PRODUCT CATALOGUE 2010

Transcription

1 PRODUCT CATALOGUE 2010

2 Page 2 TABLE OF CONTENTS PRODUCT LINE DESCRIPTION PAGE NO. COMPANY PROFILE Brief Company History, NEXOR, About Us, Mission NEXOR HDPE Pressure Mains Pipe For Potable Water System. 5 No need to Buttweld HDPE Pipe NEXOR HDPE Butt Fusion Pipes For Potable Water System 6 NEXOR HDPE Pipes for Service Connections For Potable Water System 9 NEXOR PP Push Fit Compression Fittings The easiest way to connect PE Pipes 10 NEXOR PE Socket Fusion Fittings Ideal for internal plumbing pipes 15 6 NEXOR Brass Threaded PE Socket Fusion Fittings Ideal for internal plumbing pipes 17 7 NEXOR Spigot Fittings HDPE Fittings for buttwelding 19 8 NEXOR Standard G.I. Nipple Schedule 40 (HD) Standard 38 9 NEXOR Hot Water Lines PPR piping system for hot water systems PN 20 pressure rating NEXOR Annular Corrugated Pipes For drainage, sewage & other gravity flow applications 46

3 Page 3 COMPANY PROFILE BRIEF COMPANY HISTORY Junni Industries Inc. is a corporate entity, duly registered on August 1, 2003, with the Securities and Exchange Commission under and in accordance with provisions of the Corporation Code of the Philippines with Securities and Exchange Commission (SEC) Registration No. CS , with domicile address at 4th Floor NEXOR Bldg., 1677 Quezon Ave., West Triangle Q.C. The incorporators of Junni Industries Inc. are, Engr. Franklin C. Tan, President and Chairman of the Board from 2003 to present. Engr. Johannes Burke C. Tan is the General Manager and the Board s Secretary while Ms. Katheryn T. Vallester is the Treasurer. Technological innovations in the field of plastic piping technology and the unavailability of the use of such among pipe manufacturer in the Philippines motivated the start-up of the company. Observing the low level of quality among pipes produced in the Philippines and the success in the local market of expensive though superior in quality of imported pipes such as Rehau and Polymutan, the company recognizes the demand for quality pipes in the local market and it is determined to fill the void. To date, the corporation s financial operation from 2003 to the present has been very promising, despite the fact that the Philippine economy is experiencing difficult times. Sales and profits of the corporation have remained unabated despite the downtrend in the Philippine economy. Our success is a result of our hard work, building a reputation as a reliable provider of quality products such as HDPE pipes and fittings, and winning the customer s confidence. Setting and maintaining a high quality standard of plastic products can be only possible through the use of the latest and modern manufacturing equipment. Junni Industries Inc. uses extruders from the renowned German company Krauss Maffei. Our technologically superior extruders guarantee superior performance. In addition, our production lines are equipped with ultrasonic thickness measuring devices, melt filtration, and gravimetric dosing units. Junni Industries Incorporated is affiliated with Cofta Mouldings Corporation the pioneer and still the number one manufacturer of monoblock chairs, tables, drawers, PC twin wall roofing PVC foam sheets, etc.

4 Page 4 In January 2006, Junni Industries Inc. introduced NEXOR brand of HDPE pipes. NEXOR pipes have superior surface finish, concentric inner and outer pipe walls, and close tolerance wall thickness. At Junni Industries Inc., we understand that in manufacturing pipes, the slightest dip in the thickness tolerance of the pipe defines the weakest point of the entire piping system. A pipe is as good as its weakest point or its thinnest wall section. With NEXOR pipes being stringently inspected for quality, Junni Industries aims to break in to the market by providing high quality pipes. ABOUT US Pipe failure goes beyond the cost of simply replacing the pipe. In most applications, the shortsighted savings incurred in using inferior pipe materials is negated by the high cost of repair and re-installation of pipes. In internal plumbing applications for instance, expensive earth movements and or building structure adjustments have to be done in order to repair faulty pipe systems. Failure of pipes in agricultural applications may suspend the delivery of plant nutrients leading to poor harvests. Undetected leakage due to pipe failure is perhaps the worst with using inferior pipe. Leakage in buried pipes imposes a high tax in terms of energy costs in pumping water. In recognition of the fact that pipe failure goes beyond the cost of simply replacing the pipe, NEXOR brand of pipes was established to stand for quality pipes at reasonable prices. We, the makers of NEXOR pipes, are committed to practicing the highest level of engineering standards and to providing superior customer support. Should you have product inquiries or requirements, feel free to contact us or you may visit our website at for further information. MISSION Junni Industries Inc. envisions becoming the authority in the manufacture, design, and installation of piping systems in the Philippines for applications including potable water, drainage, sewage, gas, and others through constant investment in piping technology, practicing the highest level of engineering standards, and providing superior customer support..

5 HDPE PRESSURE MAINS For Potable Water Page 5 SPECIFICATION : PN 10 PRODUCT PROPERTIES & FEATURES : High Flow Capacity Durable» Weather Resistance» Chemical Resistance Safe Easy to install Economical SIZES AVAILABLE : 63 mm Ø x 315 mm Ø STANDARD COLOR : Black with blue stripes, Black or Blue INSTALLATION : Push Fit Type Connection. No equipment needed REPLACES : Class 150 upvc Mains 6 METER LENGTHS LONG LENGTHS OUTSIDE LENGTH PN 10 (150 PSI) LENGTH PN 10 (150 PSI) DIAMETER (m) (m) THICKNESS PRICE THICKNESS PRICE , , , , , not yet not yet available available

6 Page 6 HDPE BUTT FUSION PIPES SPECIFICATION : PRODUCT PROPERTIES & FEATURES : - High Flow Capacity - Durable» Weather Resistance» Chemical Resistance - Safe, easy to install and economical SIZES AVAILABLE STANDARD COLOR INSTALLATION : 63mm Ø up to 1000mm Ø : Black with blue stripes, Black or Blue : Butt Fusion (equipment and electric generator required) 1 Meter interval NEXOR 63mm x 3.7mm PN16 PE80 " water " ISO 4427 D-Outside Note: We produce PE 80 and PE 100 HDPE pipes I. STRAIGHT LENGTHS OUTSIDE SDR DIAMETER COIL LENGTH THICKNESS PRICE/ THICKNESS PRICE/ THICKNESS PRICE/ THICKNESS PRICE/ PC. PC. PC. PC , , , , , , , , , , , , , , , ,793.00

7 Page 7 HDPE BUTT FUSION PIPES II. STRAIGHT LENGTHS OUTSIDE SDR DIAMETER COIL LENGTH THICKNESS PRICE/ THICKNESS PRICE/ THICKNESS PRICE/ THICKNESS PRICE/ PC. PC. PC. PC , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , II. STRAIGHT LENGTHS (LARGE DIAMETER) OUTSIDE COIL SDR DIAMETER LENGTH (mtr) THICKNESS PRICE/ THICKNESS PRICE/ THICKNESS PRICE/ THICKNESS PRICE/ PC. PC. PC. PC , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,996.00

8 Page 8 HDPE BUTT FUSION PIPES WELDED SEAM A good seem with a prominent, high bead. Under actual site conditions, the size, shape and evenness of the welded seam can only be checked visually. Other methods of examination are based on samples cut from the seam and studied in a laboratory. However a seam welded by following the instructions has been found to be reliable. The adjacent column shows some examples of welded seams. The bead is too low ( not enough welding pressure ). A deep split in the bead Should the seam be unsatisfactory, it is cut off ( not enough heat, or and the ends rewelded together again. transition time too long ). The bead is too narrow and high ( too much pressure ). Improper alignment. Max. permitted deviation is 10% of the wall thickness. Different wall thickness. Bevelling the thicker one is recommended. The welded materials have different melting temperatures/ heating times.

9 HDPE PIPES FOR SERVICE CONNECTIONS Page 9 SDR 17 (PN 8) SDR 13.6 (PN 10) Nominal OD ID Thk Coil Weight PRICE Nominal OD ID Thk Coil Weight PRICE Size Length (m) (kgs.) Size Length (m) (kgs.) 1/ , / , / , / , / , / , , , / , / , / , / , , , / , / , , , , , SDR 11 (PN 12.5) SDR 9 (PN 16) Nominal OD ID Thk Coil Weight PRICE Nominal OD ID Thk Coil Weight PRICE Size Length (m) (kgs.) Size Length (m) (kgs.) 1/ , / , / , / , / , / , , / , / , / , / , , / , / , , , / , , , / , , ,268.10

10 Page 10 PP PUSH FIT COMPRESSION FITTINGS NEXOR PP compression fittings are the easiest way to connect PE pipes. No equipment is necessary, just simply insert and twist to connect pipes. Twisting action compresses clinching ring which buries itself into the pipe for a secure fit. Male Threaded Adaptor 20mm x 1/ mm x 3/ mm x mm x 1 1/ mm x 1 1/ mm x mm x 2 1/ mm x mm x 4 1, Female Threaded Adaptor 20mm x 1/ mm x 3/ mm x mm x 1 1/ mm x 1 1/ mm x mm x 2 1/ mm x 3 1, Straight Coupler 20mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 50mm mm x 63mm mm x 75mm mm x 90mm 1, mm x 110mm 3,932.00

11 Page 11 PP PUSH FIT COMPRESSION FITTINGS Reducing Coupler 25mm x 20mm mm x 20mm mm x 25mm mm x 20mm mm x 25mm mm x 32mm mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 25mm mm x 32mm mm x 40mm mm x 50mm mm x 40mm mm x 50mm mm x 63mm mm x 63mm 1, mm x 75mm 1, mm x 90mm 2, Equal Tee 20mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 50mm mm x 63mm mm x 75mm 1, mm x 90mm 2, mm x 110mm 3, Reducing Tee 25mm x 20mm mm x 20mm mm x 25mm mm x 25mm mm x 32mm mm x 25mm mm x 32mm mm x 40mm mm 32mm mm x 40mm mm x 50mm mm x 40mm 1, mm x 50mm 1, mm x 63mm 1, mm x 63mm 1, mm x 75mm 1,441.00

12 Page 12 PP PUSH FIT COMPRESSION FITTINGS Female Tee 20mm x 1/ mm x 3/ mm x mm x 1 1/ mm 1 1/ mm x mm x 2 1/2 1, mm x 3 2, Male Tee 20mm x 1/ mm x 3/ mm x mm x 1 1/ mm 1 1/ mm x mm x 2 1/2 1, mm x 3 2, Equal Elbow 20mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 50mm mm x 63mm mm x 75mm mm x 90mm 1, mm x 110mm 2,391.00

13 Page 13 PP PUSH FIT COMPRESSION FITTINGS Female Elbow 20mm x 1/ mm x 3/ mm x mm x 1 1/ mm 1 1/ mm x mm x 2 1/ mm x 3 1, Male Elbow 20mm x 1/ mm x 3/ mm x mm x 1 1/ mm 1 1/ mm x mm x 2 1/ mm x 3 1, End Cap 20mm mm mm mm mm mm mm mm mm 1,446.00

14 Page 14 PP PUSH FIT COMPRESSION FITTINGS Clamp Saddle 32mm x 1/ mm x 3/ mm x mm x 1/ mm x 3/ mm x mm x 1/ mm x 3/ mm x mm x 1/ mm x 3/ mm x mm x 1 1/ mm x 1/ mm x 3/ mm x mm x 1 1/ mm x 1 1/ mm x mm x 1/ mm x 3/ mm x mm x 1 1/ mmx 1 1/ mm x mm x 1/ mm x 3/ mm mm x 1 1/ mm x 1 1/ mm x mm x 1/ mm x 3/ mm x mm x 1 1/ mm x 1 1/ mm x 2 1, mm x 3/4 2, mm x 1 2, mm x 2 2, Tapping Ferrule Ferrule 1 1/4 x 25mm /4 x 32mm

15 Page 15 SPIGOT FITTINGS NEXOR Spigot Fittings are HDPE fittings for butt welding. Injection moulded and fabricated types available. Product Features: Made of PE 100 Better hydraulic flow than mitered fittings Better pressure holding capacity than mitered fitting Does not rely on the skill of personnel fabricating mitered fittings NEXOR Equal Tee (Segmented) Spigot Fittings INSTALLATION: Butt fusion (equipment and electric generator required) NOTES : Difficult to install in challenging terrain, poor weather condition DELIVERY : Usually takes 1 to 3 weeks

16 Page 16 SPIGOT FITTINGS NEXOR Equal Tee (Segmented) Spigot Fittings OD Segmented Tees 90 degrees L1 α OD L L OD L1 L L The pipes used for manufacturing these fittings shall be in accordance with ISO , and the butt fusion machine shall be in accordance with ISO LEGEND: OD nominal outside diameter L tubular length of fitting L1 nominal lengths of fitting branch to axis α nominal angle of fitting (+ 2o) For tees fabricated out of pipe segments, the following derating rules for the calculation of the PN shall apply: PN = ƒt x PNpipe where: ƒt = derating factor for tee having a value of 0.5 PNpipe = nominal pipe pressure I. Material: a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C - Maximum allowable hydrostatic design stress: 8 MPa b.) Extrusion Compound Properties: - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% II. Prior to acceptance and delivery, fittings and gasket shall pass the required test as PNS specifications.

17 Page 17 SPIGOT FITTINGS NEXOR Equal Tee (Moulded) Spigot Fittings ODb L1 L2 ODm L1 L L1 INSTALLATION : Butt fusion (equipment and electric generator required) NOTES : Difficult to install in challenging terrain, poor weather condition DELIVERY : Usually takes 1 to 3 weeks LEGEND: ODm = Outside diameter main ODb = Outside diameter branch L = Length moulded block L1 = Length of pipe L2 = Radius of moulded block TEE 90, EQUAL MAIN L L1 L I. Material: a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C - Maximum allowable hydrostatic design stress: 8 MPa b.) Extrusion Compound Properties: - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% II. Prior to acceptance and delivery, fittings and gasket shall pass the required test as PNS specifications

18 Page 18 SPIGOT FITTINGS NEXOR Tee Reducer (Branch Type) Spigot Fittings INSTALLATION : Butt fusion (equipment and electric generator required) NOTES : Difficult to install in challenging terrain, poor weather condition DELIVERY : Usually takes 1 to 3 weeks I. Material: a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C ODb - Maximum allowable hydrostatic design stress: 8 MPa b.) Extrusion Compound Properties: L ı - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% ODm II. Prior to acceptance and delivery, fittings and gasket shall pass the required test as PNS specifications. L LEGEND: ODm = Outside diameter main pipe. ODb = Outside diameter branch pipe. L = Length of main pipe. Lı = Length of branch pipe.

19 Page 19 SPIGOT FITTINGS TEE 90, REDUCER Main Branch L L1 Main Branch L L1 Main Branch L L

20 Page 20 MOULDED SPIGOT FITTINGS NEXOR Tee Reducer (Moulded) Spigot Fittings INSTALLATION : Butt fusion (equipment and electric generator required) NOTES : Difficult to install in challenging terrain, poor weather condition DELIVERY : Usually takes 1 to 3 weeks ODb LB L1 ODm LM L LM LEGEND: ODm = Outside diameter main ODb = Outside diameter branch L LM LB L1 = Length moulded block = Length main pipe = Length of reduced pipe = Radius of moulded block

21 Page 21 MOULDED SPIGOT FITTINGS I. Material: a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C - Maximum allowable hydrostatic design stress: 8 MPa b.) Extrusion Compound Properties: - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% II. Prior to acceptance and delivery, fittings and gasket shall pass the required test as PNS specifications. TEE 90, REDUCER MAIN BRANCH L LM LB L2 MAIN BRANCH L LM LB L

22 Page 22 SPIGOT FITTINGS NEXOR Reducer Spigot Fittings INSTALLATION : Butt fusion (equipment and electric generator required) NOTES : Difficult to install in challenging terrain, poor weather condition DELIVERY : Usually takes 1 to 3 weeks D2 D1 I. Material: L/3 L/3 L/3 a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C - Maximum allowable hydrostatic design stress: 8 MPa L b.) Extrusion Compound Properties: - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% LEGEND: D1 D2 L Outside diameter main pipe Outside diameter reduced pipe Length of reducer II. Prior to acceptance and delivery, fittings and gasket shall pass the required test as PNS specifications. All units of measurements are in mm.

23 Page 23 SPIGOT FITTINGS REDUCER D1 D2 L D1 D2 L D1 D2 L

24 Page 24 STUB FLANGE SPIGOT FITTINGS HDPE Stub End INSTALLATION : Bolts and nuts. Use of allen wrench STUB END MATERIAL : Polyethylene FLANGE MATERIAL : Galvanized Mild Steel GASKET MATERIAL : Natural Rubber D I. Material: OD H L a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C - Maximum allowable hydrostatic design stress: 8 MPa b.) Extrusion Compound Properties: - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% LEGEND: II. Prior to acceptance and delivery, fittings and gasket shall pass the required test as PNS specifications. D OD L Outside diameter main pipe Outside diameter of stub end Length of stub end All units of measurements are in mm.

25 Page 25 SPIGOT FITTINGS STUB END D OD H L

26 Page 26 STUB FLANGE SPIGOT FITTINGS Galvanized Flange INSTALLATION : Bolts and nuts. Use of allen wrench STUB END MATERIAL : Polyethylene FLANGE MATERIAL : Galvanized Mild Steel GASKET MATERIAL : Natural Rubber d ID H PCD OD LEGEND: OD ID H d PCD outside diameter inside diameter height of flange diameter for bolts & nuts parallel distance between bolts All units of measurements are in mm.

27 Page 27 STUB FLANGE SPIGOT FITTINGS GALVANIZED Bolts Pipe Size OD ID PCD H d thread size number M M M M16 (5/8'') M16 (5/8'') M16 (5/8'') M16 (5/8'') M16 (5/8'') M16 (5/8'') M16 (5/8'') M20 (3/4'') M20 (3/4'') M20 (3/4'') M20 (3/4'') M20 (3/4'') M20 (3/4'') M20 (3/4'') M24 (1'') M24 (1'') M24 (1'') M27 (1 1/8") M27 (1 1/8") M27 (1 1/8") M30( 1 1/4") M30( 1 1/4") M33 (1 3/8") 28

28 Page 28 SPIGOT FITTINGS HDPE End Cap D d L LEGEND: D d L Outside diameter of pipe Depth of end cap Length of end cap End Cap D L d All units of measurements are in mm. Used for non pressurized system I. Material: a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C - Maximum allowable hydrostatic design stress: 8 MPa b.) Extrusion Compound Properties: - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% II. Prior to acceptance and delivery, fittings and gasket shall pass the re-

29 Page 29 SPIGOT FITTINGS HDPE Transition Fitting 315 mm NEXOR PIPE LEGEND: D Outside diameter of pipe ts ts d L Depth of end cap Length of end cap S SDR All units of measurements are in mm. Used for non pressurized system. L1 L = I. Material: a.) Base Compound: - Material designation : HDPE - Minimum Required Strength (MRS): 10 MPa at 50 years and 20 0 C - Maximum allowable hydrostatic design stress: 8 MPa b.) Extrusion Compound Properties: - Melt Flow Rate (MFR): - shall range from 0.2g/10min to 1.3g/10min - Minimum Density: 0.95 g/ml - Minimum Tensile Strength at Break : 34 MPa - Minimum Elongation at Break: 350% II. Prior to acceptance and delivery, fittings and gasket shall pass the required test as PNS specifications.

30 Page 30 SPIGOT FITTINGS HDPE Segmented Elbow ELBOW Bends (degrees) OD L L1 L L1 L L

31 Page 31 SPIGOT FITTINGS α L OD 30 degree L α L α L L 60 degree 90 degree O OD

32 Page 32 SPIGOT FITTINGS HDPE Segmented Elbow ELBOW Bends (degrees) OD L L1 L L1 L L

33 Page 33 SPIGOT FITTINGS α L 22.5 degree OD L α L α L1 L1 45 degree 90 degree OD OD

34 Page 34 Product Features: STANDARD G.I. NIPPLE Material : Schedule 40 (HD) Standard Thread : ISO 7 Packaging : Threads with plastic wrap, packaged in boxes G.I. Nipple TOTAL LENGTH INCH mm 1/2 MIN. QTY. 3/4 MIN. QTY. 1 MIN. QTY. PRICE 1-1/4 MIN. QTY. 1-1/2 MIN. close N/A 1 1/ N/A QTY. 2 MIN / / / / QTY.

35 Page 35 PIPES FOR INTERNAL PLUMBING PRODUCT INSTALLATION NOTES LENGTH STRAIGHT LENGTHS FOR INTERNAL PLUMBING USE SOCKET FUSION FITTINGS NEED TO USE SOCKET FUSION WELDER 4 METERS SDR Standard Dimension Ratio Nominal Size Outside Diameter Inside Diameter Thickness Weight (kg) 1/2" Pressure Rating 128psi 9 Pressure Rating 230psi 3/4" " /4" /2" " /2" " , " /2" /4" " /4" /2" " /2" , " , "

36 Page 36 PE SOCKET FUSION FITTINGS NEXOR PE Socket fusion fittings are ideal for internal plumbing pipes. Socket fusion fittings are recommended for making straight length pipe connections. Socket fusion fittings and pipes are joined by simultaneously heating the external surface of the pipe and the internal surface of the fitting. Equal Tee 20mm mm mm mm mm Equal Elbow 20mm x 20mm mm x 25mm mm x 32mm mm x 50mm Straight Coupler 63mm x 63mm mm x 20mm mm x 25mm mm x 32mm mm x 50mm mm x 63mm 82.00

37 PE SOCKET FUSION FITTINGS Page 37 Reducing Coupler 25mm x 20mm mm x 20mm mm x 25mm mm x 32mm mm x 32mm mm x 50mm End Cap 20mm mm mm Pipe Stiffener 20mm mm 2.00 Reducing Tee 25mm x 20mm mm x 20mm mm x 25mm

38 Page 38 BRASS THREADED PE SOCKET FUSION FITTINGS NEXOR Brass threaded PE Socket fusion fittings are ideal for internal plumbing pipes. Socket fusion fittings are recommended for making straight length pipe connections. Socket fusion fittings and pipes are joined by simultaneously heating the external surface of the pipe and the internal surface of the fitting. Male Threaded Adaptor 20mm x 1/ mm x 1/ mm x 3/ mm x 3/ mm x Female Threaded Adaptor 20mm x 1/ mm x 1/ mm x 3/ mm x 3/ mm x Female Tee 20mm x 1/ mm x 1/ mm x 3/ mm x 3/ mm x

39 Page 39 BRASS THREADED PE SOCKET FUSION FITTINGS Female Elbow 20mm x 1/ mm x 1/ mm x 3/ mm x 3/ mm x Male Tee 20mm x 1/ mm x 1/ mm x 3/ mm x 3/ mm x Male Elbow 20mm x 1/ mm x 1/ mm x 3/ mm x 3/ mm x

40 Page 40 HOT WATER LINES Product Features: PPR Piping System for hot water systems PN 20 Pressure Rating For hot water up to 90 degree Celcius Long Service Life Hygenic Pipe (PN 20) 20mm x 3.4mm mm x 4.2mm mm x 5.4mm mm x 6.7mm 50mm x 8.4mm 63mm x 10.5mm Elbow 90 o 20mm mm mm mm mm mm Elbow 45 o 20mm mm mm mm mm mm

41 Page 41 HOT WATER LINES Equal Tee 20mm mm mm mm mm mm Reducing Tee 25mm x 20mm mm 20mm mm 25mm mm x 20mm mm x 25mm mm x 32mm mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 50mm

42 Page 42 HOT WATER LINES Straight Coupler 20mm mm mm mm mm mm Reducer 25mm x 20mm mm x 20mm mm x 25mm mm x 20mm mm x 25mm mm x 32mm mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 20mm mm x 25mm mm x 32mm mm x 40mm mm x 50mm

43 Page 43 HOT WATER LINES End Cap 20mm mm mm mm mm mm Cross 20mm mm mm mm mm - 63mm - Long Syphon 20mm mm mm mm 50mm 63mm

44 Page 44 HOT WATER LINES Bypass Bend 20mm mm mm mm 50mm 63mm Reducing Elbow 25mm x 20mm mm x 20mm mm x 25mm Female Threaded Adaptor 20mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x mm x 1 1/4 1, mm x 1 1/2 1, mm x 2 2,161.00

45 Page 45 HOT WATER LINES Female Threaded Tee 20mm x 1/ mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x Female Threaded Elbow 20mm x 1/ mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x Male Threaded Adaptor 20mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x mm x 1 1/4 1, mm x 1 1/2 1, mm x 2 2,816.00

46 Page 46 HOT WATER LINES Male Threaded Tee 20mm x 1/ mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x Male Threaded Elbow 20mm x 1/ mm x 1/ mm x 3/ mm x 1/ mm x 3/ mm x Low Footed Clamp 20mm mm mm mm mm mm Welding Machine Pipe Cutter/Scissors 20mm to 63mm 11, mm to 110mm 40, mm to 40mm 2, mm to 63mm 7, mm to 125mm 20,288.00

47 Page 47 ANNULAR CORRUGATED PIPES FOR DRAINAGE, SEWAGE, AND OTHER GRAVITY FLOW APPLICATIONS ADVANTAGES Ecpnomical, easy to use, flexible, impact resistant, corrosion free, UV resistant, high load capacity OPTIONS LOAD BEARING CAPACITY 1. Single WALL Economical, ideal for foot traffic or light loads. (Golf courses, gardens, etc.) 2. Double Wall High load bearing capacity, ideal for roads and other demanding applications PERFORATION 1. Non-perforated pipes 2. Perforated pipes for subsurface water collection, drainage, etc. JOINTS/CONNECTIONS 1. Non-water tight use of split couplers, economical 2. Water tight bell ends with rubber rings, or couplers with rubber rings I. COILED ANNULAR CORRUGATED PIPES (LONG LENGTHS) SINGLE WALL Size Length (m) Non-Perforated Perforated 110 OD , , OD , ,737.50

48 Page 48 ANNULAR CORRUGATED PIPES II. ANNULAR CORRUGATED PIPES WITH SPLIT COUPLER ENDS (NON-WATER TIGHT) SINGLE WALL DOUBLE WALL Size Length (m) Non-Perforated Perforated Non-Perforated Perforated 110 OD 5.8 N/A N/A , OD 5.8 N/A N/A 1, , ID 5.8 3, , , , ID 5.8 3, , , , ID 5.8 4, , , , ID 5.8 7, , , , ID , , , , ID , , , , III. ANNULAR CORRUGATED PIPES WITH BELL ENDS (W/ RUBBER RING WATER TIGHT) DOUBLE WALL Size Length (m) Non-Perforated Perforated 110 OD 5.8 1, , OD 5.8 1, , ID 5.8 5, , ID 5.8 6, , ID 5.8 8, , ID , , ID , , ID , , NOTES: 1. Split coupler end is for not so water tight applications such as irrigation, rain water collection, perforated systems, etc.

49 Plant Address: Sitio Rizza, Brgy. Pinugay, Antipolo City Office Address: 4th Floor NEXOR Bldg., 1677 Quezon Ave., West Triangle, Quezon City Phone: (02) TeleFax: (02) Website: