Report on OSU Opto-Pack Prototypes
|
|
- Betty Fowler
- 5 years ago
- Views:
Transcription
1 Report on OSU Opto-Pack Prototypes K.K. Gan The Ohio State University June 11, 2001 K.K. Gan ATLAS Opto-Pack Review 1
2 Outline Introduction Result on VCSEL opto-pack prototypes Result on PIN opto-pack prototypes Result on temperature cycling Result on test with opto-boards Production Plan Conclusions K.K. Gan ATLAS Opto-Pack Review 2
3 OSU Design connector concept design use precisely fabricated cap and base for alignment simple two-piece design for mass production cap holes for fibers base deposit gold traces for wire bonding, VCSEL and PIN placements K.K. Gan ATLAS Opto-Pack Review 3
4 VCSEL Opto-Pack K.K. Gan ATLAS Opto-Pack Review 4
5 PIN Opto-Pack K.K. Gan ATLAS Opto-Pack Review 5
6 produced caps and bases with rounded corners using machinable ceramic material tested: aluminum silicate and macor difficult to obtain consistent precision! redesign base with square corners for ease of fabrication by Hybrid-Tek alumina sheet ground to proper thickness and cut into strips strips cut into bases by American Dicing can produce bases with precision within specification 3D traces have good connectivity (~ 94%)! fabricate cap with Ultem (polyetherimide) for radiation tolerance (10 Grad) Cap and Base Prototypes use manual micro mold injection to save development time can fabricate ~ 10 caps per hour K.K. Gan ATLAS Opto-Pack Review 6
7 VCSEL Base Width 40 σ = 5.6 µ m 30 Count µm Width (mm) accept ~ 90% of bases K.K. Gan ATLAS Opto-Pack Review 7
8 VCSEL Placement VCSEL needs to be placed with a precision of 10 µm! use precisely fabricate jig precision base slot slightly larger than base precisely located pocket for VCSEL pocket slightly larger than VCSEL! 3 contributions to placement uncertainty! 12 out 18 bases fabricated satisfy power coupling spec.! new VCSEL placement scheme K.K. Gan ATLAS Opto-Pack Review 8
9 New VCSEL Placement Scheme measure location of pin in cap mold using comparator! place VCSEL at expected fiber location put base on comparator move cross-hair to expected fiber location based on measured width move VCSEL to cross-hair with micro-manipulator operation time: ~ 5 minutes expect more precise pin location with CMM measurement! should further improve coupled power K.K. Gan ATLAS Opto-Pack Review 9
10 Cap Fabrication Mold K.K. Gan ATLAS Opto-Pack Review 10
11 Fiber Placement Jig K.K. Gan ATLAS Opto-Pack Review 11
12 Cap with Precisely Fabricated Cavity K.K. Gan ATLAS Opto-Pack Review 12
13 Base with VCSEL K.K. Gan ATLAS Opto-Pack Review 13
14 Completed VCSEL Opto-Pack 1 mm K.K. Gan ATLAS Opto-Pack Review 14
15 Coupled VCSEL 10 ma Power (uw) 500 specification Base all VCSEL opto-packs have coupled power well above spec. K.K. Gan ATLAS Opto-Pack Review 15
16 Coupled VCSEL Power vs Usage 1500 power (uw) specification cap1 cap Trial caps can be used multiple times K.K. Gan ATLAS Opto-Pack Review 16
17 Coupled VCSEL Power vs Usage 1500 power (uw) specification Base same cap gives good power on 31 bases! cap is reusable and inter-changeable K.K. Gan ATLAS Opto-Pack Review 17
18 VCSEL Waveform VCSEL opto-pack has fast rise and fall times K.K. Gan ATLAS Opto-Pack Review 18
19 Temperature Cycling 10 VCSEL opto-packs were temperature cycling: ~ 300 cycles between C and 60 0 C! no degradation observed K.K. Gan ATLAS Opto-Pack Review 19
20 PIN Opto-pack Responsivity Responsivity specification Trial PIN opto-pack responsivity is above spec. K.K. Gan ATLAS Opto-Pack Review 20
21 BER of Opto-packs on Opto-board opto-packs can run with low PIN current K.K. Gan ATLAS Opto-Pack Review 21
22 disadvantages advantages: Pro and Con of OSU Design need to fabricate more packages extra time: 2000 caps x 10 min = 2 months of manpower limited number of PIN/VCSEL per package to reduce loss select VCSEL opto-packs of similar coupled power for appropriate I set opto-board without 21 long fibers is much easier to handle cure epoxy on opto-board in oven without fibers for die replacement cap with fibers can be attached to package at end of module assembly K.K. Gan ATLAS Opto-Pack Review 22
23 Production Plan can transfer technology to any interested institution OSU will provide jigs manpower need assuming 30 minutes per VCSEL or PIN! need 1.5 manpower-year to fabricate 3000 packages K.K. Gan ATLAS Opto-Pack Review 23
24 Summary on OSU Opto-pack Prototype OSU prototype program successfully completed can fabricate VCSEL opto-packs with good coupled power can fabricate PIN opto-packs with good responsivity opto-packs can run at low PIN current remountable caps offer maximum flexibility in opto-board assembly and repair K.K. Gan ATLAS Opto-Pack Review 24
Biconic Connectors and Accessories
Phone 800/426 8688 Fax 800/626 0329 3 Biconic Connectors and Accessories The Biconic connector is a conical connector widely used throughout the telecommunications industry. Biconic couplings and attenuators
More informationThis document will provide detailed specifications, a bill of materials (BOM), and assembly instructions for the Official Competition Field.
This document will provide detailed specifications, a bill of materials (BOM), and assembly instructions for the Official Competition Field. Please note that this field utilizes the VEX IQ Challenge Field
More informationCHANGE RECORDS TABLE OF CONTENTS
CHANGE RECORDS Ed./Rev. Date Verified and approved by Description Writer 1 12/31/2015 WY / LLR Initial Document FS 2 02/26/2016 FS / LLR - 1.2. : new applicable document added : validation of the mounting
More informationBonding Reliability Testing for Wafer Level Packaged MEMS Devices
Bonding Reliability Testing for Wafer Level Packaged MEMS Devices Michael Shillinger Vice President of Operations Innovative Micro Technology Santa Barbara, CA, USA mjs@imtmems.com October 20, 2011 Innovative
More informationMelin Tool Micro Catalog
MICRO END MILL TOOL CATALOG Micro sized solid carbide end mills & drills Melin Tool Micro Catalog» New Micro 3 Flute Series» Over 3000 MICRO items INSIDE» Expanded manufactering facility & product line
More informationProcedures for operation of the TA Instruments DSC
Procedures for operation of the TA Instruments DSC Purpose and Scope: This document describes the procedures and policies for using the MSE TA Instruments DSC. The scope of this document is to establish
More informationAssembly and measurements of a mechanical prototype of the BIS MDT chamber
ATLAS Internal Note MUON NO 243 9 June 1998 Assembly and measurements of a mechanical prototype of the BIS MDT chamber K. Ekonomou Physics Department, Aristotle University of Thessaloniki, Thessaloniki,
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationFreescale Semiconductor MMA6222AEG ±20/20g Dual-Axis Medium-g Micromachined HARMEMS Accelerometer
Freescale Semiconductor MMA6222AEG ±20/20g Dual-Axis Medium-g Micromachined HARMEMS Accelerometer MEMS Process Review For comments, questions, or more information about this report, or for any additional
More informationSquare Wave TIG 200 TIG WELDING MACHINE
Square Wave TIG 200 TIG WELDING MACHINE Simplicity Without Compromise The Square Wave TIG 200 is a portable TIG and stick welding machine that lets hobbyists, makers, small fabricators and craftsmen explore
More informationMaterials Selection and Design. Kene Mbanisi and Wole Soboyejo Worcester Polytechnic Institute Worcester, MA 01609
Materials Selection and Design Kene Mbanisi and Wole Soboyejo Worcester Polytechnic Institute Worcester, MA 01609 From the Need Statement to Product Specifications First step in design is to formulate
More informationMODEL ANALOG ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.2 TO 100FT OPERATING RANGE ANALOG OUTPUT
MODEL 862-000-200 ANALOG ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.2 TO 100FT OPERATING RANGE ANALOG OUTPUT DOCUMENT NO. 430-007H September 20, 2005 S/N IMAGENEX TECHNOLOGY CORP. 209-1875 BROADWAY
More information5. Tailplane assembly
5. Tailplane assembly Overview This section covers the fitting of your completed tailplanes to the torque tube assembly. Included is the insertion of the TP13 bushes in the inboard rib and the fitting
More informationSpecial square punch with flattened corners
Special square punch with flattened corners Mild steel (St37), plastic and aluminium to 2.0 Punching of burr-free openings 12.7 dia pilot drill 503102 Punch including punch, die, draw stud, counter nut
More informationKNOTLESS SCREEN PRINTING FOR CRYSTALLINE SILICON SOLAR CELLS
KNOTLESS SCREEN PRINTING FOR CRYSTALLINE SILICON SOLAR CELLS 7th Workshop on Metallization Konstanz - October 23, 2017 Y. Zhang 1, L. Zhang 2, L. Jiang 1, L. Song 1, C. Guo 1, V. Dua 1, H. Yang 1, E. Kim
More informationDIY - PC - Interface for Suunto Cobra/Vyper/Mosquito
DIY - PC - Interface for Suunto Cobra/Vyper/Mosquito Summary This document is the distinct consequence of the Spyder/Stinger interface DIY. After having many e-mails concerning the application for the
More informationMODEL DIGITAL ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.5 TO 100FT (0.15 TO 30M) OPERATING RANGE SERIAL OUTPUT
MODEL 863-000-200 DIGITAL ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.5 TO 100FT (0.15 TO 30M) OPERATING RANGE SERIAL OUTPUT DOCUMENT NO. 430-017C April 14, 2005 S/N IMAGENEX TECHNOLOGY CORP. 209-1875
More informationMini Mr.Bulletfeeder by Double-Alpha
Mini Mr.Bulletfeeder by Double-Alpha User Manual Thank you for choosing the Mini Mr.Bulletfeeder by Double-Alpha! This newly designed product will give you years of reliable service. It will make your
More informationROTO-BLOW MOULDING, A ROTATIONAL MOULDING HYBRID
ROTO-BLOW MOULDING, A ROTATIONAL MOULDING HYBRID Alvin Spence, Centro Incorporated Abstract As the rotational moulding industry moves towards the new millennium, it continues to grow and develop at a phenomenal
More informationOutbound Progress Report
Outbound Progress Report 7-11-17 Tank Install The new 20 plus gallon fuel tank is underway. In a matter of weeks we should be getting the first article and placing a first run order. The tank fits like
More informationTable of Contents FIRST 2005 FIRST Robotics Competition Manual: Section 3 The Arena rev B Page 1 of 8
Table of Contents 3 THE ARENA...2 3.1 OVERVIEW...2 3.1.1 Dimensions and Tolerances...3 3.2 PLAYING FIELD...4 3.2.1 Boundaries and Markings...4 3.2.2 Goals...5 3.2.3 Center Goal...5 3.2.4 Tetra Loading
More informationContinental Industries TRANSITION FITTINGS or FAX Visit
Continental Industries TRANSITION FITTINGS 1-800-558-1373 or FAX 1-800-788-1668 Visit www.conind.com ABOUT US Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and
More informationSTEWART-HAAS RACING Stewart-Haas Racing is the title-winning NASCAR Sprint Cup Series team co-owned by three-time Sprint Cup champion Tony Stewart
STEWART-HAAS RACING Stewart-Haas Racing is the title-winning NASCAR Sprint Cup Series team co-owned by three-time Sprint Cup champion Tony Stewart and Gene Haas. The team fields three entries in the elite
More informationBill Williams FMTC Probe Technology Development Group
Slide 1 Expanding Capabilities of Traditional Cantilever Technology To Meet Advanced DRI Fine Pitch Probe Requirements Presenter: Bill Williams, Freescale Semiconductor FMTC Probe Mgr. and Sr. Member Technical
More informationPaint Brush Handle. Julia Carlson Heather Curtin Julia Hamlin. Western Washington University. March 12, 2003
Paint Brush Handle Julia Carlson Heather Curtin Julia Hamlin Western Washington University March 12, 2003 Society of Plastics Engineers Blow Molding Division 2003 Student Design Competition Recycled Paintbrush
More informationB. Assemble the Method-25 sample train with a heated probe/filter.
6/30/2015 VOC Reporting, Inc. Method 25 Heated Controller Operating Instructions. pg. 1 of 5 INSTRUCTIONS FOR EPA METHOD-25 FIELD SAMPLE COLLECTION USING A VRi HEATED PROBE AND FILTER ASSEMBLY Introduction:
More informationCarving a Custom Seat
Carving a Custom Seat Seat Carving your own seat from mini-cell, high-density foam is really quite simple and has proven to be more comfortable than any commercially produced seat and often more reasonably
More informationUser s manual for the SC32 and SC96 form-fitting recording chamber and microdrive systems
User s manual for the SC32 and SC96 form-fitting recording chamber and microdrive systems 1. Description of the chamber system ----------------------------------------- 2-3 2. Description of the microdrive
More informationROTARY AIRLOCK FEEDERS
DRY BULK MATERIAL HANDLING ROTARY AIRLOCK FEEDERS CONCEPT TO COMPLETION STANDARD MODELS The selection of the correct rotary airlock and options is critical to maintain an efficient and reliable plant operation.
More informationArbor Terminator Press Operation Manual For IDT Connectors Order No Engineering No: AM
Arbor Terminator Press Operation Manual For IDT Connectors Order No. 11-20-0815 Engineering No: AM7223-140 Description Operation Maintenance Order No: TM-011200815 Release Date: 03-08-12 UNCONTROLLED COPY
More informationAPPLICATIONS ROV & AUV SEISMIC PRODUCTION SYSTEMS DOWNHOLE JUMPER & CABLE SYSTEMS DRILLING CONTROL
APPLICATIONS ROV & AUV SEISMIC PRODUCTION SYSTEMS DOWNHOLE JUMPER & CABLE SYSTEMS DRILLING CONTROL ROV & AUV PRODUCTS GRE (Glass Reinforced Epoxy) CS-MS 55 & 66 SERIES MINI-CON HUMMER GLOBE-CON ALL-WET
More informationTips on How to Assemble the Persian Scythed Chariot (60 PSN 07 Y) By scott lam
Tips on How to Assemble the Persian Scythed Chariot (60 PSN 07 Y) By scott lam Introduction The war chariot is invented during the Bronze Age circa 1800 B.C. by the nomadic people of Central Asia. It starts
More informationRelease :
Release : 25.01.08 1 Technical datas : Wingspan : 936 mm Lenght : 444 mm Surface : 5.07 dm² Mass : 90g Wing loading : 17.8 g/dm² 2 A quick summary of the design The Nexus 900 is the result of a long research
More informationPOP UP ANCHOR. Part Number Spectrum Lane ~ Missoula MT ~
POP UP ANCHOR Part Number 153169 7100 Spectrum Lane ~ Missoula MT 59808 800.791.8056 ~ www.spectrumproducts.com You have purchased a Spectrum Products Pop Up Lane Rope Anchor. Providing the unit is installed
More informationPRESENTS. Solder & Oven Profiles Critical Process Variables
PRESENTS ubga s Solder & Oven Profiles Critical Process Variables Phone: 949.713.7229 Fax: 949.713.7229 For Information Please Call or E-mail palsrvs@palsrvs.com Member of: PUBLISHED BY Pan Pacific Microelectronics
More informationWe hope you ll enjoy the Drifter as much as we have! Scott DeTray Model Aero Specifications:
We are excited to bring you the Drifter RC airboat. You re probably thinking it doesn t fly so what is Model Aero thinking??? We have always liked RC vehicles of all types and have had a fondness for airboats
More informationTHE MANUFACTURER ADVANTAGE
MICRO END MILL TOOL CATALOG Micro sized solid carbide end mills & drills THE MANUFACTURER ADVANTAGE get to know who makes your micros Melin Tool Micro Catalog»» New Micro 3 Flute Series»» Over 3000 MICRO
More informationGAS DISTRIBUTION PRODUCTS TRANSITION FITTINGS
GAS DISTRIBUTION PRODUCTS TRANSITION FITTINGS CONTINENTAL INDUSTRIES, INC. The Ultimate Connection CONTINENTAL INDUSTRIES, INC. ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, Inc.,
More informationStatic Pins for Cavity Pressure Applications
Static Pins for Cavity Pressure Applications Static pins can be used as an alternative to flush mount sensors for measuring cavity pressure. Advantages of static pins include: Lower cost of sensors and
More informationDX2/DXX Operating Instructions
CHECK LINE BY ELECTROMATIC DX2/DXX Operating Instructions CHECK LINE INSTRUMENTS ELECTROMATIC E Q U I P M E N T C O., I N C. 600 Oakland Ave., Cedarhurst, NY 11516 U.S.A. TEL: 516-295-4300 FAX: 516-295-4399
More information[Title of the course]
As with non-metallic raceway, Hubbell metal raceway is available in a variety of styles. There are 13 metal raceway profiles 8 painted and 5 aluminum for customers to choose from! ALL Hubbell painted metal
More informationFair Winds Boat Repairs, LLC Riberia St. #7 St. Augustine, Fl
Fair Winds Boat Repairs, LLC. 904-669- 6045 134 Riberia St. #7 www.fairwindsboatrepairs.com St. Augustine, Fl 32084 fairwindsboatrepairs@comcast.net INNOVATION ON THE WATER For over 10 years Walker Bay
More informationMULTI TOOLS for Prima Power Turret Punch Presses
Superior Solutions for Sheet Metal Fabricators MULTI TOOLS for Prima Power Turret Punch Presses Ultra IMT3 Fully Indexable MT Ultra IMT8 Fully Indexable MT Ultra UMT-3B Ultra UMT-8A Ultra MT-3BUi Ultra
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More informationSailTrack Installation Instructions. External Track
SailTrack Installation Instructions External Track SH-500 SS SH-401 SS SH-600 SS SH-200B SS SH-200A SS www.tidesmarine.com Before You Begin Your installation will be easier if you move the boom well off
More informationINSTRUCTION MANUAL. Demountable Ice Bath Pools
INSTRUCTION MANUAL Demountable Ice Bath Pools Your icool Demountable Ice Bath Pool is designed to compliment and enhance the many scientifically proven benefits of regular use of the icool Ice Bath Therapy
More informationENGG1960: Introduction to Biomedical Engineering Lectorial Week 12 Solution
ENGG1960: Introduction to Biomedical Engineering Lectorial Week 12 Solution Linear Fits and Tolerances As a junior biomedical engineer, you are required to work out the necessary limits of size for a simplified
More informationTaylorMade Golf Company Reveals M CGB Irons
TaylorMade Golf Company Reveals M CGB Irons Designed to Push the Limits for Maximum Distance and Power in Every Shot, MCGB Features Ultra-Low CG Placement and Remarkably High COR for Powerful and Forgiving
More informationGANTRY CRANES CAPACITIES: SPANS: TRACKS: OPTIONS: Up to 5 tons Up to 30' Steel Fixed or Adjustable
GANTRY CRANES CAPACITIES: SPANS: TRACKS: OPTIONS: Up to 5 tons Up to 30' Steel Fixed or Adjustable Material Handling Solutions For Your Unique Applications Since 1977, Gorbel has been an innovator and
More informationD-PAK Voiding: A Study to Determine the Origins of D-PAK Voiding
As originally published in the SMTA Proceedings D-PAK Voiding: A Study to Determine the Origins of D-PAK Voiding Kim Flanagan and Greg Wade Indium Corporation Clinton, NY Abstract Voiding in bottom termination
More informationService Bulletin 70. Subject: Vertical fin cracks. Applicability: All Sportsman aircraft
Subject: Vertical fin cracks Applicability: All aircraft Issue: Inspection of the vertical fin and aft fuselage bulkheads B and C, repair of vertical fin and bulkheads and reinforcement of vertical fin
More information2005/2006 Snow Ski Technical Manual
2005/2006 Snow Ski Technical Manual Revision: 041215X Contents Introduction by Dave Goode... 3 Attributes... 4 Model Specifications... 4 Snow Ski Terminology... 5 Binding Installation... 6 Binding Mounting
More informationINDEX THE FINITO UNIVERSE BLANKET PLATE COATING PRESS WRAPPING
The Finito Universe INDEX 03 THE FINITO UNIVERSE 04 UNIVERSAL UNDERPACKING 06 BLANKET 08 PLATE COATING 10 PRESS WRAPPING The Finito Universe 3 Printgraph started to manufacture in 2005 and is one of the
More informationHip Block Installation Instructions:
Hip Block Installation Instructions: The instructions that follow are shown for our low profile hip blocks installed in a Storm Chaser M C-1. However, the very same technique can be used for any of our
More informationcooling tube axis upper mod. physics center lower mod. physics center 45 optical package cooling pipe rd point captive nut
309.7 cooling tube axis upper mod. physics center lower mod. physics center 45 optical package cooling pipe 284.0 3rd point captive nut 2.95 deg. optical fiber connector PCB LMT dogleg 30 active radius
More informationPRODUCT TECHNOLOGY / SPECIFICATIONS
PRODUCT TECHNOLOGY / SPECIFICATIONS SUMMER 2018 i500 IRONS POWERFUL PERFORMANCE Key Technologies Hydropearl 2.0 Chrome Finish Forged Maraging Steel face Metal-wood-like face flexing Muscle-back design
More informationA Table Top Wind Tunnel You Can Build
A Table Top Wind Tunnel You Can Build Basic principles of aerodynamics can be studied in the classroom with this simple, inexpensive wind tunnel. All you need to build it is some cardboard boxes, glue,
More informationSCOUT DECK ANCHOR 3 1/4" BONDING SCREW
SCOUT DECK ANCHOR 16" 16" 1" X 4" ANCHOR BOLT (4) 10" 3 1/8" 5" 6" MIN COPPER WIRE TO ATTACH TO BONDING GRID 3 1/4" BONDING SCREW CONCRETE DECK SPECIFICATIONS: THE AQUA CREEK PRODUCTS' SCOUT DECK ANCHOR
More informationPTC INSTRUMENTS 2301 Federal Ave Los Angeles CA Phone: Model 500 Automatic Operating Stand Type 3
The Model 500 automatic operating stand provides constant load, controlled rate-of-descent, and application velocity, through a geared electric motor and braking mechanism that alternately lowers the durometer
More informationFinalizing the DTAG: Implementation and Testing of Design Improvements for Reliability and Availability
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Finalizing the DTAG: Implementation and Testing of Design Improvements for Reliability and Availability K. Alex Shorter
More informationwww.aquaglidekayak.com WORK SPACE AND TOOLS 1. Take care to position yourself in a clean, dry area with good ventilation. For proper curing of adhesives, temperature should remain above 10 C (50 F).
More informationBrixham Archers Arrow Workshop 2015
Brixham Archers Arrow Workshop 2015 Arrow Making Aluminium/Carbon Composite Copyright Brixham Archers LTD Contents Parts of an Arrow Arrow Types (Aluminium, Carbon Composite) Choosing the Right Arrow Spines
More informationXSL-360-5E. UV LED 5 mm TECHNICAL DATA. Absolute Maximum Ratings (T a =25 C) Specifications (If=20mA, T a =25 C) Drawing
XSL-360-5E TECHNICAL DATA UV LED 5 mm Drawing Absolute Maximum Ratings (T a =25 C) Item Symbol Value Unit DC Forward Current I F 25 ma Peak Pulse Forward Current * 1 I FP 100 ma Power Dissipation P D 100
More informationdefenders get specific coaching for their respective positions, goalies require the same attention and guided skill development.
POWER POINT SLIDES ACTIVITIES NOTES Mini-lecture: Over view- 10 RM- p. 1 1. Provide the following overview of the clinic: Rationale: Goaltending is a critical aspect of team play and requires direct &
More information35 TON HYDRAULIC PUNCH WARNING
OPERATORS GUIDE REL-35T-PNC 35 TON HYDRAULIC PUNCH NOTICE Sizes, weights and tool specifications listed in this manual are subject to change without notice. Please consult factory for information and updates.
More informationRF Chip Inductors. Wire-Wound , 0603, 0805, 1008, Pulse Electronics - leading supplier of magnetics for consumer applications
RF Chip Inductors Wire-Wound - 0402, 0603, 0805, 1008, 1206 Pulse Electronics - leading supplier of magnetics for consumer applications Table of Contents The 0402 to 1206 series range of Miniature Chip
More information18. Tailplane torque-tube
18. Tailplane torque-tube Step 1 Fu se lage rear bulkhead Remove the three part templates of the rear bulkhead: an A4 size sheet from Annex A (page 5) and two A3 size sheets from Annex F of the manual,
More informationProject Number: P17453
Multidisciplinary Senior Design Conference Kate Gleason College of Engineering Rochester Institute of Technology Rochester, New York 14623 Project Number: P17453 DRESSER-RAND RECIPROCATING COMPRESSOR TEST
More information1 of 6 16/8/18, 6:07 pm
Trevor Boundy FW: 25 PT-19 - Redesign and Fabrication of Fuselage Stab Mount 1 message Tandy Walker To: Trevor Boundy Wed, Aug 15, 2018
More informationEliminating Gross Leakers by Seal Processing for Lowest Leak Rates per MIL-STD-883 TM 1014 Seal
Eliminating Gross Leakers by Seal Processing for Lowest Leak Rates per MIL-STD-883 TM 1014 Seal MicroCircuit Laboratories LLC Gross Leakers of Hermetic Microelectronic Packages Hermetic packaging is required
More informationF13.11 PARALLEL HINGES F13 PROJECT-OUT WINDOWS AND TOP HUNG WINDOWS
F13 PROJECT-OUT WINDOWS AND TOP HUNG WINDOWS F13.11 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General...F13.11.03
More informationTRAINING PACKAGES
TRAINING PACKAGES 2018 COURSE CONTENT RYCO has developed a series of training programs covering all aspects of fluid connector technology. From competencies for product selection and assembly practices,
More informationOptical-Polymer and Polymer-Clad- Silica-Fiber Data Buses for Vehicles and Airplanes Principles, Limits and New Trends
Optical-Polymer and Polymer-Clad- Silica-Fiber Data Buses for Vehicles and Airplanes Principles, Limits and New Trends Otto Strobel, Daniel Seibl, Jan Lubkoll, Uwe Strauß Optical Transmission Optical Detector
More informationMegan Anderson, QTS Project Engineer. March 8 10, 2011 Hyatt Regency Cincinnati, OH
Megan Anderson, QTS Project Engineer March 8 10, 2011 Hyatt Regency Cincinnati, OH Megan Anderson, QTS Project Engineer 2 Medical devices that are oxygen sensitive must be packaged using equipment that
More informationThe latest automotive systems require innovative leak test methods and fixturing.
Leak Testing Auto Parts The latest automotive systems require innovative leak test methods and fixturing. In the past, automobile manufacturers only required basic forms of leak testing to check standard
More informationTracheostomy Tube Security Device
Tracheostomy Tube Security Device Client: Dr. Timothy McCulloch Advisor : Professor Paul Thompson Leader: Katie Pollock Communicator: Rebecca Clayman BWIG: Kim Safarik BSAC: Paul Fossum Background: Problem
More informationATLAS Pixel Detector Flex Hybrid Assembly Manual
ATLAS Pixel Detector Flex Hybrid Assembly Manual version 1.0 27 September, 2002 1 Introduction 1.1 Purpose This manual describes the equipment, materials and step-by-step procedures to be used in the construction
More informationInstallation of 2 Tier In Line Greeting Card Rack
Installation of 2 Tier In Line Greeting Card Rack Material Sent to Store: Greeting Card Fixtures: 4ft Inline Tier Kit (1 per every 4ft based on planogram) 3ft endcap Tier Kit (will not receive if planogram
More information5/16 MAXFLOW SPOUTS 17/64 MAXFLOW SPOUTS. 5/16 black spout with barbs $0.25 $ /64 white spout without barbs. 5/16 white spout without barbs
FITTINGS The new line of 5/16" Maxflow fittings was specifically designed and developed for maple producers wanting to operate over 25 in-hg (high vacuum). These fittings enable a perfect seal with a vacuum
More informationDETERMINATION OF THE DEPTH OF CLOSED BLIND CRACKS IN NON-METAL CHECK SAMPLES AND TEST PANELS FOR PENETRANT TESTING
DETERMINATION OF THE DEPTH OF CLOSED BLIND CRACKS IN NON-METAL CHECK SAMPLES AND TEST PANELS FOR PENETRANT TESTING Nikolay Kalinichenko 1, Aleksey Kalinichenko 1, Irina Lobanova 1*1, Anna Zaitseva 1, Egor
More informationShiel e d Kite t By B y Sam & Ca C rir King Ore r g e o g n o Kite t m e aker e rs s Retr t e r a e t t2013
Shield Kite By Sam & Cari King Oregon Kitemaker s Retreat 2013 SAIL ASSEMBLY Your pre-cut sail pieces include half-inch seam allowances. This provides enough material to complete a 1/4 inch double rolled
More informationME 472 Engineering Metrology
ME 472 Engineering Metrology and Quality Control Chp 11 - Limits and Limit Ga(u)ges Mechanical Engineering University of Gaziantep Dr. A. Tolga Bozdana Assistant Professor Various Types of Limit Gauges
More informationMoai Bike Rack Heavy Duty Submittal Sheet. Materials: 2.0 Schedule 40 Pipe (2.375 OD) Finishes: Capacity: Mount Options: Setbacks: 2 Bikes
Submittal Sheet Materials: 2.0 Schedule 40 Pipe (2.375 OD) Finishes: Galvanized An after fabrication hot dipped galvanized finish is available. Powder Coat Our powder coat finish assures a high level of
More informationEverything you need to know about flatteners and levelers for coil processing
http://www.thefabricator.com/xp/fabricator/articles/fabricating/fabricating03/02web56 9.xml Provided by: Welded Tube Pros LLC, www.weldedtubepros.com Doylestown, OH. Tel: 330-658-7070 Email contact for
More information602 STRINGING MACHINE OWNER'S MANUAL
PROGRESSION 602 STRINGING MACHINE OWNER'S MANUAL AL Issue 1- April 2000 Copyright 2000 GAMMA Sports - All Rights Reserved PROGRESSION 602 STRINGING MACHINE TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...
More informationMPM426W/436W Submersible Level Transmitter
/436W Submersible Level Transmitter Features Full sealed stainless steel construction for submersible part; sensor and amplifier circuit are all in the sealed housing; protection class IP68; Aluminum-alloy
More informationMitsubishi Heavy Industries Technical Review Vol. 53 No. 4 (December 2016)
Completion of Joyo Experimental Fast Reactor Upper Core Structure Replacement - Development of Fast Reactor Core Internal Equipment Replacement method - 65 MASAHIDE HARA *1 JUNYA TANAKA *2 HIROYOSHI OKAZAKI
More informationMS52XX-C&T SMD Pressure Sensor
1, 4, and 7 bar absolute pressure range Piezoresistive silicon micromachined sensor Surface mount 6.2 x 6.4 mm LCP plastic cap for easy connection Uncompensated Optional trimmed offset Low noise, high
More informationINSTRUCTION GUIDE S-WORKS ROAD CARBON CRANKSET (Carbon and Alloy OSBB cups)
INSTRUCTION GUIDE S-WORKS ROAD CARBON CRANKSET (Carbon and Alloy OSBB cups) THIS BRIEF INSTRUCTION GUIDE CONTAINS IMPORTANT INFORMATION. PLEASE READ CAREFULLY AND STORE IN A SAFE PLACE. Congratulations!
More informationARM & CHEST FEATURES BAUER REACTOR 9000 THE HOME OF HOCKEY. Price 699,95 NEW! Item Type Size Color
ARM & CHEST BAUER REACTOR 9000 M XL white / navy / blue No. 1045852 Price 699,95 Designed for mobility with pro protection Overlap construction in shoulder area eliminates protection gaps 37.5 Technology
More informationContinental Industries STEEL SERVICE TEES or FAX Visit
Continental Industries STEEL SERVICE TEES 1-800-558-1373 or FAX 1-800-788-1668 Visit www.conind.com ABOUT US Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and
More informationAutomating Injection Molding Simulation using Autonomous Optimization
Automating Injection Molding Simulation using Autonomous Optimization Matt Proske, Rodrigo Gutierrez, & Gabriel Geyne SIGMASOFT Virtual Molding Autonomous optimization is coupled to injection molding simulation
More informationMade in U.S.A. Narrow-U Bike Rack Heavy Duty Submittal Sheet. Materials: Finishes: Mount Options: Setbacks:
Submittal Sheet Materials: 2 Schedule 40 Steel Pipe (2.375 OD) Finishes: Galvanized An after fabrication hot dipped galvanized finish is available Powder Coat Our powder coat finish assures a high level
More informationNajo Backboards. by Ferno. Users Manual. February 2006 GLO Pub. No Najo RediBoard. Najo Lite. Najo. Najo RediHold. RediWide.
Users Manual Najo RediWide Najo RediBoard Najo RediHold Najo Lite Backboard Najo Sports Backboard Najo Disaster Board Najo Water & Rescue Backboard Najo Mega 1000 Backboard Najo Backboards by Ferno February
More informationBasic Install Guide. Parts: 1 P a g e
Basic Install Guide Parts: 1 P a g e Step One: Remove all panels and components from boxes. Step Two: Carefully unroll your turf. Be sure not to cut the turf when removing from protective plastic. The
More informationPlans and Instructions to build a folding reflector oven
Plans and Instructions to build a folding reflector oven Kayak2go.com also has folding kayak plans available for purchase. The low cost and ease of construction make the folding kayaks a great youth group
More informationFinal Assembly Instructions Bikes with 16 Wheel Size
Final Assembly Instructions Bikes with 16 Wheel Size Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationTri-Better Detailed Design Review
Tri-Better Detailed Design Review Designers: Michael Kurvach Nathaniel Morefield Ryan Wilson Cody Woods Guide: Dr. Richard Lux Project Overview The goal of this project is to create a shoe and pedal which
More informationdumont Minute Man Broaches
Catalog K dumont Minute Man Broaches Standard and Special Broaches Keyway Broaches and Sets Internal Hole and Surface Broaches The dumont Company, Greenfield, Massachusetts www.dumont.com The dumont Company
More informationMounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser
Mounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser The RoboFocus unit can be mounted on the Meade MicroFocuser, commonly found on the LX-200/400 series. The RF folks point to this URL as a
More information