Compression Fittings
|
|
- Claud Blake Gaines
- 5 years ago
- Views:
Transcription
1 Advantages o flaring, soldering or other preparation of tubing necessary to assemble. This economical fitting is readily available in a broad selection of styles. anufactured from CA 360, CA 35 or CA 377 brass. Specifications isted with Underwriter s aboratories for flammable liquid. Compression fittings meet functional requirements of SAE J-51, ASA and ASE. Refer to list of U listed fittings on page 6 for specific configurations. Applications Use with copper, aluminum, and Parflex thermoplastic tubing as shown on page 3. ot recommended for steel tubing. anufactured for low and medium pressure tubing connection work where excessive vibration or tube movement is not involved. ot recommended for application using gaseous media. Fitting Siz ize Turns required to seal from hand-tigh and-tight t Tube Siz ize 60C 60PT with with soft t thermoplasti hermoplastic metal tubing t tubin ubing 1 1-1/ / 8 3 3/16 1-1/ 1/ 1-1/ 5 5/16 1-1/ 6 3/ 8-1/ 8 1/ -1/ 10 5/ 8-1/ 1 3/ -1/ 1 7/ 8-1/ Working Pressure Ranges Temperature and type of tubing used are important factors. However, the following table is a good guide for proper selection. Temperature 73 F. For thermoplastic tubing, see manufacturers recommendation for pressure range. Temperature Ranges From -65 to +50 F with soft metal tubing. For thermoplastic tubing, see manufacturers recommendation for tubing temperature range. Tube O.. PSI (Inches Inches) Tube Wall ( (Inches Inches) 00 1/ / / / / / / / / omenclature Part numbers are constructed from symbols that identify the style and size of the fitting. The first series of numbers and letters identifies the style and type fitting. The second series of numbers describes the size. Example: 69 C 6 Extrusion () Forging (1) ale Elbow Compression 3/8" (6/16) Tube O.. 1/" (/16) Pipe Thread ote: To order compression assemblies with long nuts, add the letter after the letter C. Example: 6C- with short nut,6c- with long nut Vibration Fair resistance to vibration or tube movement, depending on applications involved. Use long nut for additional resistance to vibration. Assembly Instructions 1. Slide nut, then sleeve onto tubing. The thread end of the nut must face out.. Insert the tube into the fitting. Be sure the tube is bottomed on the fitting shoulder. 3. Assemble nut to body, and tighten hand-tight. Then follow the number of wrench turns as indicated in the following table. Order By part number and name. Sizes Tube sizes are determined by the numbers of sixteenths of an inch in the tube O.. Special Fittings Fitting configurations and/or sizes other than those shown in the catalog can be furnished. It is suggested that a print or sketch be submitted with the inquiry. Special U stamped fittings are available. Please consult price list. Pricing Only items priced in current supplementary price list P3501 are carried in stock. Price and delivery for non-stock items furnished on request for specified quantity. 38 Parker Brass Products ivision Otsego, ichigan
2 Sleeve 60C Ref. SAE PART TUBE O. SIZE A 60C- 1/ C-3 3/ C- 1/ C-5 5/ C-6 3/ C-7 7/ C-8 1/ C-10 5/ C-1 3/ C-1 7/ A elrin sleeve 60PT PASTIC PART TUBE TUBE O. WA WA A 60PT- 1/ PT-5 5/ PT-6 3/ PT-8 1/ PT-10 5/ PT-1 3/ A ut 61C Ref. SAE PART TUBE STRAIGHT C O. SIZE THREA HEX 61C- 1/8 5/16-3/ C-3 3/16 3/8-7/ C- 1/ 7/16-1/ C-5 5/16 1/- 9/ C-6 3/8 9/16-5/ C-7 7/16 5/8-11/ C-8 1/ 11/ / C-10 5/8 13/ / C-1 3/ / C-1 7/8 1-1/ / ong nut 61C Ref. SAE PART TUBE STRAIGHT C O. SIZE THREA HEX 61C- 1/ 7/16-1/ C-5 5/16 1/- 9/ C-6 3/8 9/16-5/ C-8 1/ 11/ / C-10 5/8 13/ / C-1 3/ / Parker Brass Products ivision Otsego, ichigan
3 Union 6C Ref. SAE BA PART TUBE STRAIGHT C FOW O. SIZE THREA HEX IA. 6C- 1/8 5/16-5/ C-3 3/16 3/8-3/ C- 1/ 7/16-7/ C-5 5/16 1/- 1/ C-6 3/8 9/16-9/ C-7 7/16 5/8-5/ C-8 1/ 11/ / C-10 5/8 13/ / C-1 3/ C-1 7/8 1-1/ / Union Reducers 6C Ref. SAE BA 1 1 FOW PART TUBE TUBE STRAIGHT STRAIGHT C FOW O. SIZE SIZE THREA THREA HEX IA. 6C--3 3/16 1/ 3/8-7/16-7/ C-6-1/ 3/8 7/16-9/16-9/ C-8-6 3/8 1/ 9/16-11/ / C /8 5/8 9/16-13/ / Bulkhead union 6CBH PART TUBE STRAIGHT C FOW O. SIZE THREA HEX IA. 6CBH- 1/ 7/16-9/ CBH-6 3/8 9/16-11/ Brass insert 63PT (For industrial grade plastic tubing) PART TUBE TUBE O.. O. O.. WA O.. 63PT--16 1/ PT--3 1/ PT--3 1/ PT-3-5 3/ PT-3-0 3/ PT--0 1/ PT--6 1/ PT-5-0 5/ PT-5-6 5/ PT-6-6 3/ PT-8-6 1/ PT / For plastic tubing erlin Sleeve 60PT and Brass Insert 63PT converts standard compression fittings for use with industrial grades of thermoplastic tubing. O.. 0 Parker Brass Products ivision Otsego, ichigan
4 Female connector 66C Ref. SAE BA PART TUBE PIPE STRAIGHT C FOW O. SIZE THREA THREA HEX IA. 66C-- 1/8 1/8 5/16-9/ C-3-3/16 1/8 3/8-9/ C-3-3/16 1/ 3/8-11/ C-- 1/ 1/8 7/16-9/ C-- 1/ 1/ 7/16-11/ C-5-5/16 1/8 1/- 9/ C-5-5/16 1/ 1/- 11/ C-6-3/8 1/8 9/16-9/ C-6-3/8 1/ 9/16-11/ C-6-6 3/8 3/8 9/16-13/ C-6-8 3/8 1/ 9/ C-7-6 7/16 3/8 5/8-13/ C-8-1/ 1/ 11/ / C-8-6 1/ 3/8 11/ / C-8-8 1/ 1/ 11/ C /8 1/ 13/ ale connector 68C Ref. SAE BA PART TUBE PIPE STRAIGHT C FOW O. SIZE THREA THREA HEX IA. 68C-- 1/8 1/8 5/16-7/ C-3-3/16 1/8 3/8-7/ C-3-3/16 1/ 3/8-9/ C-- 1/ 1/8 7/16-7/ C-- 1/ 1/ 7/16-9/ C--6 1/ 3/8 7/16-11/ C--8 1/ 1/ 7/16-7/ C-5-5/16 1/8 1/- 1/ C-5-5/16 1/ 1/- 9/ C-6-3/8 1/8 9/16-9/ C-6-3/8 1/ 9/16-9/ C-6-6 3/8 3/8 9/16-11/ C-6-8 3/8 1/ 9/16-7/ C-7-7/16 1/ 5/8-5/ C-8-1/ 1/ 11/ / C-8-6 1/ 3/8 11/ / C-8-8 1/ 1/ 11/16-0 7/ C /8 3/8 13/ / C /8 1/ 13/ / C /8 3/ 13/ / C-1-8 3/ 1/ C-1-1 3/ 3/ / C-1-1 7/8 3/ 1-1/ / Union tee 16C-6C Ref. SAE BA PART TUBE STRAIGHT FOW O. SIZE THREA IA. 16C- 1/8 5/ C-3 3/16 3/ C- 1/ 7/ C- 1/ 7/ C-5 5/16 1/ C-6 3/8 9/ C-8 1/ 11/ C-10 5/8 13/ C 6C 1 Parker Brass Products ivision Otsego, ichigan
5 Union tee 16C-6C Combination Sizes Ref. SAE BA 1 3 FOW PART TUBE TUBE TUBE FOW O. SIZE SIZE SIZE IA. 16C-6-- 3/8 1/ 1/ C /8 3/8 1/ C / 1/ 3/ Union elbow 165C-65C Ref. SAE BA PART TUBE STRAIGHT FOW O. SIZE THREA IA. 165C- 1/8 5/ C-3 3/16 3/ C- 1/ 7/ C- 1/ 7/ C-5 5/16 1/ C-6 3/8 9/ C-7 7/16 5/ C-8 1/ 11/ C-10 5/8 13/ C-1 3/ C 65C Compression gage tee 168C PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA 1 IA. 168C-- 1/ 1/8 7/ , ale elbow 169C-69C Ref. SAE 0600 BA PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA IA. 69C-- 1/8 1/8 5/ C-3-3/16 1/8 3/ C-3-3/16 1/8 3/ C-3-3/16 1/ 3/ C-- 1/ 1/8 7/ C-- 1/ 1/8 7/ C-- 1/ 1/ 7/ C-- 1/ 1/ 7/ C--6 1/ 3/8 7/ C-5-5/16 1/8 1/ C-5-5/16 1/8 1/ C-5-5/16 1/ 1/ C-5-5/16 1/ 1/ C-5-6 5/16 3/8 1/ C-6-3/8 1/8 9/ C-6-3/8 1/8 9/ C-6-3/8 1/ 9/ C-6-3/8 1/ 9/ C-6-6 3/8 3/8 9/ C-6-6 3/8 3/8 9/ C-6-8 3/8 1/ 9/ C-7-6 7/16 3/8 5/ C-8-1/ 1/ 11/ C-8-6 1/ 3/8 11/ C-8-8 1/ 1/ 11/ C /8 1/ 13/ C-1-8 3/ 1/ C-1-1 3/ 3/ C 69C Parker Brass Products ivision Otsego, ichigan
6 Female elbow 170C-70C Ref. SAE BA PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA IA. 170C-- 1/8 1/8 5/ C-3-3/16 1/8 3/ C-- 1/ 1/8 7/ C-- 1/ 1/8 7/ C-- 1/ 1/ 7/ C-6-3/8 1/ 9/ C-6-6 3/8 3/8 9/ C-7-7/16 1/ 5/ C-8-6 1/ 3/8 11/ C 70C ale run tee 171C PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA IA. 171C-- 1/8 1/8 5/ C-3-3/16 1/8 3/ C-- 1/ 1/8 7/ C-- 1/ 1/ 7/ C-6-3/8 1/ 9/ ale branch tee 17C Ref. SAE 0605 BA PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA IA. 17C-- 1/8 1/8 5/ C-3-3/16 1/8 3/ C-- 1/ 1/8 7/ C-- 1/ 1/ 7/ C-6-3/8 1/8 9/ C-6-3/8 1/ 9/ C-6-6 3/8 3/8 9/ C-8-6 1/ 3/8 11/ Adapter tee 176C PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA 1 IA. 176C-- 1/ 1/8 7/ Female branch tee 177C PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA IA. 177C-- 1/ 1/8 7/ Parker Brass Products ivision Otsego, ichigan
7 5 elbow 179C Compression to male pipe PART TUBE PIPE STRAIGHT FOW O. SIZE THREA THREA IA. 179C-- 1/ 1/8 7/ C-- 1/ 1/ 7/ C-6-3/8 1/8 9/ C-6-3/8 1/ 9/ C-6-6 3/8 3/8 9/ C-8-6 1/ 3/8 11/ Seal plug 639C PART TUBE STRAIGHT C O. SIZE THREA HEX 639C- 1/ 7/16-7/ Straight through tank fitting 68C PART TUBE PIPE STRAIGHT C FOW O. SIZE THREA THREA HEX IA. 68C-3-3/16 1/8 3/8-7/ C-6-6 3/8 3/8 9/16-11/ C-8-8 1/ 1/ 11/16-0 7/ Parker Brass Products ivision Otsego, ichigan
Barbed Fittings. The World Standard. Dubl-Barb Fittings. Hose Barb Fittings. Compact One-piece Economical Reusable Use with Polyethylene Tubing
Barbed Fittings zfc05 ubl-barb Fittings Compact One-piece Economical Reusable Use with Polyethylene Tubing Hose Barb Fittings All Brass Construction Straight and etric Threads Beaded & Standard Hose Barbs
More informationIndustrial Compression Style Fittings. Compression Fittings Compress-Align Fittings Brass Metric Compression Poly-Tite Fittings Hi-Duty Fittings
Industrial Compression Style Fittings Compression Fittings Compress-lign Fittings rass etric Compression oly-tite Fittings i-uty Fittings arker annifin Corporation Fluid System Connectors Otsego, I Industrial
More informationHose Barb Fittings HOSE CLAMP 3/16" 97 HC-3 1/4" 1/4" 97 HC-3 1/4" 5/16" 97 HC-6 1/4" 3/8" 97 HC-6 1/8" 1/2" 97 HC-8 1/8" 5/8" 97 HC-12 1/8"
atalog 3501E ATERIAS OF OSTRUTIO FITTIS: O-RI: BRASS FUOROARBO OEATURE EXAPE: 125HB-6-4 125 HB ATTRIBUTE: BARB TO AE BARB 6 3/8 I.. 4 1/4 PTF/PTF APPIABE TUBE TUBE ATERIA: RUBBER, PH I..: 1/4, 5/16, 3/8,
More informationIndustrial Compression Style Fittings
Industrial Compression Style Fittings Compression Fittings Compress-lign Fittings rass etric Compression oly-tite Fittings i-uty Fittings arker annifin Corporation Fluid System Connectors Otsego, I Industrial
More informationPART NO. UPC DESCRIPTION QTY LBS
24 Iron Pipe Fittings Product Applications For use with brass, copper or iron pipe. Designed for low and medium pressure pipe line connections. Typically used in water, grease, fuels, LP and natural gas,
More informationIntru-lok Flareless Bite Type Fittings
Intru-lok Flareless Bite Type Fittings 4300 atalog Flareless Bite Type Fittings Nuts, Ferrules, Inserts BIP Knurled Nut BI2 Nut BTI2 Nut and Ferrule TI2 Ferrule TIP Expander / Insert T23UI Insert HBI2
More informationCOMPRESSION TUBE FITTINGS
COMPRESSION TUBE FITTINGS 1/16 THROUGH 2 2 MM THROUGH 50 MM LET-LOK TUBE FITTINGS DESCRIPTION The HAM-LET GROUP has produced high quality tube and pipe LET-LOK HOW DOES IT WORK? A HAM-LET has gained an
More informationContinental Industries STEEL SERVICE TEES or FAX Visit
Continental Industries STEEL SERVICE TEES 1-800-558-1373 or FAX 1-800-788-1668 Visit www.conind.com ABOUT US Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and
More informationprecision pipe fittings
Precision Pipe Fittings 1 8 to 1 sizes 316 stainless steel, brass, and exotic materials NPT threads HOKE PO Box 4866 Spartanburg, SC 29305-4866 Phone (864) 574-7966 Fax (864) 587-5608 www.hoke.com Sales-hoke@circor.com
More informationCOMPRESSION TUBE FITTINGS
COMPRESSION TUBE FITTINGS 1/16 THROUGH 2 2 MM THROUGH 50 MM LET-LOK TUBE FITTINGS DESCRIPTION The HAM-LET GROUP has produced high quality tube and pipe fittings in various materials for high pressure applications
More informationCOMPRESSION TUBE FITTINGS 1/16 THROUGH 2 -INCH, 2 MM THROUGH 50 MM-METRIC
1/16 THROUGH 2 -INCH, 2 MM THROUGH 50 MM-METRIC LET-LOK TUBE FITTINGS DESCRIPTION HAM-LET LET-LOK HOW DOES IT WORK? HAM-LET LET-LOK LET-LOK LET-LOK HAM-LET LET-LOK 1 4 3 2 4 Tube 1 2 3 1 2 3 4 6 LET-LOK
More informationTOTALINE BRASS FITTINGS
LONG NUT SHORT NUT & SHORTER NUT TO CAP NUT MALE CONNECTOR WT. PER LONG NUT 1/8 1.20 4000 25 P806-N2-2 3/16 1.70 2500 25 P806-N2-3 1/4 3.44 1400 50 P806-N2-4 5/16 4.60 900 25 P806-N2-5 3/8 7.90 550 50
More informationINSERT FITTINGS INSERT FITTINGS
Insert Tee Insert x Female Tee Insert Elbow Insert x Male Elbow Insert Coupling Insert x Male Adapter Insert x Female Adapter Insert Plug POLY and NYLON FITTINGS For use with Poly Tubing Fitting 1/2 3/4
More informationContinental Industries TRANSITION FITTINGS or FAX Visit
Continental Industries TRANSITION FITTINGS 1-800-558-1373 or FAX 1-800-788-1668 Visit www.conind.com ABOUT US Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and
More informationCOPPER TUBE COPPER AND BRASS FITTINGS SOFT DRAWN COPPER CAPILLARY COUPLER CAPILLARY NOMINAL OD WALL ROLL (M) R410A STOCK CODE CAA0020 1/
COPPER TUBE SOFT DRAWN COPPER NOMINAL OD INCHES MM WALL ROLL (M) CAA0020 1/4 6.4 0.81 18 CAA0040 3/8 9.5 0.81 18 CAA0060 1/2 12.7 0.81 18 CAA0080 5/8 15.9 0.81 18 CAA0100 5/8 15.9 1.02 18 CAA0120 3/4 19.1
More informationGAS DISTRIBUTION PRODUCTS TRANSITION FITTINGS
GAS DISTRIBUTION PRODUCTS TRANSITION FITTINGS CONTINENTAL INDUSTRIES, INC. The Ultimate Connection CONTINENTAL INDUSTRIES, INC. ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, Inc.,
More informationTwo Ferrule Tube Fittings 316 stainless steel ranging from 1/8" to 1" (6mm to 25mm) O.D.
Two errule Tube ittings 316 stainless steel ranging from 1/8" to 1" (6mm to 25mm) valve & fitting www.veelok.com Introduction Vee-Lok tube fittings are designed to provide a leak-free connection and applied
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationPN LINE. Technical remarks PN 11 PN 13 PN 14 PN 15 PN 17 PN 18 PN 20 PN 23 PN 25 PN 26 PN 27 PN 28 PN 29 PN 37 PN 38 PN 39 PN 40 PN 43 PN 10 8_9 10_12
PN LINE PN 11 PN 13 PN 14 PN 15 PN 17 PN 18 PN 20 PN 23 PN 25 PN 26 PN 27 PN 28 PN 29 PN 37 PN 38 PN 39 PN 40 PN 43 PN 10 Technical remarks PN 11 PN 13 PN 14 PN 15 PN 17 PN 18 PN 20 PN 23 PN 25 PN 26 PN
More information// ADapters GUIDelines
// ADapters GUIDelines ADAPTER SELECTION Selection of an appropriate ALFAGOMMA adapter for a given application depends on the fluid system operating parameters listed below and the tube material and wall
More informationscrew fittings - nickel plated brass series SC
screw fittings - nickel plated brass series SC SC SCC SC SC SC SC SC SCC SC SC SC SCC SC SC SC2C SC2 SC2 SC SC3 SC3 SC0 SC design screw fitting with swivel nut connection 1/"...1/2" optionally cylindrical
More informationFITTINGS THREAD LUBRICANTS. Fittings 20,000 PSI
Jetstream offers a wide variety of fittings with various connection types to fit your 20,000 psi application needs. The standard connection types, Type M, MP, and MP Tube lance, are available in standard
More informationHigh Pressure Equipment Taper Seal Valves, Fittings and Tubing
igh quipment Taper Seal Valves, ittings and Tubing 0,000 and,000 psi service igh quipment Company has developed the Taper Seal line of products to assure safe and easy plumbing through,000 psi. These needle
More informationSection 3- Repair and Calibration Procedures
Section 3- Repair and Calibration Procedures 1. Refrigerant Removal Procedures 2. Scale/PC Board Recalibration Procedure 3. PC Board Configuration Procedure of AR400 4. Scale Tare Procedure 5. Gauge Calibration
More informationPVC FASTTAP SADDLES for IPS Mains. Main Size OUTLET 1 FPT 3/4 CTS (7/8 OD) COMPRESSION 1 CTS (1 1/8 OD) COMPRESSION 3/4 IPS COMPRESSION
PVC FASTTAP SADDLES PVC FASTTAP SADDLES for IPS Mains THE ULTIMATE CONNECTION OUTLET 3/4 IPS FEMALE SLIP OR 1 IPS MALE SLIP SOLVENT WELD 1 IPS FEMALE SLIP SOLVENT WELD 3/4 MPT 1 MPT 3/4 FPT MAIN 13/16
More informationMODEL MN-PWV PRESSURIZED WATER VESSEL ASSEMBLY OPERATING MANUAL
MODEL MN-PWV PRESSURIZED WATER VESSEL ASSEMBLY OPERATING MANUAL Prepared by CR Manning Edited by SC Woidtke Rev August 22, 2011 PRESSURIZED WATER VESSEL OPERATING MANUAL 1. Background 1.1 The Pressurized
More informationFittings, Materials and Tubing Guide. Instrumentation Products
Fittings, Materials and Tubing Guide Fittings, Materials and Tubing Guide Instrumentation Products MPI Medium Fittings Introduction Hannifin Fittings are engineered and manufactured to provide secure,
More informationTorque Specifications
SENR3130-10 Torque Specifications All Caterpillar Products S/N From the library of Barrington Diesel Club CONTENT General Information 01/07/2005 Introduction to Torque 01/07/2005 Torque-Turn 01/07/2005
More informationTANK MATE INCLUDES: TOOLS REQUIRED: CONRADER VALVES 3/4 WRENCH **TUBING CUTTERS TEE PETCOCK TEE ASSEMBLY 8 FOOT NYLON TUBING
CONRADER VALVES TANK MATE AUTOMATIC DRAIN VALVE INSTALLATION KIT INCLUDES: TEE PETCOCK TEE ASSEMBLY 8 FOOT NYLON TUBING WV-1 DRAIN VALVE TOOLS REQUIRED: 3/4 WRENCH **TUBING CUTTERS ** NEEDED TO CUT METAL
More information40K TLX Nozzles 40K TLX
40K TLX Nozzles 40K TLX Application/Features: These nozzles are designed specifically for use with Flex or Rigid Lances having male Autoclave-type High Pressure threads. The TLX Nozzle features a special
More informationSCHRADER TANK VALVES FOR USE IN AIR BLADDER APPLICATIONS, BICYCLE SUSPENSION SYSTEMS, TELECOMMUNICATIONS, WATER STORAGE SYSTEMS, ETC.
SCHRADER TANK VALVES FOR USE IN AIR BLADDER APPLICATIONS, BICYCLE SUSPENSION SYSTEMS, TELECOMMUNICATIONS, WATER STORAGE SYSTEMS, ETC. Demand an authentic Schrader valve built by the company that set the
More informationPrestolok PLM Metal Push-to-Connect Fittings
Prestolok PM Metal Push-to-Connect ittings To meet your technical and environment requirements, Parker s Prestlok PM fittings offers the robustness, reliability and resistance to industrial fluids for
More informationFITTING IDENTIFICATION AMERICANT THREAD TYPES APPENDIX ALFAGOMMA // APPENDIX. Dash numers. NPTF (National Pipe Tapered Fuel)
// FITTINGS GUIDelines FITTING IDENTIFICATION numers Most fluid piping system sizes are measured by dash numbers. These are universally used abbreviations for the size of component expressed as the numerator
More informationPressure Dump Valve Service Kit for Series 3000 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationALL-PURPOSE Low and Medium Pressure TUBE FITTINGS
ALL-PURPOSE Low and Medium Pressure A Series of Specialty Tube Fittings with exceptional sealing under low and medium pressure, designed for applications sensitive to shock and vibration. Sealastic Fittings
More informationCO2 Tank Conversion Kit P.N , P.N , and P.N
Foodservice Group Multiplex Beverage Equipment Installation Instructions for CO2 Tank Conversion Kit P.N. 002247, P.N. 0022505, and P.N. 0025099 Introduction The following instructions cover the installation
More informationSeries KJ. Miniature One-touch Fittings. Applicable Tube
Guide 1 Collet Chuck ccepts nylon, soft nylon and polyurethane tubes. as large retaining force. Release button (Inch-Orange, etric-gray) ow disconnecting force. When the fitting is removed from the tubing,
More informationLP GAS PRODUCTS HIGH QUALITY GAS PRODUCTS SINCE 1957
LP GAS PRODUCTS HIGH QUALITY GAS PRODUCTS SINCE 1957 Enerco, based in Cleveland Ohio, has been at the forefront of infrared technology since 1957. This market leading technology has allowed Enerco to build
More information>B< Press Range. SALES: +44 (0) FAX: +44 (0) WEB:
>B< Press Range SALES: +44 (0)121 557 2831 FAX: +44 (0)121 520 8778 WEB: ibpconex.co.uk EMAIL: sales@ibpgroup.com 74 75 MATERIAL TUBE SPECIFICATION SIZE 6mm to 18mm 22mm 28mm to 54mm N o of turns 11 4
More informationSimple to install connection fails. The Talbot Pushfit fitting is pressure rated PN 16.
Talbot Pushfit Talbot Pushfit - Fittings for Water Pipe Talbot Grippa Universal Service Connector The Talbot Pushfit connection is a tried and tested method of connecting low, The Talbot Grippa is a universal
More informationSIMPLAIR PIPING TOOL. JXT Company
SIMPLAIR PIPING INGERSOLL-RAND SIMPLAIR PIPING With push-in fittings and lightweight anodized aluminum pipe, a SimplAir system provides ideal connection throughout your entire air distribution system.
More informationTechnifit. Union Bulkhead Flow Controller. Fractional & Metric. Push-to-Connect Fittings. March 2006
Technifit TM Push-to-Connect Fittings March 2006 Male Female Elbow Tee Union Bulkhead Flow Controller Fractional & Metric PO Box 335 12740 State Route 4 Milford Center, Ohio 43045-0335 USA Phone: 937.349.4055
More informationCONNECTION > Super-rapid fittings Series 6000 GENERAL DATA. Fitting with connecting tube. Sprint
Super-rapid fittings for plastic tubes Series 6000 Sprint Tube external diameters: 3,, 5, 6, 8, 10, 12, 1, 16 mm Fittings threads: metric (M3, M5, M6, M7), BSP (G1/8, G1/, G3/8, G1/2, G3/), BSPT (R1/8,
More informationMIDDLESEX COUNTY COLLEGE EDISON, NJ LOCAL SUPPLIER BLANKET ORDER SPECIFICATIONS
MIDDLESEX COUNTY COLLEGE EDISON, NJ 08818 LOCAL SUPPLIER BLANKET ORDER SPECIFICATIONS The College is soliciting bids to award a Local Supplier Blanket Order agreement for the purchase of supplies for the
More informationMATERIALS FOR PLUMBING SYSTEMS FITTING AND INSTALLATION GUIDE
MATERIALS FOR PLUMBING SYSTEMS FITTING AND INSTALLATION GUIDE THINK GLOBALLY, ACT LOCALLY CONTENTS Propex DZR fittings and pex 2 Why depend on Propex hot and cold piping system 3 Cross linked polyethylene
More informationHigh Pressure Equipment Medium Pressure Valves, Fittings and Tubing
igh Pressure quipment Medium Pressure Valves, ittings and Tubing service igh Pressure quipment Company has developed a line of Medium Pressure products to assure safe and easy plumbing through. These needle
More informationHigh Pressure Equipment Medium Pressure Valves, Fittings and Tubing
igh Pressure quipment Medium Pressure Valves, ittings and Tubing service igh Pressure quipment Company has developed a line of Medium Pressure products to assure safe and easy plumbing through. These needle
More informationRegO Adapters, Connector, & Fittings
RegO dapters, onnector, & Fittings Extended Type ouplings for Vapor and Liquid Service esigned especially for liquid filling and vapor equalization of LP-Gas and anhydrous ammonia. The limited travel of
More informationCryogenic Liquid Ultimate Liquid Cylinder Hose
Cryogenic Liquid Ultimate Liquid Cylinder Hose Flexible Components brand liquid cylinder hose is considered the highest quality liquid cylinder hose on the market. It effectively transfers cryogenic liquids
More information1500 Follow Spot Yoke
1500 Follow Spot Yoke Rev 1.1 2004 City Theatrical, Inc. Getting Started with the City Theatrical Follow Spot Yoke Congratulations on the purchase of your City Theatrical Follow Spot Yoke. The City Theatrical
More informationPrestolok PLS Stainless Steel Push-to-Connect Fittings
Prestolok PS Stainless Steel Push-to-Connect ittings Parker s Prestolok PS fittings are ideal for conveying corrosive fluids in aggressive environments. Prestolok PS fittings provide corrosion resistance
More informationOperating Procedures for GripTight 15.5 SDR & IPS Test Plugs
EST Group DC2518 08/01 REV 3 12/12 Page 1 of 6 Operating Procedures for GripTight SDR & IPS Test Plugs WARNING For proper operation, GripTight plugs must be assembled as shown in Figure 1. Pressure testing
More informationV48 Series 3-Way Pressure-Actuated Water-Regulating Valves With Union Fittings
Installation Instructions V48 Issue Date 08/30/01 V48 Series 3-Way Pressure-Actuated Water-Regulating Valves With Union Fittings Application IMPORTANT: The V48 Series 3-Way Pressure-Actuated Water-Regulating
More informationConnection Thread M, R(PT), Rc(PT) How to Order. Applicable tube O.D. Thread. 8 ø8. ø10. ø12. ø16. Tube (Rod)
One-touch Fittings Applicable etric Size Series K2 ow to Order Connection,, Rc(PT) Symbol 2 Body White Black Color Release button ight gray Blue Accessory Name Nipple K2N Different dia. nipple Adapter
More informationWirsbo / AquaPEX. AquaPEX Tube. White Coils. White Straight Lengths. Wirsbo AquaPEX plus Tubing. Red Coils. Blue Coils PAGE 055-1
2011 Wirsbo / AquaPEX PAGE 055-1 Code# Description Pkg Mfg# AquaPEX Tubing AquaPEX Tube Wirsbo AquaPEX tubing is used in hot and cold potable water distribution systems and Uponor residential fire safety
More informationMUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5.
Installation Instructions manual MUELLER table of contents PAGE A-20814 Wall Type General Information 2 Technical Data/ Dimensions Installation 4-5 Maintenance 6 Parts 7 Indicator Post! WARNING: 1. Read
More informationV46 Series 2-Way Pressure-Actuated Water-Regulating Valves With Union Fittings
Installation Instructions V46 Issue Date 11//1 V46 Series -Way Pressure-Actuated Water-Regulating Valves With Union Fittings Application IMPORTANT: The V46 Series -Way Pressure-Actuated Water-Regulating
More informationHow to Order. Applicable tube O.D. Thread. 8 ø8. ø10. ø12. ø16. Tube (Rod) Straight union. T Different dia. straight. F Female connector TX Male elbow
One-touch Fittings Applicable etric Size Series K2 ow to Order Connection,, Rc(PT) Symbol 2 Body White Black Color Release button ight gray Blue Accessory Name Nipple K2N Different dia. nipple Adapter
More informationALE-40. R06 Miniature Brass Body Regulator. Water and Compressed Air Service 1/8" and 1/4" PTF Port Sizes. Air line equipment.
Air line equipment R Miniature Brass Body Regulator Water and Compressed Air Service 1/" and 1/" PTF Port Sizes Compact design, corrosion resistant construction Brass body with choice of plastic or brass
More informationINSTALLATION. and INSTRUCTION MANUAL. for QUALITY AIR BREATHING SYSTEMS. Model 50 Systems Outfitted with ABM-725 Monitor C O M P A N Y
INSTALLATION and INSTRUCTION MANUAL for QUALITY AIR BREATHING SYSTEMS Model 50 Systems Outfitted with ABM-725 Monitor M A R T E C H S E R V I C E S C O M P A N Y OFFICE: (507) 843-4700 P.O. BOX 7079 Toll
More informationStromberg Fuel Tee Replacement Michael Hartman Version 1.1 February 14, 2017
Stromberg Fuel Tee Replacement Michael Hartman Version 1.1 February 14, 2017 The plastic fuel tee supplying fuel to the twin Stromberg 150CDs on my Sunbeam Alpine Series V had cracked and was spewing gas
More informationshutoff valves 900 Series psig Manual Shutoff Valves
0 6000 psig Manual Shutoff Valves Features Zero leakage Protected o-ring Full flow passages Freedom from wire drawing Panel mount standard Hand wheel or toggle handle How it Works Closed O-ring seal on
More informationCorporation Stops Technical Bulletin
Corporation Stops Technical Bulletin Available in ½", ¾", 1", 1¼", 1½", 2" Sizes The information contained in this manual was current at the time of printing. The most current versions of all Hydro Instruments
More informationService and installation must be performed by a trained/experienced service technician.
CATALOG DRAFT 09.18.2013 Service and installation must be performed by a trained/experienced service technician. All products used with combustible gas must be installed and used strictly in accordance
More informationLOKRING Stainless Steel (SS40) and Carbon Steel (CS) Pipe Fittings Table of Contents
38376 APOLLO PARKWAY WILLOUGHBY, OHIO USA 44094 www.lokring.com LOKRING Stainless Steel (40) and Carbon Steel (CS) s Table of Contents Information Page 2.. Design Page 3-4.. Pressure and Temperature Ratings
More informationACME Connectors and Fittings Extended Type Hose Couplings for Vapor and Liquid Service A7571 and A7575 Series
M onnectors and Fittings xtended Type Hose ouplings for Vapor and Liquid Service 7571 and 7575 Series esigned especially for liquid filling and vapor equalization of LP-Gas and anhydrous ammonia. The limited
More informationCatalog No. C09118A. Nitrogen Gas Spring Linked System Components
Catalog No. C09118A Nitrogen Gas Spring Linked System Components Everything You Need to Construct a Linked System Linked Systems Introduction Numerous Piping Options Many customers recognize the benefits
More informationVisual Index K4 BSP Adapters
K4 BP Adapters I 4300 atalog K4 BP Adapters 60 one BP Adapters traights HMK4 Union WMK4W4NM Bulkhead Union F6MK4 60 wivel / 60 one H6MK4 wivel Union FMK4 NPTF / 60 one F3MK4 BPT / 60 one G4MK4 / 60 one
More informationStirred Reactors and Pressure Vessels
P a r r I n s t r u m e n t C o m p a n y Stirred Reactors and Pressure Vessels Designing and Building Quality Pressure Apparatus for Over 100 Years Bulletin 4500 Volume 12 Start Chapter Six This pdf is
More informationHalsey Taylor Owners Manual
Halsey Taylor Owners Manual Refrigerated Marblyte Fountains with Back Panel HRFG - ER HRFG - SR HRFG - SER Installer To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS
More informationTools & Installation. Tools & Installation Index
L Radius +0 59-2 32 60 +2 A B -0 32 C E F.09" ia. Weep Hole Tools & Installation MAXIMATOR offers manual Coning and Threading tools that are designed to prepare accurate tubing ends to accept the medium,
More informationAdapters and Tube Fittings Index
dapters and Tube Fittings Index lphabetical Index PRESSURE HOSE HIGH PRESSURE HOSE HOSE FITTINGS TUBE FITTINGS DESCRIPTION PGES DESCRIPTION PGES DESCRIPTION PGES DESCRIPTION PGES dapters 196 Braze and
More information1 Exam Prep NFPA 99 Health Care Facilities Questions and Answers (Plumbing Contractor)
1 Exam Prep NFPA 99 Health Care Facilities Questions and Answers (Plumbing Contractor) 1. According to NFPA 99, SCFM is an acronym for. a) Surface Conditions at Fahrenheit Mercury b) Standard Conditions
More informationINDEX SHPE SMPSC SMPG SHPT SMPBC SMPCR SHPCR SMPCP SMPP SHPSC SMPN SMPE SHPUC SHPBC SHPP SHPN. High Pressure Fittings. Pg. 9. Pg. 5. Pg. 3. Pg.
High Fittings Micro Weld Fittings INDEX SMPG Pg. 3 SMPUC Union Coupling (Slip Type) Pg. 5 SHPE Elbow Pg. 9 Gland SMPCR Pg. 4 SMPBC Bulkhead coupling Pg. 5 SHPT Tee Pg. 10 Collar SHPC Pg. 10 SMPP Pg. 4
More informationSchroeder Check Test Point System
Perforated polyamide / kevlar hose, 2 mm ID, 5 mm OD, plastic dust cap. L in (mm) P (max) psi (bar) 6 (150) 10,000 (680) 12 (300) 10,000 (680) 24 (610) 10,000 (680) 36 (915) 10,000 (680) 48 (1220) 10,000
More informationPush-in fittings NPQH
Key features Application Effortless selection of the right fitting. Festo offers a secure solution for every connection. The convenient push-in fitting system includes well over 1000 types of standard
More informationSUMMITTM 400 & 600. Natural Gas Barbecues. Step-By-Step Guide
SUMMITTM 400 & 600 Natural Gas Barbecues Step-By-Step Guide W E B E R W E B E R W E B E R W E B E R Summit 400 NG Summit 600 NG CANADIAN GAS ASSOCIATION R A P P R O V E D WARNING: Follow all leak check
More informationNickel-Plated Brass Right Angle Flow Control Valves NPTF/Inch Series GSCU, GMCU, GSVU, GMVU, GSCO, GMCO
Nickel-Plated Brass Right Angle Flow Control Valves NPTF/Inch Series GSCU, GMCU, GSVU, GMVU, GSCO, GMCO Swivel Design : Meter-Out, Meter-In and Needle Orifice Tube Diameter OD: 1/8, 5/2, 1/4, 5/16, /8
More informationAquor House Hydrant V2
Aquor House Hydrant V2 IN-WALL OUTDOOR FAUCET SYSTEM FLUSH-MOUNT QUICK-CONNECT SELF-DRAINING ANTI-SIPHON NON-FREEZE VBH-SERIES AQUOR HOUSE HYDRANT V2: WALL HYDRANT / FREEZELESS SILLCOCK Freezeless sillcock
More informationFlexible Metal Hose Products
Flexible Metal Hose Products Specialty Flexible Hose Solutions of Stainless Steel The AEROCOM Advantage Aerocom offers engineered solutions that address specific flexible piping challenges such as vibration,
More informationINDUSTRIAL PRODUCTS. Industrial Products Catalog. Innovative Solutions for Gas Management Systems ENTERPRISES
INDUSTRIAL PRODUCTS ENTERPRISES Industrial Products Catalog Innovative Solutions for Gas Management Systems This catalog provides a comprehensive source of information on Western s line of products used
More informationStorage Systems and Accessories
Storage Systems and Accessories High Pressure Air and Inert Gases 4500-6000 PSIG DOT and ASME Cylinders High Pressure Storage Systems If an application requires storage, either in the form of a single
More informationQuality Plastic Pipe Fittings. Technical Data. Fabricated PVC Fittings IPS Class 100, 125, 160, 200 SCH 40 & SCH 80 Solvent Weld & Gasketed
Quality Plastic Pipe Fittings Technical Data Fabricated PVC Fittings IPS Class 100, 125, 160, 200 SCH 40 & SCH 80 Solvent Weld & Gasketed Effective April 1, 2002 PIPE DIMENSIONS IPS-IRON PIPE SIZE Minimum
More informationTRADITIONAL HIGH VIBRATION HOSE SYSTEM THE STANDARD FOR MANY AUTOMOTIVE APPLICATIONS
O-Ring Face Seal Hose TRADITIONAL HIGH VIBRATION HOSE SYSTEM THE STANDARD FOR MANY AUTOMOTIVE APPLICATIONS O-Ring Face Seal METAL FORMING SOLUTIONS THE STANDARD FOR MANY AUTOMOTIVE APPLICATIONS Table of
More informationHoses and Lances 20,000 PSI
Jetstream provides a full arrangement of hoses and flex lances for ultra high pressure waterblasting. The hoses and lances are designed to be durable and reliable for any 20,000 psi application. A large
More informationINSTRUCTION MANUAL & PARTS
AIR LINE PURIFIERS FOR BREATHING EQUIPMENT AP-C RADEX INSTRUCTION MANUAL & PARTS 01-0-11 introduction CANABLAST BREATHING EQUIPMENT PURIFIER CAN BE USED IN CONBINATION WITH WITH OTHER SAFEGUARDS TO SUPPLY
More informationASYBCO 90 O ELBOW LONG RADIUS O.D. I.D.
90 O ELBOW LONG RADIUS Standard weight Extra strong Schedule 160 Double extra strong ASTM A-234 ASME / ANSI B16.9 Carbon and ferritic alloy steel Produced from X-rayed, stress-relieve welded pipe. Welds
More informationInstruments AQDC. Aluminium Quick Disconnects. Light-weight, quick and reliable method a making a number of pneumatic connections.
AQDC Aluminium Quick Disconnects Instruments Light-weight, quick and reliable method a making a number of pneumatic connections. 8, 16, 24 and 32 port stainless steel quick disconnects. Available with
More informationPlok. Rapid Mating Multi-Pin Industrial Connector. Amphenol Industrial Sine Systems * Pyle Connectors Corporation
- Plok Rapid Mating Multi-Pin Industrial onnector mphenol Industrial Sine Systems * Pyle onnectors orporation eatures and enefits Rapid mate spring loaded, push to mate, pull to unmate coupling system
More informationOperation Manual. Diaphragm Sensed Gas Pressure Regulators
687 Technology Way Napa, CA 94558 Phone: (707) 259-0102 FAX: (707) 259-0117 www.aptech-online.com Diaphragm Sensed Gas (AP/AZ/AK Models: 20, 100, 500, 1000, 1000T 10PA, 1100, 1200, 12PA, 1300, 1400T, 14PA,
More informationMUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.
Installation Instructions manual MUELLER table of contents PAGE A-20808 General Information 2 Technical Data 3 Dimensions 4 A-20809 Non-Adjustable Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator
More informationSee Plastic Pipe Engineering Guide for additional information
Schedule 40 PVC Pipe Dimensions & Pressure Ratings Schedule 40 Pipe om. Pipe Size (in) O.D. Average I.D. in. Wall ominal Wt./Ft. aximum W.P. PSI* 1/8 0.405 0.249 0.068 0.051 810 1/4 0.540 0.344 0.088 0.086
More informationPreparation and Installation of the Sanitary BDI-FLX Sensor and Connection to the BDI-FLX Interface Cable
GEP-6075 Rev. B 101574 Ref. I.D.: 16973 Preparation and Installation of the Sanitary BDI-FLX Sensor and Connection to the BDI-FLX Interface Cable WARNING USER SHOULD READ AND THOROUGHLY UNDERSTAND THESE
More informationSeries V47 Temperature Actuated Modulating Valves
PSC0302 European Refrigeration Controls Catalogue Catalog Section 7 Product Bulletin V47 Series V47 Temperature Actuated Modulating Valves Introduction The V47 modulating water valves regulate the flow
More informationTechnical Bulletin. Parts and Service News. LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6
Equipment Affected Technical Bulletin LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6 Ford 4.2L V-6 powered tractors with LPG fuel systems. Part Description Discrepancy Fuel Pressure Lock-off
More informationSpeed control assembly model A-1
Pressure Regulation 533a 1. DESCRIPTION The Viking Speed Control Assembly provides adjustment of the opening speed of Viking Deluge Valves, and adjustment of both the opening and closing speed of Viking
More informationInstallation Procedure for your Disco Double Kit, by Airgun Lab, LLC.
Disco Double Installation Instructions Copyright Airgun Lab LLC Rev D January 2016 page 1 of 6 Installation Procedure for your Disco Double Kit, by Airgun Lab, LLC. Step 1, gather tools. Tools required
More informationPROCEDURE TWO-PLY TESTABLE BELLOWS D 1 OF 5 TWO PLY BELLOWS TEST PROCEDURE
PROCEDURE TWO-PLY TESTABLE BELLOWS D 1 OF 5 TWO PLY BELLOWS TEST PROCEDURE Prepared by: Pathway Piping Solutions Daniel L. Edgar, PE Pine Valley, Ca 91962 Phone: (619) 473-8248 FAX: (619) 473-8148 Pathway
More informationJARVIS. Model CPE Hock and Neck Cutter EQUIPMENT... TABLE OF
74 Hock and Neck Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page with Control Circuit. 4304003 only... 4304004 Balancer... 1350084 Control Circuit... 3350010 Air Hose (Yellow)... 3323003
More information