Hazard Identification and Risk Assessment Form. Risk Assessment
|
|
- Candice Pitts
- 5 years ago
- Views:
Transcription
1 Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed in safe operation of each tool/machine. Restricted access to the workshop. Workshop locked shut when not present. supervised by when in the workshop. Safety boots and overalls compulsory when working in the workshop. Hearing protection, gloves and eye protection worn as required. Use of PPE actively enforced. The PPE requirements displayed at the entrance to the workshop. Emergency stops distributed around the workshop cut the power to all machines in the workshop. Power can only be reinstated once it has been reset in the s office. Guards and other safety devices on machines/tools are never defeated. Equipment is serviced and maintained as required. Faulty equipment is taken out of service until repaired satisfactorily. Equipment isolated during service or repair. Portable electric tools are 110v. Power cables are routed away from walkways. Adequate working space maintained around each machine. Long hair restrained and no loose clothing when using machines/tools. Specific precautions for some of the various machines used/activities in the workshop are detailed on the following pages. Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 1 of 9
2 Identification and Assessment Form Assessment Chemicals Fuels, Oils, lubricants, cleaning solvent, Batteries Irritation/burns to skin/eyes Dermatitis Fire, explosion Gloves and barrier creams used when handling chemicals. Hand washed when finished work with chemicals. Flammables press for storage of fuels in Jerry Cans, oils and lubricants. New batteries stored in cabinet. Battery charging carried out in well ventilated area. Parts cleaning tank never overfilled. Lid closed and pump turned off when not in use. Spills dealt with promptly. Spill absorbent provided. Wet floor signs. Used oil collected and disposed of appropriately. Plumbed in eye wash station. Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 2 of 9
3 Identification and Assessment Form Assessment Manual Handling Back injuries Muscle strains The precautions applicable to all area, plus: Significant amount of the equipment used in the workshop on lockable castors/wheels, including: o Toolboxes o Diagnostic equipment o Engine blocks o Wheelie bins o Trolley jacks o Hydraulic oil dispensers Sack truck and hand pallet truck available. Collection tanks for waste oil emptied using compressed air. Large waste oil drum moved using fork lift. Engine oil dispensed into jug and carried to vehicle. Exhaust Gases Asphyxiation Extraction hoses placed over engine exhausts. Carbon monoxide poisoning Engines running intermittently and for short durations for testing. Engines not left running unnecessarily. Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 3 of 9
4 Identification and Assessment Form Assessment Vehicle Lifts, Trolley Jacks, Engine Crane Crush injuries Slip, trip, fall supervises vehicles onto the lifts. Vehicles generally pushed into position. Lifting gear inspected annually. Safe working load (SWL) indicated and adhered to. Vehicle lifts: o End plates automatically flip down to prevent vehicles rolling off. o Lifts have built in air locks so they do not drop to the ground in the event of a failure. o Pressure has to be maintained on the button when lifting/lowering. Lift stops when button released. o Audible beep when lowering below one foot. o High visibility tape on the floor around the edges. Significant gaps covered by metal plates. Engine crane chained to the wall when not in use. Lights set in the floor for the 2m lift so that users do not have to use lead lamps. AG Block Engines Manual handling injuries Entanglement Burns/scalds Fixed on trolley on castors, so can be moved into position easily. Fans and belts guarded. Mesh guard surrounding the exhaust manifold. Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 4 of 9
5 Identification and Assessment Form Assessment Other Engines Manual handling injuries Hand injuries Rolling Road Slip, trip, fall Wheel Balancer Tyre Changer Manual Handling Entanglement Impact injuries Manual handling injuries Entanglement Explosion Lifted onto bench using hoist. Engines only used for dismantling/assembly. Engines chocked to prevent them from toppling. Plates cover the rollers when not in use. High visibility tape on the floor around the edges. Damper testers within the taped/highlighted area. Two person lift used for larger/heavier wheels. Wheel secured in place by the boss. Wheel will not spin until safety hood pulled down over tyre. Wheel spins for a short duration and is never left unattended when spinning. Two person lift used for larger/heavier wheels. Wheel clamped in place. Valve core removed before removing the tyre from the rim. Lever used to start removing the tyre, head lifts off the rest as the wheel rotates. Wheel rotates slowly. Tyres inflated to recommended pressure. Tyres never over inflated. Visibly damaged tyres taken out of service and disposed. Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 5 of 9
6 Identification and Assessment Form Assessment Battery Charging Burns to skin or eyes Explosion Batteries charge in well ventilated area. Full face shield and gloves used when topping up batteries. Plumbed in eye wash station. Compressed air Eye injuries Compressed air lines fixed to selected equipment. Skin penetration Eye protection used when using compressed air guns. Explosion Compressor located outside the workshop. Air receiver inspected annually. Supply points around the workshop, including columns dropped from the ceiling. Pedestal Drill Cuts & lacerations Eye injuries Entanglement Workpiece clamped in place for drilling. Sharp bits used. Adjustable bit guard. Gloves and eye protection worn. Emergency stop. Lockable isolator. Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 6 of 9
7 Identification and Assessment Form Assessment Bench Grinder Coil Spring Compressor Abrasions Cuts Pinch injuries Eye injuries Impact injuries Hydraulic Press Crush Injuries Housekeeping Hoses & Cables Slips, trips & falls Fire Obstructed escape Slips, trips & falls All Staff All Staff Wheels changed and dressed by competent person. The side of the wheel is never used for grinding. Flip down guard. Gloves used when holding the work piece on the moving grinding stone. Eye protection compulsory. Lockable isolator. Guard fitted around spring during use. Guard chained in place. Foot pedal operation. Manually operated using handle. Bins located in the workshop. Bins emptied at the end of each day. Workshop cleaned at the end of each day. Walkways and exits kept free of obstructions. Offices and store include cupboards and racking. Floor lights under selected lifts to reduce the need for lead lamps. Air lines retracted when no longer required. Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 7 of 9
8 Identification and Assessment Form Assessment Noise Hearing damage Nuisance to other building occupants All Staff Engines running intermittently and for short durations for testing. Engines not left running unnecessarily. Hearing protection available. Hearing protection used when running diesel engines at full revs. Compressor located outside the workshop Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 8 of 9
9 Identification and Assessment Form Action Plan Tool & Machine Work Recommended Controls & Actions Consider implementing a formal lock out tag out procedure when undertaking service and repair work on major items of equipment. Completion Date Person Responsible Revised General Noise The noise assessment for the Training Centre was completed several years ago and must be re-assessed. Manager: Date: 18 th December 2015 Produced by: Oak Leaf Safety Ltd. Ver: 1/2015 Page 9 of 9
Hazard Identification and Risk Assessment Form. Risk Assessment
Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed
More informationHazard Identification and Risk Assessment Form. Risk Assessment
Identification and Form Tool & Machine Work General Various (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed in safe operation of each
More informationHazard Identification and Risk Assessment Form. Risk Assessment
Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed
More informationHazard Identification and Risk Assessment Form. Risk Assessment
Current Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed in safe operation of each tool/machine.
More informationGarbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028. Name Date Signature. Author Jarred Hearle 30/11/2014. Reviewed John Nulty 30/11/2014
Garbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028 Name Date Signature Author Jarred Hearle 30/11/2014 Reviewed John Nulty 30/11/2014 Approved Geoff Selfe 01/12/2014 Key Safety Acts Complete a 5
More informationHigh Pressure Washer Safe Work Procedure PTES_HSE_SWP_006. Name Date Signature. Author John Nulty 12/05/2015. Reviewed Jarred Hearle 12/05/2015
High Pressure Washer Safe Work Procedure PTES_HSE_SWP_006 Name Date Signature Author John Nulty 12/05/2015 Reviewed Jarred Hearle 12/05/2015 Approved Geoff Selfe 12/05/2015 Key Safety Acts Complete a 5
More informationAutomotive Safety Checklist
Automotive Safety Checklist Facility: Address: Date: Initials: General Is your Accident Prevention Program implemented and personalized to your facility? Is the Accident Prevention Program accessible to
More informationUGRacing Formula Student Garage Risk Assessment
UGRacing Formula Student Garage Risk Assessment University of Glasgow School of Engineering Location: Formula Student Workshop Building: Rankine Building, Oakfield Avenue Glasgow G12 8LT Summary of activities
More informationRisk assessment. Assessment details. Task. Introduction. Please complete the form as fully and accurately as you can. Assessors job title
Risk assessment Introduction Please complete the form as fully and accurately as you can. Assessment details Name of organisation Assessor's name Assessors job title Any Company John Smith Manager Date
More informationJob Hazard/Safety Analysis For the Electrician
Job Hazard/Safety Analysis For the Electrician 1 INTRODUCTION Job Hazard/Safety Analysis for the Electrician is a partial list of known task performed by the professional electrician. We have placed known
More informationEHS Workplace Inspection Checklist (Ref. SOP QMS-080; EHS-010)
(Ref. SOP QMS-080; EHS-010) Form-445 Inspected by: Date of inspection Date of Report Report # Pages Area Manager: Area Inspected: General This EHS Workplace Inspection was conducted by: Scope of the Inspection:
More informationCollision Repair Shop Inspection Checklist
Collision Repair Shop Inspection Checklist Note: This is a sample inspection chesklist only, and may mot include all appropriate inspection items. The Occupational Health and Safety Regulation specifies
More informationWestern Sydney University Safety Inspection Checklist - Laboratory Environments
Western Sydney University Safety Inspection Checklist - Laboratory Environments Useful Hint: To maximise the benefits that can be gained from a workplace inspection activity read the Western Sydney University
More informationPotential hazards People at risk and how? Actions already in place Further action required Action by
Risk Assessment Flat Roof Repair Prepared by Oracle Managed Services For: BAM FM On: 24/02/2017 Review date: N/A Potential hazards People at risk and how? Actions already in place Further action required
More information1b. Slipping; tripping; getting knocked into by pedestrians.
MAINTAINING AND REPAIRING HYDRAULIC AND TRACTION PASSENGER AND FREIGHT ELEVATORS AND HANDICAP EQUIPMENT Activity Hazard Identification Required Precautions 1. Walking to and from work site. 1a. Back ache;
More informationFLYING OBJECTS MANUAL HANDLING EXCESSIVE NOISE
JOB NO: PROJECT: DATE: SWMS NO: SWMS 002 PREPARED BY: Ian Hartley REVISED BY: Nick Bragg & Cameron McNeil ACTIVITY: STUMP REMOVAL SUPERVISED BY: REVISION DATE: April 2016 MINIMUM PERSONAL PROTECTIVE EQUIPMENT
More informationRisk Management Resources
Risk Management Resources Machine Guarding Name: Notes: Electrical Systems: Fire Prevention Are circuit breakers accessible to personnel, protected from physical damage, and located away from ignitable
More informationCUSTODIAL Safety Inspection Checklist
CUSTODIAL Safety Inspection Checklist Priority 1 Any condition which is life-threatening, or may cause injury, or permanent disability Priority 2 Any condition which may cause serious, but non-disabling
More informationCITY AND COUNTY OF DENVER CR&CF RISK UNIT Compressed Gas Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.11 Compressed Gas Safety Standard 1.0 Introduction 2.0 Scope This standard has been developed to protect all City and County of Denver employees and contractors
More informationC-Consequence, P Probability, R-Risk Rating Value Page 2 of 2
General Procedure SE-GEN-04 azard nalysis & ssessment, Identification of Environmental spect and Impact ssessment P-474 / R / 01 Rev : 02 Date: 0.01.2012 CTIVITY RISK SSESSMENT WORKSEET Work ctivity: ocation:
More informationOperation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039. Name Date Signature. Author Jarred Hearle 27/11/2015
Operation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039 Name Date Signature Author Jarred Hearle 27/11/2015 Reviewed FMG Site Team 27/11/2015 ---------- Approved Geoff Selfe 27/11/2015
More informationOSHA Office of Training and Education 2
The Occupational Safety and Health Administration aims to ensure employee safety and health in the United States by working with employers and employees to create better working environments. Since its
More informationDEPARTMENT SAFETY RULES AND PROCEDURES
DEPARTMENT SAFETY RULES AND PROCEDURES 1. Working Hours 1.1. Work is primarily performed in the student machine shop under the direct supervision of a technician or faculty advisor weekdays between 8 am-
More information14. Personal Protection Chapter , WAC
14. Personal Protection Chapter 296-800-160, WAC 1.0 Introduction PLU will provide most required personal protective equipment (PPE). The employee may be required to provide PPE that is of a personal nature
More informationCHAPTER 26 WELDING AND CUTTING
CHAPTER 26 WELDING AND CUTTING Revised 7/2010 1 WELDING AND CUTTING Responsibilities 1. The County Safety Officer is responsible for providing appropriate safety instructions for supervisor's use on welding
More informationSAFE WORK METHOD STATEMENT Part B
SAFE WORK METHOD STATEMENT Part B SWMS No.: 01 WORK ACTIVITY DESCRIPTION: Door Installation All FORESEEABLE OHS & ENVIRONMENTAL HAZARDS & RISKS ASSOSSIATED WITH THE WORKS MUST BE ASSESSED & ALLOCATED CONTROLS
More informationtechconnect CARPENTRY Objectives Unit 2 Workplace Safety TechConnect - STUDENT WORKBOOK 2-1 Workplace Safety - Unit 2
Unit 2 Workplace Safety techconnect One of the keys to working in any industry is the safety and health of the workers. The carpentry industry can be a dangerous industry in which to work if you do not
More information4WD ACCESSORIES BONUS CARRY BAG 100L AIR COMPRESSOR INSTRUCTION MANUAL
4WD ACCESSORIES BONUS CARRY BAG 100L AIR COMPRESSOR INSTRUCTION MANUAL Contents Page WARRANTY DETAILS... 3 REPAIR AND REFURBISHED GOODS OR PARTS NOTICE... 3 WELCOME... 4 INTENDED USE... 5 CONTENTS... 5
More informationSafe Work Method Statement LRB TREE SERVICES 6 Behland St, Kearneys Spring QLD, 4350 ABN
JOB NO: PROJECT: DATE: 1/1/2018 SWMS NO: SWMS 001.1 PREPARED BY: LUKE BLINCO REVISED BY: ACTIVITY: TREE REMOVAL & PRUNING SIGNED BY: REVISION DATE: MINIMUM PERSONAL PROTECTIVE EQUIPMENT (PPE) REQUIREMENTS
More informationHAZARD IDENTIFICATION AND RISK ANALYSIS RECORD
HAZARD IDENTIFICATION AND RISK ANALYSIS RECORD Location: Company Wide Date of Assessment: 04 April 2017 Revision No.: 0 Description of planned work or activity: HIRA Register Attendees: see attached tool-box
More informationRisk Assessment Underwritten For:
Competition Organising Partner: CITB /SkillBuild Competition Skills: Bricklaying SKILLBUILD Risk Assessment Venue: Regional Competitions Event Dates: 0 April 9 June 017 Written by PM: Donna Havers Risk
More informationWINDMILL (pre-start) HAZARD INSPECTION CHECKLIST
Windmill Hazard Inspection Checklist WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST Authorised by: LOCATION OF INSPECTION...... Inspected By (1)........... (2)..... PRINT PRINT Signature (1):. (2)....
More informationU.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL
SAFE -14 Page 1 of 8 U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL FUNCTION Safety TOPIC Hotwork Permit Program OBJECTIVE(S): GENERAL POLICY: To provide a work atmosphere that is conducive to
More informationLecture Demonstrations Safety Manual & New Staff Induction
Lecture Demonstrations Safety Manual & New Staff Induction Overview The lecture demonstrations team provides and maintains demonstrations to lectures, tutorials and outreach. Demonstrations and equipment
More informationMAINTENANCE MECHANIC RCF
REPAIRING AND REPLACING VALVES AND COILS MAINTENANCE MECHANIC Activity Hazard Identification Required Precautions 1. Walking to and from work site. 1a. Back ache; overexertion from carrying heavy weight.
More informationLaboratory Self Inspection Checklist LAB01
Laboratory Self Inspection Checklist LAB01 General Chemical/Biological Laboratories Location Assessor Date This core checklist is provided by the Health and Safety Department as a template, which provides
More informationJob Hazard/Safety Analysis For the Carpenter
Job Hazard/Safety Analysis For the Carpenter 1 INTRODUCTION Job Hazard/Safety Analysis for the Carpenter is a partial list of known task performed by the professional carpenter. We have placed the tasks
More informationFlexfence Swaging Unit. Product Manual. Release 02/16.
Product Manual www.ingalcivil.com.au 1.0 Safety Precautions 1.1 Personal Protection While operating this equipment it is recommended that the following personal protective equipment be worn; Long sleeve
More information1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT
TABLE OF CONTENTS 1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT This symbol means: ATTENTION - BECOME ALERT YOUR SAFETY IS INVOLVED. When you see this symbol
More informationLABORATORY SAFETY. A general overview
LABORATORY SAFETY A general overview INTRODUCTION Environmental protection, Occupational Safety and Health are the Responsibility of all staff, students and collaborators working at ETH. OBJECTIVES General
More informationSurface exploration drilling
Checklist Surface exploration drilling This checklist is intended to assist employers to identify common hazards and manage risks associated with surface exploration drilling. June 2017 Background In surface
More informationUniversity College Dublin Machinery/Equipment Risk Assessment Template
1. General Information Name of Person(s) carrying out assessment and their position Principal Investigator / Supervisor / Head of School or Unit (Person responsible for ensuring safety) Date of assessment
More informationOVERVIEW OF RESTAURANT SAFETY
OVERVIEW OF RESTAURANT SAFETY Restaurants and other eating and drinking businesses employ a very large number of people in the State of California, and many of these employers are under 20 years of age.
More informationHealth and Safety Guidance Note No 37
Health and Safety Guidance Note No 37 THE SAFE USE AND STORAGE OF GAS CYLINDERS Accidents involving gas cylinders can cause serious injury or even death. The legal term for gas cylinders is transportable
More informationNEBOSH International General Certificate Paper-2
A worker is manually loading boxes of components onto metal shelves. Identify FOUR types of injury that the worker could suffer while carrying out this task. (4) The four types of injuries include; spinal
More informationCENTRAL PLANT HEATING/CHILLED WATER OPERATOR Ref. Code: C-WO-4
CENTRAL PLANT HEATING/CHILLED WATER OPERATOR Ref. Code: C-WO-4 OPERATING OF AUXILIARY EQUIPMENT Activity Hazard Identification Required Precautions 1. Inspecting boilers. 1a. Slipping on oily or wet floor.
More informationPLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO HIGH LEVEL LIGHT UNITS
PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO HIGH LEVEL LIGHT UNITS Project: (insert Client) Replacement/ Repair of high level light units/ high
More informationSuitability of Work Equipment
These regulations came into effect on the 5th December 1998 and replace PUWER 1992. They cover almost all equipment used at work, including tool box tools such as hammers, knives etc. They also cover machinery
More informationSafety Powder Spray Systems
Instruction Sheet P/N 107 952C Safety Powder Spray Systems 1. Introduction This section contains general safety instructions for using your Nordson equipment. Task- and equipment-specific warnings are
More informationHandout Activity: HA107
Engines: Motive Power Types: Handout Activity: HA107 Student/Intern information: Name Date Class Identifying hazards Summary A workshop is a hazardous environment. The objective of this procedure is to
More informationHEALTH AND SAFETY MANUAL
HEALTH AND SAFETY MANUAL Title: Abrasive Blasting Approved by: Greg Savoy Rev. 11/1/08 1 Purpose/Scope: The purpose of this program is to provide safe guidelines for the operation and maintenance of abrasive
More informationPPE and Tools PPE and Tools
PPE and Tools PPE and Tools PPE Definition Personal protective equipment (PPE) refers to protective clothing, helmets, goggles, or other garments or equipment designed to protect the wearer's body from
More informationNew Employee Safety Indoctrination Checklist
New Employee Safety Indoctrination Checklist Emergency Response Training Read and understand the Facility s Emergency Response Action Plan Complete Emergency Response Training Locate the Facility s Evacuation
More informationBOILER MECHANIC//SR. BOILER MECHANIC
WORKING IN STEAM MANHOLES Activity Hazard Identification Required Precautions 1. Driving to and from work site. 1. Motor vehicle accident; striking pedestrians, bicyclists, or individuals using rollerblades.
More informationJob Safety and Environmental Analysis (JSEA)/Safe Work Method Statement (SWMS)
Job Safety and Environmental Analysis (JSEA)/Safe Work Method Statement (SWMS) Part 1: Project and Task Identification Process: Initiators of JSEAs are responsible for consulting the Project Supervisor,
More informationOWNER S MANUAL. Page: 1 of 8
Air Needle Scaler OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal
More informationMAINTENANCE MECHANIC RCF
WORKING ON ATC EQUIPMENT MAINTENANCE MECHANIC Activity Hazard Identification Required Precautions 1. Driving to and from work site. 1. Motor vehicle accident; striking pedestrians, bicyclists, or individuals
More informationTRADE AREA: ELECTRICAL INDUSTRY
TRADE AREA: ELECTRICAL INDUSTRY Some possible workplace hazards and possible ways for Host employers and Apprentices/Trainees in controlling these hazards. What are possible hazards? What could be possible
More informationCompressed Gases Storage and Handling Safety Policy. Individual Unit Function: Safety Procedure No.: SOP-0103 Page: 1 of 6
Procedure No.: SOP-0103 Page: 1 of 6 MIDGA Reviewed: 07/09/18 Effective: 1/14/98 Supersedes: Original Preparer: Owner: Approver: Safety Safety Safety 1. PURPOSE The purpose of this procedure is to establish
More informationBasic Safety Orientation. University of Illinois at Urbana-Champaign
Basic Safety Orientation Basic Safety Orientation This orientation is General Knowledge only. Further training is required to meet hazard specific training requirements. For more information, please contact
More informationStandard Operating Procedure
Procedure Type: Creation Date: Revision Date: Standard 12/22/2014 02/19/2016 Purpose: Ensure that the removal of an anthill around a wellhead is performed in a safe and controlled manner. Scope: This SOP
More informationISD #535 Rochester Public Schools
ISD #535 Rochester Public Schools Health & Safety Office Maintenance Service Building 10 9½ St SE Rochester, MN 55904 507-328-4507 Management Plan for Machine Guarding Modification Date Document Modification
More informationLAKE ARROWHEAD COMMUNITY SERVICES DISTRICT STANDARD OPERATING PROCEDURES FACILITY SAFETY The following procedures are to be used by all District employees when working in the District facilities or with
More informationContractor Hazard Identification and Control Guide
Exposure to Asbestos Containing Materials (ACM) Accidental disturbance or removal of ACM. Asbestos Containing Materials are to be removed outside school hours. No DET employees, students or visitors are
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT WATER PUMP - PETROL Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationHealthandSafetyOntario.ca. Hazard: Compressed Gases. Hazard: Compressed Air. Hazard: Noise
Preparing a Boat for Body Work or Repainting Preparing boats for body work or repainting involves many hazards to the eyes, skin, hearing, lungs, etc. Working with fiberglass has many potential inhalable
More informationSAFE WORK INSTRUCTION
(P.P.E.) Date issued on site: Ensure all Personal Protective Equipment conforms to Australian Standards and WorkCover NSW requirements. N0:SWI001 ACTIVITY Providing P.P.E HAZARDS Identify process to be
More informationInstructions for completing the Unit Operations Lab safety inspections using the Safety Inspection Checklist
Instructions for completing the Unit Operations Lab safety inspections using the Safety Inspection Checklist This checklist includes four sections: General Lab Safety; Safety Equipment Checklist; CM4110
More informationJOB HAZARD ANALYSIS FOR PPE
JOB HAZARD ANALYSIS FOR PPE (PERSONAL PROTECTIVE EQUIPMENT) (MAINTENANCE) INTRODUCTION This Job Hazard/Safety Analysis has been conducted and prepared for the use of Maintenance personnel. This is a partial
More informationWELDING, CUTTING AND BRAZING
- 1 - WELDING, CUTTING AND BRAZING Are only authorized and trained personnel permitted to use welding, cutting or brazing equipment? Does each operator have a copy of the appropriate operating instructions
More informationRockhampton Office Brisbane Office Tarong Site. Barron Gorge Hydro PS Kareeya Hydro PS Mica Creek PS
Business Procedure Hot Work Document Number OHS-PROC-128 This document applies to the following sites: All Sites Rockhampton Office Brisbane Office Tarong Site Barron Gorge Hydro PS Kareeya Hydro PS Mica
More informationHazards Requiring Attention: AS AT Friday, 1 April Next Review Saturday, 1 April Total Hazards Recorded 43. Critical Risk Hazards 0
EF26 Risk Assessment Kubota U35-4 s Requiring Attention: AS AT Friday, 1 April 2016 0 Next Review Saturday, 1 April 2017 Total s Recorded 43 Critical Risk s 0 High Risk s 0 Moderate Risk s 10 Low Risk
More informationHazards Requiring Attention: AS AT Friday, 29 January Next Review Saturday, 28 January Total Hazards Recorded 39. Critical Risk Hazards 0
EF26 Risk Assessment CAT Excavator Hazards Requiring Attention: AS AT Friday, 29 January 2016 0 Next Review Saturday, 28 January 2017 Total Hazards Recorded 39 Critical Risk Hazards 0 High Risk Hazards
More informationSafety Services Guidance. Guidance on: The Provision and Use of Work Equipment Regulations 1998 (PUWER)
Guidance on: The Provision and Use of Work Equipment Regulations 1998 (PUWER) Key word(s) : Work equipment. Using, maintaining and repairing. Information, instruction and supervision. Risk Assessment.
More informationSafe Work Method Statement
Company Name: Safe Work Method Statement Site Address: Other Details: Contractor: Activity/Trade: Electrician Date: TASKS List the tasks required to perform the activity in sequence carried out. Entry
More informationStandard Operating Procedure #COE-SOP-0001 Chemical Fume Hood Operation
Standard Operating Procedure # Chemical Fume Hood Operation Facility: NMSU College of Engineering Laboratories Written by: Juanita Miller, Safety Specialist, miljgh@nmsu.edu (575)-646-1292 Scope: This
More informationPLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO LOW LEVEL LIGHT UNITS
PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO LOW LEVEL LIGHT UNITS Project: Insert Client Repair/ Replacement of low level light units/ low level
More informationJACKHAMMER SAFETY TRAINING
JACKHAMMER SAFETY TRAINING The aim of the instructions is to provide you with knowledge of how to use the Pneumatic breaker in an efficient, safe way. The instructions also give you advice and tell you
More informationJob Hazard Analysis Analysis by:
Job Analysis Possible s or Task Machinery e.g. Mowers Chainsaws Grinders Floor polisher Power tools Weed trimmers Sweepers Snow blowers Hedge trimmer Tiller Auto scrubbers Burnishers Ford tractor Sand
More informationDocument: APA HSE GP Tx Version: 0.01 Date: 04/03/2013 Review by: 26/03/2014 Page 1 of 11 pages
SAFE WORK METHOD STATEMENT WORKSHOP FABRICATION HSE NET NAT SWMS APAND00033 APT AM Holdings Pty. Ltd. [ABN] 95124754383 APA Group Principal Contractor (PC) Level 19, HSBC Building Subcontractor 580 George
More informationPotable Water Truck Safe Work Procedure PTES_HSE_SWP_041. Name Date Signature. Author Geoff Selfe 25/01/2016. Reviewed Solomon Site 25/01/
Potable Water Truck Safe Work Procedure PTES_HSE_SWP_041 Name Date Signature Author Geoff Selfe 25/01/2016 Reviewed Solomon Site 25/01/2016 ----- Approved Michael Garkaklis 25/01/2016 Key Safety Acts Complete
More informationSAFE WORK METHOD STATEMENT Part 1 CONCRETE SAWING
SAFE WORK METHOD STATEMENT Part 1 CONCRETE SAWING Personal Protective Equipment Foot Hearing High Visibility Head Eye Face Hand Protective Clothing Breathing Normal Requirements: Safety footwear, hearing
More informationPOLICY & PROCEDURE #502 EFFECTIVE DATE: 6/5/02 LAST REVISED: 7/12/12 LAST REVIEWED: 7/8/15
1.0 PURPOSE PLANT OPERATIONS AND MAINTENANCE, CENTRAL PLANT PERSONNEL ARE RESPONSIBLE FOR USING THE IN ACCOMPLISHING THE VARIOUS JOB TASKS ESTABLISHED IN THEIR JOB DESCRIPTION. THIS POLICY AND PROCEDURE
More informationHand and Power Tools
Hand and Power Tools Short description This section outlines the guidance for assessing and controlling hazards associated with hand and power tools. Contact person Andrew Richardson Name HSEQ Functional
More informationHow severely could the risk hurt someone? Low/Insignificant First aid
Safe Work Method Statement No: WMS-0 Task: Operate Diesel Road Saw This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia) Pty Ltd
More information1/2 in. AIR IMPACT WRENCH (TWIN HAMMER)
1/2 in. AIR IMPACT WRENCH (TWIN HAMMER) WARNING Read Operator s Manual. Do not operate equipment until you have read this Operator s Manual for Safety, Assembly/Operation and Maintenance Instructions.
More informationRugged Powered Bin Lifter. Operating Manual
Rugged Powered Bin Lifter Operating Manual Rugged Powered Bin Lifter Operating Manual OM0016E/2 This manual contains important safety, installation and operating instructions for this unit. Read this manual
More informationESSENTIAL SAFETY RESOURCES
ESSENTIAL SAFETY RESOURCES GS-3001 ABRASIVE BLASTING Originator: Safety Advisor s Signature: Type Name Approval: HSE Manager s Signature: Type Name Approval: Operations Manager s Signature: Type Name TABLE
More informationHydraulic Vehicle Positioning Jack
User Manual [Revision 1.0 February 2018] READ THIS MANUAL CAREFULLY BEFORE USE FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. KEEP THIS MANUAL FOR FUTURE REFERENCE. Products
More informationDoc No: WELDHOT Midland Engineering Co., Inc. Initial Issue Date 12/14/15 Safety Management System
Revision Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 7 PURPOSE To provide guidelines for the safe operation of welding, cutting and hot work of equipment, and to itemize
More informationOPERATION and MAINTENANCE Guide
Catalog No. AIR1000 Winch and Hoist OPERATION and MAINTENANCE Guide Cat. No. AIR1000 1250 Lb. Single Line Pull READ THIS BEFORE OPERATING UNIT INSTALLATION: Mount on clean, flat surface. Use 1/2" mounting
More informationThis training does not attempt to cover all safety regulations or precautions.
This training does not attempt to cover all safety regulations or precautions. For additional safety regulations and precautions, see the following standards: American Welding Society (AWS) American National
More informationHORIZONTAL BEAM AND VERTICAL PANEL SAWS
FACT SHEET HORIZONTAL BEAM AND VERTICAL PANEL SAWS HORIZONTAL BEAM PANEL SAW Horizontal beam panel saws are used to cut panels into pieces and it can cut multiple panels at the same time. Multiple panels
More informationPotential risk of injury to staff
Register Fire, Earthquake - other Emergencies Manual Handling and Repetitive Work Repetitive, Forceful Work Poor Housekeeping Not Wearing PPE (Personal Protective Equipment) Potential risk of injury to
More informationIndustry Code: Alberta Small Employer OHS Legislated Requirements
This document is a guideline only. Employers have a responsibility of assessing all applicable occupational health and safety legislation, for the tasks they are performing. Services in this industry can
More information75 Years of Health and Safety Guidance
H&S Guide: 60 Working Risks Personal Protective Equipment Personal Protective Equipment (also known as PPE) Employers have duties concerning the provision and use of personal protective equipment at work.
More informationPLANT RISK ASSESSMENT
PLANT RISK ASSESSMENT Forktruck: Year of Manufacture Make: Model: Serial : TCM FD30T3 Attachment: Name: Mfg: Model : Owner: Business/Organisation: Address: This header page and the following 5 pages have
More informationTask/Step Potential Hazards Recommended Safe Job Procedures
JSA No.: 08-18-14-006 JOB SAFETY ANALYSIS Position Title: Bus Washer Department: Wash Bay Work Location(s): Parking Lot Shop Wash Bay Person(s) Performing This Job: Bus Washers Analysis Start Date: 08/18/2014
More informationSAFETY TRAINING LEAFLET 02 BASIC RULES FOR SAFETY AND GOOD HOUSEKEEPING
SAFETY TRAINING LEAFLET 02 BASIC RULES FOR SAFETY AND GOOD HOUSEKEEPING Doc 23.02/18 EUROPEAN INDUSTRIAL GASES ASSOCIATION AISBL AVENUE DES ARTS 3-5 B 1210 BRUSSELS Tel: +32 2 217 70 98 Fax: +32 2 219
More informationSEMEMI SQA Unit Code H2B7 04 Assisting in the installation of compressed air equipment
Assisting in the installation of compressed air equipment Overview This unit identifies the competences you need to assist in the installation of compressed air equipment and systems, in accordance with
More information