INSTALLATION INSTRUCTIONS: SCTB1600
|
|
- Ada Hunter
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS: SCTB1600 DESCRIPTION: BOLLARD, 1600 DWG: INSTALL_SCTB1600 REV: M01 BASE TYPE B1 DIRECT BURIAL - PG. 6: BOLLARD IS PERMANENT, IT IS DIRECTLY BURIED INTO CONCRETE BASE TYPE B2 BASE TYPE B3 THREADED ROD - PG. 7: THREADED ANCHOR - PG. 9: BOLLARD IS REMOVABLE, A THREADED ROD IS PERMANENTLY SET INTO CONCRETE & PROTRUDES ABOVE GROUND SURFACE WHEN BOLLARD IS REMOVED. BOLLARD IS REMOVABLE, AN ANCHOR IS SET PERMANENTLY INTO CONCRETE & FLUSH WITH THE SURFACE WHEN BOLLARD IS REMOVED. BASE TYPE B3/4 THREADED ANCHOR - PG. 11: BOLLARD IS REMOVABLE, AN ANCHOR IS SET PERMANENTLY INTO CONCRETE FLUSH WITH SURFACE. BOLLARD SLIDES OVER SLEEVE & HELD WITH PIN. BASE TYPE B4 REMOVABLE FROM SLEEVE - PG. 13: BOLLARD IS REMOVABLE, POST IS SET PERMANENTLY INTO CONCRETE & PROTRUDES FROM SURFACE. BOLLARD SLIDES OVER POST & IS HELD IN PLACE WITH A PIN 1
2 NOTES:!CAUTION! FAILURE TO FOLLOW INSTRUCTIONS COULD LEAD TO INJURY, ENSURE ALL STEPS ARE FOLLOWED AND FASTENERS ARE USED, TWO OR MORE PEOPLE ARE REQUIRED FOR INSTALLATION!CAUTION! PLEASE ENSURE THAT THE ANCHORS BEING USED FOR THIS PRODUCT HAVE ADEQUATE CAPACITY FOR SECURING THE PRODUCT AS INTENDED. IN ORDER FOR ANCHORS TO MEET THEIR CATALOGUE RATINGS, THEY MUST BE INSTALLED IN SOLID CONCRETE AND AS PER ANCHOR MANUFACTURERS SPECIFICATIONS. TOOLS (NOT SUPPLIED): WRENCH 1 1/8" RATCHET WRENCH 1 1/8" HEX KEY OR ALLEN KEY 3/16" & 3/8" HAMMER DRILL (MASON BIT SIZE THAT MATCHES CHOSEN ANCHOR) THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED. 2
3 PARTS: ANCHOR SUPPLIED WITH BASE TYPE B3 & B3/4 1 3/4" 44mm 8 1/2" 216mm 1 1/8" 29mm 3
4 PARTS: PIN SUPPLIED WITH BASE TYPE 3/4 & 4 3/8" 10mm FOR PAD LOCK 1" 25mm 7 9/16" 192mm 1/2" 13mm 4
5 PARTS: THREADED ROD SUPPLIED WITH BASE TYPE 2 9" 229mm 5
6 BASE TYPE B1 SET THE BOLLARD IN WET CONCRETE KEEPING BOTTOM EDGE (POINT A) EVEN WITH FINISH 1 GRADE, ALSO SET THE BOLLARD TO DESIRED ORIENTATION. 2 INSTALLATION IS COMPLETE NOW. ENSURE THAT THE BOLLARD IS SUPPORTED IN A PLUMB POSITION AS CONCRETE HARDENS. POINT A CONCRETE EXTRUSION IS EXTENDED 18" BELOW GRADE 6
7 BASE TYPE B2 1 FOR NEW CONCRETE BASE :-PLACE ROD 3" ABOVE GROUND INTO CONCRETE, ENSURE THAT THE THREADED ROD IS SUPPORTED IN A PLUMB POSITION UNTIL ROD IS SET. FOR AN EXISTING CONCRETE BASE :- DRILL 1" HOLE INTO THE PAD & EPOXY THE THREADED ROD IN PLACE SITTING 3" ABOVE GROUND SO THAT IT WILL NOT ROTATE. ENSURE THAT THE THREADED ROD IS SUPPORTED IN A PLUMB POSITION UNTIL ROD IS SET. 2 ONCE THE ROD IS SET, PLACE ABS DISK ON BOTTOM AS SHOWN. FASTEN THE BASE PLATE TO THREADED ROD IN DESIRED ORIENTATION ON TOP OF ABS DISK. NOTE THAT THE HOLES NEED TO ALIGN WITH 4 HOLES ON THE BOLLARD BASE (POINT B). THIS DETERMINES THE FINAL INSTALLED ORIENTATION OF THE BOLLARD 3" 78mm!CAUTION! - KEEP THREADED ROD CLEAN OF CONCRETE OR EPOXY DURING INSTALL. NUT LOCK WASHER & WASHER BASE PLATE 6" 152mm FOR REF. ABS DISK THREADED ROD DETAIL CONCRETE DETAIL A SCALE 1 : 6 POINT B 7
8 PLACE BOLLARD ON BASE MOUNT IN DESIRED ORIENTATION, FASTEN EQUALLY FROM ALL 4 3 SIDES TO SECURE THE BOLLARD USING HEX KEY (POINT C). 4 INSTALLATION IS COMPLETE NOW POINT C 8
9 BASE TYPE B3 1 FOR NEW CONCRETE BASE :- PLACE THREADED ANCHOR FLUSHED TO GROUND INTO CONCRETE, ENSURE THAT THE THREADED ANCHOR IS SUPPORTED IN A PLUMB POSITION UNTIL ANCHOR IS SET. FOR AN EXISTING CONCRETE BASE :- DRILL 2" HOLE INTO THE PAD, PLACE ANCHOR INTO GROUND FLUSH WITH GRADE THEN POUR CONCRETE. ENSURE THAT THE THREADED ROD IS SUPPORTED IN A PLUMB POSITION UNTIL ROD IS SET. NOTE - WHEN BOLLARD IS REMOVED THE PLUG MUST BE PLACED BACK INTO ANCHOR HOLE TO PREVENT DIRT AND DERBIS FROM ENTERING (POINT D). 2 ONCE THE ANCHOR IS SET, PLACE ABS DISK ON BOTTOM AS SHOWN. FASTEN THE BASE PLATE TO ANCHOR IN DESIRED ORIENTATION ON TOP OF ABS DISK. NOTE THAT THE HOLES NEED TO ALIGN WITH 4 HOLES ON THE BOLLARD BASE (POINT E). THIS DETERMINES THE FINAL INSTALLED ORIENTATION OF THE BOLLARD SCREW LOCK WASHER & WASHER BASE PLATE ABS DISK PLUG POINT D ANCHOR DETAIL D SCALE 1 : 2 CONCRETE DETAIL B SCALE 1 : 6 POINT E 9
10 PLACE BOLLARD ON BASE MOUNT IN DESIRED ORIENTATION, FASTEN EQUALLY FROM ALL 4 3 SIDES TO SECURE THE BOLLARD USING HEX KEY (POINT F). 4 INSTALLATION IS COMPLETE NOW POINT F 10
11 BASE TYPE B3/4 1 2 FOR NEW CONCRETE BASE :- PLACE THREADED ANCHOR FLUSHED TO GROUND INTO CONCRETE, ENSURE THAT THE THREADED ANCHOR IS SUPPORTED IN A PLUMB POSITION UNTIL ANCHOR IS SET. FOR AN EXISTING CONCRETE BASE :- DRILL 2" HOLE INTO THE PAD, PLACE ANCHOR INTO GROUND FLUSH WITH GRADE THEN POUR CONCRETE. ENSURE THAT THE THREADED ROD IS SUPPORTED IN A PLUMB POSITION UNTIL ROD IS SET. NOTE - WHEN BOLLARD IS REMOVED THE PLUG MUST BE PLACED BACK INTO ANCHOR HOLE TO PREVENT DIRT AND DERBIS FROM ENTERING (POINT G). ONCE THE ROD IS SET, PLACE ABS DISK ON BOTTOM FASTEN THE SLEEVE TO ANCHOR IN DESIRED ORIENTATION ON TOP OF ABS DISK. NOTE THAT THE HOLES NEED TO ALIGN WITH 4 HOLES ON THE BOLLARD BASE (POINT H). THIS DETERMINES THE FINAL INSTALLED ORIENTATION OF THE BOLLARD SCREW LOCK WASHER & WASHER SLEEVE PLUG POINT G ABS DISK ANCHOR DETAIL E SCALE 1 : 2 CONCRETE CONCRETE DETAIL C SCALE 1 : 6 POINT H 11
12 3 4 ORIENT THE BOLLARD WITH BOTTOM SLEEVE & SLIDE IT ON. SECURE USING PIN (POINT I ) USE PAD LOCK IF NEEDED. INSTALLATION IS COMPLETE NOW. POINT I 12
13 BASE TYPE B4 1 2 SET THE DIRECT BURIAL POST IN WET CONCRETE KEEP TUBE EDGE 6-1/16" ABOVE GRADE, ENSURE HOLE IS 5-1/16" ABOVE GRADE. SET THE DESIRED ORIENTATION & CONFIRM THAT BOLLARD PIN CAN SLIDE INTO PLACE. ENSURE THAT THE DIRECT BURIAL POST IS SUPPORTED IN A PLUMB POSITION AS CONCRETE HARDENS. ONCE THE POST IS SET, PLACE ABS DISK ON BOTTOM AS SHOWN. ORIENT THE BOLLARD WITH POST & SLIDE IT ON. SECURE USING PIN AT THE BOTTOM. USE PAD LOCK IF NEEDED. INSTALLATION IS COMPLETE NOW. 18" 457mm 5 1/16" 129mm 6 1/16" 154mm DETAIL POST POST PIN ABS DISK CONCRETE 13
Bollard Light Installation Guidelines
Bollard Light Installation Guidelines The following is provided as an overview and is not intended to be a comprehensive guide. All installations must be completed by a licensed contractor or electrician
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Type C
Module Type Width Length C 22-27 56-63 Side-of-Pole Mount for 1 Module (SPM1) For Module Type C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 022212-1 Side-of-Pole Mount
More informationVERSA BIKE RACK INSTRUCTIONS
VERSA BIKE RACK INSTRUCTIONS Models #8, 8 Important This rack is designed for use with a or. receiver hitch. The rack is designed to hold a maximum of two bicycles. Do not use it for anything other than
More informationSide-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3348-1 PCN 022212-2 Side-of-Pole Mount for 1 Module
More informationAssembly Instructions
CS-B-FM Assembly Instructions Thank you for purchasing a Shelti product. All of us at Shelti want you to be completely satisfied with your Pro Foos game, so feel free to contact us for help with the assembly
More informationSide-of-Pole Mount for 1 Module (SPM1) For Module Types A & B
Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)
More informationBeach Dolly with cradle & keel pad Assembly Instructions
Beach Dolly with cradle & keel pad Assembly Instructions H G B A D C I J L F PART NAME QTY A. AXLE... 1 with tongue bracket and cradle supports attached B. CRADLE SUPPORT BAR... 2 C. TONGUE... 1 D. TONGUE
More informationROCKSOLID DUAL POST ANCHOR
ROCKSOLID DUAL POST ANCHOR INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 (503) 266-2231 Fax (503) 266-4334
More informationMUELLER. A A Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.
Installation Instructions manual MUELLER table of contents PAGE A-20806 A-20807 Adjustable General Information 2 Technical Data 3 Dimensions 4 Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator
More informationMUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5.
Installation Instructions manual MUELLER table of contents PAGE A-20814 Wall Type General Information 2 Technical Data/ Dimensions Installation 4-5 Maintenance 6 Parts 7 Indicator Post! WARNING: 1. Read
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More informationOUTDOOR BACKSTOP WITH 5'-0" EXTENSION
INSTALLATION INSTRUCTIONS OUTDOOR BACKSTOP WITH 5'-0" EXTENSION NoUU. 00175- _ READ ALL INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING TO INSTALL THIS EQUIPMENT. INSTALLATION / ASSEMBLY OF THIS EQUIPMENT MUST
More informationImportant Note: Tighten lock nuts so the support tubes still swing freely see figure 2. There must be 1 2 threads of bolt past end of lock nuts.
Kit Contents: DESCRIPTION QTY. DESCRIPTION QTY. 2 Shank Assembly 1 Support Tube Assembly 1 Side Tube - Short 2 1-1/4 Shank 1 Center Tube - Long 1 3/8-16 x 2.0 Carriage Bolt 2 5/16-18 x 2.25 Carriage Bolt
More informationBASIN AND WALL MIXER INSTALLATION INSTRUCTIONS
BASIN AND WALL MIXER INSTALLATION INSTRUCTIONS IMPORTANT INFORMATION IMPORTANT All tapware and showers to be installed by a licensed plumber and to Australian Standards. Fit tempering and pressure reduction
More informationHP10168 & HP10169 KITS HP10152 / HP10154 / HP10156
HP10168/&HP10154 HP10169/KITS HP10152 HP10156 HP10152: 2" AMP Air Suspension Spacer Kit Ford F-450 Pickup 2WD & 4WD HP10154: 4" AMP Air Suspension Spacer Kit Ford F-450 Pickup 2WD & 4WD HP10156: 6" AMP
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationSCOUT DECK ANCHOR 3 1/4" BONDING SCREW
SCOUT DECK ANCHOR 16" 16" 1" X 4" ANCHOR BOLT (4) 10" 3 1/8" 5" 6" MIN COPPER WIRE TO ATTACH TO BONDING GRID 3 1/4" BONDING SCREW CONCRETE DECK SPECIFICATIONS: THE AQUA CREEK PRODUCTS' SCOUT DECK ANCHOR
More informationMUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.
Installation Instructions manual MUELLER table of contents PAGE A-20808 General Information 2 Technical Data 3 Dimensions 4 A-20809 Non-Adjustable Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator
More informationAssembly Guide ST200 FUNCTIONAL TRAINER
Assembly Guide ST200 FUNCTIONAL TRAINER Assembly Guide ST200 FUNCTIONAL TRAINER To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding,
More informationB-Too Drilling and Tapping Machine
Material Specifications Powered by hand or with Ridgid 690 (TM-29) High strength, modular aluminum and steel components Inserts any 3 /4" to 1" corporation stop under pressure Extracts threaded corporation
More informationTroyer s Gourd Rack 8 unit F R H O P
B E A D I M-N L Vertical Parts F R H O P Horizontal Parts C G J Updated 11/16 Parts List A: Top of Pole B: Bottom of Pole C: 48 Ground Stake D: Top Perch rods 48 long E: Hub F: Rope Winder w/ attached
More informationBRONZE BUSHING REPLACEMENT PROCEDURE DN345 & NL450C
1 BRONZE BUSHING REPLACEMENT PROCEDURE V.2 12/3/2014 DN345 & NL450C 2 Safety Instructions Removing Walking Beams 3 1. Position spreader on a flat concrete surface capable of supporting weight of spreader
More informationA A A
Mossberg 0 GA Talon T Rear Pistol Grip with Scorpion Recoil System A.5.0.6 A.5.0.6 A.5.0.6 Extended Scorpion Material to Reduce and Discomfort to the Shooter's Hand and Thumb Sure-Grip Texture 70.0.0 Mossberg
More informationFoos 300 Assembly Instructions
Foos 300 Assembly Instructions Thank you for purchasing a Shelti product. All of us at Shelti want you to be completely satisfied with your Foos game, so feel free to contact us for help with the assembly
More informationDeluxe Gourd Racks I D E G A. Parts List. Shown above are parts for the two-level, Deluxe Gourd Rack (DGR 12V)with 12 arms for vertically hung gourds.
Deluxe Gourd Racks H F K I D E J C G A Shown above are parts for the two-level, Deluxe Gourd Rack (DGR V)with arms for vertically hung gourds. Parts List Code Quantity A B C D E F G H I J 6, or 4 6, or
More informationA A A
Winchester SXP Talon T Rear Pistol Grip with Scorpion Recoil Grip A.5.0.65 A.5.0.65 A.5.0.65 Extended Scorpion Material to Reduce and Discomfort to the Shooter's Hand and Thumb Sure-Grip Texture Triton
More informationKERSPLASH POOL CLIMBING WALL INSTALLATION INSTRUCTIONS
TOLL FREE: 1-800-476-7366 VOICE 651-665-9131 FAX 651-665-9130 EMAIL: INFO@POOLCLIMBINGWALLS.COM EVERLAST CLIMBING 1335 MENDOTA HEIGHTS ROAD MENDOTA HEIGHTS, MN 55120 2012 EVERACTIVE BRANDS Congratulations!
More informationTripod Setup Guide (M-TPx)
Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for
More informationMade in U.S.A. Narrow-U Bike Rack Heavy Duty Submittal Sheet. Materials: Finishes: Mount Options: Setbacks:
Submittal Sheet Materials: 2 Schedule 40 Steel Pipe (2.375 OD) Finishes: Galvanized An after fabrication hot dipped galvanized finish is available Powder Coat Our powder coat finish assures a high level
More informationFirst Team Sports, Inc. Stellar Recreational Volleyball System
First Team Sports, Inc. Stellar Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 2 Height Labels L 2 Carabiner Clip C 3 Net Clamp M 1 ½ x 2 Hex Bolt
More informationHoldUp Plus2. Safety Kit included: See additional instructions for installation. REAR WHEEL TRAY. BASE (1x) lock WASHER (1x) KEY (2x) SAFETY CLIP (1x)
HoldUp Plus2 InsTAll This product on 2" hitch version of the HoldUp Front WHEEL TRAY assembly (1x) REAR WHEEL TRAY assembly (1x) wrench (1x) BASE (1x) bolt (8X) Lock WASHER (8X) Washer (8x) KEY (2x) SAFETY
More informationengineered products Foldable Topside Creeper Safety First VIDEO INSTRUCTIONS ARE AVAILABLE ON OUR WEBSITE AT:
engineered products Foldable Topside Creeper Please read and understand all safety advisories and operating instruction in this manual to ensure safe and productive operation of your new Topside Creeper.
More informationNICROS-GRANITPANELS INSTALLATION MANUAL
NICROS-GRANITPANELS INSTALLATION MANUAL NICROS, INC. 845 PHALEN BLVD. ST. PAUL, MN 55106 PHONE: 651.778.1975 FAX: 651.778.8080 THANK YOU FOR YOUR PURCHASE OF THIS NICROS PRODUCT Nicros-GranitPanels are
More informationSHEET 2: VERTICAL INSTALLATION
IMAGE OW1291 OW1293 OW1295 OW1297 AVATAR OW1301 OW1303 OW1305 OW1307 OW1311 OW1313 OW1315 OW1317 OW1331 OW1333 OW1335 OW1337 SHEET 2: VERTICAL INSTALLATION SHEET 3: HORIZONTAL INSTALLATION Drawing: 760883XX
More informationWEIGHT STACK ATTACHMENT. Assembly Manual (888) FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
WEIGHT STACK ATTACHMENT Assembly Manual DF835 (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS
More informationMfg. No: Grass Catcher, Single Bag (Export)
Parts Manual Mfg. No: 7600237 Grass Catcher, Single Bag (Export) Copyright Briggs and Stratton. All Rights reserved 01-Apr-2019 Model Components Table Of Contents Page Single Catcher........................................................................................
More informationTo Purchase This Item, Visit BMI Gaming (800)
How to play the game How to play the game The object of the game is to reach the Game Goal before your opponent. HOW TO START: - A coin toss decides who starts the game. The winner of the coin toss also
More informationTOURNAMENT ICE. 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual
TOURNAMENT ICE 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual Thank you for purchasing a Gold Standard Games product. All of us at Gold Standard Games want you to be
More informationMODEL TRIPEX PULLEY SYSTEM
MODEL 922184 TRIPEX PULLEY SYSTEM 1 PARTS LIST FOR TRIPEX PULLEY SYSTEM Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your
More informationUniversal Anchoring Adapter For Mercedes
Universal Anchoring Adapter For Mercedes Anchoring Pin & Tube Set (For Most Mercedes Models) Users Manual 006 Chief Automotive Technologies, Inc. Chief s Limited One-Year Warranty & Liability CHIEF'S
More informationSAILTEC, INC CONGER COURT, OSHKOSH, WI USA
OK to make this valve hand tight. Pin Mount Style Integral lies 4-5 Degrees above Horizontal. If you store your Hunter "bow down" you will get air-lock in the Integral. Slot Mount Style Pump Body "Down"
More informationSanta Fe Cycles Assembly Guide Introduction
Santa Fe Cycles Assembly Guide Introduction Congratulations on your purchase of your new Santa Fe bicycle. You have purchased a bicycle that has many features and qualities. Please take a few minutes and
More informationOWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL)
OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) Table of Contents ASSEMBLY ASSEMBLY Pistol Bullet Feeder... Page 3 CHANGE-OVERS The Hornady Lock-N-Load Pistol Bullet Feeder is capable of feeding most
More informationFlexfence Swaging Unit. Product Manual. Release 02/16.
Product Manual www.ingalcivil.com.au 1.0 Safety Precautions 1.1 Personal Protection While operating this equipment it is recommended that the following personal protective equipment be worn; Long sleeve
More informationImport Bike Rack OEM INSTALLATION MANUAL
Import ike Rack OEM INSTLLTION MNUL TLE OF ONTENTS System Information 2 Safety Information 2 Resources Required 3 Preparation 3 Under umper ttachment 3 Over umper ttachment 3 Installation 3 Under umper
More informationREAD ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
Drywall Stills DS1830 Max Weight Capacity 225 Lb READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance. Every effort
More informationPaddle Bar Replacement
This procedure is to help facilitate the replacement of the 23 Paddle Bar Assembly on the ANKOM Dietary Fiber Analyzer. Note: The following items will be sent in a replacement package as part of the 23
More informationFIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions
FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY
More informationTHOR 10 HAMMER CAGE INSTRUCTIONS
75 " 7m 78 4" m 6" 8.8m 45 ".70m 4.9deg 6 4" 6m 44 4".67m 75 " 7m 9 4" 0m 44".m 497 4".64m The 70, Thor Hammer Cage, consists of four heavy duty aluminum net poles. The unique pole structure reduces the
More informationLEGACY II TM STARTING PLATFORMS
LEGACY II TM STARTING PLATFORMS INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 (503) 266-2231 Fax (503) 266-4334
More informationTraditional Basketball Set. Assembly & Installation Instructions
Traditional & Pro Style Basketball Set Assembly & Installation Instructions Traditional Basketball Set Pro Style Basketball Set 3 0 5 0 S. A L V E R N O N W A Y T U C S O N, A Z 8 5 7 1 3 5 2 0. 7 9 0.
More informationBACKSTROKE START DEVICE
BACKSTROKE START DEVICE 1551 East 11th Street Loveland CO 80537 +1 970.667.1000 www.coloradotime.com 2016 Colorado Time Systems F1024 Rev 201604 You have purchased a Colorado Time Systems Backstroke Start
More informationBike Rack and Tire Carrier
Bike Rack and Tire Carrier OWNER'S MANUAL Rev: 10.26.2017 Page 1 Bike Rack and Tire Carrier Owners Manual TABLE OF CONTENTS System 2 Description 2 Prior To Operation 3 Manual Slide-Out Bike Rack Operation
More informationMODEL CHEST PULLEY SYSTEM
MODEL 9180 CHEST PULLEY SYSTEM 1 PARTS LIST FOR CHEST PULLEY Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your facility.
More informationROCKSOLID SINGLE POST ANCHOR
ROCKSOLID SINGLE POST ANCHOR INSTALLATION INSTRUCTIONS YOU MUST USE THE ANCHOR SET TOOL (PART #27-109) TO INSURE PROPER INSTALLATION SRS AUSTRALIA, PTY LTD 12 Enterprise St Richlands QLD 4077 Australia
More informationTools for rotary drilling 4 group
4 group - Tools for hand rotary drilling - Tools for mechanical rotary drilling - Tools for underground drilling gotten sucking off method - arge diameter bits and rods for rotary drilling 1 The way of
More informationInstalling a Christie One Mount/Christie One Mount Plus
Installing a Christie One Mount/Christie One Mount Plus This document provides instructions for installing the Christie One Mount or Christie One Mount Plus and optional accessories to mount Christie projectors
More informationRocky Mountain Instinct / Pipeline Alloy Frame Assembly Guide. Date: April 7, 2017
Rocky Mountain Instinct / Pipeline Alloy Frame Assembly Guide Date: April 7, 2017 1 Table of Contents Front Triangle Preparation... 4 Parts Needed... 4 Instructions... 4 Chain Stay Preparation... 6 Parts
More informationFirst Team Sports, Inc. Blast Recreational Volleyball System
First Team Sports, Inc. Blast Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 3 Net Clamp L 2 Carabiner Clip C 1 Pulley Clamp M 1 ½ x 2 Hex Bolt D 4
More informationOWNERS MANUAL. Model Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS
OWNERS MANUAL Model 2400 Shown with optional Primary Mooring Cleats. Portable Mooring System SAFETY OPERATION MAINTENANCE PARTS CAUTION: Before using your new Pier Tender, read rules for Safety, Operation,
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More informationInstallation Guide RHT-380. This Manual Must Be Read Before Operating The Equipment CUSTOMER COPY
Installation Guide This Manual Must Be Read Before Operating The Equipment RHT-380 Madison Heights, Michigan 48071 800-725-8377 www.snowexproducts.com CUSTOMER COPY Trynex International 2013 (REV B) F50767
More informationLow Wind High Yields Series
Low Wind High Yields Series Wind Turbines USER S MANUAL Introduction Low Wind High Yields Series rotor blades apply the latest advanced thermoplastic engineering and are manufactured by precision injection
More information3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO
NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationEngineering Data Sheet
Page 1 of 6 CE MARKING AND THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC Valves must be installed into a well designed system and it is recommended that the system be inspected in accordance with the appropriate
More informationL.Ph. Bolander & Sons 1355 Evans Ave. 800/
L.Ph. Bolander & Sons 1355 Evans Ave. 800/434-5611 San Francisco, Ca. 94124 Fax 415/648-0402 GOUNDSET ALUMINUM FLAGPOLE INSTALLATION INSTRUCTIONS STEP 1: DIG THE HOLE TO THE DIMENSIONS LISTED BELOW STEP
More informationEZ-Mount 4 Spring Enclosed System to 22 (Low & High Mount Applications) Installation Instructions
501-1768 (With Wire) 501-1769 (No Wire) 501-1766 (With Wire) 501-1767 (No Wire) 607-015 WLH 06/20/18 TABLE OF CONTENTS ***Assembly*** ***Parts*** Pivot Points and Mounting Locations (Low Mount)... 1 High
More informationELECTRON PRO: ASSEMBLY GUIDE. Revision Valid for MY2017 Electron Pro
ELECTRON PRO: ASSEMBLY GUIDE Revision 1.0 10-20-2016 Valid for MY2017 Electron Pro ELECTRON PRO: Table of Contents 1. Tools Needed and First Aid Kit...3 2. Specifications...4 3. Configurations...5 4. Geometry...7
More informationInstallation, Operation & Maintenance Manual
Original Instructions Installation, Operation & Maintenance Manual Sentry VREL Control Valve Pressure Conditioning S-SW-IOM-00277-15 1-17 Table of Contents Safety Information... 3 General Safety Precautions...
More informationAmerican Flagpole & Flag Co. 1(800)
SENTRY CONCEALED HALYARD-REVOLVING TRUCK GROUND SET INSTALLATIONS INSTRUCTIONS 1. Dig foundation as detailed in SECTION A FOUNDATION SPECIFICATIONS, set sleeve in enter of hole with top 2 above grade.
More informationAGM 33 PIKE ALL FIBERGLASS. Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List
ALL FIBERGLASS AGM 33 PIKE Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List (1) Filament Wound Nose Cone w/ Metal Tip (1) Nose Cone
More informationSHUR-LOK CORPORATION TECHNICAL SALES BULLETIN
Page 1 of 11 1. SCOPE: 1.1. This provides the minimum design, port preparation, and installation and removal requirements for SLAS5103 plugs and is applicable when specified on engineering drawings. These
More informationSHUR-LOK CORPORATION TECHNICAL SALES BULLETIN
Page 1 of 9 1. SCOPE: 1.1. This provides the minimum design, port preparation and installation and removal requirements for SLAS4383-XX-XX, SLF2002-XX-XX and SLF3004-XX-XX adapter reducer and is applicable
More informationInstallation Procedure for your Disco Double Kit, by Airgun Lab, LLC.
Disco Double Installation Instructions Copyright Airgun Lab LLC Rev D January 2016 page 1 of 6 Installation Procedure for your Disco Double Kit, by Airgun Lab, LLC. Step 1, gather tools. Tools required
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KIT CONTENTS: PART NUMBER: DESCRIPTION: E361SXA300 ROOF MOUNT BICYCLE CARRIER B9 TRIBECA Short Carriage Bolt Long Carriage Bolt 3x Over-Molded Wrench Button Head Screw 2x Washer
More informationMoai Bike Rack Heavy Duty Submittal Sheet. Materials: 2.0 Schedule 40 Pipe (2.375 OD) Finishes: Capacity: Mount Options: Setbacks: 2 Bikes
Submittal Sheet Materials: 2.0 Schedule 40 Pipe (2.375 OD) Finishes: Galvanized An after fabrication hot dipped galvanized finish is available. Powder Coat Our powder coat finish assures a high level of
More informationSwing Set. Sheffield Model 22-PS320
Swing Set Sheffield Model 22-PS320 Important! The owner s manual contains safety, assembly, use and maintenance instructions. The Playsafe Swing Set must be assembled by an adult who has read and understands
More informationBICYCLE ACCESS RAMP INSTALLATION INSTRUCTIONS. Customer Service all4cycling.com.au
BICYCLE ACCESS RAMP INSTALLATION INSTRUCTIONS Customer Service 1300 429 254 all4cycling.com.au Thanks for buying our Bicycle Access Ramp! You re now the proud owner of the Bike Fixation Bicycle Access
More informationINSTALLATION INSTRUCTIONS AT-SERIES ANCHOR ASSEMBLY PART NUMBER: F-04CAJP 450 LB. [204kg] MAXIMUM CAPACITY (PRO POOL LIFT)
INSTALLATION INSTRUCTIONS AT-SERIES ANCHOR ASSEMBLY PART NUMBER: F-04CAJP 450 LB. [204kg] MAXIMUM CAPACITY (PRO POOL LIFT) - WARNING- IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS.
More informationParts: Included in the parts box: Inner Rear Tire Tray. Inner Front Tire Tray. Trail Doc Clamp. Pivot Assembly. Trail Doc Post.
NV 2.0 2 Parts: Outer Front Tire Tray Inner Front Tire Tray Outer Rear Tire Tray Inner Rear Tire Tray Pivot Assembly Trail Doc Clamp Trail Doc Post Included in the parts box: 6mm Allen Wrench M6 Lock Washer
More informationFinal Assembly Instructions Bikes with 16 Wheel Size
Final Assembly Instructions Bikes with 16 Wheel Size Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationSETTING UP THE MODEL 210B SRA
SETTING UP THE MODEL 210B SRA SAFETY PRECAUTIONS FOR THE MODEL 210B SRA System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During
More informationINSTRUCTIONS 360 Y-DROP HAGIE STS 2015
INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INSTRUCTIONS 60 Y-DROP HAGIE STS 05 INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The
More informationFNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions
FNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev: - Page
More informationOPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M)
OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR 04/17 (M6K-M) SERVICING THIS TOOL TABLE
More informationHalsey Taylor Owners Manual STOP!
Halsey Taylor Owners Manual 4710 Freeze Resistant Floor Mounted Steel Fountain STOP! PLEASE READ THE FOLLOWING INFORMATION. ITALLATION ITRUCTIO FOR THE 4710FR FTN. WITH 97243C SINGLE VALVE CONTROL ASSEMBLY
More informationInstallation Instructions
116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting
More informationMarine 6-Boat Free-Standing Racks SKU: Updated November 2011
Marine 6-Boat Free-Standing Racks SKU: 30-061 Updated November 011 Contains: Marine -Boat Free-Standing Racks (SKU 1-003) Marine 3 rd Boat Expansion Racks (SKU 1-0303) Marine Back Legs (SKU -001) 3 Sets
More informationMODEL / SINGLE and DUPLEX PULLEY SYSTEMS
MODEL 922181/922182 SINGLE and DUPLEX PULLEY SYSTEMS MODEL 922181 SINGLE PULLEY SYSTEM MODEL 922182 DUPLEX PULLEY SYSTEM 1 PARTS LIST FOR SINGLE/DUPLEX COLUMN PULLEYS Note: Check with your architect or
More informationFontaine Fifth Wheel Ultra LT Rebuild Procedures
Fontaine Fifth Wheel Ultra LT Rebuild Procedures Disassembly Assembly Adjustments 800-874-9780 2010 LT-147 January 2010 Dissassembly Cover plate removed for clarity. Refer to exploded view of assembly
More informationINSTALLATION INSTRUCTIONS FOR GRT75-PF-RFS PET FOUNTAIN
INSTALLATION INSTRUCTIONS FOR GRT75-PF-RFS PET FOUNTAIN Important: Read all instructions and refer to local codes prior to installation. l Local soil conditions may require more gravel for drainage. l
More informationMASTER TRUING STAND TS-3. Optional Dial indicator set with brackets Dial indicator bracket set only
MASTER TRUING STAND TS-3 3 2 1 3 8 9 4 10 7 6 5 12 13 Optional 1555-1 Dial indicator set with brackets 1556-1 Dial indicator bracket set only 49 11 16 14 15 48 32 31 37 38 20 19 17 18 34 39 21 36 22 33
More information2.4M Viking Swing Basket Swing
.M Viking Swing Basket Swing PROD. CODE SIZE AGE RANGE F/ FALL HEIGHT HEAVIEST PART TOTAL WEIGHT 75x75x150 5 to Adult 1.5 Metres Approx 6Kg Approx 198Kg SPECIFICATION Solid steel components to EN 10087:1998
More informationGurney Flap for WRX and STI w/low Profile Trunk Spoiler
Gurney Flap for 2015+ WRX and STI w/low Profile Trunk Spoiler 2017-12-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced
More informationParts and Service Memo
Parts and Service Memo 4233, 4240, 4250, 5260 Horizontal Shaft Impactors PSM 014 1102 FT C&S HSI SUBJECT: Horizontal Shaft Impactors. Rotor Wedge Update KPI-JCI has made a change to their rotor wedge assembly
More informationPRODUCT CARD WALL MOUNTED FIXED BASKETBALL CONSTRUCTION PROJECTION: FROM 1,00 TO 2,25 M
PRODUCT CARD WALL MOUNTED FIXED BASKETBALL CONSTRUCTION PROJECTION: FROM 1,00 TO 2,25 M I. List of components... 2 II. Complimentary products... 2 III. Product description... 3 IV. Product Purpose... 3
More informationLV LOADER DIRECTIONAL CONTROL VALVES INSTALLATION & USER GUIDE
LV LOADER DIRECTIONAL CONTROL VALVES INSTALLATION & USER GUIDE SPECIFICATIONS: 10 gpm (38 lpm) Nominal Capacity. Rated up to 4000 psi (275 bar). Port Sizes-Inlet/Outlet #8SAE (3/4-16). Work Ports #8SAE
More informationThank you for purchasing a WIKE BOX BIKE!
Thank you for purchasing a WIKE BOX BIKE! Contents Safety.....3 Front wheel.4 Kickstand..5 Handle Bar & Box 6 Seat post and Saddle 7 Final pre-ride check 8 Tools needed to assemble Bike: -High table or
More informationDirectional Valves. Hydraulic Operated Directional Valves
Service Data Vickers Directional Valves Hydraulic Operated Directional Valves (F*) DG3V 8 (B) ** (L) (X) (*) (*) 10 (EN**) Released 04/96 5007.03/EN/0496/S DG3V-8-*(C) - (X) - 10 Spring Centered 473726
More informationThank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step*
PG 1 OF 9 PORTA-DOCK, INC. 74A ABL/APW 1056 & 44A FLB APW 1056 PORTA-LIFT Thank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step* STEP 1. Separate and group
More information