SHASTA COUNTY OFFICE OF EDUCATION CODE OF SAFE PRACTICES (CONSTRUCTION) Name of Project
|
|
|
- Willis Hines
- 5 years ago
- Views:
Transcription
1
2 SHASTA COUNTY OFFICE OF EDUCATION CODE OF SAFE PRACTICES (CONSTRUCTION) Name of Project GENERAL* 1. All employees shall follow these safe practices rules, render every possible aid to safe operations, and report all unsafe conditions or practices to their Supervisor or the Alternate Responsible Person. 2. Supervisors shall insist on employees observing and obeying all rules, regulations, and orders as is necessary to insure the safe conduct of the work, and shall take such action as is necessary to obtain observance. 3. All employees shall be given frequent accident prevention instructions. Instruction should be given at least every 30 working days. 4. Any employee known to be under the influence of drugs or intoxicating substances which impair the employee's ability to safely perform the assigned duties shall not be allowed on the job. 5. Horseplay, scuffling, and other acts which tend to have an adverse influence on the safety or well-being of the employees shall be prohibited. 6. Work shall be well planned and supervised to prevent injuries in the handling o material and in working together with equipment. 7. No employee shall knowingly be permitted or required to work while the employee's ability or alertness is so impaired by fatigue, illness, or other causes that it might unnecessarily expose the employee or others to injury. 8. Employees shall not enter manholes, underground vaults, chambers, tanks, silos, crawlspaces, or other similar places that receive little ventilation, unless it has been determined that it is safe to enter. 9. Employees shall be instructed to ensure that all guards and other protective devises are in proper places and adjusted, and shall report deficiencies promptly to the Supervisor or Alternate Responsible Person. 10. Crowding or pushing when boarding or laving any vehicle or other conveyance shall be prohibited. *California Construction Safety Orders, Appendix A, Plate A-3
3 11. Employees shall not handle or tamper with any electrical equipment, machinery, or air or water lines in manner not within the scope of their duties, unless they have received instructions from their Supervisors. 12. All injuries shall be reported promptly to the Supervisors or the Alternate Responsible Person so that arrangement can be made for medical or first aid treatment. 13. When lifting heavy objects, use the large muscles of the leg instead of the smaller muscles of the back. 14. Inappropriate footwear or shoes with thin or badly worn soles shall not be worn. 15. Material, tools, or other objects shall not be thrown from buildings or structures until proper precautions are taken to protect others from the falling objects. 16. Employees shall cleanse thoroughly after handling hazardous substances, and follow special instruction from authorized sources. 17. Hod carriers should avoid the use of extension ladders when carrying loads. Such ladders may provide adequate strength, but the rung position and rope arrangement may make such climbing difficult and hazardous for this trade. 18. Work shall be so arranged that employees are able to face ladder and use both hands while climbing. 19. Gasoline shall not be used for cleaning purposes. 20. No burning, welding, or other source of ignition shall be applied to any enclosed tank or vessel, even if there are some openings, until it has first been determined that no possibility of explosion exists, and authority for the work is obtained from the Supervisors or Alternative Responsible Person. 21. Any damage to scaffolds, falsework, or other supporting structures shall be immediately reported to the supervisor or Alternate Responsible Person, and repaired before use.
4 USE OF TOOLS AND EQUIPMENT 1. All tools and equipment shall be maintained in good condition. 2. Damaged tools or equipment shall be removed from service and tagged "DEFECTIVE." 3. Pipe or Stillson wrenches shall not be used as a substitute for other wrenches. 4. Only appropriate tools shall be used for the job. 5. Wrenches shall not be altered by the addition of handle-extensions or "cheaters." 6. Files shall be equipped with handles and not used to punch or pry. 7. A screwdriver shall not be used as a chisel. 8. Wheelbarrows shall not be pushed with handles in an upright position. 9. Portable electric tools shall not be lifted or lowered by means of the power cords. Robes shall be used. 10. Electric cords shall not be exposed to damage from vehicles. 11. In locations where the use of a portable power tool is difficult, the tool shall be supported y means of a rope or similar support of adequate strength. MACHINERY AND VEHICLES 1. Only authorized employees shall operate machinery or equipment. 2. Loose or frayed clothing, or long hair, dangling ties, finger rings, etc. shall not be worn around moving machinery or other sources of entanglement. 3. Machinery shall not be serviced, repaired or adjusted while in operation, nor shall oiling of moving parts be attempted, except on equipment that is designed or fitted with safeguards to prot3ect the employee performing the work. 4. Where appropriate, lock-out procedures shall be used. 5. Employees shall not work under vehicles supported by jacks or chain hoists, without protective blocking that will prevent injury if jacks or hoists should fail. 6. Air hoses shall not be disconnected at compressors until hose line has been bled.
5 7. All excavating shall be visually inspected before backfilling, to ensure that it is safe to backfill. 8. Excavating equipment shall not be operated near tops of cuts, banks, and cliffs if employees are working below. 9. Tractors, bulldozers, scrapers and carry all shall not operate where there is possibility of overturning in dangerous areas like edges of deep fills, cut banks, and steep slopes. 10. When loading where there is a probability of dangerous slides or movement of material, the wheel or treads of loading equipment, other than that riding on rails, should be turned in the direction which will facilitate escape in case of danger, except in a situation where this position of the wheels or treads would cause a greater operational hazard. ROOFING OPERATIONS 1. Knotted hand lines should not be used. 2. Roofers tending kettles, or carrying buckets of hot tar, shall wear gloves that fit snugly at the wrists, and long sleeved shirts fastened at the wrists. 3. At no time should a roofer, while handling or exposed to injury from hot tar, work without a shirt or appropriate footwear. 4. Appropriate portable fire extinguishers shall be kept at or near the kettle, attached, if practicable, to the tongue of the kettle, away from the danger zone. 5. Kettle covers should be equipped with a handle that projects at least fourteen (14) inches away from the surface of the cover or lid. 6. Kettle covers shall be closed and latched when in transit and the kettle should be slopproof when cover is closed. 7. When parked, means shall be provided to prevent inadvertent movement of the kettle. 8. Ladders should be used with great caution, and roof gutters should not be depended upon for support. 9. Workers handling buckets of hot tar should not carry anything that will interfere with the safety of this operation. 10. The gallows frame shall be securely anchored before hoisting materials. 11. Only muscular power shall be used to hoist materials by means of a gallows frame. A winch or power hoist shall not be used.
Adelanto Elementary School District Code of Safe Practices
Adelanto Elementary School District Code of Safe Practices (Rev 4/30/2018) Adelanto Elementary School District CODE OF SAFE PRACTICES (Rev 4/30/2018) Our general workplace safety and health practices can
New Employee Safety Indoctrination Checklist
New Employee Safety Indoctrination Checklist Emergency Response Training Read and understand the Facility s Emergency Response Action Plan Complete Emergency Response Training Locate the Facility s Evacuation
CONSTRUCTION SAFETY PROGRAM FOR. Golder Acoustics Inc.
CONSTRUCTION SAFETY PROGRAM FOR Golder Acoustics Inc. TABLE OF CONTENTS Topic... Page Safety and Health Policy... 2 Safety and Health Objectives... 3 Job Site Inspections... 4 Contractor Safety Administrator...
Original Date of Issue: 04/09
POLICIES AND PROCEDURES DEPARTMENT: Environmental Health and Safety SUBJECT: Electrical Safety Program Original Date of Issue: 04/09 Reviewed 12/2011 Revised 12/2011 BACKGROUND ELECTRIC SHOCK It is well
MAINTENANCE MECHANIC RCF
REPAIRING AND REPLACING VALVES AND COILS MAINTENANCE MECHANIC Activity Hazard Identification Required Precautions 1. Walking to and from work site. 1a. Back ache; overexertion from carrying heavy weight.
CONTRACTOR SAFETY RULES
CONTRACTOR SAFETY RULES CONTRACTOR SAFETY RULES AND REGULATIONS This manual sets forth policy with regards to contractor safety. Each Quinn facility consists of one or several diverse operations under
Injury and Illness Prevention Program
has established an (IIPP) designed to provide a safe and hazard-free environment for all employees, clients and visitors. This program is administered and maintained by s Risk Management Department. A
Fall Protection and Elevated Work
Program No: SP-010 Page 1 1.0 PURPOSE AND INTRODUCTION Fall Protection and Elevated Work To establish fall protection safety procedures for Pitt County Schools employees engaged in any of the following
SUBCONTRACTOR SAFETY PROGRAM. Property of Downing
SUBCONTRACTOR SAFETY PROGRAM Property of Downing 2018-1 - Downing Construction, Inc. Safety Program Table of Contents Page(s) Legal Disclaimer 3 Letter from the Partners 4 Safety Mission Statement 4 Accountability
BOILER MECHANIC//SR. BOILER MECHANIC
WORKING IN STEAM MANHOLES Activity Hazard Identification Required Precautions 1. Driving to and from work site. 1. Motor vehicle accident; striking pedestrians, bicyclists, or individuals using rollerblades.
EMPLOYEE SAFETY ORIENTATION - PHYSICAL PLANT, RESIDENCE
Name Department Initial Orientation Date Supervisor Review Instructions: Check off each section once you have read and discussed it with your Supervisor. EMPLOYEE SAFETY ORIENTATION - PHYSICAL PLANT, RESIDENCE
techconnect CARPENTRY Objectives Unit 2 Workplace Safety TechConnect - STUDENT WORKBOOK 2-1 Workplace Safety - Unit 2
Unit 2 Workplace Safety techconnect One of the keys to working in any industry is the safety and health of the workers. The carpentry industry can be a dangerous industry in which to work if you do not
DEPARTMENT OF THEATRE AND DANCE CALIFORNIA STATE UNIVERSITY, FULLERTON
DEPARTMENT OF THEATRE AND DANCE CALIFORNIA STATE UNIVERSITY, FULLERTON SCENIC LAB SAFETY PROCEDURES (CPAC 154) 1. POLICY The Department Scenic Lab is a facility, which supports courses in scenic design
OSHA s new walking working surfaces standards
OSHA s new walking working surfaces standards changes and new requirements Inspection of walking working surfaces 1910.22(d) Regularly and as needed and correct, repair, or guard against hazardous conditions;
CHAPTER 10 FALL PROTECTION
CHAPTER 10 FALL PROTECTION A. INTRODUCTION... 1 B. CHAPTER-SPECIFIC ROLES and RESPONSIBILITIES... 2 C. HAZARD IDENTIFICATION... 3 1. Job Hazard Analysis (Jha).... 3 2. Fall Hazards... 3 D. HAZARD CONTROL...
Contractor handbook. Purpose
Page no: 1 / 6 Contractor handbook Purpose Mitie aims to ensure that the highest levels of performance are achieved by all persons working for us or on our behalf. We require the same level of performance
1.0 Scope and Application. 2.0 Definitions. Cal Poly Risk Management Confined Space Program Page 1
Page 1 1.0 Scope and Application The following procedures describe safe operating practices in confined spaces. These may be sewers, pipelines, tanks, boiler compartments, ducts, vaults, pits, vats, bins
Walking and Working Surfaces: Comprehensive Training
Walking and Working Surfaces: Comprehensive Training PROGRAM SYNOPSIS: To ensure workers are provided with safe working and traveling surfaces, OSHA has developed and recently updated its regulation 29
2. The purpose of this program is to achieve the following objectives:
Section 16A. Lockout and Tagout Program 1. In the course of their duties, personnel at the TFREC may need to secure controls, switches, and equipment in order to prevent injury caused by the sudden, unexpected
FALL PROTECTION / ELEVATED WORK
SEPTEMBER CORE REFRESHER HSE TOOL BOX FALL PROTECTION / ELEVATED WORK FALL PROTECTION Falls from elevations are one of the most common causes of death in this industry. OSHA requires fall protection when
Confined Space Entry
Confined Space Entry Purpose The purpose of this document is to establish methods to identify confined spaces, classify them according to their risks, and establish guidelines necessary for the safe preparation,
PAC. Risk Management Resources. The cost of Workers Compensation can be controlled. Also visit WELLAdvised
PAC Risk Management Resources The cost of Workers Compensation can be controlled Also visit www.babbins.com WELLAdvised Safety Guidelines for Home Visits 1) Do not give consumers your home phone number.
Reporting, Recording & more Walking Working Surfaces Local Emphasis Program Your Questions
Reporting, Recording & more Walking Working Surfaces Local Emphasis Program Your Questions As of January 1, 2015, employers must report the following to OSHA: All work-related fatalities within 8 hours
OSHA Federal Standards October 1, 2016 September 30, 2017
OSHA Federal Standards October 1, 2016 September 30, 2017 29 CFR 1926 SUBPARTS 29 CFR 1926. C M L L E M M E X M MOST FREQUENTLY CITED SERIOUS VIOLATIONS IN CONSTRUCTION 2017.501(b)(13) FALL PROTECTION
Confined Space Entry
Confined Space Entry Purpose The purpose of this chapter is to establish methods to identify confined spaces, classify them according to their risks, and establish guidelines necessary for the safe preparation,
DREW UNIVERSITY FALL PROTECTION PROCEDURE (DRAFT 12/11)
PURPOSE The objective of this policy & guideline is to eliminate the potential for injuries and fatalities to employees and contractors resulting from falls from elevated work areas at Drew University
MAINTENANCE MECHANIC RCF
WORKING ON ATC EQUIPMENT MAINTENANCE MECHANIC Activity Hazard Identification Required Precautions 1. Driving to and from work site. 1. Motor vehicle accident; striking pedestrians, bicyclists, or individuals
The Corporation of the Town of Tecumseh
The Corporation of the Town of Tecumseh POLICY MANUAL POLICY NUMBER: 59/11 EFFECTIVE DATE: October 11, 2011 SUPERCEDES: PPC 23/07 - April 24, 2007 APPROVAL: RCM October 11, 2011 (RCM-343/11) SUBJECT: Confined
1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT
TABLE OF CONTENTS 1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT This symbol means: ATTENTION - BECOME ALERT YOUR SAFETY IS INVOLVED. When you see this symbol
TABLE OF CONTENTS PART 2 - CONFINED SPACES
May 11, 2006 TABLE OF CONTENTS PART 2 - CONFINED SPACES Page DEFINITIONS... 2-1 GENERAL... 2-2 RESPONSIBILITIES... 2-2 HAZARD ASSESSMENT AND WORK PROCEDURES... 2-3 IDENTIFICATION AND ENTRY PERMITS... 2-3
SAFETY POLICY Office Address 5195 W. 58 th Ave. Unit F Arvada, CO 80002
SAFETY POLICY Office Address 5195 W. 58 th Ave. Unit F Arvada, Office CO Address 80002 5195 W. 58 th Ave. Unit F Arvada, CO 80002 303-223-5716 www.valiantcc.com info@valiantcc.com 303-223-5716 info@valiantcc.com
CONFINED SPACE POLICY
Policy No. 6 THE CITY OF POMONA SAFETY POLICIES AND PROCEDURES CONFINED SPACE POLICY City Manager I. PURPOSE The purpose of the City of Pomona Confined Space Policy is to ensure that employees are adequately
Pannier Corporation Health and Safety Handbook Marking System Group Aerial Lifts Original Date: Section: Revision date: Page: 12/5/ of 11
12/5/2013 37 1 of 11 1.0 Overview Aerial lifts are commonly used in construction, inspection, athletic events and repair services to lift Pannier employees to an elevated work position. Proper operation
U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL
SAFE -14 Page 1 of 8 U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL FUNCTION Safety TOPIC Hotwork Permit Program OBJECTIVE(S): GENERAL POLICY: To provide a work atmosphere that is conducive to
Health & Safety Policy
Health & Safety Policy I. OBJECTIVE The Safety Policy of Knaggs Developers Limited is designed to comply with the Standards of the Occupational Safety and Health Act 2004, and to endeavor to maintain a
Safety Management System. Initial Revision Date: Version Revision No. 02 GENERAL SAFETY HEALTH PROVISION
Revision Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 5 Purpose This program is written to be in compliance with local regulatory requirements and provide directives
ISD #535 Rochester Public Schools
ISD #535 Rochester Public Schools Health & Safety Office Maintenance Service Building 10 9½ St SE Rochester, MN 55904 507-328-4507 Management Plan for Machine Guarding Modification Date Document Modification
The Johns Hopkins University/The Johns Hopkins Hospital Health, Safety and Environment Manual Safety Policies:
Page 1 of 6 Keywords: Airborne Combustible, Atmospheric Monitoring, Atmospheric Oxygen, Authorized Entrant, Body Harness, Combustible Gas Meter, Communication Procedure, Confined Space, CPR, Entry, Entry
CHAPTER 26 WELDING AND CUTTING
CHAPTER 26 WELDING AND CUTTING Revised 7/2010 1 WELDING AND CUTTING Responsibilities 1. The County Safety Officer is responsible for providing appropriate safety instructions for supervisor's use on welding
Scope: This plan applies to all personnel, including contractors, who enter or work in confined spaces, or supervise such activities.
11/13/1995 4 5/20/2013 1 of 10 Authority and Scope Regulation: 29 CFR 1910.146 Scope: This plan applies to all personnel, including contractors, who enter or work in confined spaces, or supervise such
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR CFR , ,
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.331 335-29 CFR 1926.302, 1926.416, 1926.417 BASIS: The National Safety Council estimates that there are at least 300 deaths
Accident Fund Insurance Company of America is dedicated to helping employers create safer work environments and as a commitment to our community has
Accident Fund Insurance Company of America is dedicated to helping employers create safer work environments and as a commitment to our community has sponsored this safety message to help keep all Habitat
Los Rios Community College District Job Safety Analysis
Required and/or recommended personal protective equipment: Gloves, non - skid rubber soled shoes, goggles, respirator, ear protection, protective clothing Ballast replacement: Obtain work order and proper
Aerial Lift Safety Program
Aerial Lift Safety Program Revision Date: 6-19-2017 TABLE OF CONTENTS Aerial Lift Safety Program 1.0 Overview... 3 2.0 Policy......3 3.0 Requirements. 3 4.0 Purpose..... 4 5.0 Scope.........4 6.0 Responsibilities........7
Confined Space Entry Procedure
Purpose The purpose of this chapter is to establish methods to identify confined spaces, classify them according to their risks, and establish guidelines necessary for the safe preparation, entry and rescue
SAFETY DIRECTIVE 3.0 REFERENCES. 3.1 See Appendix B
SAFETY DIRECTIVE Title: Hot Work Issuing Department: Town Manager s Safety Office Effective Date: September 1, 2014 Approved: Gilbert Davidson, Town Manager Type of Action: New 1.0 PURPOSE To provide proper
Safety Tips from the WorkSafe People. Building a Safety Program for Your Organization
Building a Safety Program for Your Organization 1 Content Criteria and Examples of Confined Spaces Permit-Required Confined Space Non-Permit-Required Confined Space Employer Requirements Employee Requirements
Overview. Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used
FALL PROTECTION Overview Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used Fall Protection All situations that expose personnel to
Electrical Safety Work Practices
Work Practices I. SCOPE This program covers any SOUTHWESTERN COMMUNITY COLLEGE employee that may work or be exposed to exposed electrical systems: To assure that employees are not exposed to potentially
"FALL PROTECTION IN CONSTRUCTION ENVIRONMENTS"
MAJOR PROGRAM POINTS "FALL PROTECTION IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS
User Instruction Manual For Davit Rescue System
Instructions for the following series products: Rescue Davit System Model numbers 8004000 and 8302500 User Instruction Manual For Davit Rescue System This manual should be used as part of an employee training
OP-SF-005 Confined Space Entry
Section Date Passed Resolution # Reviewed Date Repealed Resolution # Operations - Safety & Fire February 18, 2014 31230 Currently under review POLICY Entry into confined spaces can
SAFETY 101: FALL PROTECTION: REDUCING FALLS DURING RESIDENTIAL CONSTRUCTION: RE-ROOFING FACT SHEET
SAFETY 101: FALL PROTECTION: REDUCING FALLS DURING RESIDENTIAL CONSTRUCTION: RE-ROOFING FACT SHEET Re-roofing exposes workers to the hazards of demolition work at heights. With the proper fall protection,
CONFINED SPACE WRITTEN PROGRAM
CONFINED SPACE WRITTEN PROGRAM Maple River Public Schools ISD#2135 Confined Space Entry Plan (Permit Required) Maple River Public School Plan last updated: October, 2014 Authority and Scope Regulation:
New OSHA Rescue Requirements for Confined Space Retrieval: What You Should Know
New OSHA Rescue Requirements for Confined Space Retrieval: What You Should Know It is imperative to get the adequate training, to select the proper equipment, and to practice entering, exiting, and performing
New Hire Safety Orientation. Welcome to Flexicrew, our number one priority is you and your safety.
New Hire Safety Orientation Welcome to Flexicrew, our number one priority is you and your safety. 1 New Employee Responsibilities As a contract worker with Flexicrew Staffing, I understand by signing this
Student Shop Safety. University of Tennessee Safety Guide GS-005. Purpose. Scope and Applicability. Definitions and Abbreviations.
Student Shop Safety University of Tennessee Safety Guide GS-005 Document Contact: EHS Date effective: August 1, 2012 Revision Date: June 7, 2017 Purpose Machine shops are present in many departments and
: Electric Power Generation, Transmission, and Distribution. Region IV - OSHA
1910.269: Electric Power Generation, Transmission, and Distribution Region IV - OSHA Scope This standard covers the operation and maintenance of electric power generation, control, transformation transmission,
Confined Space Entry Program
Confined Space Entry Program August 2016 Table of Contents Purpose... 1 Scope and Application... 1 Responsibilities... 2 Environmental Health and Safety (EH&S)... 2 Entry Supervisor... 2 Attendant... 2
THE TLC COMPANIES. Self Inspection Program. Self Inspection. Program. Revised 12/13/2002 DC00026
THE TLC COMPANIES Self Inspection Program Self Inspection Program Table of Contents SECTION 1 INSPECTION REQUIREMENTS 1 Informal Inspection 1 General Inspection 1 SECTION 3 CONDUCTING INSPECTIONS 5 Preparation
AES Raptor, LLC Raptor R1000 Instruction Manual
AES Raptor, LLC Raptor R1000 Instruction Manual Published by AES Raptor, LLC, North Kansas City, MO AES RAPTOR COMPLETE MOBILE FALL PROTECTION SYSTEM is a registered trademark of Architectural Exterior
Hudson City School District. Student Safety Contract
Hudson City School District Student Safety Contract Purpose To all Students The following rules and regulations are extremely important to your safety in many areas of the school environment. Your instructor
Confined Space. Program Responsibilities
Confined Space CONFINED SPACE ENTRY AND RESCUE The OSHA standard on Permit-Required Confined Spaces (29 CFR 1910.146) requires employers to implement practices and procedures to protect employees from
Confined Space Entry Program 8 CCR 5157
TABLE OF CONTENTS 1. POLICY... 2 2. PURPOSE... 2 3. SCOPE... 2 4. DEFINITIONS... 2 5. CONFINED SPACES IN THE SACRAMENTO STATE... 4 6. PERMIT SPACE ENTRY - PERSONNEL RESPONSIBILITIES... 4 6.1. CONFINED
DBI SALA Confined Space Rescue Davit System
Instructions for the following series products: Rescue Davit System (See back page for specific model numbers.) User Instruction Manual For Davit Rescue System This manual should be used as part of an
"FALL PREVENTION IN THE WORKPLACE"
MAJOR PROGRAM POINTS "FALL PREVENTION IN THE WORKPLACE" Part of the "GENERAL SAFETY SERIES" Quality Safety and Health Products, for Today...and Tomorrow Outline of Major Points Covered in the "Fall Protection"
A Health and Safety Tip Sheet for School Maintenance Staff. Did you know? Step 1. Identify job hazards. Step 2. Work towards solutions
INSPECTION Health and CHECKLIST Safety Committees MAINTAINING SAFETY: A Health and Safety Tip Sheet for School Maintenance Staff 1 Maintenance and facilities staff members keep schools operational, safe,
APPENDIX A NEW HIRE TRAINING
APPENDIX A NEW HIRE TRAINING 1. CONDUCT A. All employees are ultimately responsible for their own safety and share the responsibility for the safety of their co-workers, our client's employees, and their
CONFINED SPACE ENTRY PROGRAM
CONFINED SPACE ENTRY PROGRAM 2003 ENVIRONMENTAL HEALTH AND SAFETY/RISK MANAGEMENT p1 Rev. 01/07/2003 wrk Environmental Health and Safety/Risk Management CSUCI Confined Space Entry Program TABLE OF CONTENTS
CONFINED SPACE PROGRAM
CONFINED SPACE PROGRAM A confined space, as defined in 29 CFR 1910.146: Is large enough and so configured that an employee can bodily enter and perform assigned work AND Has limited or restricted means
Safety Meeting Topic #11 Hazards of Confined Space
Safety Meeting Topic #11 Hazards of Confined Space OSHA defines confined spaces as work areas with certain features: large enough to enter and work in, limited entry and exit areas, and not designed to
Code of Practice and Instructions to Contractors Working for Viridor
Date of issue: 20 Code of Practice and Instructions to Contractors Working for Viridor Prepared by: Ian Powell Head of Safety Management 4.6.3 Revision: 2.0 Contents Introduction... 2 Legal obligations...
General Safety and Health Provisions for Construction Self Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: General Safety and Health Provisions for Construction Self Inspection Checklist Instructions:
Suitability of Work Equipment
These regulations came into effect on the 5th December 1998 and replace PUWER 1992. They cover almost all equipment used at work, including tool box tools such as hammers, knives etc. They also cover machinery
HYDRAULIC WINCH FOR AUGERS UP TO WR10 X 71 / W130 X 41 ASSEMBLY & OPERATION MANUAL
HYDRAULIC WINCH ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual
Marshall Municipal Utilities CONFINED SPACE ENTRY Effective January 1, 2011
Marshall Municipal Utilities CONFINED SPACE ENTRY Effective January 1, 2011 Purpose Marshall Municipal Utilities confined space entry program is designed to protect employees from the recognized hazards
Confined Spaces OSHA 1926 AA
Confined Spaces OSHA 1926 AA 1926.1201-1213 Confined Spaces Objectives: Understanding why the OSHA requirements are needed Identify four categories of hazards that may be present entering in confined spaces
Safety is a priority at Vault Pipelines.
Safety is a priority at Vault Pipelines. At Vault Pipelines we believe that every incident is preventable and that every task can be completed safely and efficiently. We will achieve this through our cultural
NATURAL GAS MAINTENANCE. Part 192 Subpart "M"
NATURAL GAS MAINTENANCE Part 192 Subpart "M" CONTACT INFORMATION Pamela West Pipeline Safety Specialist U.S. Department of Transportation PHMSA Inspector Training and Qualifications Main: (405) 686-2310
The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field.
Purpose The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Fall Protection and Prevention JELD-WEN Field Employees
EMPLOYEE SAFETY HANDBOOK
EMPLOYEE SAFETY HANDBOOK HSE Department Al Rumela شمس الرميلة/ Sun Policy Al Rumela شمس الرميلة/ Sun is committed to a policy to reduce and eliminate of all undesired events that could be resulting in
Why Update. OSHA updated Walking Working Standard. Who & What it Covers. Housekeeping (a) 6/25/ nd Leading cause of Workplace fatalities
OSHA updated Walking Working Standard Why Update 2nd Leading cause of Workplace fatalities $70 Billion Workers Comp Cost - US 100+ Million lost workdays/year - US Cari Gray, CSP Safety Consultant Ohio
Welding, Cutting, and Brazing
Welding, Cutting, and Brazing Hazards of Welding Operations Fire hazards Metal splatter Electric shock Explosion hazards Released gases Radiant energy Where would these hazards be found on oil and gas
Fall Protection. Fall Speed vs. Reaction Time. Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.
Fall Protection Fall Speed vs. Reaction Time Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.) In 1 second your body will fall 16 feet (4.8 mts.) By the time you
Fall Speed vs. Reaction Time
Fall Protection Fall Speed vs. Reaction Time Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.) In 1 second your body will fall 16 feet (4.8 mts.) By the time you
Work At Heights Toolkit. for Supervisors
Work At Heights Toolkit for Supervisors For Supervisors How to use this toolkit? The toolkit aims to provide information for supervisor to communicate one topic a day to workers. Pictures are for illustration
Responsibilities / Accountability
Responsibilities / Accountability What we will cover Brief history of OPP safety program OPP s commitment to safety Safety responsibilities Accountability for safety Employee expectations History of Safety
8. Fall Protection Procedures WAC
1.0 Fall Protection Introduction 8. Fall Protection Procedures WAC 296-155-245 If an employee is exposed to a fall hazard of ten (10) feet or more in height, the employee must use a fall restraint, fall
Hazard Identification and Risk Assessment Form. Risk Assessment
Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed
You must NOT touch any equipment unless you are authorised to work on or with that equipment and you have followed correct safety procedures.
SYDNEY TOWN HALL 1 HIRER & CONTRACTOR SAFETY FACT SHEET Issue 2 September 2013 www.sydneytownhall.com.au City of Sydney - Venue Management will provide and maintain a safe working environment for the health,
ARKANSAS TECH UNIVERSITY FACILITIES MANAGMENT HEALTH AND SAFETY MANUAL
FALL PROTECTION (PERSONAL FALL ARREST SYSTEMS) 15.0 The purpose of this policy is to specify procedures and training for the safety of the employees in the Facilities Management Group while working on
New Employee Safety Orientation. Presented by: Risk Management Services 2419 Cockrell, Dallas TX (972)
New Employee Safety Orientation Presented by: Risk Management Services 2419 Cockrell, Dallas TX 75215 (972) 925-4050 Welcome to a Culture of Safety! We want to help you work safely so you go home to your
Walking-Working Surfaces and Fall Protection Standards Update. OSHA General Industry
Walking-Working Surfaces and Fall Protection Standards Update OSHA General Industry Background Slips, trips, and falls account for a majority of all general industry injury incidents. Caused 849 workplace
CALIFORNIA STATE UNIVERSITY, LOS ANGELES WELDING, CUTTING, AND HOT WORK OPERATIONS. October 2007
CALIFORNIA STATE UNIVERSITY, LOS ANGELES WELDING, CUTTING, AND HOT WORK OPERATIONS October 2007 PROGRAM APPROVAL AND AUTHORIZATION James M. Rosser, President Date TABLE OF CONTENTS TITLE SECTION PURPOSE
Deans, Directors, Heads of Schools and Departments and Research Institute Directors and Managers
Working at Height 1. PURPOSE 1.1 To ensure that any work at height is carried out in accordance with the legal requirements and associated guidance. This includes the use of scaffolds, towers, ladders,
Progressive Safety Services LLC
1910.23 Guarding Floor and Wall Openings and Holes 1910.66 Powered Platforms, Manlifts and Vehicle Mounted Work Platforms. 1926.500 Fall Protection 1926.501 Duty to Have Fall Protection 1926.502 Fall Protection
accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 2 INCH BRAD NAILER Model: 7555 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
Injury and Illness Prevention Program KINGS COUNTY OFFICE OF EDUCATION
Injury and Illness Prevention Program KINGS COUNTY OFFICE OF EDUCATION INTRODUCTION In the fall of 1989 the California legislature created Senate Bill 198 (SB 198) which, in part, requires California employers
University of Delaware. Shop Safety
University of Delaware Shop Safety The first step in preventing personal injury or machine damage in the shop is to make sure that you are familiar with and know how to operate the equipment correctly.
accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 1-1/4 INCH BRAD NAILER Model: 7611 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.