Piston Accumulators Series Catalog ontents

Transcription

1 atalog ontents Piston ccumulators Series 3000 Series 3000 Piston ccumulators Heavy uty Service with 3000 PSI Operating Pressure 2" thru 12" ores with Over 50 Standard apacities Patented V-O-ring Piston Seals Serviceable Threaded End onstruction Six Standard Seal Options to Handle a Variety of Fluids & Temperatures SME ertification vailable s 10 Parker Hannifin orporation ccumulator ivision

2 atalog /US Piston ccumulators Specifications Series 3000 Materials Shell high strength alloy steel (7" thru 12" bores comply with SME material specifications as standard) aps steel (7" thru 12" bores comply with SME material specifications as standard) Pistons aluminum (2" thru 7"), ductile iron (9" & 12") Gas Valve artridge stainless steel Gas Valve Protector steel Piston Glide Rings PTFE Piston & End Seals various polymers Piston Seal ackups PTFE ctual ore Sizes & Maximum Flow Rates Nominal ctual ore Size Max. Recommended Flow* ore Size (in.) (in.) (mm) GPM LPM *Note: ased on 120 in/sec maximum piston speed, port & fitting size will become limiting factors for most applications. Pressure Ratings Parker Series 3000 piston accumulators are rated at 3000 psi and a minimum 4 to 1 design factor. For pressures over 3000 psi, see Series 4000 and Series 5000 accumulators. Fluids Parker s piston accumulators are compatible with a wide variety of fluids. Standard accumulators (with nitrile seals) may be used with petroleum-based industrial oils or waterbased flame resistant fluids. Optional seals compatible with most industrial fluids are available with temperature ranges from -65 F to 400 F (-53 to 204 ). Precharge Units are shipped with a 25 psi nitrogen precharge as standard. For other precharge pressures, specify at the time of order. uxiliary Gas ottles When space does not permit the installation of the required piston accumulator, a smaller accumulator may be used by connecting it to an auxiliary gas bottle(s) that can be located in a nearby spot where space is available. In some cases, a piston accumulator and gas bottle combination may be more economical, especially large capacity sizes. Piston travel, confined to the accumulator, must be calculated with ample margins to store the required fluid. Standard s The following ports are supplied as standard on all fluid ends and on the gas end of accumulators ordered for use with gas bottles: Notes: 1) For flange dimensions, see tables below. 2) On standard 7" & 9" bore accumulators, both SE Straight Threadand Flange ports are available as standard. Omit port code for SE #32 Straight Thread, specify PL port code for 2" ode 61 Flange when ordering. Flange ports are recommended at operating pressures above 2000 PSI due to pressure limitations of most #32 SE Straight Thread fittings. Standard s Standard Models Metric Models ore SPP Metric SE Size SE SE Flange 1 (in) Flange 1 2 #12 3/4 3 # # #24 1-1/2 7 #32 2" ode 61 2" ode 61 9 #32 2" ode 61 2" ode " ode 61 3" ode 61 1) See flange dimensions in Options. vailable Options a wide variety of options are available on Parker s piston accumulators including: Seal ompounds s dapters Water Service Gas Valves Fuse Plugs ssemblies Fixed Gauge Mounts Piston Sensors (onsult Factory) ertifications Parker offers SME (Section VIII, iv. 1) and TÜV ertifications as standard options on piston accumulators and gas bottles as follows: ore SME TÜV Size Req'd. vailable (207 ar) 2" no no option 3" no no option 4", 6" no option option 7" yes option option 9", 12" yes option no See page 4 for a complete certification summary. s 11 Parker Hannifin orporation ccumulator ivision

3 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Small ore 3000 PSI Piston ccumulators for Oil and Water Service Threaded ored Gas Valve (See Note) Flanged Model No. 1 Fluid - Gas Oil Volume Volume S Tube E F G Weight Service (gal) (cu in) (cu in) (in) (in) (in) No. Size (in) Size (in) (in) (in) (lbs) 2N00051K N00 101K N00151K / / N00291K 1 Pint N00581K 1 Quart N00291K 1 Pint N00581K 1 Quart N00901K 1.5 Liter / /4 3/ N01 161K 1/2 Gal N0 1831K 3 Liter N00581K 1 Quart N01 161K 1/2 Gal N02311K 1 Gal / /4 1/ N03471K 1-1/2 Gal N05781K 2-1/2 Gal N02311K 1 Gal N03471K 1-1/2 Gal N05781K 2-1/2 Gal N09241K 4 Gal / /2 1/ N1 1551K 5 Gal N17331K 7-1/2 Gal N23 101K 10 Gal Notes: 1) For Water Service add W after construction code, see How to Order information. 2) See Options for complete listing of optional ports. 3) SME ertified accumulators and gas bottles are available. 4) TÜV ertification available on 3", 4", 6" and 7" bores. onsult factory for other sizes. 5) When accumulators are to be used with gas bottles, order Gas ottle ccumulators. 6) 2", 3", 4" & 6" bores standard with cored gas valves. Poppet type (military) gas valve available as an option. s 12 Parker Hannifin orporation ccumulator ivision

4 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Small ore 3000 PSI ccumulators for Use with Gas ottles Threaded Gas Flanged Fluid (oth Ends) Gas ccumulator Volume Volume S Tube E F G Weight Model No. (gal) (cu in) (cu in) (in) (in) No. Size (in) Size (in) (in) (in) (lbs) 4N00583KTFTF 1 Quart N01 163KTFTF 1/2 Gal N02313KTFTF 1 Gal / /4 1/ N03473KTFTF 1-1/2 Gal N05783KTFTF 2-1/2 Gal N02313KTGTG 1 Gal N03473KTGTG 1-1/2 Gal N05783KTGTG 2-1/2 Gal N09243KTGTG 4 Gal / /2 1/ N1 1553KTGTG 5 Gal N17333KTGTG 7-1/2 Gal N23103KTGTG 10 Gal PSI uxiliary Gas ottles ored Gas Valve (See Note) Threaded Flanged Model No. Gas Volume Gas Nominal ctual S Tube E F G Weight ottle (gal) (cu in) (in) (in) (in) No. Size (in) Size (in) (in) (in) (lbs) 4N00581K 1 Quart N01161K 1/2 Gal N02311K 1 Gal / /4 1/ N03471K 1-1/2 Gal N05781K 2-1/2 Gal N02311K 1 Gal N03471K 1-1/2 Gal N05781K 2-1/2 Gal N09241K 4 Gal / /2 1/ N1 1551K 5 Gal N17331K 7-1/2 Gal N23 101K 10 Gal s 13 Parker Hannifin orporation ccumulator ivision

5 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Small ore 207 ar Metric ccumulators for Oil and Water Service Threaded ored Gas Valve (See Note) Flanged Model No. 1 Fluid Gas - Volume Oil Volume SPP/G SE E F G Weight Service (Liters) (cu in) (Liters) (mm) (mm) (mm) (in) Flange (mm) (mm) (mm) (Kg) 2N00052K N00 102K N00152K / N00292K N00582K N00292K N00582K N00902K M N01 162K N01832K N00582K N01 162K N02312K M N03472K N05782K N02312K N03472K N05782K N09242K /2 M N1 1552K N1 7332K N23 102K Notes: 1) For Water Service add W after construction code, see How to Order information. 2) See Options for complete listing of port options. 3) SME ertified accumulators and gas bottles are available. 4) TÜV ertification available on 3", 4", 6" and 7" bores. onsult factory for other sizes. 5) When accumulators are to be used with gas bottles, order Gas ottle ccumulators. 6) 2", 3", 4" & 6" bores standard with cored gas valves. Poppet type (military) gas valves available as an option. s 14 Parker Hannifin orporation ccumulator ivision

6 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Small ore 207 ar Metric ccumulators for Use with Gas ottles Gas Threaded Flanged Fluid - Gas ccumulator Volume Volume SPP/G SE E F G Weight Model No. (Liters) (cu in) (Liters) (mm) (mm) (in) Flange (mm) (mm) (mm) (Kg) 4N00582KRR N01 162KRR N02312KRR M N03472KRR N05782KRR N02312KRFRF N03472KRFRF N05782KRFRF N09242KRFRF /2 M N1 1552KRFRF N KRFRF N23 102KRFRF ar Metric uxiliary Gas ottles ored Gas Valve (See Note) Threaded Flanged Model No. Gas Volume - Gas Nominal ctual SPP/G SE E F G Weight ottle (gal) (liters) (mm) (mm) (mm) (in) Flange (mm) (mm) (mm) (Kg) 4N00582K 1 Quart N01 162K 1/2 Gal N02312K 1 Gal M N03472K 1-1/2 Gal N05782K 2-1/2 Gal N02312K 1 Gal N03472K 1-1/2 Gal N05782K 2-1/2 Gal N09242K 4 Gal /2 M N1 1552K 5 Gal N 17332K 7-1/2 Gal N23 102K 10 Gal s 15 Parker Hannifin orporation ccumulator ivision

7 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Large ore 3000 PSI Piston ccumulators for Oil and Water Service High Pressure MS Gas Valve Flanged Model No. 1 Fluid - Gas Oil Volume Volume S Tube E F G Weight Service (gal) (cu in) (cu in) (in) (in) (in) No. Size (in) Size (in) (in) (in) (lbs) 7K05783K(PL) 2-1/2 Gal / K1 1553K(PL) 5 Gal K17333K(PL) 7-1/2 Gal or 5/ K23103K(PL) 10 Gal ± ode K34653K(PL) 15 Gal Flange (PL) K57753K(PL) 25 Gal K23 103K(PL) 10 Gal / K34653K(PL) 15 Gal K46203K(PL) 20 Gal or 3/ K57753K(PL) 25 Gal ± ode K69303K(PL) 30 Gal Flange (PL) K57751K 12K69301K 12K92401K 12K115501K 25 Gal. 30 Gal. 40 Gal. 50 Gal ± " SE Flange s (ode 61) See Options for imensions 7/8-9 (6X) The Minimum esign Metal Temperature (MMT) for SME certified 7 and 9 piston accumulators presented in this section is 20 F (-7 ). The Minimum esign Metal Temperature (MMT) for SME certified 12 piston accumulators presented in this section is 32 F (0 ). Notes: 1) For Water Service add W after construction code, see How to Order information. 2) Most SE #32 fittings are rated for 2000 PSI. If 2000 to 3000 PSI service is required, two options are available; order accumulator with optional standard 2" SE ode 61 4-bolt flange port by specifying PL code when ordering or order the accumulator with a SE #24 port or smaller, see Options for dimensions and How to Order. 3) See Options for complete listing of optional ports. 4) SME ertified accumulators and gas bottles are available. 5) TÜV ertification available on 7" bores. onsult factory for other sizes. 6) When accumulators are to be used with gas bottles, order Gas ottle ccumulators. 7) Poppet type (military) gas valve standard. s 16 Parker Hannifin orporation ccumulator ivision

8 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Large ore 3000 PSI ccumulators for Use with Gas ottles Flanged Fluid Gas ccumulator Volume Volume E F G Weight Model No. (gal) (cu in) (cu in) (in) (in) (oth Ends) (in) (in) (in) (lbs) 7K05781K(PLPL) 2-1/2 Gal K1 1551K(PLPL) 5 Gal " ode 61 Flange (PL) K17331K(PLPL) 7-1/2 Gal or 5/ K23101K(PLPL) 10 Gal ± #32 SE Straight Thread 374 7K34651K(PLPL) 15 Gal K23101K(PLPL) 10 Gal K34651K(PLPL) 15 Gal " ode 61 Flange (PL) K46201K(PLPL) 20 Gal or 3/ K57751K(PLPL) 25 Gal ± #32 SE Straight Thread 926 9K69301K(PLPL) 30 Gal K57753KPNPN 25 Gal " SE Flange K69303KPNPN 30 Gal s (ode 61) / K92403KPNPN 40 Gal ± See Options 1793 (6X) 12K KPNPN 50 Gal for imensions PSI uxiliary Gas ottles High Pressure MS Gas Valve Flanged Model No. Gas Volume Gas Nominal ctual E F G Weight ottle (gal) (cu in) (in) (in) (in) (in) (in) (in) (lbs) 7K05783K(PL) 2-1/2 Gal K11553K(PL) 5 Gal " ode 61 Flange (PL) K17333K(PL) 7-1/2 Gal or 5/ K23103K(PL) 10 Gal ± #32 SE Straight Thread 356 7K34653K(PL) 15 Gal K23103K(PL) 10 Gal K34653K(PL) 15 Gal " ode 61 Flange (PL) K46203K(PL) 20 Gal or 3/ K57753K(PL) 25 Gal ± #32 SE Straight Thread 900 9K69303K(PL) 30 Gal K57751K 25 Gal " SE Flange K69301K 30 Gal s (ode 61) 7/ K92401K 40 Gal ± See Options (6X) K115501K 50 Gal for imensions 1650 s 17 Parker Hannifin orporation ccumulator ivision

9 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Large ore 207 ar Metric ccumulators for Oil and Water Service High Pressure MS Gas Valve Flanged Model No. 1 Fluid Gas - Oil Volume Volume SPP/G SE E F G Weight Service (Liters) (cu in) (Liters) (mm) (mm) (mm) (in) Flange (mm) (mm) (mm) (Kg) 7K05782K K1 1552K " Metric 112 7K1 7332K ode 61 M K23 102K ± Flange 170 7K34652K K23 102K K34652K "Metric 293 9K46202K ode 61 M K57752K ± Flange 421 9K6 9302K K57752K " Metric 12K69302K M ode K92402K ± (6X) 813 Flange 12K K Notes: 1) For Water Service add W after construction code, see How to Order information. 2) See Options for complete listing of port options. 3) SME ertified accumulators and gas bottles are available. ll 7", 9" and 12" bores in this section comply with SME material specifications as standard. 4) TÜV ertification available on 7" bores. onsult factory for other sizes. 5) When accumulators are to be used with gas bottles, order Gas ottle ccumulators, see next page. 6) Poppet type (military) gas valve standard. s 18 Parker Hannifin orporation ccumulator ivision

10 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Large ore 207 ar Metric ccumulators for Use with Gas ottles Flanged Fluid - Gas ccumulator Volume Volume SPP/G SE E F G Weight Model No. (Liters) (cu in) (Liters) (mm) (mm) (in) Flange (mm) (mm) (mm) (Kg) 7K05782KMLML K1 1552KMLML " Metric 112 7K 17332KMLML ode 61 M K23 102KMLML ± Flange 170 7K34652KMLML K23 102KMLML K34652KMLML " Metric 293 9K46202KMLML ode 61 M K34652KMLML ± Flange 420 9K46202KMLML K57752KMNMN " Metric 12K69302KMNMN M ode K92402KMNMN ± Flange (6X) K KMNMN ar Metric uxiliary Gas ottles High Pressure MS Gas Valve Flanged Model No. Gas Volume - Gas Nominal ctual SPP/G SE E F G Weight ottle (gal) (liters) (mm) (mm) (mm) (in) Flange (mm) (mm) (mm) (Kg) 7K05782K 2-1/2 Gal K1 1552K 5 Gal " Metric 112 7K 17332K 7-1/2 Gal ode 61 M K23102K 10 Gal ± Flange 170 7K34652K 15 Gal K23102K 10 Gal K34652K 15 Gal " Metric 293 9K46202K 20 Gal ode 61 M K57752K 25 Gal ± Flange 420 9K34652K 30 Gal K57752K 25 Gal " Metric 12K69302K 30 Gal M ode K92402K 40 Gal. 160 ± (6X) 813 Flange 12K115502K 50 Gal s 19 Parker Hannifin orporation ccumulator ivision

11 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Non-SME 7 ore 3000 PSI Non-SME Piston ccumulators for Oil and Water Service SME certification is a requirement of strength and material traceability (see page 4). Many states require SME certification, but not all. It is the function of the system designer to specify whether SME is or is not required. We now offer true non-sme accumulators in 7 bore size which carry a full 4:1 design factor and utilize industry standard materials. When SME certification is not required, specifying these accumulators can result in significant savings. Local rules and regulations should be followed. However, the accumulators listed on these two pages can be used with confidence when SME certification is not required. High Pressure MS Gas Valve Flanged Model No. 1 Fluid - Gas Oil Volume Volume S Tube E F G Weight Service (gal) (cu in) (cu in) (in) (in) (in) No. Size (in) Size (in) (in) (in) (lbs) 7N05783K(PL) 2½ / N1 1553K(PL) N17333K(PL) 7½ or 5/ N23103K(PL) ode N34653K(PL) Flange (PL) N57753K(PL) Notes: 1) For Water Service add W after construction code, see How to Order information. 2) Most SE #32 fittings are rated for 2000 PSI. If 2000 to 3000 PSI service is required, two options are available; order accumulator with optional standard 2" SE ode 61 4-bolt flange port by specifying PL code when ordering or order the accumulator with a SE #24 port or smaller, see Options for dimensions and How to Order. 3) See Options for complete listing of optional ports. 4) SME ertified accumulators and gas bottles are available. 5) TÜV ertification available on 7" bores. onsult factory for other sizes. 6) When accumulators are to be used with gas bottles, order Gas ottle ccumulators. 7) Poppet type (military) gas valve standard. s 20 Parker Hannifin orporation ccumulator ivision

12 atalog /US Models, apacities and imensions Piston ccumulators Series 3000 Non-SME 7 ore 3000 PSI Non-SME ccumulators for Use with Gas ottles Flanged Fluid Gas ccumulator Volume Volume E F G Weight Model No. (gal) (cu in) (cu in) (in) (in) (oth Ends) (in) (in) (in) (lbs) 7N05783K(PLPL) 2½ N1 1553K(PLPL) " ode 61 Flange (PL) N 17333K(PLPL) 7½ or 5/ N23 103K(PLPL) #32 SE Straight Thread 377 7N34653K(PLPL) N57753K(PLPL) PSI Non-SME uxiliary Gas ottles High Pressure MS Gas Valve Flanged Model No. Gas Volume Gas Nominal ctual E F G Weight ottle (gal) (cu in) (in) (in) (in) (in) (in) (in) (lbs) 7N05783K(PL) 2½ N11553K(PL) " ode 61 Flange (PL) N17333K(PL) 7½ or 5/ N23103K(PL) #32 SE Straight Thread 368 7N34653K(PL) N57753K(PL) s 21 Parker Hannifin orporation ccumulator ivision

13 atalog /US Models, apacities and imensions Piston ccumulators Series 2000 PSI PSI Piston ccumulators for Oil and Water Service The aluminum die casting industry has been the primary user of our 2000 PSI accumulators. We offer a 2000 PSI accumulator in 12 bore size and a variety of capacities for industries where lower pressure ratings can be used. High Pressure MS Gas Valve Flanged Model No. 1 Fluid - Gas Oil Volume Volume S Tube E F G Weight Service (gal) (cu in) (cu in) (in) (in) (in) No. Size (in) Size (in) (in) (in) (lbs) 12K4620K1K " SE Flange 12K5775K1K s (ode 61) 12K6930K1K / See Options 12K9240K1K ± (6X) 1325 for imensions 12K1 1550K1K Notes: 1) For Water Service add W after construction code, see How to Order information. 2) See Options for complete listing of optional ports. 3) SME ertified accumulators and gas bottles are available. The units in this section comply with SME material specifications as standard. 4) TÜV ertification available on 7" bores. onsult factory for other sizes. 5) When accumulators are to be used with gas bottles, order Gas ottle ccumulators. 6) Poppet type (military) gas valve standard. s 22 Parker Hannifin orporation ccumulator ivision

14 atalog /US Models, apacities and imensions Piston ccumulators Series 2000 PSI PSI ccumulators for Use with Gas ottles Flanged Fluid Gas ccumulator Volume Volume E F G Weight Model No. (gal) (cu in) (cu in) (in) (in) (oth Ends) (in) (in) (in) (lbs) 12K4620K3KPNPN " SE Flange 12K5775K3KPNPN s (ode 61) 12K6930K3KPNPN / See Options 12K9240K3KPNPN ± (6X) 1325 for imensions 12K1 1550K3KPNPN PSI uxiliary Gas ottles High Pressure MS Gas Valve Flanged Model No. Gas Volume Gas Nominal ctual E F G Weight ottle (gal) (cu in) (in) (in) (in) (in) (in) (in) (lbs) 12K4620K1K " SE Flange K5775K1K s (ode 61) 7/ K6930K1K See Options K9240K1K ± (6X) for imensions K11550K1K s 23 Parker Hannifin orporation ccumulator ivision

15 atalog /US Options and Seal Kits Piston ccumulators Series 3000 Water Service Option (W) Piston accumulators are available for use with water as the fluid media. Modifications include electroless nickel plating all surfaces and metal parts. arboxilated Nitrile (J) piston seals should be specified for water service. onsult factory for details. Seals **Recommended Maximum Seal Operating Temperature with General pplication ode Polymer Temperature Range Reduced Life and ompatibility* K E H J Q una- -20 F to 165 F 200 F Parker's Standard ompound ompatible Nitrile -29 to with most mineral oil-based fluids Fluorocarbon -10 F to 250 F 400 F ompatible with most mineral oil-based fluids at Elastomer -23 to higher temperatures and some exotic fluids Ethylene -40 F to 250 F 300 F ompatible with most phosphate ester fluids Propylene -40 to and some synthetic fluids Hydrogenated - 45 F to 325 F 350 F ompatible with most oil-based and biodegradable fluids, Nitrile -43 to maintains sealing effectiveness at low temperatures arboxilated -20 F to 165 F 200 F ompatible with most mineral oil-based fluids Nitrile -29 to with added internal lubricity for water based fluids Low Temp. -45 F to 160 F 200 F ompatible with most mineral oil-based fluids and Nitrile -43 to maintains sealing effectiveness at low temperatures *Note: onsult local distributor or factory for fluid compatibility information. Temperature ranges may vary depending upon fluid used in hydraulic system. ** The temperatures listed indicate the operating temperature range of the seals, not the accumulator. For the Minimum esign Metal Temperature (MMT) of SME certified accumulators, refer to page 16. Seal Kits Seal Kits are available for all piston accumulator models. When ordering seal kits, please supply the complete model and serial numbers from the name plate and specify fluid type and operating temperature. Parts List 1 ody 7 O-ring 2 ap 7 O-ring ackup 3 Gas ap 8 Gas Valve 4 Piston 8 Gas Valve O-ring 5 V-O-ring Piston Seal 9 Gas Valve Guard 5 V-O-ring ackups 9 Screw 6 PTFE Glide Rings PSI Seal Kit Numbers (Includes items 5, 5, 6, 7, 7, 8) Material ore Size 2" 3" 4" 6" una-nitrile (Std.) RK0200K000 RK0300K000 RK0400K000 RK0600K000 RK0700K000 RK0900K000 RK1200K000 Fluorocarbon RK0200E000 RK0300E000 RK0400E000 RK0600E000 RK0700E000 RK0900E000 RK1200E000 EPR RK RK RK RK RK RK F* Hydrogenated Nitrile RK0200H000 RK0300H000 RK0400H000 RK0600H000 RK0700H000 F* F* arboxylated Nitrile RK0200J000 RK0300J000 RK0400J000 RK0600J000 RK0700J000 RK0900J000 F* Low Temp Nitrile RK0200Q000 RK0300Q000 RK0400Q000 RK0600Q000 RK0700Q000 RK0900Q000 F* *onsult Factory s 24 Parker Hannifin orporation ccumulator ivision

16 atalog /US Options Piston ccumulators Series 3000 Optional s The following ports are available as options on all piston accumulators (note standard ports above). SE Straight Thd. ode 61 Flange ode 62 Flange NPT SPP ISO Min. ode Min. ode Min. Min. Min. Min. Size ode ore Size Inch Metric ore Size Inch Metric ore Size ode ore Size ode ore Size ode ore #5 T 2" 1/2" PT MT 3" 1" PG MG 4" 3/8" UT 2" 3/8" R 2" M14 Y 2" #6 T 2" 3/4" PU MU 3" 1¼" PH MH 4" 1/2" UU 2" 1/2" R 2" M18 Y 2" #8 T 2" 1" PV MV 3" 1½" PP MP 6" 3/4" UV 2" 3/4" R 2" M22 Y 2" #10 TI 2" 1-1/4" PW MW 3" 2" PQ MQ 6" 1" UW 3" 1" R 3" M27 Y 2" #12 T 2" 1-1/2" PJ MJ 4" 2½" PR 7" 1¼" UX 3" 1¼" RE 3" M33 YE 3" #16 TE 3" 2" PL ML 6" 3" PS 9" 1½" UY 4" 1½" RF 4" M42 YF 3" #20 TF 3" 2-1/2" PM MM 6" 2" UZ 4" 2" RG 4" #24 TG 4" 3" PN MN 7" Note: 1) 3000 PSI SE ode 61 (ISO 6162) Flange dimensions are shown below. 2) 1" thru 2" flanges are to standard SE ode 62 dimensions, 2-1/2" & 3" to Socket Weld Flange dapter Pattern, dimensions are shown below. Metric pattern supplied on 207 ar Metric units unless otherwise specified. 3) SPT and Metric ports available, consult factory. SE 4-olt Flange imensions Standard Pressure SE ode 61 (ISO 6162) 3000 PSI (207 ar) Flange Size SE Flange imensions (in.) Metric SE Flange imensions (mm) in mm F G F G 1½" 38 1/ ½ M " 51 1/ M ½" 64 1/ ½ M " 76 5/ M Note: Some flanges using this bolt pattern are not rated for 3000 PSI. F High Pressure ode 62 (ISO 6162) (thru 2" diameter) 6000 PSI (410 ar) Flange Size SE Flange imensions (in.) Metric SE Flange imensions (mm) in mm F G F G 1½" 38 5/ ½ M " 50 3/ M ½" 7/ ½ " 1-1/ Note: Some flanges using this bolt pattern are not rated for 6000 PSI. 1-1/2" & 2" flanges are to standard SE ode 62 dimensions, 2-1/2" & 3" to Socket Weld Flange dapter Pattern. (4 places) x G Min. epth dapters wide variety of port adapters are offered for those that wish to convert Parker s standard SE port offerings to NPTF or smaller SE port sizes. For a complete listing, see ccumulator ccessories. s 25 Parker Hannifin orporation ccumulator ivision

17 atalog /US Options and ccessories Piston ccumulators Series 3000 Gas Valve Option (M) Two types of gas valves are available on Series 3000 piston accumulators and gas bottles. Units with 2" thru 6" bores, are offered with a cored gas valve cartridge (ISO V1) as standard. ll 7" thru 12" bore units are supplied with a heavy duty (military) poppet-type gas valve cartridge (Mil. Spec. MS ) as standard. The military style (MS) gas valve is available on 2" thru 6" bores as an option (M), specify when ordering. Standard Gas Valve #5 SE Thread Military Gas Valve 1/2-20 UNF-2 Safety Fuse Options (F) Safety Fuses are used as a safety device on accumulators and gas bottles to prevent over-pressurization of gas due to external heat or hydraulic pressure (set at 140% of maximum system pressure to avoid rupture disk fatigue and premature failure). The rupture disks are calibrated to rupture at a predetermined pressure. Safety fuses are available on most sizes of piston and bladder accumulators and gas bottles. Safety fuses can be installed on all piston accumulators by using the Fuse dapter as shown to the right. 4" bore units and above can be equipped with a fuse port machined in the gas cap by specifying the Safety Fuse Option (F) at the time of order in the model code, see How to Order. The safety fuse assembly and/or fuse adapter must be ordered separately. escription Part Number Safety Fuse ssembly xxxx Replacement Rupture isks xxxx Fuse dapter ) ssembly includes housing and rupture disk, xxxx = pressure setting in 100 psi increments, i.e., for an assembly with a 2000 PSI setting, order P/N Fuse Fuse dapter #8 SE Straight Thread #5 SE Straight Thread #5 SE Straight Thread Mounting, harging & Gauging ccessories Parker offers a wide variety of mounting, charging and gauging accessories. See ccumulator ccessories. Special Options If your application requires a piston accumulator, gas bottle, or special option that falls outside of Parker s broad offering, consult your local distributor, Parker representative, or the factory with your specific requirements. Parker has the manufacturing and engineering expertise to design and build piston accumulators to your exacting requirements, from simple modifications of standard units to complete designs. Some example of Parker s past special designs include: Special and Stainless Steel Materials Piston Position and Velocity Sensors and Switches Special Seals Non-Standard apacities Tie Rod onstruction Special ertifications Spring & Weight Loaded onsult the experts at Parker with your next piston accumulator requirement! s 26 Parker Hannifin orporation ccumulator ivision

18 atalog /US Ordering Information Piston ccumulators Series 3000 How to Order Piston ccumulators Piston accumulators and gas bottles can be specified by using the symbols in the chart below to develop a model number. Select only those symbols that represent the features desired, and place them in the sequence indicated by the example at the top of the chart. Nominal ore Type of esign esign Seal Hyd. Gas Series Size onstruction Options apacity Pressure Number ompound Modification Modification 7 K K Series ccumulator Gas ottle Nominal ore Size 2 2 inches 3 3 inches 4 4 inches 6 6 inches 7 7 inches 9 9 inches inches N K L T Type of onstruction Threaded both ends non-sme mat l standard on 2, 4, 6 (3000 PSI fatigue design tested) Threaded both ends.s.m.e. mat l standard on 7 & up Same as K with.s.m.e. approval stamp 7 & up. vailable as special on smaller sizes Threaded both ends TÜV approved 3, 4, 6 & 7 bores only Options lank Standard Gas ap W Water Service F SE Fuse * G SE Fuse * Water Service M 5,000 PSI Gas Valve L 5,000 PSI Gas Valve Water Service P Fuse and MS Valve R Fuse and MS Valve Water Service * Safety fuse assembly not included. Order fuse assembly separately. ore Size/apacity cu. in cu. in cu. in cu. in cu. in cu. in cu. in cu. in cu. in cu. in cu. in gal ½ gal ½ gal gal ½ gal ½ gal gal gal ½ gal gal ½ gal gal ½ gal gal gal gal gal gal gal gal gal gal gal gal gal. onsult factory for other available sizes. K X esign Pressure 3000 PSI (ll ore Sizes) 2000 PSI Special Other esign Number 1 Standard* 2 Metric Mounting Holes & Hyd. (SPP Standard*) Specify Special s 3 Special (Hyd. or Gas, See Table) ### Special esign and Gas Modifications esignated by 2 igits 1st 2nd Min. igit Style igit escription ore Size lank Std. lank Std. Straight Thread s T SE SE #5 (1/2-20) 2 SE #6 (9/16-18) 2 SE #8 (3/4-16) 2 SE #12 (1 1/16-12) 2 E SE #16 (1 5/16-12) 3 F SE #20 (1 5/8-12) 3 G SE #24 (1 7/8-12) 4 H SE #32 (2 1/2-12) 7 I SE #10 (7/8-14) PSI (ode 61) 6000 PSI (ode 62) Min. ore Min. ore P Flange J 1 1/2 4 G 1 4 L 2 6 H 1 1/4 4 M 2 1/2 6 P 1 1/2 6 M Metric N 3 7 Q 2 6 Flange T 1/2 3 R* 2 1/2 7 per U 3/4 3 S* 3 9 ISO 6162 V 1 3 * For socket weld flange. Not W 1 1/4 3 available with metric flange. T 3/8 2 U NPTF U 1/2 2 (Not V 3/4 2 Recommended) W 1 2 X 1 1/4 2 Y 1 1/2 4 Z 2 4 SPP/SPT Metric/ISO R SPP 3/8-19 M14 x 1.5 Parallel 1/2-14 M18 x 1.5 SPT 3/4-14 M22 x 1.5 Taper 1-11 M27 x 2 G Metric E 1 1/4-11 E M33 x 2 Y ISO F 1 1/2-11 F M42 x G 2-11 G M48 x 2 Example of Special ccumulator 4 N K T U V Non-std. *Standard s vailable (See Modifications Table if Using Other Than Standard s Shown elow) ore Standard Metric Size Sizes Sizes 2 SE #12 3/4 3 SE#12 3/4 4 SE # SE # SE #32 2 ode 61 9 SE #32 2 ode SE Flange 3 ode 61 ode 61 SE #8 Hyd. Seal ompound (See atalog for Temperature Settings) K una-nitrile (Std) E Fluoroelastomer EPR H Hydrogenated Nitrile J HWF Q S NPT 3/4 Gas Low Temp. Special (to be specified) s 27 Parker Hannifin orporation ccumulator ivision