITTINGS
Insert Tee Insert x Female Tee Insert Elbow Insert x Male Elbow Insert Coupling Insert x Male Adapter Insert x Female Adapter Insert Plug POLY and NYLON FITTINGS For use with Poly Tubing Fitting 1/2 3/4
Balancing Valves. Applications/ Features: Ordering Information: Accessories:
Applications/ Features: Danfoss MSV balancing valves are designed to provide terminal or circuit flow balance in hydronic heating or cooling systems. Each valve provides a high level of balancing accuracy
Product Information Bulletin
Product Information Bulletin BULLETIN NO. ISSUED: REPLACES: 207 July 18, 2011 December 31, 2007 NBC 2005 and 2010, Part 9 - Prescriptive Requirements for ICF Construction Page 2 of 5 The National Building
TZ WEDGE ANCHOR FOR CRACKED AND UNCRACKED CONCRETE
www.ucanfast.com TECHNICAL MANUAL SECTION 2.2 PAGE 1 / 10 ä DESCRIPTION UCAN TZ torque controlled mechanical expansion wedge anchors have a Category 1 classification. They are used to resist static, wind
SECTION BUTTERFLY VALVES
SECTION 15112 BUTTERFLY VALVES PART 1 GENERAL 1.01 SUMMARY A. All butterfly valves shall be of the tight closing, rubber seated type and fully comply with the latest revision of AWWA Standard C504, Class
Operating Procedures for GripTight 15.5 SDR & IPS Test Plugs
EST Group DC2518 08/01 REV 3 12/12 Page 1 of 6 Operating Procedures for GripTight SDR & IPS Test Plugs WARNING For proper operation, GripTight plugs must be assembled as shown in Figure 1. Pressure testing
Horizontal Bladder Tanks
DATA SHEET Horizontal Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
Submittal Package. Viega MegaPress Fitting System. Chilled Water. Hydronic Heating. Fire Protection. Low Pressure Steam. Compressed Air (no oil)
Viega MegaPress Fitting System Chilled Water Hydronic Heating Fire Protection Low Pressure Steam Compressed Air (no oil) Industrial Gases Vacuum 1 of 11 Viega MegaPress Fitting System Viega MegaPress is
EVALUATION SUBJECT: SPUNSTRAND STANDARD AND INSULATED UNDERSLAB DUCTS
ICC-ES Report ESR-1681 Reissued 12/2017 This report is subject to renewal 12/2018 EVALUATION SUBJECT: SPUNSTRAND STANDARD AND INSULATED UNDERSLAB DUCTS DIVISION: 23 00 00 HEATING, VENTILATING AND AIR CONDITIONING
Presented to the IAPMO Standards Review Committee on March 7, 2016
Summary of Substantive Changes between the 2015 edition of ASSE 1070/ASME A112.1070/CSA B125.70, Water Temperature Limiting Devices, the 2004 edition of ASSE 1070, Water Temperature Limiting Devices, and
PVC FASTTAP SADDLES for IPS Mains. Main Size OUTLET 1 FPT 3/4 CTS (7/8 OD) COMPRESSION 1 CTS (1 1/8 OD) COMPRESSION 3/4 IPS COMPRESSION
PVC FASTTAP SADDLES PVC FASTTAP SADDLES for IPS Mains THE ULTIMATE CONNECTION OUTLET 3/4 IPS FEMALE SLIP OR 1 IPS MALE SLIP SOLVENT WELD 1 IPS FEMALE SLIP SOLVENT WELD 3/4 MPT 1 MPT 3/4 FPT MAIN 13/16
Consult with manufacturers concerning permeation of the pipe walls, jointing materials, valve seats, etc.
Design Manual Chapter 4 - Water Mains 4C - Facility Design 4C-1 Facility Design A. General Water mains and appurtenances, including hydrants and valves, should be provided along all streets including connections
Geotech Portable Bladder Pumps Installation and Operation Manual
Geotech Portable Bladder Pumps Installation and Operation Manual Rev. 1 09/22/04 Part # 11150272 Table of Contents System Description... p. 02 Function and Theory...p. 02 System Components... p. 02 System
Model MTB-ASME Vertical Bladder Tanks
DATA SHEET Model MTB-ASME Vertical Bladder Tanks Features n UL Listed for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
Model MTB-ASME Horizontal Bladder Tanks
DATA SHEET Model MTB-ASME Horizontal Bladder Tanks Features n UL Listed and FM Approved for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure
Model MTB-ASME Vertical Bladder Tanks
DATA SHEET Model MTB-ASME Vertical Bladder Tanks Features n UL Listed for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
EVALUATION SUBJECT: PUSH FIT FITTINGS DIVISION: PLUMBING SECTION: DOMESTIC WATER PIPING. Report Holder:
ICC-ES Report PMG-1256 Reissued 10/2017 This report is subject to renewal 06/2018 EVALUATION SUBJECT: PUSH FIT FITTINGS DIVISION: 22 00 00 PLUMBING SECTION: 22 11 16 DOMESTIC WATER PIPING Report Holder:
Casing Spacer Technology Leaders
Casing Spacer Technology Leaders Benefit today. Save down the line. www.racispacers.com NORTH AMERICA Why Raci Raci has been the global leader in casing spacer technology since 1952. Our uniquely designed,
Water Hammer Arrestors
Water Hammer rrestors watts.com What is Water Hammer? T he noise from banging pipes is caused by shocks of high speed water flowing in the piping system when a fixture is suddenly closed. Sudden stoppage
EVALUATION SUBJECT: CAST IRON SOIL PIPE AND FITTINGS DIVISION: PLUMBING SECTION: SANITARY WASTE AND VENT PIPING.
ICC-ES Report PMG-1407 Reissued 10/2017 This report is subject to renewal 10/2018 EVALUATION SUBJECT: CAST IRON SOIL PIPE AND FITTINGS DIVISION: 22 00 00 PLUMBING SECTION: 22 13 16 SANITARY WASTE AND VENT
Volume I: Pressure Piping Systems Design
Volume I: Pressure Piping Systems Design Municipal Technical Manual Series MUNICIPAL PRESSURE PIPING SYSTEMS Blue Brute Piping Systems Bionax Piping Systems IPEX Centurion Piping Systems IPEX Fusible TM
NEW PRODUCT Effective Date: April 15th, 2015
Full Freight Allowed: Order any quantity of the new valves or fittings on this sheet and receive FFA on the first order! Any Legend item may be added to the order. Full Freight Allowance applicable on
Vertical Bladder Tanks
DATA SHEET Vertical Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
Ford Service Saddles and Tapping Sleeves
Section AA 5/2001 Ford Service Saddles and Tapping Sleeves The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 219/563-3171 FAX: 1-800-826-3487
The Duopex Gas. to make every job quick and easy. it provides a revolutionary alternative for the professional plumber and 02_DUOPEX GAS GAS MANUAL
duopex gas manual The Duopex Gas pipe and fitting system is designed to make every job quick and easy. it provides a revolutionary alternative for the professional plumber and gasfitter. 02_DUOPEX GAS
Rapidmain Installation Guide
Rapidmain Installation Guide Aluminium Compressed Air Pipe Work Installation Guide Trafalgar Court, Waterloo Ind Estate, Widnes Cheshire. UK. Ref: Rapidmain installation guide 4b Index 1. Rapidmain fittings:
PANACEA P125 USER MANUAL
Basic Features Stainless steel body with 1.125 outside diameter. Will fit into wells down to 1-1/4 (schedule 80). Uses static water pressure to fill gas and sample return tubes. Maximum depth below ground
Model 130M Pneumatic Controller
Instruction MI 017-450 May 1978 Model 130M Pneumatic Controller Installation and Operation Manual Control Unit Controller Model 130M Controller is a pneumatic, shelf-mounted instrument with a separate
DataSheet. Series AA Electronic Metering Pumps. Configuration Data. Dimensions. Specifications. Model AA HI. ISO 9001 Certified
DataSheet Series AA Electronic Metering Pumps Configuration Data Model AA 9 4 1-358HI Control Code 1 --- Manual Control: Speed (stroking frequency) and stroke length manually adjustable. 7 --- Instrument
Valves. Controllers. Valves Two Types
Hydraulics Taking the Irritation out of Irrigation My plants are getting irrigated, so I m all set, right? Marcus Duck Academic Advisor, Instructor & Program Coordinator MSU s 2-year Horticulture Programs
TN-20/2007. Special Precautions for Fusing Saddle Fittings to Live PE Fuel Gas Mains Pressurized on the Basis of a 0.
TN-20/2007 Special Precautions for Fusing Saddle Fittings to Live PE Fuel Gas Mains Pressurized on the Basis of a 0.40 Design Factor Special Precautions for Fusing Saddle Fittings to Live PE Fuel Gas Mains
INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS
INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS IAPMO GUIDE CRITERIA FOR WATER HEATER SUPPLY SHUTOFF VALVE WITH A / THERMAL EXPANSION CONTROL VALVE IGC 128-2006a8 1. PURPOSE 1.1 The purpose
Practical Guide. By Steven T. Taylor, P.E., Member ASHRAE
ractical Guide The following article was published in ASHRAE Journal, March 2003. Copyright 2003 American Society of Heating, Refrigerating and Air- Conditioning Engineers, Inc. It is presented for educational
Residential Fence Tubing
Residential Fence Tubing RESIDENTIAL FENCE TUBING Approximate Pieces Price Per Foot Size O.D. Item# Gauge Weight Per Foot Per Lift Cut Less Lift Lift 1 3/8 PE 20100-18.67 91 1.30 1.13 1 3/8 Swedge 20200-18.67
VB-7212 Series. Application. Features. Applicable Literature. 5/8" O.D., 45 SAE Flared Stem Up Open, Two-Way Valves General Instructions
VB-7212 Series 5/8" O.D., 45 SAE Flared Stem Up Open, Two-Way Valves General Instructions Application VB-7212 series single seat, stem up open, two-way valves control water from 20 to 281 F (-7 to 138
Right-Angle Tube Roller Model
SPECIFICATIONS Model no. Free Speed (RPM) Throttle Rotation Max. Torque Ft-Lb Air Pressure psi Air Inlet Hose Air Flow @Free Speed Spindle Weight 909-1700 95 Lever type Reversible 240 90 1/2 NPT 1/2 I.D.
FASTENERS, CLAMPS & STRAPS
Bands...169 Buckles...170 Cable Ties...171 Clip, Ring & Pin Kits...168 Clips, Rings & Pins...168 Hose Clamps...170,171 Screw Anchor Expanders...168 Strap Tensioners & Adaptors...172 Tie Wire...172 Tie
2 1 6 SHARKBITE C ATA LO G
2 16 SHARKBITE CATALOG INDEX SHARKBITE SHARKBITE SHARKBITE SHARKBITE THE MARK OF QUALITY Lead-Free/Safety* All SharkBite fittings are made of Lead Free DZR Brass and exceed ASSE 1061 Section 1V, 4.1 Materials-Dezincification
Installation Manual. Python Vacuum Insulated Pipe. Designed and Built by: Chart Inc th Street NW New Prague, MN USA (800)
Installation Manual Python Vacuum Insulated Pipe Designed and Built by: Chart Inc. 407 7th Street NW New Prague, MN 56071 USA (800) 400-4683 Part Number 11822026 Rev. E 2017 Chart Inc. Installation Manual
VBS-9263 Series. Application. Features. Applicable Literature
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com VBS-9263 Series 1/2" and 3/4" Screwed NPT 316 Stainless Steel Stem Up Closed, Two-Way Valves General Instructions Application
OHD L-44 METHOD OF TEST FOR MEASUREMENT OF WATER PERMEABILITY OF COMPACTED PAVING MIXTURES
Page 1 of 6 METHOD OF TEST FOR MEASUREMENT OF WATER PERMEABILITY OF COMPACTED PAVING MIXTURES 1. SCOPE A. This test method covers the laboratory determination of the water conductivity of a compacted asphalt
HydroSwage System and Tooling
Page 1 of 9 HydroSwage System and Tooling Haskel International, Inc. has over 50 years of hydraulic and pneumatic engineering experience in the design and manufacturing of a wide range of products and
New MacLean-Dixie 4-1/2 Strength Squared Pipe Piles/Anchors (Patent Pending) for Compression and Tension Applications
Page: 1 of 6 New MacLean-Dixie 4-1/2 Strength Squared Pipe Piles/Anchors (Patent Pending) for Compression and Tension Applications P45 Series 4-1/2 (O.D.) Schedule 40 Pipe Pile Torque Capacity (ft-lbs)
Hydro-Mech Bridge Plug
Manual No: 0620000303 Revision: F Approved By: Quality Engineer Date: 2014-9-9 Hydro-Mech Bridge Plug DESCRIPTION: Map Hydro-Mech Bridge Plug is hydraulically actuated and mechanically set. Compact, with
VB-7263 Series. Application. Features. Applicable Literature
TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com VB-7263 Series 1/2" to 2" Screwed NPT Stainless Steel Trim with Teflon Disc Stem Up Closed, Two-Way Valves General Instructions
GX SYSTEM. Technical documentation 0756EN
GX SYSTEM Technical documentation 0756EN GX System SUMMARY 1 GX System 1 Advantages and features 1 Technical features - GX connection 2 Technical features - Pipes 6 Technical features - Fittings 8 Technical
Section GATE VALVES
Section 02521 PART 1 GENERAL 1.01 SUMMARY This Section includes the furnishing and installation of gate valves for isolation and dead-end service as shown on Plans and as specified herein. 1.02 MEASUREMENT
Parts Manual Tubing - Tubing - Tubing Accessories
Parts Manual Tubing - Tubing - Tubing Accessories Page 1 of 6 1.01 125042 38FS-41003 150017193 TUBING,3/8,FS,.380IDX.535OD,300FT 1.02 125039 38FS-31002 150017196 TUBING,1/4,FS,.265IDX.420OD,100FT 1.03
Polyethylene Valves for Natural Gas.
Polyethylene Valves for Natural Gas. Providing valves and equipment to the world s energy markets for over 00 years. Polyethylene Valves Made in the U.S.A. The POLYBALL valve is manufactured at our Mansura,
Solenoid valves, two-step on/off Type PMLX REFRIGERATION AND AIR CONDITIONING. Technical leaflet
Solenoid valves, two-step on/off PMLX REFRIGERATION AND AIR CONDITIONING Technical leaflet Contents Page Introduction........................................................................................3
New MacLean-Dixie 3-1/2 Strength Squared Pipe Piles/Anchors (Patent Pending) for Compression and Tension Applications
Page: 1 of 6 New MacLean-Dixie 3-1/2 Strength Squared Pipe Piles/Anchors (Patent Pending) for Compression and Tension Applications ICC AC358 Acceptance Criteria for Foundation Systems and Devices APPLICATION
-FRU FREEZE RESISTANT WATER VALVE COOLERS SYSTEM
I N S TA L L AT I O N / I MN SA TA I N TL EL NAT AIN OC N E / MI AN IS NT RE UN CA TN I CO E N SI N S T R U C T I O N S INSTALLATION INSTRUCTIONS FOR -FRU OPTION Important: Read all instructions and refer
Effective Date: December 2017 Void After: December 2018
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the
TDUX Inflatable Duct Sealing System 1.0 General Product Information
TDUX I N S T A L L A T I O N I N S T R U C T I O N Inflatable Duct Sealing System 1.0 General Product Information The TDUX inflatable duct sealing system is a wraparound, inflatable, mastic-lined bladder
CPVC Transition Fittings - Female Adapter. CPVC X LEAD FREE BRASS Lead Free Max working pressure F ASTM D 2846
CPVC Transition Fittings - Female Adapter STD4703BTLF12 1/2 CPVC X 1/2 FIP 25 250 CPVC Transition Fittings - Female Adapter STD4703BTLF34 3/4 CPVC X 3/4 FIP 25 250 CPVC Transition Fittings - Female Adapter
tel: fax: web:
Tri-Flex 2 Five-Cell Permeability Test System For high volume commercial laboratory testing, the Tri-Flex 2 Five-Cell Permeability Test System offers the user the capabilities to test up to five samples
Alternative Methods For Making CoCoRaHS Snow Water Content Measurements. Prepared by: Rick Fleetwood Environment Canada Updated Feb 2015
Alternative Methods For Making CoCoRaHS Snow Water Content Measurements Prepared by: Rick Fleetwood Environment Canada Updated Feb 2015 Introduction This document will cover off two alternate methods for
VB-7273 Series. Application. Features. Applicable Literature
VB-7273 Series 1/2" to 2" Screwed NPT Stainless Steel Trim Stem Up Open, Two-Way Valves General Instructions Application VB-7273 series single seat, stem down to close, two-way valves control water from
Barcol-Air BRM Radiant Module
Barcol-Air BRM Radiant Module General The high capacity Radiant Cooling Module BRM is based on the principles of the radiant cooling technology. Due to the purpose designed profile and the geometry of
Geotech 1.66 Auto-Reclaimer Installation and Operation
Geotech 1.66 Auto-Reclaimer Installation and Operation Rev 10/19/12 Part # 16600165 TABLE OF CONTENTS CHAPTER 1: SYSTEM DESCRIPTION... 3 FUNCTION AND THEORY... 3 SYSTEM COMPONENTS... 4 CHAPTER 2: SYSTEM
Geotech 1.66 Auto-Reclaimer
Geotech 1.66 Auto-Reclaimer Installation and Operation Rev 9 8/31/06 Part # 16600165 TABLE OF CONTENTS CHAPTER 1: SYSTEM DESCRIPTION... 3 FUNCTION AND THEORY... 3 SYSTEM COMPONENTS... 4 CHAPTER 2: SYSTEM
Homestead Series 820 AWWA Butterfly Valves
Homestead Series 820 AWWA Butterfly Valves Dependable Valves for Water & Wastewater Service BODY: The ductile iron body meets or exceeds the design strength requirements of the AWWA C504 standards. Flange
Viega ProPress Systems Installation Manual
Viega ProPress Systems Installation Manual The global leader in plumbing, heating and pipe joining systems Heritage of quality, vision for the future Viega s heritage of superiority demands nothing but
4/8/2009 Earth Sheltered Dwellings Considerations Orientation to sun and wind to Topography Soil type Groundwater level 2
Alternative Housing Why build an alternative house? Energy savings Building cost savings New innovative design Alternative Types Earth Sheltered Dwellings Geodesic Domes Insulating Concrete Forms (ICF)
THE PERFECT PRESSURE DROP TRAP PRIMER
THE PERFECT PRESSURE DROP TRAP PRIMER FIGURE NO. 2694 PATENT NO. 9,708,808 Regularly furnished in Lead-Free Brass as shown (back). Optional finishes available in Chrome (front), Nickel, or Stainless Steel
HVAC CATALOG VOLUME II. Quality. Products for. the HVAC. Professional
HVAC CATALOG VOLUME II Quality Products for the HVAC Professional Tubing... 1 Pipe Insulation... 2-8 Wrot/ACR Solder Joint Fittings... 9 Forged Brass & Cast Pressure Fittings... 10-12 Wrot DWV Solder Fittings...
Cold Press joint technology has been around for over a century.
Cold Press joint technology has been around for over a century. Since the first design was patented, there have been a number of important evolutionary modifications. The focus of these improvements have
VB-7213 Series. Application. Features. Applicable Literature. 1/2" to 2" Screwed NPT Stem Up Open, Two-Way Valves General Instructions
VB-7213 Series 1/2" to 2" Screwed NPT Stem Up Open, Two-Way Valves General Instructions Application VB-7213 series single seat, stem up open, two-way valves control water from 20 to 281 F (-7 to 138 C)