Building 24 Roof Safety Assessment

Size: px
Start display at page:

Download "Building 24 Roof Safety Assessment"

Transcription

1 Roof Safety Survey GENERAL INFORATION CAPUS: Wollongong Campus BUILDING: Teaching Building (24) DESCRIPTION: odern three storey building with low pitch metal roof. orizontal lifelines located 2 metres from building edges. Anchor point on the south side adjacent to the hatch opening. RISK ASSESSENT #: ROOF ACCESS: UOW01624 Access to the roof is via the plantroom on the second floor. A permanently fixed 6 metre ladder ascends to a locked hatch that opens onto the roof. Use caution when climbing the ladder - beware hitting head or back on cable rack which is in close proximity. Telescopic styles to be extended when roof hatch is opened. SIGNAGE: COPLIANCE PLATES: Compliance plate at top of ladder inside the hatch. SAFE WORK AREA: ROOFING SYSTE: Services Area on landing outside access door on level 2 Sala Evolution Lifeline EIGT OF BUILDING: PITC: ROOF CONSTRUCTION: STRUCTURAL INTEGRITY: VEGETATION: Three storey < 10 degrees etal Good ADJOINING ROOFES: Building 19 SERVICES: Gutters Yes Satellite Dishes No A/C Units No Antenna No Exhaust Fans No Skylights Domes No Ducts Yes Glass Skylights No Roof Ventilators Yes Pipework No Fume Cupboards No Cooling Tower No Telco Towers No EXISTING SAFETY ITES: orizontal Lifelines Yes andrail Yes Anchor Points Yes Walkway No Vertical Lifelines No Parapets Yes WORK ACTIVITY DETAILS: Clean Gutters / Routine aintenance Frequency TBA Note: Before commencing any work obtain Roof Permit from Facilities anagement Division

2 Roof Safety Survey RISK ASSESSENT Risk Assessment / Task Location BUILDING 24 Note: The hazards identified do not include hazards that related to specific work tasks. These should be identified in the Safe Work ethod Statement (SWS) of the contractor. What is the Activity / Service Item azard Identification What are the potential azards Risk Assessment & Control easures What is the Risk Level List any Control easures already Implemented Risk Control Describe what can be done to eliminate risk or reduce the harm Access to Roof via Ladder Access to Roof via Ladder Gutter aintenance on Roof Roof Plant aintenance greater than 2m from roof edge Roof Plant aintenance within 2m from roof edge Falling Low head clearance Falling Refer to SWS for contractor Falling & Refer to SWS for contractor Access to Roof Unauthorised access Trip azard - Roof Sheeting Trip azard - orizontal Lifeline or Anchor Points Weather Trips/Slips - Wet Roofs Weather - Windy Condition Weather - ot Conditions aintain 3 points of contact; Signage; and Working at eights Guidelines - Working from Ladders orizontal Lifeline & Anchors Installed orizontal Lifeline & Anchors Installed All access points to roof are locked and made secure so are not accessable by unauthorised persons; signage Signage & System is visible, do not work on wet roof, do not work in high wind conditions Install Vertical Fall Protection System on ladder Signage and/or Relocate electical cable rack away from ladder Ensure horizontal lifeline & anchors used correctly Ensure horizontal lifeline & anchors used correctly Risk Assessment and Roof Safety Survey Walkway or minimum awareness in Be aware of location of horizontal lifeline & anchor points Do not work while roofs are wet or have dew Do not work in windy conditions Use suncream, hats and remain hydrated and take appropriate breaks

3 Reference Documentation Legislation NSW Work ealth and Safety Regulation 2011 Part 4.4 Falls Australian Standards AS : Fixed platforms, walkways, stairways and ladders - Design, construction and installation AS : Industrial fall-arrest systems and devices - arnesses and ancillary equipment AS : Industrial fall-arrest systems and devices - orizontal lifeline and rail systems AS : Industrial fall-arrest systems and devices - Fall-arrest devices AS : Industrial fall-arrest systems and devices - Selection, use and maintenance AS : Safety, protective and occupational footwear - Guide to selection, care and use AS : Temporary edge protection - requirements AS : Temporary edge protection - Roof edge protection - Installation and dismantling AS : anufacturing requirements for single-point anchor device used for harness-based work at height Code of Practice Australia - anaging the Risk of Falls at Workplaces UOW Documentation anaging the Risk of Falls Guidelines Thermal Comfort Guidelines UOW Roof Access Permit UOW Roof Access Certificate Other WorkCover - ing at eights Guide 2006

4

5 Access from Building 24 to landing Service on Landing Ladder in plantroom North eastern corner North western corner South western corner South eastern corner Access hatch

Building 9 Roof Safety Assessment

Building 9 Roof Safety Assessment Roof Safety Survey GENERAL INFORMATION Building 9 Roof Safety Assessment CAMPUS: Wollongong Campus BUILDING: Sports Hub (9) DESCRIPTION: Two storey metal roof building with no internal roof access and

More information

Building 31A Roof Safety Assessment. UOW01628 Access Hatch from Second Floor Yes

Building 31A Roof Safety Assessment. UOW01628 Access Hatch from Second Floor Yes Roof Safety Survey GENERAL INFORMATION Building 31A Roof Safety Assessment CAMPUS: Wollongong Campus BUILDING: Facilities Management Division (31 A) DESCRIPTION: Two storey metal roof building comprising

More information

Building 21 Roof Safety Assessment. Multi Story Building with large metal roof areas Exteral access required for window cleaning UOW01613

Building 21 Roof Safety Assessment. Multi Story Building with large metal roof areas Exteral access required for window cleaning UOW01613 Roof Safety Survey GENERAL INFORMATION CAMPUS: Wollongong Campus BUILDING: 21 Early Start Facility DESCRIPTION: RISK ASSESSMENT # ROOF ACCESS: Multi Story Building with large metal roof areas Exteral access

More information

Building 43 Roof Safety Assessment

Building 43 Roof Safety Assessment Roof Safety Survey GENERAL INFORMATION CAMPUS: Wollongong Campus BUILDING: Building 43 Building 43 Roof Safety Assessment DESCRIPTION: RISK ASSESSMENT # : ROOF ACCESS: SIGNAGE: COMPLIANCE PLATES: SAFE

More information

Building 30 Roof Risk Assessment

Building 30 Roof Risk Assessment Roof Safety Survey GENERAL INFORMATION Building 30 Roof Risk Assessment CAMPUS: Wollongong Campus BUILDING: Woolyungah Indigenous Centre / UOW College (30) DESCRIPTION: L shaped 2 storey building with

More information

Building 32A Roof Safety Assessment

Building 32A Roof Safety Assessment Roof Safety Survey GENERAL INFORMATION Building 32A Roof Safety Assessment CAMPUS: Wollongong Campus BUILDING: Print & Distribution (32A) Building is a two storey metal warehouse structure with steeply

More information

International House Roof Safety Assessment. 3 storey student accomodation units with tile roofs. Nil - Anchor points are not compliant None

International House Roof Safety Assessment. 3 storey student accomodation units with tile roofs. Nil - Anchor points are not compliant None Roof Safety Survey GENERAL INFORMATION CAMPUS: Wollongong Residential BUILDING: International House International House Roof Safety Assessment DESCRIPTION: RISK ASSESSMENT # : ROOF ACCESS: SIGNAGE : COMPLIANCE

More information

Building 68 Roof Safety Assessment

Building 68 Roof Safety Assessment Roof Safety Survey GENERAL INFORMATION CAMPUS: Wollongong BUILDING: Building 68 Kooloobong Stage 2 DESCRIPTION: Modern E shaped unit accommodation block comprising of three wings. Pitch and level of roof

More information

Building 16 Roof Safety Assessment

Building 16 Roof Safety Assessment Building 16 Roof Safety Assessment Roof Safety Survey GENERAL INFORMATION CAMPUS: Wollongong Campus BUILDING: Library (16) DESCRIPTION: Original flat concrete roof surrounded by handrail and parapet. More

More information

Safety Risk Assessment Roofing Works / Surveying / Inspections

Safety Risk Assessment Roofing Works / Surveying / Inspections One Direct aintenance td Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees ark Bloxidge H&S anager 0208 821 5197 One Direct Operatives accessing roof

More information

Develop and sign off on risk assessment/work method statement for the task, considering task specifics elements that will affect the user s safety:

Develop and sign off on risk assessment/work method statement for the task, considering task specifics elements that will affect the user s safety: Safe Use Step 1 Complete your site induction with the RIS Altitude system owner and confirm that the users can demonstrate competence in the activity of working at heights by provision of a nationally

More information

FATAL AND SEVERE RISK PROGRAM

FATAL AND SEVERE RISK PROGRAM FATAL AND SEVERE RISK PROGRAM LEADER SESSION FALL FROM HEIGHTS Only do the task if it can be done safely FALL FROM HEIGHTS OUR COMMITMENT LIFE SAVING BEHAVIOUR: I WILL ALWAYS USE ADEQUATE PROTECTION WHERE

More information

2018 INSPECTION REPORT

2018 INSPECTION REPORT 2018 INSPECTION REPORT Compiled For Queensland University of Technology KELVIN GROVE CAMPUS INTRODUCTION Height Dynamics is an innovative height safety company that provides a diverse range of products

More information

Applying Construction Fall Protection Concepts to General Industry

Applying Construction Fall Protection Concepts to General Industry Applying Construction Fall Protection Concepts to General Industry Applying Construction Fall Protection Concepts to General Industry Michael Tesmer, CSP and David Jewell, CSP Conney Safety Products This

More information

8. Fall Protection Procedures WAC

8. Fall Protection Procedures WAC 1.0 Fall Protection Introduction 8. Fall Protection Procedures WAC 296-155-245 If an employee is exposed to a fall hazard of ten (10) feet or more in height, the employee must use a fall restraint, fall

More information

1 AIM 2 4 REASONS FOR INCLUSION 3 6 PLANT AND EQUIPMENT REQUIREMENTS 4 7 SYSTEM AND PROCEDURAL REQUIREMENTS 4 8 PEOPLE REQUIREMENTS 6

1 AIM 2 4 REASONS FOR INCLUSION 3 6 PLANT AND EQUIPMENT REQUIREMENTS 4 7 SYSTEM AND PROCEDURAL REQUIREMENTS 4 8 PEOPLE REQUIREMENTS 6 CONTENTS PAGE 1 AIM 2 2 APPLICATION 2 3 DEFINITIONS 2 4 REASONS FOR INCLUSION 3 5 REQUIREMENTS 3 6 PLANT AND EQUIPMENT REQUIREMENTS 4 7 SYSTEM AND PROCEDURAL REQUIREMENTS 4 8 PEOPLE REQUIREMENTS 6 APPENDIX

More information

Safe Work Method Statement

Safe Work Method Statement TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Working at eight SWMS No. 16 Authorized and email Signed by the (Managing

More information

This subject outlines procedures to prevent accidents or injuries to you and others from inappropriate selection and use of fall protection equipment.

This subject outlines procedures to prevent accidents or injuries to you and others from inappropriate selection and use of fall protection equipment. Page 1 of 7 REFERENCES Personal Protective Equipment Standards 1.31 PURPOSE This subject outlines procedures to prevent accidents or injuries to you and others from inappropriate selection and use of fall

More information

Prevention of Falls and Working at Heights

Prevention of Falls and Working at Heights Workplace Safety Schools Cleaning Prevention of Falls and Working at Heights It is the policy of the Company to avoid working at heights above 2 metres wherever practical. When avoidance is not an option,

More information

Telco Antennas SWMS Working At Height Above 2m

Telco Antennas SWMS Working At Height Above 2m Telco Antennas SWMS Working At Height Above 2m A SWMS shall be developed for a task where the risk has been assessed as Medium or Higher Division: Date: SWMS No: (e.g. Installation, Engineering Workshop)

More information

FALL PROTECTION PLAN INSTRUCTIONS

FALL PROTECTION PLAN INSTRUCTIONS Sonic Drilling Ltd. FALL PROTECTION PLAN INSTRUCTIONS Each employer must ensure that a fall protection system is used when work is done at a place from which a fall of 3 m (10 ft) or more may occur, or

More information

GARDENS POINT CAMPUS

GARDENS POINT CAMPUS 08 INSPECTION REPORT Compiled For Queensland University of Technology GARDENS POINT CAMPUS INTRODUCTION Height Dynamics is an innovative height safety company that provides a diverse range of products

More information

FALL PROTECTION

FALL PROTECTION 115500 FALL PROTECTION PART 1 GENERAL 1.01 General A. Cornell University seeks to prevent exposures to fall hazards whenever possible and protect personnel that may be exposed to fall hazards. Therefore,

More information

LADDERS FIXED AND PORTABLE

LADDERS FIXED AND PORTABLE CONTRACTOR WHS HAZARD STANDARD LADDERS FIXED AND PORTABLE EXTERNAL USE ONLY Principles in the Optus Contractor WHS management process CONTRACTOR MANAGEMENT STAGES PRINCIPLES THIS STANDARD REQUISITION Requisition

More information

DREW UNIVERSITY FALL PROTECTION PROCEDURE (DRAFT 12/11)

DREW UNIVERSITY FALL PROTECTION PROCEDURE (DRAFT 12/11) PURPOSE The objective of this policy & guideline is to eliminate the potential for injuries and fatalities to employees and contractors resulting from falls from elevated work areas at Drew University

More information

7 Hazard assessment 8 Worker participation 9 Hazard elimination and control

7 Hazard assessment 8 Worker participation 9 Hazard elimination and control This document is a guideline only. Employers have a responsibility of assessing all applicable occupational health and safety legislation, for the tasks they are performing. Businesses in this industry

More information

Application Showcase LIFE MATTERS TM

Application Showcase LIFE MATTERS TM Application Showcase LIFE MATTERS TM Diversified Fall Protection specializes in the design, development, and manufacture of engineered fall protection systems designed to keep workers safe while working

More information

??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls.

??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls. Intent??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls. Fall Protection is an integral part of our commitment to a safe work

More information

SAFE WORK METHOD STATEMENT 0005 (Hang-On Platform) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities)

SAFE WORK METHOD STATEMENT 0005 (Hang-On Platform) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities) Contractor Company Details: BUILDSAFE SAFE WORK METHOD STATEMENT 0005 (Hang-On Platform) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities) Additional Information (if required):

More information

FALL PROTECTION PROGRAM (OHS-0010)

FALL PROTECTION PROGRAM (OHS-0010) () For Issued: December 17, 2007 Revised: 1 st Issue PAGE 1 OF 17 Table of Contents 1.0 Purpose...2 2.0 Document Control...2 2.1 Approvals...2 2.2 Responsibility...2 3.0 Definitions...3 4.0 Objective...7

More information

Work at height Policy

Work at height Policy Work at Policy Introduction This policy procedure outlines the Forces responsibility to provide guidance to all police officers and staff when working at. Many serious incidents involving working at occur

More information

Deans, Directors, Heads of Schools and Departments and Research Institute Directors and Managers

Deans, Directors, Heads of Schools and Departments and Research Institute Directors and Managers Working at Height 1. PURPOSE 1.1 To ensure that any work at height is carried out in accordance with the legal requirements and associated guidance. This includes the use of scaffolds, towers, ladders,

More information

Fall Protection on Low Sloped Roofs for General Industry. Presented by: Brian Stickler

Fall Protection on Low Sloped Roofs for General Industry. Presented by: Brian Stickler Fall Protection on Low Sloped Roofs for General Industry Presented by: Brian Stickler Learning Objectives: Learn how to identify hazard areas on the roof Determine what OSHA considers to be a hole on the

More information

Training Manual RIIWHS204D Work Safely at Heights

Training Manual RIIWHS204D Work Safely at Heights Training Manual RIIWHS204D Work Safely at Heights START TIME: 7.45AM SHARP Participants must read this manual prior to attending the training program and are required to bring the manual to the training

More information

Working at Height. Policy and Procedures. Author: Beth Webster Assistant Safety Advisor. On behalf of School Safety Committee.

Working at Height. Policy and Procedures. Author: Beth Webster Assistant Safety Advisor. On behalf of School Safety Committee. Working at Height Policy and Procedures Author: Beth Webster Assistant Safety Advisor Authorised by: Issued by: John Stephenson Safety Office On behalf of School Safety Committee Review Date: NO LATER

More information

PRO Working at Height

PRO Working at Height MS&L Procedure PRO-4.5-0001-1-05 Working at Height Version: 3 Authorised by: Tom Angliss & Owen Quake Authorisation Date: 21/11/2017 This document has been approved for release and changed as per the associated

More information

Safe Working at Heights Theory Assessment

Safe Working at Heights Theory Assessment Safe Working at Heights Theory Assessment Version 4.00 Safe Working at Heights Theory Assessment This Theory Assessment will form part of the formal assessment for the following unit/s of competency: RIIWHS204D

More information

Anchor on the Go. Portable Roof Anchor for Metal Roofs. Part Number Patent Number Installation and Operating Instructions

Anchor on the Go. Portable Roof Anchor for Metal Roofs. Part Number Patent Number Installation and Operating Instructions Anchor on the Go Portable Roof Anchor for Metal Roofs Part Number 762998 Patent Number 2003258383 Installation and Operating Instructions WARNING: This product is part of a fall protection system. Users

More information

Safe Work Method Statement (SWMS)

Safe Work Method Statement (SWMS) Safe Work Method Statement (SWMS) Work Activity/Description: Site Name: Date: Site Address: Name Position Signature Document No: Prepared By: OHS Manager Revision: Reviewed By: National Program Manager

More information

WORKING AT HEIGHTS MANUAL

WORKING AT HEIGHTS MANUAL WORKING AT HEIGHTS MANUAL 1300 301 755 SAYFA.COM.AU 1 ABOUT SAYFA Sayfa Group leads the industry in the design, installation and management of access, fall protection and ground safety systems. The In-Action

More information

CONTRACTOR WHS HAZARD STANDARD CONFINED SPACE EXTERNAL USE ONLY

CONTRACTOR WHS HAZARD STANDARD CONFINED SPACE EXTERNAL USE ONLY CONTRACTOR WHS HAZARD STANDARD CONFINED SPACE EXTERNAL USE ONLY Principles in the Optus Contractor WHS management process CONTRACTOR MANAGEMENT STAGES PRINCIPLES THIS STANDARD REQUISITION Requisition WHS

More information

SOP. Working in Confined Spaces

SOP. Working in Confined Spaces Purpose This procedure outlines the requirements for the management of entry into confined spaces in all work areas with the intention of minimising risks to health and safety from any potential hazards

More information

J&S Cooper Utilities

J&S Cooper Utilities Working at Heights Inspection conducted for J&S Cooper Utilities Conducted on 17 Apr 2018 08:35 AM Location 11953 Tyler Rd, Red Bluff, CA 96080, USA Prepared by SafetyCulture Staff Completed on 17 Apr

More information

FALL PROTECTION WORK PLAN (Alstom Power Installation Canada)

FALL PROTECTION WORK PLAN (Alstom Power Installation Canada) FALL PROTECTION WORK PLAN (Alstom Power Installation Canada) Location: Unit: Foreman: Task: Supervisors Ensure: Workers must review and sign this fall protection work plan prior to starting work in an

More information

Safe Work Method Statement (SWMS)

Safe Work Method Statement (SWMS) Safe Work Method Statement (SWMS) Organisation Details : Organisation Name Northern Plumbing Contact ABN 17 15 41 4 Position Director Address 47 Thomas Street Edgeworth 85 Phone Number 0411 10 4 Project

More information

Work At Height Health & Safety Management Standard Issue 3 (April 2011)

Work At Height Health & Safety Management Standard Issue 3 (April 2011) Work At Height Health & Safety Management Standard Issue 3 (April 2011) Introduction This document contains corporate standards and guidance on the management of risks arising from work at height. It is

More information

SAFE WORK METHOD STATEMENT 0003 (Perimeter and Balcony Fallguard) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities)

SAFE WORK METHOD STATEMENT 0003 (Perimeter and Balcony Fallguard) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities) Contractor Company Details: BUILDSAFE SAFE WORK METHOD STATEMENT 0003 (Perimeter and Balcony Fallguard) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities) Additional Information

More information

HS26 Working at Height Policy and Procedure

HS26 Working at Height Policy and Procedure HS26 Working at Height Policy and Procedure HS26: Working at Height Policy and Procedure v2-0.jun 2016 Page 1 of 8 1. Scope This policy applies to all staff, students and visitors to The Shared Learning

More information

Important Safety Information Enclosed

Important Safety Information Enclosed Important Safety Information Enclosed ShedBoss Safety Pack NOTE: ENSURE YOUR CONSTRUCTION CREW RECEIVES THIS PACK TO COMPLY WITH SAFE WORK AUSTRALIA CODE OF PRACTICE www.shedboss.com.au Important Safety

More information

SAFE WORK METHOD STATEMENT (SWMS) GENERAL GARDENING with Blowers, Hedge Trimmers, Whipper Snippers, Pruners, Spray Units

SAFE WORK METHOD STATEMENT (SWMS) GENERAL GARDENING with Blowers, Hedge Trimmers, Whipper Snippers, Pruners, Spray Units Job Description/Task/: General Gardening such as using Blowers, Hedge Trimmers, Whipper Snippers, Pruners, Spray Units Name and Phone Number of Person Completing SWMS: Name and Phone Number of the Person

More information

Subparts D and I Walking-Working Surfaces & Personal Protective Equipment Final Rule

Subparts D and I Walking-Working Surfaces & Personal Protective Equipment Final Rule Subparts D and I Walking-Working Surfaces & Personal Protective Equipment Final Rule OSHA s Mission To Assure So Far as Possible Every Working Man and Woman in the Nation Safe and Healthful Working Conditions...

More information

Company Name: Address: ABN: Company Contact: Position: Phone No.: Date SWMS provided to Principal Contractor: Principal Contractor Signature: Date:

Company Name: Address: ABN: Company Contact: Position: Phone No.: Date SWMS provided to Principal Contractor: Principal Contractor Signature: Date: Page 1 of 15 ACTIVITY: Heights - Working at SWMS No.: SAFE WORK METHOD STATEMENT (SWMS) - Part 1 Company Name: Address: ABN: Company Contact: Position: Phone No.: Project Details Project: Job Address:

More information

FCX Department of Occupational Health and Safety. Flagging and Barricading Guideline

FCX Department of Occupational Health and Safety. Flagging and Barricading Guideline FCX Department of Occupational Health and Safety Flagging and Barricading Guideline Approval Date: 11/12/13 Original Date: 03/30/09 SOP # FCX-19 Revision # 1 Supersedes X High Medium Task Risk Low NA Contents

More information

Compliance Is the First Step on the Safety Ladder Understanding the final walking-working surface rule from OSHA and how Honeywell ladder solutions

Compliance Is the First Step on the Safety Ladder Understanding the final walking-working surface rule from OSHA and how Honeywell ladder solutions Compliance Is the First Step on the Safety Ladder Understanding the final walking-working surface rule from OSHA and how Honeywell ladder solutions keep you protected OSHA Walking-Working Surface Rule

More information

GUIDE 2002 HEALTH AND SAFETY FOR ARTIFICIAL CLIMBING STRUCTURES AND OPERATIONS FOR DESIGNERS, MANUFACTURES, SUPPLIERS, OPERATORS AND USERS

GUIDE 2002 HEALTH AND SAFETY FOR ARTIFICIAL CLIMBING STRUCTURES AND OPERATIONS FOR DESIGNERS, MANUFACTURES, SUPPLIERS, OPERATORS AND USERS HEALTH AND SAFETY FOR ARTIFICIAL CLIMBING STRUCTURES AND OPERATIONS FOR DESIGNERS, MANUFACTURES, SUPPLIERS, OPERATORS AND USERS GUIDE 2002 WorkCover NSW Health and Safety Guide WorkCover Watching out for

More information

OSHA 29CFR 1910 Subpart D Walking-Working Surfaces Content

OSHA 29CFR 1910 Subpart D Walking-Working Surfaces Content OSHA 29CFR 1910 Subpart D Walking-Working Surfaces Content 1910.28 Duty to have Fall Protection and Falling Object Protection 1910.29 Fall Protection Systems and Falling Object Protection Criteria and

More information

Work At Heights Toolkit. for Supervisors

Work At Heights Toolkit. for Supervisors Work At Heights Toolkit for Supervisors For Supervisors How to use this toolkit? The toolkit aims to provide information for supervisor to communicate one topic a day to workers. Pictures are for illustration

More information

Overview. Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used

Overview. Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used FALL PROTECTION Overview Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used Fall Protection All situations that expose personnel to

More information

LIGHTHOUSE SAFETY TRAINING 2018

LIGHTHOUSE SAFETY TRAINING 2018 Specialists in Fall Protection, Rescue and Confined Spaces tele (262) 790.1155 fax (262) 783-6211 www.lighthousesafety.com csr@lighthousesafety.com 3620 North 126th Street Brookfield, WI 53005 LIGHTHOUSE

More information

WORKING AT HEIGHTS CS-PTW-HAZ-02

WORKING AT HEIGHTS CS-PTW-HAZ-02 CS ENERGY PROCEDURE FOR WORKING AT HEIGHTS CS-PTW-HAZ-02 Responsible Officer: Corporate PTW Administrator Responsible Executive: Chief Executive Officer (CEO) DOCUMENT HISTORY Key Changes Prepared By Checked

More information

Fall Protection Program

Fall Protection Program Fall Protection Program 135 College Street, Suite 100, New Haven, CT 06510 Telephone: 203-785-3550 / Fax: 203-785-7588 ehs.yale.edu 6/26/2018 CONTENTS: 1. Introduction... 3 2. Responsibilities... 3 A.

More information

Working at Heights Training Checklist (Ontario Version)

Working at Heights Training Checklist (Ontario Version) Working at Heights Training Checklist (Ontario Version) The new working at heights training is different from the fall protection training required by Sec. 26.2(1) of the Ontario Construction Projects

More information

You must NOT touch any equipment unless you are authorised to work on or with that equipment and you have followed correct safety procedures.

You must NOT touch any equipment unless you are authorised to work on or with that equipment and you have followed correct safety procedures. SYDNEY TOWN HALL 1 HIRER & CONTRACTOR SAFETY FACT SHEET Issue 2 September 2013 www.sydneytownhall.com.au City of Sydney - Venue Management will provide and maintain a safe working environment for the health,

More information

Health and Safety Code of Practice. SCP38 Working at Height

Health and Safety Code of Practice. SCP38 Working at Height Health and Safety Code of Practice Responsibility for Policy: Relevant to: Approved by: Responsibility for Document Review: SCP38 Working at Height Date introduced: February 2007 Date(s) modified: Finance

More information

Thanks To Our Sponsors Platinum Sponsor NS Department of Labour and Workforce Development

Thanks To Our Sponsors Platinum Sponsor NS Department of Labour and Workforce Development March 25, 26, 27, 2009 Thanks To Our Sponsors Platinum Sponsor NS Department of Labour and Workforce Development Special Event Sponsor Workers Compensation Board of Nova Scotia Gold Sponsors Maxwell Promotions

More information

KG Training and Assessing. IMPORTANT! You must read this letter!

KG Training and Assessing. IMPORTANT! You must read this letter! IMPORTANT! You must read this letter! ABN: 421 334 328 63 National Provider Number (RTO ID): 52112 Location: Unit 1/8 Day Road, Rockingham WA 6168 Postal Address: PO Box 2111Rockingham DC WA 6967 Ph: 08

More information

Working at Height. A printed or saved copy is an UNCONTROLLED copy. Check that it is the latest available version before use.

Working at Height. A printed or saved copy is an UNCONTROLLED copy. Check that it is the latest available version before use. A printed or saved copy is an UNCONTROLLED copy. Check that it is the latest available version before use. Title: Number: WORKING AT HEIGHT CSBP-GM-11-031-02 Version Number: 24.0.0 Date Revised: 10 September

More information

CHAPTER 10 FALL PROTECTION

CHAPTER 10 FALL PROTECTION CHAPTER 10 FALL PROTECTION A. INTRODUCTION... 1 B. CHAPTER-SPECIFIC ROLES and RESPONSIBILITIES... 2 C. HAZARD IDENTIFICATION... 3 1. Job Hazard Analysis (Jha).... 3 2. Fall Hazards... 3 D. HAZARD CONTROL...

More information

Ormiston Academies Trust. Ormiston Horizon Academy. Working at Height Policy October 2016

Ormiston Academies Trust. Ormiston Horizon Academy. Working at Height Policy October 2016 Ormiston Academies Trust Ormiston Horizon Academy Working at Height Policy Project/job number: Author: Sharlene Smith/Handsam Date: 25/10/16 Contributors: Sharlene Smith Version number: 1.1 Reviewed by:

More information

Department of Facilities Management. Occupational Health and Safety. Fall Protection Program

Department of Facilities Management. Occupational Health and Safety. Fall Protection Program Department of Facilities Management Occupational Health and Safety Fall Protection Program October 2016 1 1.0 INTRODUCTION This program has been developed to provide guidance to those managers and supervisors

More information

SWMS documented by: Feb Bo Ceprnja Date Feb Feb Feb 2018

SWMS documented by: Feb Bo Ceprnja Date Feb Feb Feb 2018 Contractor Company Details: BUILDSAFE SAFE WORK METHOD STATEMENT 0002 (Void Platform Stairs) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities & SWMS 0002 Void Platform) Additional

More information

PRO Working at Height

PRO Working at Height MS&L Procedure PRO-4.5-0001-1-05 Working at Height Document Owner: Bill Kruesi HSSE Manager - Asset Mgmt. Approved By: Prepared By: Document Status: Version Number: 4 Owen Quake Bill Kruesi Adrian Connolly

More information

WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST

WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST Windmill Hazard Inspection Checklist WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST Authorised by: LOCATION OF INSPECTION...... Inspected By (1)........... (2)..... PRINT PRINT Signature (1):. (2)....

More information

FALL PROTECTION CODE OF PRACTICE

FALL PROTECTION CODE OF PRACTICE FALL PROTECTION CODE OF PRACTICE This guide can help you comply with Section 50.2 of the General Regulation 91-191. NOTE: Not for use when a safety monitor is part of the fall protection system on a work

More information

Harbour Town Gold Coast Site Induction

Harbour Town Gold Coast Site Induction Harbour Town Gold Coast Site Induction At Harbour Town Gold Coast we believe that safety is integral to the way we do business. We are committed to operating a safe environment for all where we are incident

More information

FALL PROTECTION GUIDELINE

FALL PROTECTION GUIDELINE FALL PROTECTION GUIDELINE July 2001 Table of Contents INTRODUCTION...3 CONTROL MEASURES...4 SURFACE PROTECTION...4 FIXED BARRIERS...5 EXAMPLES OF GUARDRAIL...6 WARNING BARRIERS...7 HANDRAILS...8 SURFACE

More information

The following items represent the bulk of the exposure to falls on a construction site.

The following items represent the bulk of the exposure to falls on a construction site. Falls Page 60 Wily Coyote always seems to fall into a deep canyon and not be injured at all. People can t. Then why do we seem to have trouble getting workers to pay attention to the fall hazards around

More information

SWMS No 012 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6

SWMS No 012 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6 Samark North Qld Pty Ltd SWMS SWMS No 0 Samark North Qld Pty Ltd ABN : 99 08 98 87 Electrical Contractors License C37 Page of 6 Safe Work Method Statement Title: SWMS:0 INSTALLING LIGHT POLES Work Method

More information

FALL PREVENTION PROCEDURE

FALL PREVENTION PROCEDURE TABLE OF CONTENTS 1. OBJECTIVE... 3 2. SCOPE... 3 3. DEFINITIONS... 3 4. RESPONSIBILITIES... 4 5. HAZARD AND RISK ASSESSMENT... 4 5.1 WORKING AT HEIGHT PERMIT... 4 5.1.1 Permit Currency... 5 5.1.2 Working

More information

SAFE WORK METHOD STATEMENT

SAFE WORK METHOD STATEMENT SAFE WORK METHOD STATEMENT EXCAVATION OR TRENCHING Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES

More information

EZ SERIES FIXED ACCESS LADDERS

EZ SERIES FIXED ACCESS LADDERS EZ SERIES FIXED ACCESS LADDERS Engineered from the ground up for OSHA 1910.3 COMPLIANCE Installs in three easy steps 1 ATTACH MOUNTING BRACKETS PLACE RUNG IN BRACKET 3 SECURE WITH BOLTON CAPTURE PLATE

More information

SECTION FACILITY FALL PROTECTION PART I - GENERAL

SECTION FACILITY FALL PROTECTION PART I - GENERAL SECTION 11 24 29 - FACILITY FALL PROTECTION PART I - GENERAL 1.1 The Illinois Department of Labor (IDOL) regulates fall protection for general industry and construction in the public sector under the Illinois

More information

The content of this resource has been generously provided by the AGC Houston, the Associated General Contractors of America.

The content of this resource has been generously provided by the AGC Houston, the Associated General Contractors of America. Construction & Utilities Division Planning Tools The content of this resource has been generously provided by the AGC Houston, the Associated General Contractors of America. Guidelines for Creation of

More information

"FALL PREVENTION IN THE WORKPLACE"

FALL PREVENTION IN THE WORKPLACE MAJOR PROGRAM POINTS "FALL PREVENTION IN THE WORKPLACE" Part of the "GENERAL SAFETY SERIES" Quality Safety and Health Products, for Today...and Tomorrow Outline of Major Points Covered in the "Fall Protection"

More information

S31 Opening Statement Working at Height

S31 Opening Statement Working at Height S31 Opening Statement Working at Height Falls from height are by far the most common cause of workplace deaths and one of the main causes of major injury in the workplace. Latest figures reveal that 46

More information

WHS PROCEDURE P Confined Spaces. Approved by: Ruth Hampton Review Date: 6 th December 2015

WHS PROCEDURE P Confined Spaces. Approved by: Ruth Hampton Review Date: 6 th December 2015 5 WHS PROCEDURE P21-01 Page 1 of 7 Issue: 2 1. Intent The Salvation Army Australia Eastern Territory (TSA-AUE) is committed to the provision of a safe, healthy and injury free environment for all persons

More information

Fall Protection and Elevated Work

Fall Protection and Elevated Work Program No: SP-010 Page 1 1.0 PURPOSE AND INTRODUCTION Fall Protection and Elevated Work To establish fall protection safety procedures for Pitt County Schools employees engaged in any of the following

More information

1.0 Scope and Application

1.0 Scope and Application 1.0 Scope and Application This policy contains safety requirements to protect employees from falls of six (6) feet or more when performing elevated work except on ladders and scaffolding (See Ladders and

More information

1. Objective of the initiative To ensure that all employees and subcontractors are aware of the risks associated with working at height.

1. Objective of the initiative To ensure that all employees and subcontractors are aware of the risks associated with working at height. Safety Initiative 02 Working at Height May 2011 CONTENTS 1. Objective of the initiative 2. Overview. 3. Implementation 4. Duties 5. Hierarchy of Controls 6. Workplace Inspections 7. Fragile Surfaces 8.

More information

ARKANSAS TECH UNIVERSITY FACILITIES MANAGMENT HEALTH AND SAFETY MANUAL

ARKANSAS TECH UNIVERSITY FACILITIES MANAGMENT HEALTH AND SAFETY MANUAL FALL PROTECTION (PERSONAL FALL ARREST SYSTEMS) 15.0 The purpose of this policy is to specify procedures and training for the safety of the employees in the Facilities Management Group while working on

More information

Safe Work Method Statement

Safe Work Method Statement TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Dogging of Crane General Loading and Unloading SWMS No. 20 Authorized

More information

Specialists Window Cleaning Induction

Specialists Window Cleaning Induction Specialists Window Cleaning Induction Mobile Tower Scaffolds Mobile tower scaffolds are used on flat firm, stable ground to access higher levels. They have toe boards, mid rails & guard rails to prevent

More information

The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field.

The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Purpose The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Fall Protection and Prevention JELD-WEN Field Employees

More information

Developmental Products

Developmental Products Types of Ropes Courses Developmental Products Contents Types of Developmental Ropes Courses Page RCD Developmental Elements 2-3 RCD Linear Ropes Course 4-6 RCD All in One Ropes Course 7-9 RC D Free Standing

More information

Fewer parts. Fast installs. ANSI Compliant. 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems

Fewer parts. Fast installs. ANSI Compliant. 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems Fewer parts. Fast installs. ANSI Compliant. 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems Adding or upgrading your vertical safety

More information

Fewer parts. Fast installs. ANSI Compliant. 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems

Fewer parts. Fast installs. ANSI Compliant. 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems Fewer parts. Fast installs. ANSI Compliant. 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems 3M DBI-SALA Lad-Saf Flexible Cable Vertical Safety Systems Adding or upgrading your vertical safety

More information

Risk Assessment Form (Qualitative)

Risk Assessment Form (Qualitative) Assessment Form (Qualitative) Project / ocation:..d.a.s WATERS Contract No: RA & Issue No: 008 Prepared by:.r.smit Date: 10/10/16 Signature: ACTIVITY DESCRIPTION: Person (s) at risk: General Ground works

More information

Work Activity (e.g. Road Work): Work Location:.

Work Activity (e.g. Road Work): Work Location:. Working with Cranes Work Activity (e.g. Road Work): Work Location:. GENERAL INFORMATION Hinchinbrook Shire Council Lannercost Street Ingham Qld, 4850 ABN 46 291 971 168 Ph: 47764610 All personnel conducting

More information

Click to edit Master title style. Fall Protection for the Construction Industry Webinar 04/30/2014

Click to edit Master title style. Fall Protection for the Construction Industry Webinar 04/30/2014 Click to edit Master title style Fall Protection for the Construction Industry Webinar 04/30/2014 Webinar Rules Please mute your computer sound Please mute your phones Please do not put your phones on

More information

CPWR - The Center for Construction Research and Training. Fall Hazard Identification and Control Audit of the Aria Building. City Center Project

CPWR - The Center for Construction Research and Training. Fall Hazard Identification and Control Audit of the Aria Building. City Center Project CPWR - The Center for Construction Research and Training Fall Hazard Identification and Control Audit of the Aria Building City Center Project Las Vegas, Nevada September, 2008 Submitted by Mark Fullen

More information