LABORATORY TEST AND CALIBRATION EQUIPMENT

Transcription

1 WATER METER TEST BENCH LABORATORY TEST AND CALIBRATION EQUIPMENT 62

2 WATER METER STATIC PRESSURE TESTING EQUIPMENT Statik Basınç Test Ekipmanı Static Pressure Test Equipment Series: AYSU SBT AYSU is a registered trademark and trademark assurance and manufactured with advanced technology and unique design according to OIML R49 and EN standards. All of the devices are traceable and it's calibration certified by ISO / IEC Water Meters "Water Pressure Test" Static Pressure Test Equipment TRADEMARK MODEL/TYPE EUROTEST AY-40SPT YEAR 2016 SERIAL NR A test shall be performed, the results of which are capable of demonstrating leakproof performance, equivalent to an applied pressure of at least 1,6 MAP for one minute. (230 V, bar, 6l/min), Meters should be able to show without any breakdown, any leak, infiltration in their walls and permanent deormation when the maximum working pressure for which the meters are enforced continuously and correctly. Test bench is capable of executing the tests detailed in EN Standart Hydraulics pressure is raised up to 1,6 times higher than that of meter (IB highest) and kept in this level for 15 minutes. It is controlled whether there is a physical damage or water leak through outside and display unit in meters. Hydraulics pressure is raised to 2 times of the meter's (IB highest) value and kept in this level for one minute, the flow rate during the examination should be zero. info@euro-met.com.tr 63

3 Loss of Pressure Test Equipment Aysu-Basınç Kaybı Test Cihazı Loss of Pressure Test Equipment Series: AYSU BKT AYSU is a registered trademark and trademark assurance and manufactured with advanced technology and unique design according to OIML R49 and EN standards. All of the devices are traceable and it's calibration certified by ISO / IEC Water Meters; "Loss of Pressure" Test Testing Equipment TRADEMARK MODEL/TYPE EUROTEST AY40LP YEAR 2016 SERIAL NR The highest loss of pressure should not be above 63 kpa (0,63 bar) under the rated operating conditions (ROC) If the meter has any filter or strainer, these are also evaluated with the meters. The test is completed by measuring the loss of pressure in Q3 flow if the hydrodynamic law which is described as "loss of pressure is proportional to the square ofis determined to be valid for the meter. The equipment is designed to be able to make the loss of pressure test of meters in acordance with related standarts info@euro-met.com.tr

4 WATER METER ENDURANCE (ABRASION) TESTING EQUIPMENT Aysu-Dayanıklılık (Aşındırma) Test Cihazı Endurance (Abrasion) Test Equipment Series: AYSU DT AYSU is a registered trademark and trademark assurance and manufactured with advanced technology and unique design according to OIML R49 and EN standards. All of the devices are traceable and it's calibration certified by ISO / IEC Water Meter Endurance (Abrasion) Test Bench TRADEMARK MODEL/TYPE EUROTEST AY40ET YEAR 2016 SERIAL NR It is a testing equipment for the test of continuous flow for 100 hours of the Q3 16m3/h meters in T30 and T50 Temperature Classes between DN 15-DN40 in Q4 Test Flow and 20 C Water Temperature Q3 TestFlow with interruptions as X15 seconds It is equipped with Electromagnetic Flow Meter that can show the Q3 and Q4 Test Flows momentarily in ó 02% Measurement Uncertanity Bidirectional Test Band (It is possible to test two different family group meters having equivalence Q3 flow) info@euro-met.com.tr 65

5 HEAT METER DURABILITY TEST EQUIPMENT Isı Sayaçları Dayanıklık(Aşındırma) Test Cihazı Heat meter DurabilityTest Equipment Series: AYSU HDT AYSU is a registered trademark and trademark assurance and manufactured with advanced technology and unique design according to OIML R75 and EN 1434 standards. All of the devices are traceable and it's calibration certified by ISO / IEC Heat Meter "Durability" Test and Calibration Bench TRADEMARK MODEL/TYPE EUROTEST-40HMD YEAR 2015 SERIAL NR ORIJIN TURKEY (1,5xqi) ± 5 %qp ± 5 % and qs 0-5 %; The basic wear test shall be carried out at the upper limit of the temperature range. After the test the error of indication shall be determined at the flow rates stated in of EN (for the flow sensor) at: For heating aplications (50±5) C or at ( max 0-5) C if max < 50 C. For cooling applications (15±5) C No significant error shall occur. Measurement Range 10 l/h~20m3/h Nominal Diameter DN15~Dn40 Air Temperature 20±5 C Relative Humidity 45~75%,rh 66 info@euro-met.com.tr

6 DOMESTIC WATER METER TEST AND CALIBRATION EQUIPMENT Domestic Water Meters Test and Calibration Bench In the scope of OIML R 49 and TS EN standards, water meters should operate truly in seven distinct flow intervals described below within the allowed error margins. Equipment to make these tests should have k=2ó 02% measurement uncertainty. Structural index error of the meters should be determined by comparing with the real volume in at least seven flows below and making examination in each flow for two times: Between Q1-1, Q1 Between 0,5(Q1 + Q2)-0,55(Q1 + Q2) (if Q2/Q1>1,6), Between Q2-1,1 Q2, Between 0,33(Q2 + Q3)-0,37(Q2 + Q3) Between 0,67(Q2 + Q3)-0,74(Q2 + Q3) Between 0,9 Q3 - Q3 Between 0,95 Q4 - Q4 info@euro-met.com.tr 67

7 WOLTMAN WATER METER TESTING EQUIPMENT AYSU WTB200 AYSU is a registered trademark and trademark assurance and manufactured with advanced technology and unique design according to OIML R49 and EN standards. All of the devices are traceable and it's calibration certified by ISO / IEC WOLTMAN WATER METER TEST AND CALIBRATION BENCH SPECIFICATION TRADEMARK MODEL/TYPE AYTEST-W300SE YEAR 2014 SERIAL NR. 2016W Nominal Diameter DN50~300 Test Line Capacity 1 to 3 Meter Test Line Sensitivity D5 Test Line Sensitivity U15 Minimum Flowrate, 100l/h Overload Flowrate, 1000 m 3 /h Referans Temperature 20 C Water Pressure Classes MAP16 In the scope of (MID) Council directive 2004/22/EC, OIML R 49 and TS EN standards, water meters should operate truly in seven distinct flow intervals described below within the allowed error margins. Equipment to make these tests should have k=2 0,2% measurement uncertainty. Structural index error of the meters should be determined by comparing with the real volume in at least seven flows below and making examination in each flow for two times: Between Q1-1,1 Q1, Between 0,5 (Q1 + Q2) -0,55 (Q1 + Q2) (if Q2/ Q1 > 1,6), Between Q2-1,1 Q2, Between 0,33 (Q2 + Q3)- 0,37 (Q2 + Q3), Between 0,67 (Q2 + Q3) -0,74 (Q2 + Q3), Between 0,9 Q3 - Q3, Between 0,95 Q4 - Q info@euro-met.com.tr

8 HEAT METER TEST AND CALIBRATION EQUIPMENT AYSU is a registered trademark and trademark assurance and manufactured with advanced technology and unique design according to 2014/32/ EU (MID), OIML R75 and EN 1434 standards. All of the devices are traceable and it's calibration certified by ISO / IEC Heat Meter Test and Calibration Bench In the scope of (MID) Council directive 2004/22/EC, OIML R 75 and EN 1434 standards, water meters should operate truly in seven distinct flow intervals described below within the allowed error margins. Equipment to make these tests should have k=2 0,2% measurement uncertainty. Structural index error of the meters should be determined by comparing with the real volume in at least seven flows below and making examination in each flow for two times: Complete meter The verification of the complete meter shall be carried out, at least within each of the following ranges For heating applications: a) Δ0min Δ 1,2 Δ0min and 0,9 qp q qp b) 10 K Δ 20 K and 0,1 qp q 0,11 qp c) Δ max - 5 K Δ Δ0max and qi q 1,1 qi SPECIFIC REQUIREMENTS Rated operating conditions The values of the rated operating conditions shall be specified by the manufacturer as follows: 1.1. For the temperature of the liquid: max, min, for the temperature differences: Δ max, Δ min, subject to the following restrictions: Δ max/δ min 10; Δ min = 3 K or 5 K or 10 K For the pressure of the liquid: The maximum positive internal pressure that the heat meter can withstand permanently at the upper limit of the temperature For the flow rates of the liquid: qs, qp, qi, where the values of qp and qi are subject to the following restriction: qp/qi For the thermal power: Ps. info@euro-met.com.tr 69

9 AYSU LABORATORY TEST EQUIPMENT AYSU LABORATORY TEST EQUIPMENT AYSU is a registered trademark and trademark assurance and manufactured with advanced technology and unique design according to OIML R49, 75 and R120; EN and EN 1434 standards. All of the devices are traceable and it's calibration certified by ISO / IEC *Domestic Water Meter Test and Calibration Bench *Woltman Water meter Test and Calibration Bench *Heat Meter Test and Calibration Bench *Test Measure for to Fuel Dispenser and Tanker Meter *Energy Meter Test Bench 70 info@euro-met.com.tr

10 AMR SYSTEM AND ALL PRODUCTS 71

11 Bu katalog kosgeb desteği ile basılmıştır. Basım Tarihi: 27 Nisan 2016 BETİMOFSET / studyo@superonline.com Ölçü Aletleri Lab. ve Test Ekip.Dan.İmalat San.Tic.Ltd.Şti. Anadolu Bulvarı ATB İş Merkezi C Blok No:84 Yenimahalle - Ankara / TÜRKİYE - 16 F: info@euro-met.com.tr