Liquid Tight Strain Relief Fittings, Accessories & Conduit System

Transcription

1 Liquid Tight Strain Relief Fittings, ccessories & Our Service makes the difference! 20 years of excellence!

2 Table of Contents Nylon Strain Relief Fittings Page escription 3 Nylon Fittings - Introduction 4 Straight omelex - PG/NPT s 5 Straight omelex - Metric s 6 Straight omelex - Elongated PG/Metric s 7 Straight omelex - Reduced/Enlarged ody - PG 8 Elbow omelex - PG/NPT & Metric s 9 igh Performance w/ Clamp - PG & Metric s 9 Romex Fittings for Cable 10 Multi-ole Fittings - PG s 11 Multi-ole Fittings - NPT s 12 Multi-ole Fittings - Metric s ROMEX is a federally registered trademark of Southwire Company. Nickel Plated rass Fittings Page escription 13 Nickel Plated rass Fittings - Introduction 14 Straight omelex - PG/NPT & Metric s 15 Mini WI - Smallest Cable O.. - PG & Metric 15 WI XL - Largest Cable O.. - Metric & SPP 16 Straight omelex - Elongated PG/Metric s 17 Elbow ome - PG/Metric s & Flange 17 Clamp igh Performance - PG/NPT/Metric 17 Clamp igh Performance - Elongated PG/Metric 18 EMI/RFI Fittings: Product Features 19 EMI/RFI Fittings: pplications & ssembly 20 EMI/RFI: Standard - PG/NPT/Metric s 20 EMI/RFI: Standard - Elongated PG/Metric 21 EMI/RFI: Feed-Through - PG/NPT/Metric s 21 EMI/RFI: Feed-Through - Elongated PG/Metric 22 Multi-ole Fittings - PG s 23 Multi-ole Fittings - NPT s 24 Multi-ole Fittings - Metric s PVF & Stainless Steel Fittings Strain Relief ccessories Page escription 28 ccessories - Overview 29 Locking Nuts: lack & Gray Nylon, Nickel Plated rass, EMI/RFI, Zinc Plated Steel 30 O-Rings & Seal Rings 30 lind Plugs - Nylon 31 ome Plugs - Nylon & Nickel Plated rass 31 ex Plugs - lack Nylon & Nickel Plated rass 32 ex Plugs - Stainless Steel 32 Cable Clamp - Nickel Plated rass 33 Socket & Ratchet es dapters, Reducers, Enlargers Page Page escription 34 dapters - Nickel Plated rass & luminum 35 dapters - lack Nylon 36 Reducers - Nickel Plated rass (ex & Round) 37 Reducers - lack & Gray Nylon 38 Reducers - Stainless Steel 39 Enlargers - lack Nylon & Nickel Plated rass escription 40 - Introduction 40 Corrugated Conduit: Standard/Super Flex 40 Mounting rackets 41 Push-In Fittings 42 Turn-to-Seal Fittings 43 Snapclic-UO Fittings - lack Nylon 43 Snapclic-UO Fittings - Nickel Plated rass 44 ouble-seal Fittings 44 Flange/ulkhead Fittings Page escription 25 PVF (Teflon ) - PG/NPT & Metric s 26 PVF (Nickel Plated rass) - PG/NPT & Metric 26 PVF (Nickel Plated rass) - Elongated PG/Metric 27 Stainless Steel Fittings - PG/NPT & Metric s Teflon is a federally registered trademark of upont ow Elastomer. Why choose Sealcon as your cable management partner? Sealcon was founded in the fall of 1989 in Centennial, Colorado. Our goal is to provide customers with the best possible cable management solution, including Liquid Tight Strain Relief Fittings, Flexible Conduit, Circular Connectors, Industrial Enclosures and related products. We are proud to represent ummel, the leading German manufacturer of Liquid Tight Strain Relief Fittings and ccessories. These products meet UL, CS, RoS, eca E, European VE and CE standards. ummel is ISO 9001 quality certified and has continuously developed leading edge technology solutions. Sealcon can ship your order usually within 24 hours from our central warehouse in Colorado. We replenish our inventory weekly and can respond to changing demands quickly. Technical Information Page escription 45 Material Specifications & Temperature Ranges 46 NEM Ratings 47 IP Ratings 48 Sizes & imensions for Sealcon Fittings 48 Torque Specifications & Pull-Test Rating 49 Specifications (NPT, Metric, PG, SPP) Other Products / Index Page escription 50 Circular Connectors 51 Industrial Enclosures 52 Strain Relief Fittings for azardous Locations 53 Faxback Form 54 P/N Index / Cross Reference This catalog is a condensed version of the ummel master catalog, which is available to our customers upon request. Our experienced staff will help to answer technical questions and recommend the correct samples for evaluation. Purchase orders, received before noon MST are often shipped the same day. Please give us a call so we can help you with your requirements. anspeter Spühler, President 2

3 Features & enefits: Nylon Liquid Tight Strain Relief Fittings Features & enefits Liquid Tight - submersible to 300 ft. - NEM 4x & 6 (IP 68 / IP 69K) ighest pressure rating - Patented form seal meets 150 PSIG (10 bar) Flame protected - V0 rated according to UL 94 alogen- and Phosphorous free materials Safety - Ratchet to prevent ome from coming loose under vibration Large selection - Cable Range from.08 (2 mm) to 1.38 (35 mm) Non-Corrosive - Resistant to salt water, weak acids, weak alkalis, alcohol, esters, ketones, ether, gasoline, mineral, animal & vegetable oil. urable - Rugged Construction Environmentally compliant - RoS & eca E UL/UR E CS VE CGE ZERO UE114 PTENT Nickel Plated rass Nylon Strain Relief Your One Stop Solution For ll Cable & Wire ccessories! Unique Product Pull-out Resistance & Cable Protection Overlapping clamping splines apply a concentric force, thereby preventing the form seal from being pulled out of the fitting. This ensures pull-out protection without damage to the cable. Submersible The patented recess and high performance seal guarantees NEM 4x & 6 (IP 68 / IP 69K) at 150 PSIG (10 bar). ccessories Time Saving Installation Simply push the cable through Strain Relief Fitting - Tighten ome or Flex Nut - one! No disassembly of the Fitting required: Insert Cable - Tighten Nut - Finished! Standard, Reduced and Multi-ole Inserts Modularity: increase and decrease cable opening by swapping out inserts to accommodate various cable sizes & configurations. Rugged Construction The self locking CME thread prevents the dome nut from being pulled out under extreme lateral force. Liquid Tight Molded groove for an optional O-Ring. The use of an O-Ring results in a liquid tight seal between fitting and housing. Elbow Fittings For Space and time saving installations: Open Elbow - Insert cable - Snap close - Tighten Nut - Finished! vailable with ome or Flex Nut. Flex Nut Kinking and chafing of the cable is eliminated. 3 dapter,reducer,enlarger

4 Nickel Plated rass Nylon Strain Relief ccessories Nylon Liquid Tight Strain Relief Fittings Standard - PG & NPT s Part Numbers Cable Range imensions in Inches (mm) (See Page 5) ome Fittings Flex Fittings C F 1 lack Gray lack Gray Clearance ole ody ody s (ome) (Flex) Inches (mm) +.01 (+.25 mm) C07-K C07-GY CF07-K CF07-GY (3-6.5) PG 7 / C07R-K C07R-GY CF07R-K CF07R-GY (2-5) 1/4 NPT.49 (12.5).83 (21) 2.13 (54).31 (8).59 (15) C09-K C09-GY CF09-K CF09-GY (4-8) C09R-K C09R-GY CF09R-K CF09R-GY (2-6) PG 9.60 (15.2).87 (22) 2.48 (63).31 (8).75 (19) C11-K C11-GY CF11-K CF11-GY (5-10) C11R-K C11R-GY CF11R-K CF11R-GY (3-7) PG (18.5).98 (25) 3.07 (78).31 (8).87 (22) /.75 (19) C13-K C13-GY CF13-K CF13-GY (6-12) C13R-K C13R-GY CF13R-K CF13R-GY (5-9) PG (20.3) 1.06 (27) 3.54 (90).35 (9).94 (24) C16-K C16-GY CF16-K CF16-GY (10-14) C16R-K C16R-GY CF16R-K CF16R-GY (7-12) PG (22.3) 1.10 (28) 3.94 (100).39 (10) 1.06 (27) C21-K C21-GY CF21-K CF21-GY (13-18) C21R-K C21R-GY CF21R-K CF21R-GY (9-16) PG (28.4) 1.22 (31) 4.49 (114).43 (11) 1.30 (33) C29-K C29-GY (18-25) C29R-K C29R-GY (13-20) PG (37.3) 1.54 (39) -.43 (11) 1.65 (42) C36-K C36-GY (22-32) C36R-K C36R-GY (20-26) PG (47) 1.89 (48) -.51 (13) 2.09 (53) C42-K C42-GY (32-38) C42R-K C42R-GY (25-31) PG (54.1) 1.93 (49) -.51 (13) 2.36 (60) C48-K C48-GY (37-44) C48R-K C48R-GY (29-35) PG (59.4) 1.93 (49) -.55 (14) 2.56 (65) dapter,reducer,enlarger 4 C09N-K C09N-GY CF09N-K CF09N-GY (4-8) C09NR-K C09NR-GY CF09NR-K CF09NR-GY (2-6) C13N-K C13N-GY CF13N-K CF13N-GY (6-12) C13NR-K C13NR-GY CF13NR-K CF13NR-GY (5-9) C16N-K C16N-GY CF16N-K CF16N-GY (10-14) C16NR-K C16NR-GY CF16NR-K CF16NR-GY (7-12) C21N-K C21N-GY CF21N-K CF21N-GY (13-18) C21NR-K C21NR-GY CF21NR-K CF21NR-GY (9-16) C29N-K C29N-GY (18-25) C29NR-K C29NR-GY (13-20) C29L-K C29L-GY (18-25) C29LR-K C29LR-GY (13-20) C36N-K C36N-GY (22-32) C36NR-K C36NR-GY (20-26) The straight PG 7 thread fits a 1/4 NPT female or 1/2-20 UNF thread. imensions and specifications may be changed without prior notice. 3/8 NPT.68 (17.2).87 (22) 2.48 (63).59 (15).87 (22) /.75 (19) 1/2 NPT.83 (21.1) 1.06 (27) 3.54 (90).51 (13).94 (24) 1/2 NPT.83 (21.1) 1.10 (28) 3.94 (100).51 (13) 1.06 (27) 3/4 NPT 1.05 (26.7) 1.22 (31) 4.49 (114).55 (14) 1.30 (33) 1 NPT 1.35 (34.3) 1.54 (39) -.75 (19) 1.65 (42) 1-1/4 NPT 1.65 (41.9) 1.54 (39) -.63 (16) 1.81 (46) / 1.65 (42) 1-1/2 NPT 1.92 (48.7) 1.89 (48) -.79 (20) 2.09 (53) Optional Locking Nuts, O-Rings & other ccessories starting at page 28. ome Fittings also available with the following approvals:

5 Nylon Liquid Tight Strain Relief Fittings Standard - Metric s Part Numbers Cable Range imensions in Inches (mm) ome Fittings Flex Fittings C F 1 lack Gray lack Gray Clearance ody ody ole s (ome) (Flex) Inches (mm) C12M-K C12M-GY CF12M-K CF12M-GY (3-6.5) C12MR-K C12MR-GY CF12MR-K CF12MR-GY (2-5) C16M-K C16M-GY CF16M-K CF16M-GY (4-8) C16MR-K C16MR-GY CF16MR-K CF16MR-GY (2-6) C17M-K C17M-GY CF17M-K CF17M-GY (5-10) C17MR-K C17MR-GY CF17MR-K CF17MR-GY (3-7) C20M-K C20M-GY CF20M-K CF20M-GY (6-12) C20MR-K C20MR-GY CF20MR-K CF20MR-GY (5-9) C22M-K C22M-GY CF22M-K CF22M-GY (10-14) C22MR-K C22MR-GY CF22MR-K CF22MR-GY (7-12) C25M-K C25M-GY CF25M-K CF25M-GY (13-18) C25MR-K C25MR-GY CF25MR-K CF25MR-GY (9-16) C32M-K C32M-GY (18-25) C32MR-K C32MR-GY (13-20) C40M-K C40M-GY (22-32) C40MR-K C40MR-GY (20-26) C50M-K C50M-GY (32-38) C50MR-K C50MR-GY (25-31) C63M-K C63M-GY (37-44) C63MR-K C63MR-GY (29-35) +.01 (+.25 mm) M12 x (12).83 (21) 2.13 (54).31 (8).59 (15) M16 x (16).87 (22) 2.48 (63).31 (8).75 (19) M16 x (16).98 (25) 3.07 (78).31 (8).87 (22) M20 x (20) 1.06 (27) 3.54 (90).35 (9).94 (24) M20 x (20) 1.10 (28) 3.94 (100).35 (9) 1.06 (27) M25 x (25) 1.22 (31) 4.49 (114).43 (11) 1.30 (33) M32 x (32) 1.54 (39) -.43 (11) 1.65 (42) M40 x (40) 1.89 (48) -.51 (13) 2.09 (53) M50 x (50) 1.93 (49) -.51 (13) 2.36 (60) M63 x (63) 1.93 (49) -.55 (14) 2.56 (65) / 2.68 (68) Nickel Plated rass Nylon Strain Relief ccessories F 1 Optional Locking Nuts, O-Rings & other ccessories starting at page 28. Installs in either clearance or threaded holes. C F 1 imensions and specifications may be changed without prior notice. Suggested Clearance ole for Non-ed Mounting lso available with the following approvals: 5 dapter,reducer,enlarger

6 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 6 Nylon Liquid Tight Strain Relief Fittings Elongated - PG & Metric s Part Numbers Cable Range imensions in Inches (mm) ome Fittings Flex Fittings C F 1 lack Gray lack Gray Clearance ody ody ole s (ome) (Flex) Inches (mm) C07C-K C07C-GY CF07C-K CF07C-GY (3-6.5) C07CR-K C07CR-GY CF07CR-K CF07CR-GY (2-5) C09C-K C09C-GY CF09C-K CF09C-GY (4-8) C09CR-K C09CR-GY CF09CR-K CF09CR-GY (2-6) C11C-K C11C-GY CF11C-K CF11C-GY (5-10) C11CR-K C11CR-GY CF11CR-K CF11CR-GY (3-7) C13C-K C13C-GY CF13C-K CF13C-GY (6-12) C13CR-K C13CR-GY CF13CR-K CF13CR-GY (5-9) C16C-K C16C-GY CF16C-K CF16C-GY (10-14) C16CR-K C16CR-GY CF16CR-K CF16CR-GY (7-12) C21C-K C21C-GY CF21C-K CF21C-GY (13-18) C21CR-K C21CR-GY CF21CR-K CF21CR-GY (9-16) C29C-K C29C-GY (18-25) C29CR-K C29CR-GY (13-20) C36C-K C36C-GY (22-32) C36CR-K C36CR-GY (20-26) C42C-K C42C-GY (32-38) C42CR-K C42CR-GY (25-31) C48C-K C48C-GY (37-44) C48CR-K C48CR-GY (29-35) F 1 Optional Locking Nuts, O-Rings & other ccessories starting at page 28. Wall C12-K C12-GY CF12-K CF12-GY (3-6.5) C12R-K C12R-GY CF12R-K CF12R-GY (2-5) C16-K C16-GY CF16-K CF16-GY (4-8) C16R-K C16R-GY CF16R-K CF16R-GY (2-6) C17-K C17-GY CF17-K CF17-GY (5-10) C17R-K C17R-GY CF17R-K CF17R-GY (3-7) C20-K C20-GY CF20-K CF20-GY (6-12) C20R-K C20R-GY CF20R-K CF20R-GY (5-9) C22-K C22-GY CF22-K CF22-GY (10-14) C22R-K C22R-GY CF22R-K CF22R-GY (7-12) C25-K C25-GY CF25-K CF25-GY (13-18) C25R-K C25R-GY CF25R-K CF25R-GY (9-16) C32-K C32-GY (18-25) C32R-K C32R-GY (13-20) C40-K C40-GY (22-32) C40R-K C40R-GY (20-26) C50-K C50-GY (32-38) C50R-K C50R-GY (25-31) C63-K C63-GY (37-44) C63R-K C63R-GY (29-35) C +.01 (+.25 mm) imensions and specifications may be changed without prior notice. PG 7.49 (12.5).83 (21) 2.13 (54).59 (15).59 (15) PG 9.60 (15.2).87 (22) 2.48 (63).59 (15).75 (19) PG (18.5).98 (25) 3.07 (78).59 (15).87 (22) PG (20.3) 1.06 (27) 3.54 (90).59 (15).94 (24) PG (22.3) 1.10 (28) 3.94 (100).59 (15) 1.06 (27) PG (28.4) 1.22 (31) 4.49 (114).59 (15) 1.30 (33) PG (37.3) 1.54 (39) -.59 (15) 1.65 (42) PG (47) 1.89 (48) -.71 (18) 2.09 (53) PG (54.1) 1.93 (49) -.71 (18) 2.36 (60) PG (59.4) 1.93 (49) -.71 (18) 2.56 (65) Elongated is recommend where the Strain Relief has to pass through a thick wall or the application just needs the extra thread length. F 1 Wall Suggested Clearance ole for Non-ed Mounting ome Fittings also available with the following approvals: M12 x (12).83 (21) 2.13 (54).59 (15).59 (15) M16 x (16).87 (22) 2.48 (63).59 (15).75 (19) M16 x (16).98 (25) 3.07 (78).59 (15).87 (22) M20 x (20) 1.06 (27) 3.54 (90).59 (15).94 (24) M20 x (20) 1.10 (28) 3.94 (100).59 (15) 1.06 (27) M25 x (25) 1.22 (31) 4.49 (114).59 (15) 1.30 (33) M32 x (32) 1.54 (39) -.59 (15) 1.65 (42) M40 x (40) 1.89 (48) -.71 (18) 2.09 (53) M50 x (50) 1.93 (49) -.71 (18) 2.36 (60) M63 x (63) 1.93 (49) -.71 (18) 2.56 (65) / 2.68 (68)

7 Nylon Liquid Tight Strain Relief Fittings Reduced ody - PG s Strain Relief with Reduced ody Part Numbers Cable Range imensions in Inches (mm) ome Fittings Flex Fittings C F 1 lack Gray lack Gray Clearance ody ody ole s (ome) (Flex) Inches (mm) C09-K C09-GY CF09-K CF09-GY (3-6.5) C09R-K C09R-GY CF09R-K CF09R-GY (2-5) C11-K C11-GY CF11-K CF11-GY (4-8) C11R-K C11R-GY CF11R-K CF11R-GY (2-6) C13-K C13-GY CF13-K CF13-GY (5-10) C13R-K C13R-GY CF13R-K CF13R-GY (3-7) C16-K C16-GY CF16-K CF16-GY (6-12) C16R-K C16R-GY CF16R-K CF16R-GY (5-9) C21-K C21-GY CF21-K CF21-GY (10-14) C21R-K C21R-GY CF21R-K CF21R-GY (7-12) F 1 F (+.25 mm) PG 9.60 (15.2).83 (21) 2.13 (54).31 (8) PG (18.5).87 (22) 2.48 (63).31 (8) PG (20.3).98 (25) 3.07 (78).35 (9) PG (22.3) 1.06 (27) 3.54 (90).39 (10) PG (28.4) 1.10 (28) 3.94 (100).43 (11) If your cable diameter decreases, but your thread remains the same..59 (15) /.75 (19).75 (19) /.87 (22).87 (22) /.94 (24).94 (24) / 1.06 (27) 1.06 (27) / 1.30 (33) Nickel Plated rass Nylon Strain Relief C Suggested Clearance ole for Non-ed Mounting Strain Relief with Enlarged ody Part Numbers Cable Range imensions in Inches (mm) ome Fittings Flex Fittings C F 1 lack Gray lack Gray Clearance ole ody ody s (ome) (Flex) Inches (mm) +.01 (+.25 mm) C07G-K C07G-GY CF07G-K CF07G-GY (4-8) PG 7 / C07GR-K C07GR-GY CF07GR-K CF07GR-GY (2-6) 1/4 NPT.49 (12.5).87 (22) 2.48 (63).31 (8).75 (19) C09G-K C09G-GY CF09G-K CF09G-GY (5-10) C09GR-K C09GR-GY CF09GR-K CF09GR-GY (3-7) PG 9.60 (15.2).98 (25) 3.07 (78).31 (8).87 (22) C11G-K C11G-GY CF11G-K CF11G-GY (6-12) C11GR-K C11GR-GY CF11GR-K CF11GR-GY (5-9) PG (18.5) 1.06 (27) 3.54 (90).31 (8).94 (24) C13G-K C13G-GY CF13G-K CF13G-GY (10-14) C13GR-K C13GR-GY CF13GR-K CF13GR-GY (7-12) PG (20.3) 1.10 (28) 3.94 (100).35 (9) 1.06 (27) C16G-K C16G-GY CF16G-K CF16G-GY (13-18) C16GR-K C16GR-GY CF16GR-K CF16GR-GY (9-16) PG (22.3) 1.22 (31) 4.49 (114).39 (10) 1.30 (33) ome Fittings also available with the following approvals: F 1 Nylon Liquid Tight Strain Relief Fittings Enlarged ody - PG s C If your cable diameter increases, but your thread remains the same. F 1 Optional Locking Nuts, O-Rings & other ccessories starting at page 28. Suggested Clearance ole for Non-ed Mounting imensions and specifications may be changed without prior notice. 7 ccessories dapter,reducer,enlarger

8 Nickel Plated rass Nylon Strain Relief Inches (mm) E09-K E09-GY EF09-K EF09-GY (4-8) E09R-K E09R-GY EF09R-K EF09R-GY (2-6) E11-K E11-GY EF11-K EF11-GY (5-10) E11R-K E11R-GY EF11R-K EF11R-GY (3-7) E13-K E13-GY EF13-K EF13-GY (6-12) E13R-K E13R-GY EF13R-K EF13R-GY (5-9) E16-K E16-GY EF16-K EF16-GY (10-14) E16R-K E16R-GY EF16R-K EF16R-GY (7-12) E21-K E21-GY EF21-K EF21-GY (13-18) E21R-K E21R-GY EF21R-K EF21R-GY (9-16) E29-K E29-GY (18-25) E29R-K E29R-GY (13-20) Nylon Liquid Tight Strain Relief Fittings 90º Snap Elbow - PG/NPT/Metric s Part Numbers Cable Range imensions in Inches (mm) ome Fittings Flex Fittings C E F lack Gray lack Gray Clearance ody ody ole s (ome) (Flex) +.01 (+.25 mm) PG 9.60 (15.2) 1.77 (45) 3.35 (85).91 (23).31 (8).75 (19) PG (18.5) 1.97 (50) 4.05 (103) 1.06 (27).31 (8).87 (22) PG (20.3) 2.24 (57) 4.69 (119) 1.20 (30.5).35 (9).94 (24) PG (22.3) 2.32 (59) 5.12 (130) 1.28 (32).39 (10) 1.06 (27) PG (28.4) 2.87 (73) 6.14 (156) 1.57 (40).43 (11) 1.30 (33) PG (37.3) 3.58 (91) (51.5).43 (11) 1.65 (42) ccessories dapter,reducer,enlarger 8 E09N-K E09N-GY EF09N-K EF09N-GY (4-8) E09NR-K E09NR-GY EF09NR-K EF09NR-GY (2-6) E13N-K E13N-GY EF13N-K EF13N-GY (6-12) E13NR-K E13NR-GY EF13NR-K EF13NR-GY (5-9) E16N-K E16N-GY EF16N-K EF16N-GY (10-14) E16NR-K E16NR-GY EF16NR-K EF16NR-GY (7-12) E21N-K E21N-GY EF21N-K EF21N-GY (13-18) E21NR-K E21NR-GY EF21NR-K EF21NR-GY (9-16) E29N-K E29N-GY (18-25) E29NR-K E29NR-GY (13-20) E16M-K E16M-GY EF16M-K EF16M-GY (4-8) E16MR-K E16MR-GY EF16MR-K EF16MR-GY (2-6) E20M-K E20M-GY EF20M-K EF20M-GY (6-12) E20MR-K E20MR-GY EF20MR-K EF20MR-GY (5-9) E25M-K E25M-GY EF25M-K EF25M-GY (13-18) E25MR-K E25MR-GY EF25MR-K EF25MR-GY (9-16) E32M-K E32M-GY (18-25) E32MR-K E32MR-GY (13-20) Liquid Tight Elbow Strain Relief Fitting for space and time saving applications. Suggested Clearance ole for Non-ed Mounting E (F) imensions and specifications may be changed without prior notice. 3/8 NPT.68 (17.2) 1.77 (45) 3.35 (85).91 (23).59 (15).75 (19) 1/2 NPT.83 (21.1) 2.24 (57) 4.69 (119) 1.20 (30.5).51 (13).94 (24) 1/2 NPT.83 (21.1) 2.32 (59) 5.12 (130) 1.24 (31.5).51 (13) 1.06 (27) 3/4 NPT 1.05 (26.7) 2.87 (73) 6.14 (156) 1.57 (40).51 (13) 1.30 (33) 1 NPT 1.35 (34.3) 3.58 (91) (50).75 (19) 1.65 (42) M16 x (16) 1.77 (45) 3.35 (85).91 (23).31 (8).75 (19) M20 x (20) 2.24 (57) 4.68 (119) 1.20 (30.5).35 (9).94 (24) M25 x (25) 2.87 (73) 6.14 (156) 1.57 (40).43 (11) 1.30 (33) M32 x (32) 3.58 (91) (51.5).43 (11) 1.65 (42) E Optional Locking Nuts, O-Rings & Other ccessories starting at page 28. C (F)

9 Nylon Liquid Tight Strain Relief Fittings Clamp igh Performance - PG & Metric s igh Performance Fittings with Clamp Part Numbers Cable Range Clamp Fittings Inches (mm) imensions in Inches (mm) F 1 Clearance ole +.01 (+.25 mm) ody s C09-CP (4-8) PG 9.60 (15.2) 1.14 (29).59 (15).75 (19) C11-CP (6-10) PG (18.5) 1.28 (32.5).59 (15).87 (22) C13-CP (6-12) PG (20.3) 1.40 (35.5).59 (15).94 (24) C16-CP (10-14) PG (22.3) 1.48 (37.5).39 (10) 1.06 (27) C21-CP (13-18) PG (28.4) 1.61 (41).43 (11) 1.30 (33) C29-CP (18-25) PG (37.3) 1.93 (49).43 (11) 1.65 (42) C36-CP (22-32) PG (47) 2.28 (58).51 (13) 2.09 (53) C42-CP (32-38) PG (54.1) 2.42 (61.5).51 (13) 2.36 (60) C48-CP (37-44) PG (59.4) 2.44 (62).55 (14) 2.56 (65) C16M-CP (4-8) M16 x (16) 1.14 (29).59 (15).75 (19) C20M-CP (6-12) M20 x (20) 1.40 (35.5).59 (15).94 (24) C25M-CP (13-18) M25 x (25) 1.61 (41).43 (11) 1.30 (33) C32M-CP (18-25) M32 x (32) 1.93 (49).43 (11) 1.65 (42) C40M-CP (22-32) M40 x (40) 2.28 (58).51 (13) 2.09 (53) C50M-CP (32-38) M50 x (50) 2.42 (61.5).51 (13) 2.36 (60) C63M-CP (37-44) M63 x (63) 2.44 (62).55 (14) 2.56 (65) / 2.68 (68) Strain Relief Fittings with Inserts for Cables. They are made of Nylon with una-n form seal and are resistant to salt water, weak acids, weak alkalis, alcohol, ether, esters, ketones, mineral, animal and vegetable oils. Non-corrosive and suitable for direct burial installation. These form seals fit Strain Relief Fittings made of other materials. (Nickel Plated rass, Stainless Steel, etc.) lso available with the following approvals: F 1 Nylon Liquid Tight Strain Relief Fittings ROMEX - PG/NPT/Metric s Part Numbers Slot Size imensions in Inches (mm) lack Gray F 1 Clearance ole ody s +.01 (+.25 mm) C16S-01 C16S x.55 (6 x 14) C16S-03 C16S-04 PG x.45 (5 x 11.5).88 (22.3) 1.10 (28).39 (10) 1.06 (27) C16S-05 C16S x.47 (7 x 12) C21S-01 C21S x.55 (6 x 14) PG 21 C21S-03 C21S x.55 (7 x 14) 1.12 (28.4) 1.22 (31).43 (11) 1.30 (33) C16NS-01 C16NS x.55 (6 x 14) C16NS-03 C16NS-04 1/2 NPT.20 x.45 (5 x 11.5) C16NS-05 C16NS x.47 (7 x 12) C21NS-01 C21NS x.55 (6 x 14) 3/4 NPT C21NS-03 C21NS x.55 (7 x 14) C20MS-01 C20MS x.55 (6 x 14) C20MS-03 C20MS-04 M20 x x.45 (5 x 11.5) C20MS-05 C20MS x.47 (7 x 12) C25MS-01 C25MS x.55 (6 x 14) M25 x 1.5 C25MS-03 C25MS x.55 (7 x 14) Suggested Clearance ole for Non-ed Mounting imensions and specifications may be changed without prior notice. Liquid Tight Strain Relief Fitting with nodized luminum Clamp for extra Pull-out Resistance Screw Clamp.83 (21.1) 1.10 (28).51 (13) 1.06 (27) 1.05 (26.7) 1.22 (31).55 (14) 1.30 (33).79 (20) 1.10 (28).35 (9) 1.06 (27).98 (25) 1.22 (31).43 (11) 1.30 (33) ROMEX is a federally registered trademark of Southwire Company. F 1 Suggested Clearance ole for Non-ed Mounting 9 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

10 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 10 Part Numbers imensions in Inches (mm) lack Gray No. iameter Part Numbers of of oles of Inserts only See page oles 49 for thread mm Inches Nylon Liquid Tight Strain Relief Fittings Multi-ole - PG s C161-K C161-GY To order, substitute CF for C (e.g. C091-K becomes CF091-K) C162-K C162-GY C163-K C163-GY ome Fittings also available with the following approvals: C164-K C164-GY C165-K C165-GY For specifications and C166-K C166-GY PG dimensions see page 4 C167-K C167-GY where the appropriate C168-K C168-GY Fittings are listed. C169-K C169-GY * C160-K C160-GY C16P-K C16P-GY Solid Insert *Note: This Insert has slotted holes. Silicone Viton Multi-ole Inserts are available in Silicone and Viton upon request. Viton is a federally registered trademark of upont ow Elastomer. imensions and specifications may be changed without prior notice. Part Numbers imensions in Inches (mm) lack Gray No. iameter of of oles oles Optional Locking Nuts, O-Rings & Other ccessories starting at page 28. Part Numbers of Inserts only See page 49 for thread mm Inches C07P-K C07P-GY PG 7 / Solid Insert C211-K C211-GY /4 NPT C212-K C212-GY C213-K C213-GY C091-K C091-GY C214-K C214-GY C092-K C092-GY C215-K C215-GY C093-K C093-GY PG 21 C216-K C216-GY C094-K C094-GY C217-K C217-GY C095-K C095-GY PG 9 C218-K C218-GY 4/1 5.2/3.7.20/ C096-K C096-GY C219-K C219-GY C097-K C097-GY C21P-K C21P-GY Solid Insert C098-K C098-GY C099-K C099-GY C291-K C291-GY C09P-K C09P-GY Solid Insert C292-K C292-GY PG 29 C293-K C293-GY C111-K C111-GY C29P-K C29P-GY Solid Insert C112-K C112-GY C113-K C113-GY PG 11 C361-K C361-GY C114-K C114-GY C362-K C362-GY C115-K C115-GY C363-K C363-GY PG C11P-K C11P-GY Solid Insert C364-K C364-GY C131-K C131-GY C36P-K C36P-GY Solid Insert C132-K C132-GY C421-K C421-GY C133-K C133-GY PG 42 C42P-K C42P-GY Solid Insert C134-K C134-GY C135-K C135-GY PG 13 C481-K C481-GY C136-K C136-GY C482-K C482-GY C137-K C137-GY PG 48 C483-K C483-GY C138-K C138-GY C48P-K C48P-GY Solid Insert C139-K C139-GY C13P-K C13P-GY Solid Insert Fittings with Multi-ole Inserts are also available with Flex Nut.

11 Part Numbers imensions in Inches (mm) lack Gray No. iameter Part Numbers of of oles of Inserts only See page oles 49 for thread mm Inches C07P-K C07P-GY PG 7 / 1/4 NPT Solid Insert Nylon Liquid Tight Strain Relief Fittings Multi-ole - NPT s imensions and specifications may be changed without prior notice. Part Numbers imensions in Inches (mm) lack Gray No. iameter of of oles oles Custom Solutions! ny special insert hole or profile configuration is available for a 1-time set-up fee & a minimum order of 1,000 pieces. For small quantities we suggest drilling or machining the inserts yourself, following these guidelines: Part Numbers of Inserts only See page 49 for thread mm Inches C21N1-K C21N1-GY C21N2-K C21N2-GY C21N3-K C21N3-GY C09N1-K C09N1-GY C21N4-K C21N4-GY C09N2-K C09N2-GY C21N5-K C21N5-GY C09N3-K C09N3-GY /4 NPT C21N6-K C21N6-GY C09N4-K C09N4-GY C21N7-K C21N7-GY C09N5-K C09N5-GY /8 NPT C21N8-K C21N8-GY 4/1 5.2/3.7.20/ C09N6-K C09N6-GY C21N9-K C21N9-GY C09N7-K C09N7-GY C21NP-K C21NP-GY Solid Insert C09N8-K C09N8-GY C09N9-K C09N9-GY C29N1-K C29N1-GY C09NP-K C09NP-GY Solid Insert C29N2-K C29N2-GY NPT C29N3-K C29N3-GY C13N1-K C13N1-GY C29NP-K C29NP-GY Solid Insert C13N2-K C13N2-GY C13N3-K C13N3-GY C29L1-K C29L1-GY C13N4-K C13N4-GY C29L2-K C29L2-GY 1-1/ C13N5-K C13N5-GY /2 NPT C29L3-K C29L3-GY NPT C13N6-K C13N6-GY C29LP-K C29LP-GY Solid Insert C13N7-K C13N7-GY C13N8-K C13N8-GY C36N1-K C36N1-GY C13N9-K C13N9-GY C36N2-K C36N2-GY C13NP-K C13NP-GY Solid Insert C36N3-K C36N3-GY 1-1/ NPT C36N4-K C36N4-GY C16N1-K C16N1-GY C36NP-K C36NP-GY Solid Insert C16N2-K C16N2-GY For specifications and dimensions see page 4 where the C16N3-K C16N3-GY appropriate Fittings are listed. C16N4-K C16N4-GY C16N5-K C16N5-GY C16N6-K C16N6-GY 1/2 NPT Silicone Viton (Enlarged) C16N7-K C16N7-GY C16N8-K C16N8-GY C16N9-K C16N9-GY * C16N0-K C16N0-GY C16NP-K C16NP-GY Solid Insert *Note: This Insert has slotted holes. Multi-ole Inserts are available in Silicone and Viton on request. Viton is a federally registered trademark of upont ow Elastomer. Fittings with Multi-ole Inserts are also available with Flex Nut. ome Fittings also available To order, substitute CF for C (e.g. C09N1-K becomes CF09N1-K) with the following approvals: We suggest drilling the frozen solid insert. rill holes by using a standard high-speed steel drill bit of the proper size at approx RPM. rill holes with insert installed in Strain Relief Fitting as a fixture. Keep a distance of min. 1 mm (.04 in) between holes. The outside holes can be located right against the lip of the strain relief body, as sufficient insert material remains between the hole and the body wall due to the design of the cord grip. Important: esign Parameters: Cable diameter should not be less than 80% of hole diameter and the difference between hole and cable diameter should never exceed.04 (1 mm). The Multi Cable fittings will meet NEM 4x = IP65 if the design parameters are complied with. To verify a submersible NEM 6= IP68 application, the final assembly of cables and fittings must be tested by the customer or submitted at the customer s expense to an independent test lab. 11 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

12 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 12 Part Numbers imensions in Inches (mm) lack Gray No. iameter Part Numbers of of oles of Inserts only See page oles 49 for thread mm Inches C12MP-K C12MP-GY M12 x 1.5 Solid Insert Nylon Liquid Tight Strain Relief Fittings Multi-ole - Metric s C16M1-K C16M1-GY C16M2-K C16M2-GY C16M3-K C16M3-GY C16M4-K C16M4-GY C16M5-K C16M5-GY M16 x 1.5 C16M6-K C16M6-GY C16M7-K C16M7-GY C16M8-K C16M8-GY C16M9-K C16M9-GY C16MP-K C16MP-GY Solid Insert C17M1-K C17M1-GY C17M2-K C17M2-GY C17M3-K C17M3-GY M16 x C17M4-K C17M4-GY (Enlarged) C17M5-K C17M5-GY C17MP-K C17MP-GY Solid Insert C20M1-K C20M1-GY C20M2-K C20M2-GY C20M3-K C20M3-GY C20M4-K C20M4-GY C20M5-K C20M5-GY M20 x 1.5 C20M6-K C20M6-GY C20M7-K C20M7-GY C20M8-K C20M8-GY C20M9-K C20M9-GY C20MP-K C20MP-GY Solid Insert C22M1-K C22M1-GY Fittings with Multi-ole Inserts are also available with Flex Nut. C22M2-K C22M2-GY To order, substitute CF for C C22M3-K C22M3-GY (e.g. C16M1-K becomes CF16M1-K) C22M4-K C22M4-GY C22M5-K C22M5-GY ome Fittings also available C22M6-K C22M6-GY M20 x 1.5 with the following approvals: (Enlarged) C22M7-K C22M7-GY C22M8-K C22M8-GY C22M9-K C22M9-GY * C22M0-K C22M0-GY Optional Locking Nuts, O-Rings & Other C22MP-K C22MP-GY Solid Insert ccessories starting at page 28. *Note: This Insert has slotted holes. ow to feed a cable assembly with plug through a strain relief fitting: 1. etermine largest dimension of the plug. 2. Choose Strain Relief with appropriate ome opening (see table on page 48). 3. rill solid insert to exact cable diameter & slice insert on one side only. 4. ssemble by feeding Connector first through dome nut and Strain Relief body, snap insert over cable and insert into body, tighten dome nut. one. 5. This applies to PG, NPT or Metric solutions. For specifications and dimensions see page 5 where the appropriate Fittings are listed. imensions and specifications may be changed without prior notice. Part Numbers imensions in Inches (mm) lack Gray No. iameter of of oles oles See page 49 for thread mm Inches Part Numbers of Inserts only C25M1-K C25M1-GY C25M2-K C25M2-GY C25M3-K C25M3-GY C25M4-K C25M4-GY C25M5-K C25M5-GY M25 x 1.5 C25M6-K C25M6-GY C25M7-K C25M7-GY C25M8-K C25M8-GY 4/1 5.2/3.7.20/ C25M9-K C25M9-GY C25MP-K C25MP-GY Solid Insert C32M1-K C32M1-GY C32M2-K C32M2-GY M32 x 1.5 C32M3-K C32M3-GY C32MP-K C32MP-GY Solid Insert C40M1-K C40M1-GY C40M2-K C40M2-GY C40M3-K C40M3-GY M40 x C40M4-K C40M4-GY C40MP-K C40MP-GY Solid Insert C50M1-K C50M1-GY M50 x C50MP-K C50MP-GY Solid Insert C63M1-K C63M1-GY C63M2-K C63M2-GY M63 x 1.5 C63M3-K C63M3-GY C63MP-K C63MP-GY Solid Insert

13 Features & enefits: Nickel Plated Nylon Liquid rass Liquid Tight Strain Tight Relief Strain Fittings Relief Fittings Features & enefits Liquid Tight - submersible to 300 ft. - NEM 4x & 6 (IP 68 / IP 69K) ighest pressure rating - Patented form seal meets 150 PSIG (10 bar) Flame protected - V0 rated according to UL 94 alogen- and Phosphorous free materials Safety - Ratchet to prevent ome from coming loose under vibration Large selection - Cable Range from.08 (2 mm) to 3.54 (90 mm) Non-Corrosive - Resistant to salt water, weak acids, weak alkalis, alcohol, esters, ketones, ether, gasoline, mineral, animal & vegetable oil. urable - Rugged Construction Environmentally compliant - RoS & eca E UL/UR E CS VE CGE ZERO UE114 PTENT Nickel Plated rass Nylon Strain Relief Your One Stop Solution For ll Cable & Wire ccessories! Unique Product Pull-out Resistance & Cable Protection Overlapping clamping splines apply a concentric force, thereby preventing the form seal from being pulled out of the fitting. This ensures pull-out protection without damage to the cable. Submersible The patented internal sealing edge results in a superior seal between the splined Nylon clamping insert and Nickel Plated rass body. ccessories Standard, Reduced and Multi-ole Inserts Modularity: increase and decrease cable opening by swapping out inserts to accommodate various cable sizes & configurations. imensions and specifications may be changed without prior notice. Unique Product The patented recess and high performance seal guarantees NEM 4x & 6 (IP 68 / IP 69K) at 150 PSIG (10 bar). Liquid Tight Molded O-Ring Groove: ll of our Nickel Plated rass parts come with an O-Ring, which makes your application liquid tight, allowing submersion up to 300 ft. Easy Installation The anti-rotation grooves prevent cable rotation while tightening the nut. Time Saving Installation Simply push the cable through Strain Relief Fitting - tighten ome or Flex Nut - one! No disassembly of the Fitting required: Insert Cable - Tighten Nut - Finished! Flex Nut The Stainless Steel spring extension offers superior protection against kinking and chafing of the cable. 13 dapter,reducer,enlarger

14 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 14 Part Numbers Cable Range ome Fittings Flex Fittings Nickel Plated rass Liquid Tight Strain Relief Fittings Standard - PG/NPT/Metric s Inches (mm) imensions in Inches (mm) C F 1 Clearance ole +.01 (+.25 mm) ody (ome) ody (Flex) imensions and specifications may be changed without prior notice. s C07-R CF07-R (3-6.5) PG 7 / C07R-R CF07R-R (2-5) 1/4 NPT.49 (12.5).75 (19) 2.17 (55).20 (5).55 (14) C09-R CF09-R (4-8) C09R-R CF09R-R (2-6) PG 9.60 (15.2).83 (21) 2.60 (66).24 (6).67 (17) C11-R CF11-R (5-10) C11R-R CF11R-R (3-7) PG (18.5).87 (22) 3.03 (77).24 (6).79 (20) C13-R CF13-R (6-12) C13R-R CF13R-R (5-9) PG (20.3).94 (24) 3.46 (88).26 (6.5).87 (22) C16-R CF16-R (10-14) C16R-R CF16R-R (7-12) PG (22.3).91 (23) 3.86 (98).26 (6.5).94 (24) C21-R CF21-R (13-18) C21R-R CF21R-R (9-16) PG (28.4).94 (24) 4.37 (111).28 (7) 1.18 (30) C29-R (18-25) C29R-R (13-20) PG (37.3) 1.14 (29) -.31 (8) 1.57 (40) C36-R (22-32) C36R-R (20-26) PG (47) 1.38 (35) -.31 (8) 1.97 (50) C42-R (32-38) C42R-R (25-31) PG (54.1) 1.46 (37) -.35 (9) 2.24 (57) C48-R (37-44) C48R-R (29-35) PG (59.4) 1.50 (38) -.39 (10) 2.52 (64) C09N-R CF09N-R (4-8) C09NR-R CF09NR-R (2-6) C13N-R CF13N-R (6-12) C13NR-R CF13NR-R (5-9) C16N-R CF16N-R (10-14) C16NR-R CF16NR-R (7-12) C21N-R CF21N-R (13-18) C21NR-R CF21NR-R (9-16) C29N-R (18-25) C29NR-R (13-20) 3/8 NPT.68 (17.2).83 (21) 2.60 (66).59 (15).67 (17) /.75 (19) 1/2 NPT.83 (21.1).94 (24) 3.46 (88).51 (13).87 (22) /.94 (24) 1/2 NPT.83 (21.1) 1.46 (37) 4.45 (113).51 (13).94 (24) 3/4 NPT 1.05 (26.7).98 (25) 4.37 (111).51 (13) 1.18 (30) 1 NPT 1.35 (34.3) 1.14 (29) -.75 (19) 1.57 (40) C12M-R CF12M-R (3-6.5) C12MR-R CF12MR-R (2-5) M12 x (12).75 (19) 2.17 (55).26 (6.5).55 (14) C16M-R CF16M-R (4-8) C16MR-R CF16MR-R (2-6) M16 x (16).83 (21) 2.60 (66).24 (6).67 (17) /.75 (19) C17M-R CF17M-R (5-10) C17MR-R CF17MR-R (3-7) M16 x (16).87 (22) 3.03 (77).24 (6).79 (20) C20M-R CF20M-R (6-12) C20MR-R CF20MR-R (5-9) M20 x (20).91 (23) 3.46 (88).24 (6).87 (22) C22M-R CF22M-R (10-14) C22MR-R CF22MR-R (7-12) M20 x (20).94 (24) 3.86 (98).24 (6).94 (24) C25M-R CF25M-R (13-18) C25MR-R CF25MR-R (9-16) M25 x (25) 1.02 (26) 4.37 (111).28 (7) 1.18 (30) C32M-R (18-25) C32MR-R (13-20) M32 x (32) 1.22 (31) -.31 (8) 1.57 (40) C40M-R (22-32) C40MR-R (20-26) M40 x (40) 1.46 (37) -.31 (8) 1.97 (50) C50M-R (32-38) C50MR-R (25-31) M50 x (50) 1.46 (37) -.35 (9) 2.24 (57) C63M-R (37-44) C63MR-R (29-35) M63 x (63) 1.50 (38) -.39 (10) 2.52 (64) / 2.68 (68) *Note: CS pproval only applies to ome Fittings. VE pproval only applies to Fittings with Metric. ome Fittings also available with the following approvals: * Suggested Clearance ole for Non-ed Mounting C Optional Locking Nuts & Other ccessories starting at page 28. F 1 F 1

15 Nickel Plated rass Liquid Tight Strain Relief Fittings Mini WI & WI XL - PG & Metric s Mini WI Fittings solve space restriction issues. These mini components will fit into tight areas, but maintain the quality of their larger counterparts. una-n or Viton O-Ring creates a reliable seal between body and housing. Mini WI Part Numbers Cable Range una-n Typical Mini pplications: Fiber optics Sensors Cameras Switches Small appliances Mini WI Part Numbers Cable Range una-n Viton Inches (mm) WI XL Typical XL pplications: Machine & pparatus utomation Railroads Ship uilding Off-shore Renewable Energy Utilities Nuclear Power imensions in Inches (mm) F 1 Clearance ole ody imensions in Inches (mm) F 1 Clearance ole +.01 (+.25 mm) ody CX52G-R (48-55) CX52G-R (53-60) G 2-1/ (75.2) 1.65 (42).71 (18) 3.54 (90) NG-52-XL G 2-1/2.28 (7) 3.15 (80) CX30G-R (58-65) 3.94 (100) G (87.9) 1.65 (42).71 (18) CX30G-R (63-70) 4.13 (105) NG-30-XL G 3.32 (8) 3.74 (95) CX40G-R (68-75) 4.92 (125) 2.05 (52).87 (22) CX40G-R (73-80) 4.92 (125) G (113) CX40GC-R (78-85) 4.92 (125) 2.05 (52).87 (22) CX40G-R (83-90) 5.12 (130) NG-40-XL G 4.43 (11) 4.92 (125) Viton is a federally registered trademark of upont ow Elastomer. 15 imensions and specifications may be changed without prior notice. s Inches (mm) +.01 (+.25 mm) CX63M-R (48-55) M63 x (63) 1.65 (42).39 (10) 2.95 (75) CX75M-R (48-55) 3.15 (80) M75 x (75) 1.65 (42).59 (15) CX75M-R (53-60) 3.35 (85) CX80M-R (58-65) M80 x (80) 1.65 (42).59 (15) 3.54 (90) CX90M-R (63-70) M90 x (90) 1.65 (42).59 (15) 3.94 (100) CX90M-R (68-75) CX10M-R (73-80) M100 x (100) 2.05 (52).79 (20) 4.33 (110) CX10M-R (78-85) CX11M-R (83-90) M110 x (110) 2.05 (52).79 (20) 4.72 (120) Suggested Clearance ole for Non-ed Mounting s C07W-R (2-4.5) PG 7.56 (14.3).56 (14.3).14 (3.5).59 (15) /.43 (11) C06MW-R C06MW-RV (2-3.2) M6 x 1.25 (6).39 (10).24 (6).31 (8) C08MW-R C08MW-RV (3-5) M8 x (8).51 (13).24 (6).43 (11) C10MW-R (4-6) M10 x (10).55 (14).24 (6).47 (12) WI XL Part Numbers F 1 Locknuts for Mini WI Locknuts for WI XL Part Numbers imensions in Inches (mm) G Thickness s NM-63-XL M63 x (6) 2.76 (70) NM-75-XL M75 x (8) 3.35 (85) NM-80-XL M80 x 2.32 (8) 3.54 (90) NM-90-XL M90 x 2.32 (8) 3.94 (100) NM-10-XL M100 x 2.43 (11) 4.53 (115) NM-11-XL M110 x 2.43 (11) 4.92 (125) imensions in Inches (mm) Thickness s NP-07-R PG 7.11 (2.8).59 (15) NM-06-R M6 x (2.5).39 (10) NM-08-R M8 x (2.5).51 (13) NM-10-R M10 x (2.8).51 (13) () Silicone or Viton Inserts & O-Rings for WI XL Fittings are available on request. For inquiries - please call our Inside Technical Sales epartment ( or ). F 1 G Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

16 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 16 Nickel Plated rass Liquid Tight Strain Relief Fittings * Elongated - PG & Metric s Part Numbers Cable Range ome Fittings Flex Fittings Inches (mm) C07C-R CF07C-R (3-6.5) C07CR-R CF07CR-R (2-5) C09C-R CF09C-R (4-8) C09CR-R CF09CR-R (2-6) C11C-R CF11C-R (5-10) C11CR-R CF11CR-R (3-7) C13C-R CF13C-R (6-12) C13CR-R CF13CR-R (5-9) C16C-R CF16C-R (10-14) C16CR-R CF16CR-R (7-12) C21C-R CF21C-R (13-18) C21CR-R CF21CR-R (9-16) C29C-R (18-25) C29CR-R (13-20) C36C-R (22-32) C36CR-R (20-26) C42C-R (32-38) C42CR-R (25-31) C48C-R (37-44) C48CR-R (29-35) ome Fittings also available with the following approvals: Optional Locking Nuts, O-Rings & other ccessories starting at page 28. C12-R CF12-R (3-6.5) C12R-R CF12R-R (2-5) C16-R CF16-R (4-8) C16R-R CF16R-R (2-6) C17-R CF17-R (5-10) C17R-R CF17R-R (3-7) C20-R CF20-R (6-12) C20R-R CF20R-R (5-9) C22-R CF22-R (10-14) C22R-R CF22R-R (7-12) C25-R CF25-R (13-18) C25R-R CF25R-R (9-16) C32-R (18-25) C32R-R (13-20) C40-R (22-32) C40R-R (20-26) C50-R (32-38) C50R-R (25-31) C63-R (37-44) C63R-R (29-35) imensions and specifications may be changed without prior notice. imensions in Inches (mm) C F 1 Clearance ole +.01 (+.25 mm) ody (ome) ody (Flex) s PG 7.49 (12.5).75 (19) 2.17 (55).39 (10).55 (14) PG 9.60 (15.2).83 (21) 2.60 (66).39 (10).67 (17) PG (18.5).87 (22) 3.03 (77).39 (10).79 (20) PG (20.3).94 (24) 3.46 (88).39 (10).87 (22) PG (22.3).91 (23) 3.86 (98).39 (10).94 (24) PG (28.4).94 (24) 4.37 (111).47 (12) 1.18 (30) PG (37.3) 1.14 (29) -.47 (12) 1.57 (40) PG (47) 1.38 (35) -.59 (15) 1.97 (50) PG (54.1) 1.46 (37) -.59 (15) 2.24 (57) PG (59.4) 1.50 (38) -.59 (15) 2.52 (64) Elongated is recommend where the Strain Relief has to pass through a thick wall or the application just needs the extra thread length. F 1 Wall Suggested Clearance ole for Non-ed Mounting M12 x (12).75 (19) 2.17 (55).39 (10).55 (14) M16 x (16).83 (21) 2.60 (66).39 (10).67 (17) /.75 (19) M16 x (16).87 (22) 3.03 (77).39 (10).79 (20) M20 x (20).91 (23) 3.46 (88).39 (10).87 (22) M20 x (20).94 (24) 3.86 (98).39 (10).94 (24) M25 x (25) 1.02 (26) 4.37 (111).47 (12) 1.18 (30) M32 x (32) 1.22 (31) -.47 (12) 1.57 (40) M40 x (40) 1.46 (37) -.59 (15) 1.97 (50) M50 x (50) 1.46 (37) -.59 (15) 2.24 (57) M63 x (63) 1.50 (38) -.59 (15) 2.52 (64) / 2.68 (68) C F 1 *Note: VE pproval only applies to Fittings with Metric. Wall

17 L min x 45º (1 x 45º) M20 x 1.5 / PG 13.5 Suggested Clearance ole for Non-ed Mounting.78 (19.8) L F F Nickel Plated rass Liquid Tight Strain Relief Fittings 90º Snap Elbow - PG & Metric s / Flange Part Numbers Cable Range w/ Connection s w/ Mounting Flange Inches (mm) E20M-R (10-14) E20MR-R (7-12) E13-R (10-14) E13R-R (7-12) - E20F-R (10-14) - E20FR-R (7-12).98 (25).78 (19.8).78 (19.8).13 (3.2) imensions in Inches (mm) L F Clearance ole +.01 (+.25 mm) ody ody s M20 x (20) 1.50 (38) 2.60 (66).30 (7.5).98 (25) PG (20.3) 1.50 (38) 2.60 (66).30 (7.5).98 (25) Flange.79 (20) 1.34 (34) 2.60 (66) -.98 (25) Robust - Compact - Low profile! Secure your connection today with these flange or threaded Snap Elbows. Saving on Space and Time during installation. Quick & Easy Installation: Insert cable into open Elbow, Snap closed, tighten dome nut for a liquid tight connection. - one! Nickel Plated rass Nylon Strain Relief * Part Numbers Cable Range Clamp Fittings Clamp Fittings w/ Standard Elongated Nickel Plated rass Liquid Tight Strain Relief Fittings Clamp igh Performance - PG/NPT/Metric s Inches (mm) imensions in Inches (mm) F 1 Clearance ole +.01 (+.25 mm) ody Standard Elongated imensions and specifications may be changed without prior notice. s C07-MZ C07C-MZ (3-6.5) PG 7.49 (12.5) 1.02 (26).20 (5).39 (10).55 (14) C09-MZ C09C-MZ (4-8) PG 9.60 (15.2) 1.10 (28).24 (6).39 (10).67 (17) C11-MZ C11C-MZ (6-10) PG (18.5) 1.18 (30).24 (6).39 (10).79 (20) C13-MZ C13C-MZ (6-12) PG (20.3) 1.30 (33).25 (6.5).39 (10).87 (22) C16-MZ C16C-MZ (10-14) PG (22.3) 1.30 (33).25 (6.5).39 (10).94 (24) C21-MZ C21C-MZ (13-18) PG (28.4) 1.46 (37).28 (7).47 (12) 1.18 (30) C29-MZ C29C-MZ (20-25) PG (37.3) 1.69 (43).31 (8).47 (12) 1.57 (40) C36-MZ C36C-MZ (24-32) PG (47) 1.97 (50).31 (8).59 (15) 1.97 (50) C42-MZ C42C-MZ (32-38) PG (54.1) 2.01 (51).35 (9).59 (15) 2.24 (57) C48-MZ C48C-MZ (37-44) PG (59.4) 2.05 (52).39 (10).59 (15) 2.52 (64) C09N-MZ (4-8) 3/8 NPT.68 (17.2) 1.10 (28).59 (15) -.67 (17) /.75 (19) C13N-MZ (7-12) 1/2 NPT.83 (21.1) 1.30 (33).51 (13) -.87 (22) /.94 (24) C21N-MZ (13-18) 3/4 NPT 1.05 (26.7) 1.46 (37).51 (13) (30) C29N-MZ (18-25) 1 NPT 1.35 (34.3) 1.69 (43).75 (19) (40) C12M-MZ C12-MZ (3-6.5) M12 x (12) 1.02 (26).26 (6.5).39 (10).55 (14) C16M-MZ C16-MZ (4-8) M16 x (16) 1.10 (28).24 (6).39 (10).75 (19) C17M-MZ C17-MZ (6-10) M16 x (16) 1.18 (30).24 (6).39 (10).79 (20) C20M-MZ C20-MZ (6-12) M20 x (20) 1.30 (33).24 (6).39 (10).87 (22) C22M-MZ C22-MZ (10-14) M20 x (20) 1.30 (33).24 (6).39 (10).94 (24) C25M-MZ C25-MZ (13-18) M25 x (25) 1.46 (37).28 (7).47 (12) 1.18 (30) C32M-MZ C32-MZ (18-25) M32 x (32) 1.69 (43).31 (8).47 (12) 1.57 (40) C40M-MZ C40-MZ (22-32) M40 x (40) 1.97 (50).31 (8).59 (15) 1.97 (50) C50M-MZ C50-MZ (32-38) C50MR-MZ C50R-MZ (25-31) M50 x (50) 2.01 (51).35 (9).59 (15) 2.24 (57) C63M-MZ C63-MZ (37-44) M63 x (63) 2.05 (52).39 (10).59 (15) 2.52 (64) / C63MR-MZ C63R-MZ (29-35) 2.68 (68) *Note: VE pproval only applies to Fittings with Metric. igh Performance Liquid Tight Strain Relief Fitting - The Clamping Nut provides extra Pull-out Resistance. Screw Clamp Suggested Clearance ole for Non-ed Mounting F 1 17 ccessories dapter,reducer,enlarger

18 Nickel Plated rass Nylon Strain Relief Nickel Plated rass Liquid Tight Strain Relief Fittings EMI/RFI Proof - Product Features EMI (Electromagnetic Interference) / RFI (Radio Frequency Interference) is an unwanted disturbance that affects an electrical circuit due to either electromagnetic conduction or electromagnetic radiation emitted from an external source. The disturbance may interrupt, obstruct, or otherwise limit the effective performance of the circuit. These Liquid Tight EMI / RFI - Proof Grounded Strain Relief Fittings made of Nickel Plated rass are the perfect answer to stringent requirements for reliable grounding and protection from electromagnetic interference. Two styles are available: Standard and Feed-Through. Standard (-E) The Standard version has an integral O-ring, which presses the braiding against the inside wall of the body but can only be used with braided shield. ccessories Overlapping clamping splines apply a concentric force, thereby preventing the form seal from being pulled out of the fitting. This ensures pull-out protection without damage to the cable. dapter,reducer,enlarger 18 Feed-Through (-FE) The patented internal sealing edge results in a superior seal between the splined Nylon clamping insert and Nickel Plated rass body. Patented 360º grounding due to the internal O-Ring, which ensures perfect contact between braided shield of cable and fitting. Feed-Through works well with braided or foil shield and provides reliable grounding by means of metal spring fingers. Overlapping clamping splines apply a concentric force, thereby preventing the form seal from being pulled out of the fitting. This ensures pull-out protection without damage to the cable. Metal-coated spline insert provides electrical conductivity. Flexible contact points allow contact with variable braid and foil diameters and add additional strain relief to a solution. imensions and specifications may be changed without prior notice.

19 Nickel Plated rass Liquid Tight Strain Relief Fittings EMI/RFI Proof - pplications & ssembly alogen and Phosphorous-Free Fire Protection Class V0 ccording to UL 94 Liquid Tight per NEM 4x & 6 to 150 PSIG (IP 68 to 10 bar) Quick ssembly and Reliable Grounding of raid or Foil Shielded Cables EMI/RFI Proof Strain Relief Fittings in all popular thread types and sizes are used in the following areas: Telecommunication Measuring, control and feedback systems Control panels Traffic, etc. Nickel Plated rass Nylon Strain Relief lso used in all areas where in addition to a reliable liquid tight seal, high pull-out resistance and anti-rotation provisions, a dependable contact with the cable shield is required. To ensure a good ground connection between the Cord Grip and a Metal Enclosure, we strongly recommend the use of EMI/RFI Locking Nuts (Page 29) for non-threaded mounting. ccessories Standard (-E) Step 1 Strip cable Expose braided shield Step 2 Feed cable through dome nut & clamping insert Fold braided shield back over O-Ring on clamping insert Make sure that braided shield overlaps the O-ring by 3/32 (2 mm) only Step 3 Push clamping insert into body Tighten dome nut Finished ssembly Instructions imensions and specifications may be changed without prior notice. These Locking Nuts have cutting edges which will slice through paint and coatings into the metal of the enclosure to ensure grounding. (see page 29) Feed-Through (-FE) Option 1 - Partial Jacket Stripping: Expose shield approximately 7/16 (10 mm) Insert cable into fitting until the braid or foil reaches the contact position Tighten the dome nut Finished Option 2 - Total Jacket Removed: Remove cable jacket to expose the braid or foil Insert cable into fitting until the braid reaches the contact point Tighten the dome nut Finished Option 3 - Fold Shield over Jacket: Strip cable jacket & braiding to different lengths For smaller cable diameters fold the braided shield back over the cable jacket Insert cable into fitting until the braid reaches the contact point Tighten the dome nut Finished Questions or concerns? - Please call our well-trained Inside Technical Sales epartment ( or ). 19 dapter,reducer,enlarger

20 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 20 ome Fittings Standard * Nickel Plated rass Liquid Tight Strain Relief Fittings EMI/RFI Proof - PG/NPT/Metric & Elongated s EMI/RFI Proof - Grounded: Standard Version (-E) Part Numbers Cable Range Flex Fittings ome Fittings Flex Fittings Standard Elongated Elongated Inches (mm) imensions and specifications may be changed without prior notice. imensions in Inches (mm) C F 1 Clearance ole +.01 (+.25 mm) ody (ome) ody (Flex) Standard Elongated C07-E CF07-E C07C-E CF07C-E (3-6.5) PG 7 / C07R-E CF07R-E C07CR-E CF07CR-E (2-5) 1/4 NPT.49 (12.5).75 (19) 2.17 (55).20 (5).39 (10).55 (14) C09-E CF09-E C09C-E CF09C-E (4-8) C09R-E CF09R-E C09CR-E CF09CR-E (2-6) PG 9.60 (15.2).83 (21) 2.60 (66).24 (6).39 (10).67 (17) C11-E CF11-E C11C-E CF11C-E (5-10) C11R-E CF11R-E C11CR-E CF11CR-E (3-7) PG (18.5).87 (22) 3.03 (77).24 (6).39 (10).79 (20) C13-E CF13-E C13C-E CF13C-E (6-12) C13R-E CF13R-E C13CR-E CF13CR-E (5-9) PG (20.3).94 (24) 3.46 (88).26 (6.5).39 (10).87 (22) C16-E CF16-E C16C-E CF16C-E (10-14) C16R-E CF16R-E C16CR-E CF16CR-E (7-12) PG (22.3).91 (23) 3.86 (98).26 (6.5).39 (10).94 (24) C21-E CF21-E C21C-E CF21C-E (13-18) C21R-E CF21R-E C21CR-E CF21CR-E (9-16) PG (28.4).94 (24) 4.37 (111).28 (7).47 (12) 1.18 (30) C29-E - C29C-E (18-25) C29R-E - C29CR-E (13-20) PG (37.3) 1.14 (29) -.31 (8).47 (12) 1.57 (40) C36-E - C36C-E (22-32) C36R-E - C36CR-E (20-26) PG (47) 1.38 (35) -.31 (8).59 (15) 1.97 (50) C42-E - C42C-E (32-38) C42R-E - C42CR-E (25-31) PG (54.1) 1.46 (37) -.35 (9).59 (15) 2.24 (57) C48-E - C48C-E (37-44) C48R-E - C48CR-E (29-35) PG (59.4) 1.50 (38) -.39 (10).59 (15) 2.52 (64) C09N-E CF09N-E (4-8) C09NR-E CF09NR-E (2-6) C13N-E CF13N-E (6-12) C13NR-E CF13NR-E (5-9) C21N-E CF21N-E (13-18) C21NR-E CF21NR-E (9-16) 3/8 NPT.68 (17.2).83 (21) 2.60 (66).59 (15) - 1/2 NPT.83 (21.1).94 (24) 3.46 (88).51 (13) - s.67 (17) /.75 (19).87 (22) /.94 (24) 3/4 NPT 1.05 (26.7).98 (25) 4.37 (111).51 (13) (30) C12M-E CF12M-E C12-E CF12-E (3-6.5) C12MR-E CF12MR-E C12R-E CF12R-E (2-5) M12 x (12).75 (19) 2.17 (55).26 (6.5).39 (10).55 (14) C16M-E CF16M-E C16-E CF16-E (5-10) C16MR-E CF16MR-E C16R-E CF16R-E (3-7) M16 x (16).87 (22) 3.03 (77).24 (6).39 (10).79 (20) C20M-E CF20M-E C20-E CF20-E (10-14) C20MR-E CF20MR-E C20R-E CF20R-E (7-12) M20 x (20).91 (23) 3.86 (98).24 (6).39 (10).94 (24) C25M-E CF25M-E C25-E CF25-E (13-18) C25MR-E CF25MR-E C25R-E CF25R-E (9-16) M25 x (25).94 (24) 4.37 (111).28 (7).47 (12) 1.18 (30) C32M-E - C32-E (18-25) C32MR-E - C32R-E (13-20) M32 x (32) 1.22 (31) -.31 (8).47 (12) 1.57 (40) C40M-E - C40-E (22-32) C40MR-E - C40R-E (20-26) M40 x (40) 1.46 (37) -.31 (8).59 (15) 1.97 (50) C50M-E (32-38) C50MR-E (25-31) M50 x (50) 1.46 (37) -.35 (9) (57) C63M-E (37-44) M63 x (63) 1.50 (38) -.39 (10) (64) / C63MR-E (29-35) 2.68 (68) *Note: VE pproval only applies to Fittings with Metric. UL, UR & CS pproval applies to ome Fittings. EMI/RFI Fittings are also available with igh Performance Clamp or in Stainless Steel. For inquiries - please call our Inside Technical Sales epartment ( or ). ome Fittings also available with the following approvals:

21 Nickel Plated rass Liquid Tight Strain Relief Fittings EMI/RFI Proof - PG/NPT/Metric & Elongated s EMI/RFI Proof - Grounded: Feed-Through Version (-FE) Part Numbers Cable Range ome Fittings ome Fittings Standard Elongated Inches (mm) imensions in Inches (mm) F 1 Clearance ole +.01 (+.25 mm) ody Standard Elongated C07-FE (3-6.5) PG 7 / 1/4 NPT.49 (12.5).94 (24).20 (5) -.55 (14) C09-FE (4-8) PG 9.60 (15.2) 1.10 (28).24 (6) -.67 (17) C11-FE (5-10) PG (18.5) 1.14 (29).24 (6) -.79 (20) C13-FE (6-12) PG (20.3) 1.22 (31).26 (6.5) -.87 (22) C16-FE (10-14) PG (22.3) 1.26(32).26 (6.5) -.94 (24) C21-FE (13-18) PG (28.4) 1.50 (38).28 (7) (30) C29-FE (18-25) PG (37.3) 1.69 (43).31 (8) (40) C36-FE (24-32) PG (47) 1.89 (48).31 (8) (50) C42-FE (32-38) PG (54.1) 1.77 (45).35 (9) (57) C48-FE (37-44) PG (59.4) 1.81 (46).39 (10) (64) s Nickel Plated rass Nylon Strain Relief C09N-FE (4-8) 3/8 NPT.68 (17) 1.14 (29).59 (15) -.67 (17) /.75 (19) C13N-FE (6-12) 1/2 NPT.83 (21) 1.30 (33).51 (13) -.87 (22) /.94 (24) C21N-FE (13-18) 3/4 NPT 1.05 (27) 1.54 (39).51 (13) (30) C12M-FE C12-FE (3-6.5) M12 x (12).98 (25).26 (6.5).39 (10).55 (14) C16M-FE C16-FE (5-10) M16 x (16) 1.26 (32).24 (6).39 (10).79 (20) C16MR-FE C16R-FE (4-8) M16 x (16) 1.14 (29).24 (6).39 (10).67 (17) /.75 (19) C20M-FE C20-FE (10-14) M20 x (20) 1.30 (33).24 (6).39 (10).94 (24) C20MR-FE C20R-FE (6-12) M20 x (20) 1.28 (32.5).24 (6).39 (10).87 (22) C25M-FE C25-FE (13-18) M25 x (25) 1.54 (39).28 (7).47 (12) 1.18 (30) C32M-FE C32-FE (18-25) M32 x (32) 1.77 (45).31 (8).47 (12) 1.57 (40) C40M-FE C40-FE (22-32) M40 x (40) 2.01 (51).31 (8).59 (15) 1.97 (50) C50M-FE (32-38) M50 x (50) 2.24 (57.5).35 (9) (57) C63M-FE (37-44) M63 x (63) 2.05 (52).39 (10) (64) / 2.68 (68) Feed-Through products are Quick, Reliable & Labor saving! Partial Jacket Stripping Total Jacket Removal Fold Shield Over Jacket Use our recommened EMI Locking Nuts with cutting edges which will cut through paint to ensure proper grounding. (see page 29) lso available with the following approvals: Optional Locking Nuts, O-Rings & Other ccessories starting at page 28. imensions and specifications may be changed without prior notice. F 1 Suggested Clearance ole for Non-ed Mounting 21 ccessories dapter,reducer,enlarger

22 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 22 Nickel Plated rass Liquid Tight Strain Relief Fittings Multi-ole - PG s Part Numbers imensions in Inches (mm) ome Fittings Flex Fittings No. iameter Part Numbers of of oles of Inserts only See page oles 49 for thread mm Inches C07P-R CF07P-R PG 7 / 1/4 NPT Solid Insert C091-R CF091-R C092-R CF092-R C093-R CF093-R C094-R CF094-R C095-R CF095-R PG 9 C096-R CF096-R C097-R CF097-R C098-R CF098-R C099-R CF099-R C09P-R CF09P-R Solid Insert C111-R CF111-R C112-R CF112-R C113-R CF113-R PG 11 C114-R CF114-R C115-R CF115-R C11P-R CF11P-R Solid Insert C131-R CF131-R C132-R CF132-R C133-R CF133-R C134-R CF134-R C135-R CF135-R PG 13 C136-R CF136-R C137-R CF137-R C138-R CF138-R C139-R CF139-R C13P-R CF13P-R Solid Insert C161-R CF161-R C162-R CF162-R C163-R CF163-R C164-R CF164-R C165-R CF165-R C166-R CF166-R PG C167-R CF167-R C168-R CF168-R C169-R CF169-R * C160-R CF160-R C16P-R CF16P-R Solid Insert *Note: This Insert has slotted holes. Silicone Viton Part Numbers imensions in Inches (mm) ome Fittings Flex Fittings No. iameter of of oles oles imensions and specifications may be changed without prior notice. Part Numbers of Inserts only See page 49 for thread mm Inches C211-R CF211-R C212-R CF212-R C213-R CF213-R C214-R CF214-R C215-R CF215-R PG 21 C216-R CF216-R C217-R CF217-R C218-R CF218-R 4/1 5.2/3.7.20/ C219-R CF219-R C21P-R CF21P-R Solid Insert C291-R C292-R PG 29 C293-R C29P-R - Solid Insert C361-R C362-R C363-R - PG C364-R C36P-R - Solid Insert C421-R PG 42 C42P-R - Solid Insert C481-R C482-R PG 48 C483-R C48P-R - Solid Insert For specifications and dimensions see page 14 where the appropriate Fittings are listed. Optional Locking Nuts & Other ccessories starting at page 28. Viton is a federally registered trademark of upont ow Elastomer. ome Fittings also available with the following approvals:

23 Nickel Plated rass Liquid Tight Strain Relief Fittings Multi-ole - NPT s Part Numbers imensions in Inches (mm) ome Fittings Flex Fittings No. iameter Part Numbers of of oles of Inserts only See page oles 49 for thread mm Inches C07P-R CF07P-R PG 7 / 1/4 NPT Solid Insert C09N1-R CF09N1-R C09N2-R CF09N2-R C09N3-R CF09N3-R C09N4-R CF09N4-R C09N5-R CF09N5-R /8 NPT C09N6-R CF09N6-R C09N7-R CF09N7-R C09N8-R CF09N8-R C09N9-R CF09N9-R C09NP-R CF09NP-R Solid Insert C13N1-R CF13N1-R C13N2-R CF13N2-R C13N3-R CF13N3-R C13N4-R CF13N4-R C13N5-R CF13N5-R /2 NPT C13N6-R CF13N6-R C13N7-R CF13N7-R C13N8-R CF13N8-R C13N9-R CF13N9-R C13NP-R CF13NP-R Solid Insert C16N1-R CF16N1-R C16N2-R CF16N2-R C16N3-R CF16N3-R C16N4-R CF16N4-R C16N5-R CF16N5-R C16N6-R CF16N6-R 1/2 NPT (Enlarged) C16N7-R CF16N7-R C16N8-R CF16N8-R C16N9-R CF16N9-R * C16N0-R CF16N0-R C16NP-R CF16NP-R Solid Insert *Note: This Insert has slotted holes. Custom Solutions! imensions and specifications may be changed without prior notice. Part Numbers imensions in Inches (mm) ome Fittings Flex Fittings No. iameter of of oles oles Part Numbers of Inserts only C29N1-R C29N2-R NPT C29N3-R C29NP-R - Solid Insert For specifications and dimensions see page 14 where the appropriate Fittings are listed. ome Fittings also available with the following approvals: ny special insert hole or profile configuration is available for a 1-time set-up fee & a minimum order of 1,000 pieces. For small quantities we suggest drilling or machining the inserts yourself, following these guidelines: We suggest drilling the frozen solid Insert. rill holes by using a standard high-speed steel drill bit of the proper size at approx RPM. rill holes with insert installed in Strain Relief Fitting as a fixture. Keep a distance of min. 1 mm (.04 in) between holes. The outside holes can be located right against the lip of the strain relief body, as sufficient insert material remains between the hole and the body wall due to the design of the cord grip. Important: See page 49 for thread mm Inches C21N1-R CF21N1-R C21N2-R CF21N2-R C21N3-R CF21N3-R C21N4-R CF21N4-R C21N5-R CF21N5-R /4 NPT C21N6-R CF21N6-R C21N7-R CF21N7-R C21N8-R CF21N8-R 4/1 5.2/3.7.20/ C21N9-R CF21N9-R C21NP-R CF21NP-R Solid Insert Optional Locking Nuts & Other ccessories starting at page 28. Multi-ole Inserts are available in Silicone and Viton on request. Viton is a federally registered trademark of upont ow Elastomer. Silicone Viton esign Parameters: Cable diameter should not be less than 80% of hole diameter and the difference between hole and cable diameter should never exceed.04 (1 mm). The Multi Cable fittings will meet NEM 4x = IP65 if the design parameters are complied with. To verify a submersible NEM 6= IP68 application, the final assembly of cables and fittings must be tested by the customer or submitted at the customer s expense to an independent test lab. 23 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

24 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 24 Nickel Plated rass Liquid Tight Strain Relief Fittings Multi-ole - Metric s Part Numbers imensions in Inches (mm) ome Fittings Flex Fittings No. iameter Part Numbers of of oles of Inserts only See page oles 49 for thread mm Inches C12MP-R CF12MP-R M12 x 1.5 Solid Insert C16M1-R CF16M1-R C16M2-R CF16M2-R C16M3-R CF16M3-R C16M4-R CF16M4-R C16M5-R CF16M5-R M16 x 1.5 C16M6-R CF16M6-R C16M7-R CF16M7-R C16M8-R CF16M8-R C16M9-R CF16M9-R C16MP-R CF16MP-R Solid Insert C17M1-R CF17M1-R C17M2-R CF17M2-R C17M3-R CF17M3-R M16 x C17M4-R CF17M4-R (Enlarged) C17M5-R CF17M5-R C17MP-R CF17MP-R Solid Insert C20M1-R CF20M1-R C20M2-R CF20M2-R C20M3-R CF20M3-R C20M4-R CF20M4-R C20M5-R CF20M5-R M20 x 1.5 C20M6-R CF20M6-R C20M7-R CF20M7-R C20M8-R CF20M8-R C20M9-R CF20M9-R C20MP-R CF20MP-R Solid Insert C22M1-R CF22M1-R C22M2-R CF22M2-R C22M3-R CF22M3-R C22M4-R CF22M4-R C22M5-R CF22M5-R C22M6-R CF22M6-R M20 x (Enlarged) C22M7-R CF22M7-R C22M8-R CF22M8-R C22M9-R CF22M9-R * C22M0-R CF22M0-R C22MP-R CF22MP-R Solid Insert *Note: This Insert has slotted holes. ow to feed a cable assembly with plug through a strain relief fitting: 1. etermine largest dimension of the plug. 2. Choose Strain Relief with appropriate ome opening (see table on page 48). 3. rill solid insert to exact cable diameter & slice insert on one side only. 4. ssemble by feeding Connector first through dome nut and Strain Relief body, snap insert over cable and insert into body, tighten dome nut. one. 5. This applies to PG, NPT or Metric solutions. Part Numbers imensions in Inches (mm) ome Fittings Flex Fittings No. iameter of of oles oles imensions and specifications may be changed without prior notice. mm Inches Part Numbers of Inserts only C25M1-R CF25M1-R C25M2-R CF25M2-R C25M3-R CF25M3-R C25M4-R CF25M4-R C25M5-R CF25M5-R M25 x 1.5 C25M6-R CF25M6-R C25M7-R CF25M7-R C25M8-R CF25M8-R 4/1 5.2/3.7.20/ C25M9-R CF25M9-R C25MP-R CF25MP-R Solid Insert C32M1-R C32M2-R M32 x 1.5 C32M3-R C32MP-R - Solid Insert C40M1-R C40M2-R C40M3-R - M40 x C40M4-R C40MP-R - Solid Insert C50M1-R M50 x 1.5 C50MP-R - Solid Insert C63M1-R C63M2-R M63 x 1.5 C63M3-R C63MP-R - Solid Insert For specifications and dimensions see page 14 where the appropriate Fittings are listed. ome Fittings also available with the following approvals: See page 49 for thread Optional Locking Nuts & Other ccessories starting at page 28.

25 * Nylon Liquid Tight Strain Relief Fittings PVF - Teflon - PG/NPT/Metric s Viton - igh/low Temperatures & Chemical Resistant Part Numbers Cable Range ome Fittings Flex Fittings Inches (mm) C07-TE CF07-TE (3-6.5) C07R-TE CF07R-TE (2-5) C09-TE CF09-TE (4-8) C09R-TE CF09R-TE (2-6) C11-TE (5-10) C11R-TE (3-7) C13-TE CF13-TE (6-12) C13R-TE CF13R-TE (5-9) C16-TE (10-14) C16R-TE (7-12) C21-TE (13-18) C21R-TE (9-16) C29-TE (18-25) C29R-TE (13-20) C36-TE (22-32) C36R-TE (20-26) C42-TE (32-38) C42R-TE (25-31) C48-TE (37-44) C48-TE (29-35) PG 7 / 1/4 NPT imensions in Inches (mm) C F 1 Clearance ole +.01 (+.25 mm) ody (ome) ody (Flex) s.49 (12.5).83 (21) 2.13 (54).31 (8).59 (15) PG 9.60 (15.2).87 (22) 2.48 (63).31 (8).75 (19) PG (18.5).98 (25) -.31 (8).87 (22) PG (20.3) 1.06 (27) 3.54 (90).35 (9).94 (24) PG (22.3) 1.10 (28) -.39 (10) 1.06 (27) PG (28.4) 1.22 (31) -.43 (11) 1.30 (33) PG (37.3) 1.54 (39) -.43 (11) 1.65 (42) PG (47) 1.89 (48) -.51 (13) 2.09 (53) PG (54.1) 1.93 (49) -.51 (13) 2.36 (60) PG (59.4) 1.93 (49) -.55 (14) 2.56 (65) Nickel Plated rass Nylon Strain Relief ccessories C09N-TE CF09N-TE (4-8) C09NR-TE CF09NR-TE (2-6) C13N-TE CF13N-TE (6-12) C13NR-TE CF13NR-TE (5-9) C16N-TE (10-14) C16NR-TE (7-12) C21N-TE (13-18) C21NR-TE (9-16) C12M-TE CF12M-TE (3-6.5) C12MR-TE CF12MR-TE (2-5) C16M-TE CF16M-TE (4-8) C16MR-TE CF16MR-TE (2-6) C20M-TE CF20M-TE (6-12) C20MR-TE CF20MR-TE (5-9) C25M-TE (13-18) C25MR-TE (9-16) C32M-TE (18-25) C32MR-TE (13-20) *Note: VE pproval only applies to Fittings with Metric. C F 1 Ideal for: 3/8 NPT.68 (17.2).87 (22) 2.13 (54).59 (15) imensions imensions and specifications and specifications may be may changed be changed without without prior notice. prior notice..87 (22) /.75 (19) 1/2 NPT.83 (21.1) 1.06 (27) 2.48 (63).51 (13).94 (24) 1/2 NPT.83 (21.1) 1.10 (28) -.51 (13) 1.06 (27) 3/4 NPT 1.05 (26.7) 1.22 (31) -.55 (14) 1.30 (33) M12 x (12).83 (21) 2.13 (54).31 (8).59 (15) M16 x (16).87 (22) 2.48 (63).31 (8).75 (19) M20 x (20) 1.06 (27) 3.54 (90).35 (9).94 (24) M25 x (25) 1.22 (31) -.43 (11) 1.30 (33) M32 x (32) 1.54 (39) -.43 (11) 1.65 (42) Food & everage Industries Clean Room pplications igh Temperature pplications F 1 Suggested Clearance ole for Non-ed Mounting Viton and Teflon are federally registered trademarks of upont ow Elastomer. Optional Locking Nuts, O-Rings & Other ccessories starting at page dapter,reducer,enlarger

26 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 26 * Nickel Plated Liquid rass Tight Liquid Strain Tight Relief Strain Fittings Relief Fittings PVF - Nickel Pl. rass - PG/NPT/Metric & Elongated C12M-RV C12-RV (3-6.5) C12MR-RV C12R-RV (2-5) M12 x (12).75 (19).26 (6.5).39 (10).55 (14) C16M-RV C16-RV (4-8) M16 x (16).83 (21).24 (6).39 (10).67 (17) / C16MR-RV C16R-RV (2-6).75 (19) C17M-RV C17-RV (5-10) C17MR-RV C17R-RV (3-7) M16 x (16).87 (22).24 (6).39 (10).79 (20) C20M-RV C20-RV (6-12) C20MR-RV C20-RV (5-9) M20 x (20).91 (23).24 (6).39 (10).87 (22) C22M-RV C22-RV (10-14) C22MR-RV C22R-RV (7-12) M20 x (20).94 (24).24 (6).39 (10).94 (24) C25M-RV C25-RV (13-18) C25MR-RV C25R-RV (9-16) M25 x (25) 1.02 (26).28 (7).47 (12) 1.18 (30) C32M-RV C32-RV (18-25) C32MR-RV C32R-RV (13-20) M32 x (32) 1.22 (31).31 (8).47 (12) 1.57 (40) C40M-RV C40-RV (22-32) C40MR-RV C40R-RV (20-26) M40 x (40) 1.46 (37).31 (8).59 (15) 1.97 (50) Viton is a federally registered trademark of upont ow Elastomer. *Note: VE pproval only applies to Fittings with Metric. lso available with the following approvals: Viton - igh/low Temperatures & Chemical Resistant Part Numbers Cable Range ome Fittings ome Fittings Standard Elongated Inches (mm) igh Performance Extreme Temperatures Sturdy imensions in Inches (mm) F 1 Clearance ole +.01 (+.25 mm) ody Standard imensions and specifications may be changed without prior notice. Elongated s C07-RV C07C-RV (3-6.5) PG 7 / C07R-RV C07CR-RV (2-5) 1/4 NPT.49 (12.5).75 (19).20 (5).39 (10).55 (14) C09-RV C09C-RV (4-8) C09R-RV C09CR-RV (2-6) PG 9.60 (15.2).83 (21).24 (6).39 (10).67 (17) C11-RV C11C-RV (5-10) C11R-RV C11CR-RV (3-7) PG (18.5).87 (22).24 (6).39 (10).79 (20) C13-RV C13C-RV (6-12) C13R-RV C13CR-RV (5-9) PG (20.3).94 (24).26 (6.5).39 (10).87 (22) C16-RV C16C-RV (10-14) C16R-RV C16CR-RV (7-12) PG (22.3).91 (23).26 (6.5).47 (12).94 (24) C21-RV C21C-RV (13-18) C21R-RV C21CR-RV (9-16) PG (28.4).94 (24).28 (7).47 (12) 1.18 (30) C29-RV C29C-RV (18-25) C29R-RV C29CR-RV (13-20) PG (37.3) 1.14 (29).31 (8).47 (12) 1.57 (40) C36-RV C36C-RV (22-32) C36R-RV C36CR-RV (20-26) PG (47) 1.38 (35).31 (8).59 (15) 1.97 (50) C42-RV C42C-RV (32-38) C42R-RV C42CR-RV (25-31) PG (54.1) 1.46 (37).35 (9).59 (15) 2.24 (57) C48-RV C48C-RV (37-44) C48-RV C48C-RV (29-35) PG (59.4) 1.50 (38).39 (10).59 (15) 2.52 (64) C09N-RV (4-8) C09NR-RV (2-6) C13N-RV (6-12) C13NR-RV (5-9) C21N-RV (13-18) C21NR-RV (9-16) 3/8 NPT.68 (17.2).83 (21).59 (15) - 1/2 NPT.83 (21.1).94 (24).51 (13) -.67 (17) /.75 (19).87 (22) /.94 (24) 3/4 NPT.83 (21.1).98 (25).51 (13) (30) F 1 Suggested Clearance ole for Non-ed Mounting

27 * Nickel Plated Liquid rass Tight Liquid Strain Tight Relief Strain Fittings Relief Fittings 303 Stainless Steel - PG/NPT/Metric s igh Performance, igh/low Temperatures & Corrosion Resistant Part Numbers Cable Range Standard PVF Inches (mm) C07-SS C07-SV (3-6.5) C07R-SS C07R-SV (2-5) C09-SS C09-SV (4-8) C09R-SS C09R-SV (2-6) C11-SS C11-SV (5-10) C11R-SS C11R-SV (3-7) C13-SS C13-SV (6-12) C13R-SS C13R-SV (5-9) C16-SS C16-SV (10-14) C16R-SS C16R-SV (7-12) C21-SS C21-SV (13-18) C21R-SS C21R-SV (9-16) C29-SS C29-SV (18-25) C29R-SS C29R-SV (13-20) C36-SS C36-SV (22-32) C36R-SS C36R-SV (20-26) C09N-SS C09N-SV (4-8) C09NR-SS C09NR-SV (2-6) C13N-SS C13N-SV (6-12) C13NR-SS C13NR-SV (5-9) C21N-SS C21N-SV (13-18) C21NR-SS C21NR-SV (9-16) C29N-SS C29N-SV (18-25) C29NR-SS C29NR-SV (13-20) imensions in Inches (mm) F 1 Clearance ole +.01 (+.25 mm) ody imensions and specifications may be changed without prior notice. s PG 7.49 (12.5).75 (19).20 (5).55 (14) PG 9.60 (15.2).83 (21).24 (6).67 (17) PG (18.5).87 (22).24 (6).87 (22) PG (20.3).94 (24).26 (6.5).87 (22) PG (22.3).91 (23).26 (6.5).94 (24) PG (28.4).94 (24).28 (7) 1.18 (30) PG (37.3) 1.14 (29).31 (8) 1.61 (41) PG (47) 1.38 (35).31 (8) 1.97 (50) 3/8 NPT.68 (17.2).83 (21).59 (15) 1/2 NPT.83 (21.1).94 (24).51 (13).67 (17) /.75 (19).87 (22) /.94 (24) 3/4 NPT 1.05 (26.7).98 (25).51 (13) 1.18 (30) 1 NPT 1.35 (34.3) 1.14 (29).75 (19) 1.57 (40) C12M-SS C12M-SV (3-6.5) C12MR-SS C12MR-SV (2-5) M12 x (12).75 (19).26 (6.5).55 (14) C16M-SS C16M-SV (5-10) C16MR-SS C16MR-SV (3-7) M16 x (16).87 (22).24 (6).87 (22) C20M-SS C20M-SV (10-14) C20MR-SS C20MR-SV (7-12) M20 x (20).91 (23).24 (6).94 (24) C25M-SS C25M-SV (13-18) C25MR-SS C25MR-SV (9-16) M25 x (25).94 (24).28 (7) 1.18 (30) C32M-SS C32M-SV (18-25) C32MR-SS C32MR-SV (13-20) M32 x (32) 1.14 (29).31 (8) 1.61 (41) C40M-SS C40M-SV (22-32) C40MR-SS C40MR-SV (20-26) M40 x (40) 1.38 (35).31 (8) 1.97 (50) Viton is a federally registered trademark of upont ow Elastomer. *Note: VE pproval only applies to Fittings with Metric. lso available: 316 INOX Stainless Steel The 316 material is much harder and ideal for direct exposure to salt water and chemical solutions in marine, off-shore, pharmaceutical, etc. This special Stainless Steel Strain Relief Fitting is produced upon request only. Please allow for longer delivery times. For inquiries - please call our Inside Technical Sales epartment ( or ). Stainless Steel (303), Nickel Plated rass & Nylon Locking Nuts and Other ccessories available on page 28. Stainless Steel Strain Relief Fittings can be used in many applications, where the environment dictates a corrosion proof solution. Typical applications include: Off-shore Marine Chemical Plants Food Processing Clean Room Other Rugged pplications F 1 Suggested Clearance ole for Non-ed Mounting lso available with the following approvals: STNR: as a una-n (NR) Insert PVF: as a Viton Insert 27 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

28 Nickel Plated rass Nylon Strain Relief ccessories for Strain Relief Fittings Summary Locking Nuts - Page 29 Locking Nuts are used when Cord Grips are installed into non-threaded holes. They are available in these materials: lack & Gray Nylon EMI/RFI Proof (Nickel Plated rass) Nickel Plated rass Zinc Plated Steel Stainless Steel (303) - INOX O-Rings & Seal Rings - Page 30 Provide the external seal between Installation and Strain Relief. O-Rings are available in: Seal Rings are available in: una-n Polyethylene Viton Fiber-Reinforced Plastic Silicone ole Plugs - Page 31/32 ome Plugs are designed to fit and seal European PG per IN FS/P / IN 46320/Ms & Metric threads. ccessories dapter,reducer,enlarger 28 ome Plugs available in: ex Plugs available in: lind Plugs availabe in: lack & Gray Nylon lack Nylon lack Nylon Nickel Plated rass Nickel Plated rass Stainless Steel Other ccessories - Page 32/33 Socket & Ratchet es: Various sizes available Cable Clamp: Nickel Plated rass dapters - Page 34/35 dapters will allow you to switch between PG, NPT & Metric threads to fit your application needs. lack Nylon: Nickel Plated rass: Metric to PG / PG to Metric s PG to NPT / Metric to NPT s PG to NPT / NPT to PG s NPT to PG / NPT to Metric s Metric to PG / PG to Metric s Reducers - Page Is your thread size off by one size? These Reducers will solve that threading problem. They convert holes which fit PG, NPT or Metric threads to a Smaller female thread of the same thread type. Gray Nylon: Nickel Plated rass: PG to PG s Metric to Metric s Metric to Metric s PG to PG s NPT to NPT s lack Nylon: Metric to Metric s Stainless Steel: Metric to Metric s PG to PG s Enlargers - Page 39 Is your thread size off by one size? These Enlargers will solve that threading problem. They convert holes which fit PG, NPT or Metric threads to a Larger female thread of the same thread type. lack Nylon: Nickel Plated rass: Metric to Metric s PG to PG s Metric to Metric s NPT to NPT s imensions and specifications may be changed without prior notice. Viton is a federally registered trademark of upont ow Elastomer.

29 lack & Gray Nylon Locking Nuts Part Numbers imensions in Inches (mm) lack Gray G Thickness s NP-07-K NP-07-GY PG 7.20 (5).75 (19) NP-09-K NP-09-GY PG 9.20 (5).87 (22) NP-11-K NP-11-GY PG (5).94 (24) NP-13-K NP-13-GY PG (6) 1.06 (27) NP-16-K NP-16-GY PG (6) 1.18 (30) NP-21-K NP-21-GY PG (7) 1.41 (36) NP-29-K NP-29-GY PG (7) 1.81 (46) NP-36-K NP-36-GY PG (8) 2.36 (60) NP-42-K NP-42-GY PG (8) 2.56 (65) NP-48-K NP-48-GY PG (8) 2.76 (70) NN-09-K NN-09-GY 3/8 NPT.28 (7).94 (24) NN-13-K NN-13-GY 1/2 NPT.24 (6) 1.06 (27) NN-21-K NN-21-GY 3/4 NPT.28 (7) 1.26 (32) NN-29-K NN-29-GY 1 NPT.28 (7) 1.57 (40) NM-12-K NM-12-GY M12 x (5).67 (17) NM-16-K NM-16-GY M16 x (5).87 (22) NM-20-K NM-20-GY M20 x (6) 1.06 (27) NM-25-K NM-25-GY M25 x (7) 1.42 (36) NM-32-K NM-32-GY M32 x (7) 1.61 (41) NM-40-K NM-40-GY M40 x (7) 1.97 (50) NM-50-K NM-50-GY M50 x (8) 2.36 (60) NM-63-K NM-63-GY M63 x (8) 2.95 (75) EMI/RFI - Nickel Plated rass Locking Nuts Part Numbers Nickel Plated rass w/ Cutting Edges ccessories for Strain Relief Fittings Locking Nuts - PG/NPT/Metric s imensions in Inches (mm) G Thickness s NP-07-E PG 7.11 (2.8).59 (15) NP-09-E PG 9.11 (2.8).71 (18) NP-11-E PG (3).83 (21) NP-13-E PG (3).91 (23) NP-16-E PG (3) 1.02 (26) NP-21-E PG (3.5) 1.26 (32) NP-29-E PG (4) 1.61 (41) NP-36-E PG (5) 2.01 (51) NP-42-E PG (5) 2.36 (60) NP-48-E PG (6) 2.52 (64) NN-13-E 1/2 NPT.13 (3).94 (24) NM-12-E M12 x (2.8).59 (15) NM-16-E M16 x (2.8).75 (19) NM-20-E M20 x (3).94 (24) NM-25-E M25 x (3.5) 1.18 (30) NM-32-E M32 x (5) 1.42 (36) NM-40-E M40 x (5) 1.81 (46) NM-50-E M50 x (5) 2.36 (60) NM-63-E M63 x (6) 2.76 (70) Note: E-Locknuts have the following approvals: CE & German Lloyd. Nylon & Nickel Plated rass Locknut () Zinc Plated Steel Locknut () EMI /RFI Proof Locknut () imensions and specifications may be changed without prior notice. G G Nickel Plated rass Locking Nuts Part Numbers Nickel Plated rass imensions in Inches (mm) G Thickness s NP-07-R PG 7.11 (2.8).59 (15) NP-09-R PG 9.11 (2.8).71 (18) NP-11-R PG (3).83 (21) NP-13-R PG (3).91 (23) NP-16-R PG (3) 1.02 (26) NP-21-R PG (3.5) 1.26 (32) NP-29-R PG (4) 1.61 (41) NP-36-R PG (5) 2.01 (51) NP-42-R PG (5) 2.36 (60) NP-48-R PG (5.5) 2.52 (64) NN-09-R 3/8 NPT.14 (3.5).75 (19) NN-13-R 1/2 NPT.12 (3).94 (24) NN-21-R 3/4 NPT.14 (3.5) 1.18 (30) NN-29-R 1 NPT.14 (3.5) 1.38 (35) NM-06-R M6 x (2.5).39 (10) NM-08-R M8 x (2.5).51 (13) NM-10-R M10 x (2.8).51 (13) NM-12-R M12 x (2.8).59 (15) NM-16-R M16 x (2.8).75 (19) NM-20-R M20 x (3).91 (23) NM-25-R M25 x (3.5) 1.14 (29) NM-32-R M32 x (4) 1.42 (36) NM-40-R M40 x (4.5) 1.77 (45) NM-50-R M50 x (5.5) 2.17 (55) NM-63-R M63 x (6) 2.76 (70) Zinc Plated Steel Locking Nuts Part Numbers imensions in Inches (mm) G Thickness s NN-10-ST 1 NPT.24 (6) 1.73 (44) NN-34-ST 1-1/4 NPT.20 (5) 2.01 (53) NN-36-ST 1-1/2 NPT.16 (4) 2.19 (55.5) Stainless Steel (303) Locking Nuts in PG & Metric threads are available upon request. See product infomation online. G 29 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

30 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 30 Polyethylene Part Numbers Fiber-reinforced Plastic ccessories for Strain Relief Fittings O-Rings & Seal Rings - PG/NPT/Metric s If NEM 4x or 6 (IP 68 or IP 69K - Submersible) is required, O-Rings or Seal Rings should be used when mounting Strain Relief Fittings to a control panel, secured with a Locking Nut. The straight Strain Relief Fittings feature a molded O-Ring groove. For these fittings the O-Ring is the best solution. The Snap Elbows and some of the Conduit Fittings don t have a recess for an O-Ring. In that case, the Seal Ring would be the better choice, unless the hole can be beveled to accommodate an O-Ring. Seal Rings These non-threaded Plugs are made of lack Nylon (RL 9005) and fit PG, NPT and Metric Strain Relief Fittings. L imensions in Inches (mm) C ole Outer O.. iameter SR-07-NY SR-07- PG 7.49 (12.5).65 (16.5).06 (1.5) SR-09-NY SR-09- PG 9.60 (15.2).75 (19).06 (1.5) SR-11-NY SR-11- PG (18.6).89 (22.5).06 (1.5) SR-13-NY SR-13- PG (20.4).98 (25).06 (1.5) SR-16-NY SR-16- PG (22.5) 1.06 (27).06 (1.5) SR-21-NY SR-21- PG (28.3) 1.32 (33.5).06 (1.5) SR-29-NY SR-29- PG (37) 1.71 (43.5).08 (2) SR-36-NY SR-36- PG (47) 2.17 (55).08 (2) SR-42-NY SR-42- PG (54) 2.48 (63).08 (2) SR-48-NY SR-48- PG (59.3) 2.72 (69).08 (2) SR-11-NY SR-11-3/8 NPT.73 (18.6).89 (22.5).06 (1.5) SR-13-NY SR-13-1/2 NPT.80 (20.4).98 (25).06 (1.5) SR-34-NY SR-21-3/4 NPT 1.06 (27) 1.43 (36).06 (1.5) SM-12-NY SM-12- M12 x (12).63 (16).08 (2) SM-16-NY SM-16- M16 x (16).79 (20).08 (2) SM-20-NY SM-20- M20 x (20).94 (24).08 (2) SM-25-NY SM-25- M25 x (25) 1.22 (31).08 (2) SM-32-NY SM-32- M32 x (32) 1.50 (38).08 (2) SM-40-NY SM-40- M40 x (40) 1.96 (48).08 (2) SM-50-NY SM-50- M50 x (50) 2.28 (58).08 (2) SM-63-NY SM-63- M63 x (63) 2.83 (72).08 (2) O-Ring Groove ccessories for Strain Relief Fittings lind Plugs - Nylon - fit PG/NPT/Metric s Part Numbers Fits PG Fits NPT Part Numbers Fits Metric imensions and specifications may be changed without prior notice. O-Rings O-Ring Groove imensions in Inches (mm) 1 2 L iameter (1) iameter (2) PL-07-K PG 7 - M12 x (6).18 (4.5).59 (15) 2 1 PL-09-K PG 9 3/8 NPT M16 x (7.5).22 (5.5).67 (17) PL-11-K PG 11 - M16 x (9.5).26 (6.5).75 (19) PL-13-K PG 13 1/2 NPT M20 x (11.5).33 (8.5).75 (19) PL-16-K PG 16 1/2 NPT M20 x (13.5).45 (11.5).77 (19.5) Inserts into PL-21-K PG 21 3/4 NPT M25 x (17.5).61 (15.5).93 (23.5) ome Nut for PL-29-K PG 29 1 & 1-1/4 NPT M32 x (24).75 (19) 1.02 (26) a liquid tight PL-36-K PG /2 NPT M40 x (31).98 (25) 1.10 (28) seal! PL-42-K PG 42 - M50 x (37) 1.18 (30) 1.10 (28) PL-48-K PG 48 - M63 x (43) 1.34 (34) 1.10 (28) C imensions in Inches (mm) una-n Viton Silicone E ole O.. OR-07-N OR-07-VT OR-07-SI PG 7.39 (10).06 (1.6) OR-09-N OR-09-VT OR-09-SI PG 9.47 (12).06 (1.6) OR-11-N OR-11-VT OR-11-SI PG (16).06 (1.6) OR-13-N OR-13-VT OR-13-SI PG (17).07 (1.8) OR-16-N OR-16-VT OR-16-SI PG (18).06 (1.6) OR-21-N OR-21-VT OR-21-SI PG (26).08 (2) OR-29-N OR-29-VT OR-29-SI PG (33).08 (2) OR-36-N OR-36-VT OR-36-SI PG (44).08 (2) OR-42-N OR-42-VT OR-42-SI PG (50).08 (2) OR-48-N OR-48-VT OR-48-SI PG (55).08 (2) OR-38-N OR-38-VT OR-38-SI 3/8 NPT.51 (13).08 (2) OR-18-N OR-18-VT OR-18-SI 1/2 NPT.75 (19).07 (1.8) OR-34-N OR-34-VT OR-34-SI 3/4 NPT.87 (22).08 (2) OR-10-N OR-10-VT OR-10-SI 1 NPT 1.14 (29).08 (2) OR-54-N OR-54-VT OR-54-SI 1-1/4 NPT 1.50 (38).10 (2.5) OR-64-N OR-64-VT OR-64-SI 1-1/2 NPT 1.77 (45).10 (2.5) OM-12-N OM-12-VT OM-12-SI M12 x (10).06 (1.6) OM-16-N OM-16-VT OM-16-SI M16 x (12).06 (1.6) OM-20-N OM-20-VT OM-20-SI M20 x (17).07 (1.8) OM-25-N OM-25-VT OM-25-SI M25 x (22).08 (2) OM-32-N OM-32-VT OM-32-SI M32 x (29).08 (2) OM-40-N OM-40-VT OM-40-SI M40 x (35).08 (2) OM-50-N OM-50-VT OM-50-SI M50 x (43).08 (2) OM-63-N OM-63-VT OM-63-SI M63 x (55).08 (2) Viton is a federally registered trademark of upont ow Elastomer. or E

31 Part Numbers ccessories for Strain Relief Fittings ole Plugs (ome & ex) - PG/NPT/Metric s ome Plugs - Nylon imensions in Inches (mm) lack Nylon Gray Nylon E Overall ome iameter P-07-K P-07-GY PG 7.31 (8).59 (15).20 (5) P-09-K P-09-GY PG 9.35 (9).75 (19).22 (5.5) P-11-K P-11-GY PG (9).87 (22).24 (6) P-13-K P-13-GY PG (9.5).98 (25).24 (6) P-16-K P-16-GY PG (9.5) 1.06 (27).24 (6) P-21-K P-21-GY PG (11) 1.30 (33) 31 (8) P-29-K P-29-GY PG (12) 1.73 (44).31 (8) P-36-K P-36-GY PG (15) 2.17 (55).39 (10) P-42-K P-42-GY PG (16) 2.44 (62).39 (10) P-48-K P-48-GY PG (16) 2.72 (69).47 (12) M-12-K M-12-GY M12 x (10).59 (15).24 (6) M-16-K M-16-GY M16 x (11.5).79 (20).28 (7) M-20-K M-20-GY M20 x (9.5).98 (25).24 (6) M-25-K M-25-GY M25 x (15.5) 1.18 (30).43 (11) M-32-K M-32-GY M32 x (16) 1.50 (38).43 (11) M-40-K M-40-GY M40 x (18) 1.81 (46).51 (13) M-50-K M-50-GY M50 x (18.5) 2.20 (56).51 (13) M-63-K M-63-GY M63 x (19) 2.72 (69).59 (15) Part Numbers ex Plugs - Nylon imensions in Inches (mm) lack Nylon X E Overall P-07-K PG 7 / 1/4 NPT.51 (13).59 (15).33 (8.5) P-09-K PG 9.51 (13).75 (19).33 (8.5) P-11-K PG (14.5).94 (24).35 (9) P-13-K PG (14.5).94 (24).35 (9) P-16-K PG (16) 1.10 (28).41 (10.5) P-21-K PG (17.5) 1.42 (36).45 (11.5) P-29-K PG (18) 1.81 (46).45 (11.5) P-36-K PG (20) 2.17 (55).53 (13.5) P-42-K PG (20) 2.36 (60).53 (13.5) P-48-K PG (21) 2.76 (70).57 (14.5) N-38-K 3/8 NPT.83 (21).75 (19).59 (15) N-12-K 1/2 NPT.81 (20.5).94 (24).55 (14) N-34-K 3/4 NPT.87 (22) 1.10 (28).63 (16) N-10-K 1 NPT.91 (23) 1.34 (34).67 (17) E Nylon & Nickel Plated rass ex Plug imensions and specifications may be changed without prior notice. Nylon ex Plug ome Plugs - Nickel Plated rass Part Numbers Nickel Plated rass imensions in Inches (mm) E Overall ome iameter P-07-R PG 7.31 (8).55 (14).20 (5) P-09-R PG 9.35 (9).67 (17).24 (6) P-11-R PG (9).79 (20).24 (6) P-13-R PG (9.5).87 (22).26 (6.5) P-16-R PG (9.5).94 (24).26 (6.5) P-21-R PG (11) 1.18 (30).28 (7) P-29-R PG (12) 1.54 (39).31 (8) P-36-R PG (15) 1.97 (50).35 (9) P-42-R PG (16) 2.24 (57).39 (10) P-48-R PG (16) 2.52 (64).39 (10) M-12-R M12 x (10).55 (14).37 (9.5) M-16-R M16 x (11.5).71 (18).20 (5) M-20-R M20 x (9.5).87 (22).26 (6.5) M-25-R M25 x (15.5) 1.10 (28).28 (7) M-32-R M32 x (16) 1.38 (35).31 (8) M-40-R M40 x (18) 1.73 (44).33 (8.5) M-50-R M50 x (18.5) 2.13 (54).35 (9) M-63-R M63 x (19) 2.64 (67).39 (10) ex Plugs - Nickel Plated rass Part Numbers Nickel Plated rass M-12-K M12 x (13).59 (15).33 (8.5) M-16-K M16 x (13).75 (19).33 (8.5) M-20-K M20 x (14.5).94 (24).35 (9) M-25-K M25 x (16) 1.10 (28).41 (10.5) M-32-K M32 x (17.5) 1.42 (36).45 (11.5) M-40-K M40 x (18) 1.81 (46).45 (11.5) X Nickel Plated rass M-50-K M50 x (20) 2.17 (55).53 (13.5) ex Plug M-63-K M63 x (21) 2.76 (70).57 (14.5) For all ole Plugs listed, the O-Ring is optional (see page 30) To order plug with O-Ring, add - (una-n) or -V (Viton ) to part number (e.g. P-11-R-, P-11-R-V) Viton is a federally registered trademark of upont ow Elastomer. X E Note: P & M Plugs can be tightened with ex & llen wrenches, as well as regular screwdrivers. See page 49 for thread imensions in Inches (mm) X E Overall See page 49 for thread P-07-R PG 7 / 1/4 NPT.31 (8).55 (14).20 (5) P-09-R PG 9.35 (9).67 (17).24 (6) P-11-R PG (9.5).79 (20).24 (6) P-13-R PG (10).87 (22).26 (6.5) P-16-R PG (10).94 (24).26 (6.5) P-21-R PG (10.5) 1.18 (30).28 (7) P-29-R PG (12.5) 1.61 (41).31 (8) P-36-R PG (13) 1.97 (50).31 (8) P-42-R PG (15) 2.28 (58).35 (9) P-48-R PG (16.5) 2.56 (65).39 (10) M-12-R M12 x (9.5).55 (14).26 (6.5) M-16-R M16 x (9).75 (19).24 (6) M-20-R M20 x (9.5).87 (22).24 (6) M-25-R M25 x (10.5) 1.18 (30).28 (7) M-32-R M32 x (12.5) 1.61 (41).31 (8) M-40-R M40 x (13) 1.81 (46).31 (8) M-50-R M50 x (15) 2.17 (55).35 (9) M-63-R M63 x (16.5) 2.76 (70).39 (10) E 31 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

32 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger This clamp offers extra pull-out resistance. Made of durable Nickel Plated rass, it offers an excellent solution for your specific application needs. ccessories for Strain Relief Fittings ex Plugs - Stainless Steel - PG/NPT/Metric s These Plugs are designed to fit and seal European PG per IN FS/P and IN 46320/Ms and Metric threads. They are made of Stainless Steel and are available with una-n, Viton or Silicone O-Ring. lso available in Nylon or Nickel Plated rass. (See page 31) Part Numbers imensions in Inches (mm) w/ una-n O-Ring w/ Viton O-Ring w/ Silicone O-Ring X E ccessories for Strain Relief Fittings Clamp - fit PG/NPT & Male Metric s F KL12M-R (5-7.5) M12 x (12).59 (15).22 (5.5).63 (16) KL16M-R (7-10) M16 x (16).63 (16).24 (6).75 (19) KL20M-R (10-14) M20 x (20).71 (18).26 (6.5).94 (24) T KL25M-R ( ) M25 x (25).83 (21).31 (8) 1.34 (34) KL32M-R (16-27) M32 x (32).87 (22).31 (8) 1.65 (42) KL40M-R (22-33) M40 x (40) 1.00 (25.5).37 (9.5) 2.05 (52) KL50M-R ( ) M50 x (50) 1.00 (25.5).37 (9.5) 2.05 (52) 32 imensions and specifications may be changed without prior notice. Overall P-07-SS- P-07-SS-V P-07-SS-S PG 7 / 1/4 NPT.31 (8).55 (14).20 (5) P-09-SS- P-09-SS-V P-09-SS-S PG 9.35 (9).67 (17).24 (6) P-11-SS- P-11-SS-V P-11-SS-S PG (9.5).79 (20).24 (6) P-13-SS- P-13-SS-V P-13-SS-S PG (10).87 (22).26 (6.5) P-16-SS- P-16-SS-V P-16-SS-S PG (10).94 (24).26 (6.5) P-21-SS- P-21-SS-V P-21-SS-S PG (10.5) 1.18 (30).28 (7) P-29-SS- P-29-SS-V P-29-SS-S PG (12.5) 1.61 (41).31 (8) P-36-SS- P-36-SS-V P-36-SS-S PG (13) 1.97 (50).31 (8) P-42-SS- P-42-SS-V P-42-SS-S PG (15) 2.28 (58).35 (9) P-48-SS- P-48-SS-V P-48-SS-S PG (16.5) 2.56 (65).39 (10) M-12-SS- M-12-SS-V M-12-SS-S M12 x (9.5).55 (14).26 (6.5) M-16-SS- M-16-SS-V M-16-SS-S M16 x (9).75 (19).24 (6) M-20-SS- M-20-SS-V M-20-SS-S M20 x (9.5).87 (22).24 (6) M-25-SS- M-25-SS-V M-25-SS-S M25 x (10.5) 1.18 (30).28 (7) M-32-SS- M-32-SS-V M-32-SS-S M32 x (12.5) 1.61 (41).31 (8) M-40-SS- M-40-SS-V M-40-SS-S M40 x (13) 1.81 (46).31 (8) M-50-SS- M-50-SS-V M-50-SS-S M50 x (15) 2.17 (55).35 (9) M-63-SS- M-63-SS-V M-63-SS-S M63 x (21) 2.76 (70).39 (10) Part Numbers Cable imensions in Inches (mm) Nickel Plated rass Range (Male) T F ole O.. ody KL07-R (5.5-8) PG 7.49 (12.5).58 (14.8).22 (5.5).63 (16) KL09-R (6.5-10) PG 9.60 (15.2).65 (16.6).24 (6).75 (19) KL11-R (7.5-12) PG (18.5).68 (17.3).24 (6).87 (22) KL13-R (8.5-14) PG (20.3).70 (17.8).26 (6.5).94 (24) KL16-R (9.5-16) PG (22.3).72 (18.3).26 (6.5) 1.02 (26) KL21-R (12-21) PG (28.4).82 (20.8).30 (7.5) 1.30 (33) KL29-R (19-30) PG (37.3).86 (21.8).31 (8) 1.65 (42) KL36-R (25-37) PG (47) 1.00 (25.3).37 (9.5) 2.05 (52) KL42-R (31-43) PG (54.1) 1.04 (26.3).39 (10) 2.32 (59) KL48-R (35-48) PG (59.4) 1.07 (27.3).43 (11) 2.32 (59) E Viton is a federally registered trademark of upont ow Elastomer. X

33 Socket ccessories for Strain Relief Fittings Socket & Ratchet es Part Numbers Used with Sizes imensions in Inches (mm) Sockets for Ratchet Plastic ome Nut Metal ome Nut imensions and specifications may be changed without prior notice. (pplies to Socket only) F L C Inner iameter Outer iameter S-1400-WR R-1400-WR* PG7, M12.55 (14) 2.36 (60).35 (9).75 (19) S-1500-WR R-1500-WR* PG7, M12.59 (15) 2.36 (60).37 (9.5).79 (20) S-1700-WR R-1700-WR* PG 9, 3/8 NPT, M16.67 (17) 2.36 (60).39 (10).93 (23.5) S-1900-WR R-1900-WR* PG 9, 3/8 NPT, M16 3/8 NPT, M16.75 (19) 2.36 (60).43 (11) 1.02 (26) S-2000-WR R-2000-WR* PG 11, M16-E.79 (20) 2.36 (60).47 (12) 1.06 (27) S-2200-WR R-2200-WR* PG 11, 3/8 NPT, M16-E PG 13, 1/2 NPT, M20.87 (22) 2.36 (60).51 (13) 1.16 (29.5) S-2400-WR R-2400-WR* PG 13, 1/2 NPT, M20 PG 16, 1/2 NPT, M20-E.94 (24) 2.36 (60).59 (15) 1.28 (32.5) S-2700-WR R-2700-WR* PG 13, 1/2 NPT-E, M20-E 1.06 (27) 2.36 (60).67 (17) 1.40 (35.5) S-3000-WR R-3000-WR* PG 21, 3/4 NPT, M (30) 2.36 (60).71 (18) 1.59 (40.5) S-3300-WR - PG 21, 3/4 NPT, M (33) 2.36 (60).79 (20) 1.71 (43.5) S-3600-WR (36) 2.36 (60).87 (22) 1.87 (47.5) S-4000-WR - PG 29, 1 NPT, M (40) 3.94 (100).98 (25) 2.07 (52.5) S-4100-WR (41) 3.94 (100) 1.06 (27) 2.11 (53.5) S-4200-WR - PG 29, 1, 1-1/4 NPT, M (42) 3.94 (100) 1.06 (27) 2.15 (54.5) S-4600-WR - 1-1/4 NPT 1.81 (46) 3.94 (100) 1.22 (31) 2.36 (60) S-5000-WR - PG 36, M (50) 3.94 (100) 1.26 (32) 2.58 (65.5) S-5300-WR - PG 36, 1-1/2 NPT, M (53) 3.94 (100) 1.26 (32) 2.82 (71.5) S-5500-WR (55) 3.94 (100) 1.26 (32) 2.83 (72) S-5700-WR - PG 42, M (57) 3.94 (100) 1.42 (36) 2.97 (75.5) S-6000-WR - PG 42, M (60) 3.94 (100) 1.50 (38) 3.09 (78.5) S-6400-WR - PG 48, M (64) 3.94 (100) 1.57 (40) 3.31 (84) S-6500-WR - PG 48, M (65) 3.94 (100) 1.65 (42) 3.35 (85) S-6800-WR - M63 M (68) 3.94 (100) 1.65 (42) 3.43 (87) andle The handy, light weight eep Socket is manufactured from alloy steel. It is slit open along the full length to accommodate the installed cable during tightening of the dome nut. The wrench encloses the dome nut on five sides, giving the nut additional rigidity during tightening. This is especially important if a stiff cable is used. oes not work with all Flex Fittings. The Ratchet consists of three components: ead, andle & Socket. It provides a quick & easy method of tightening cord grips. Only one andle & Ratchet ead is required. Sockets are interchangeable. Interchangeable Sockets in various sizes available. Ratchet ead with one-sided opening for easy access. * Note: When Ordering the Ratchet, please make sure to order all 3 components together: R Ratchet ead R andle R-xxxx-WR - Socket (see table above) L F C 33 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

34 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 34 ealing with foreign products? Is connecting a challenge? Well, look no further! Nickel Plated dapters, rass Liquid Reducers Tight & Strain Enlargers Relief Fittings dapters - Nickel Plated rass dapters - NPT to PG s Part Numbers s imensions in Inches (mm) Male Female W T Nickel Plated rass w/ una-n O-Ring imensions and specifications may be changed without prior notice. dapters - PG to NPT s Part Numbers s imensions in Inches (mm) luminum Male Female W T G-0912-R G-0912-L PG 9 1/2 NPT.94 (24).24 (6).94 (24) G-1112-R - PG 11 1/2 NPT.94 (24).24 (6).89 (22.7) G-1312-R - PG 13 1/2 NPT.94 (24).26 (6.5).93 (23.5) G-1612-R - PG 16 1/2 NPT.94 (24).26 (6.5).91 (23) G-2112-R - PG 21 1/2 NPT 1.18 (30).28 (7).59 (15) G-2134-R - PG 21 3/4 NPT 1.18 (30).28 (7).94 (24) G-2910-R - PG 29 1 NPT 1.57 (40).31 (8).79 (20) N-1407-R 1/4 NPT PG 7.75 (19).59 (15).98 (25) N-1209-R 1/2 NPT PG 9.98 (25).79 (20) 1.18 (30) N-1211-R 1/2 NPT PG (25).79 (20) 1.18 (30) N-1213-R 1/2 NPT PG (25).79 (20) 1.18 (30) N-1221-R 1/2 NPT PG (33).79 (20) 1.26 (32) N-3421-R 3/4 NPT PG (33).67 (17) 1.22 (31) N-1029-R 1 NPT PG (41).98 (25) 1.38 (35) N-5429-R 1-1/4 NPT PG (43).94 (24) 1.34 (34) dapters - NPT to Metric s Part Numbers s imensions in Inches (mm) Male Female W T T-1216-R 1/2 NPT M16 x (25).79 (20) 1.18 (30) T-1220-R 1/2 NPT M20 x (25).79 (20) 1.18 (30) T-1225-R 1/2 NPT M25 x (32).79 (20) 1.18 (30) T-3425-R 3/4 NPT M25 x (31.6).75 (19) 1.18 (30) T-1032-R 1 NPT M32 x (38).98 (25) 1.61 (41) T-5432-R 1-1/4 NPT M32 x (42.5).59 (15) 1.30 (33) X (F-xxxx-R, P-xxxx-R & G-xxxx-L) (N-xxxx-R) T W (G-xxxx-R & M-xxxx-R) T T W More custom parts available online at or upon request! (T-xxxx-R) W T dapters - PG to Metric s Part Numbers s imensions in Inches (mm) Male dapters - Metric to PG s Part Numbers s imensions in Inches (mm) Male Female Female X T Outer iameter X T Outer iameter P-0916-R PG 9 M16 x (20).24 (6).65 (16.5) P-1120-R PG 11 M20 x (22).26 (6.5).75 (19) P-1320-R PG 13 M20 x (22).26 (6.5).75 (19) P-1625-R PG 16 M25 x (27).26 (6.5).83 (21) F-1609-R M16 x 1.5 PG 9.79 (20).24 (6).65 (16.5) F-2011-R M20 x 1.5 PG (22).26 (6.5).75 (19) F-2013-R M20 x 1.5 PG (22).26 (6.5).75 (19) F-2016-R M20 x 1.5 PG (24).26 (6.5).75 (19) F-2516-R M25 x 1.5 PG (28).26 (6.5).75 (19) F-2521-R M25 x 1.5 PG (30).26 (6.5).83 (21) F-3229-R M32 x 1.5 PG (39).28 (7).91 (23) dapters - Metric to NPT s Part Numbers s imensions in Inches (mm) Nickel Plated rass w/ una-n O-Ring Male Female W T M-1612-R M16 x 1.5 1/2 NPT.94 (24).24 (6).91 (23) M-2012-R M20 x 1.5 1/2 NPT.94 (24).24 (6).91 (23) M-2512-R M25 x 1.5 1/2 NPT 1.18 (30).28 (7).59 (15) M-2534-R M25 x 1.5 3/4 NPT 1.18 (30).28 (7) 1.07 (26) M-3210-R M32 x NPT 1.57 (40).31 (8) 1.30 (33) M-3254-R M32 x /4 NPT 1.81 (46).31 (8) 1.30 (33) specifications.

35 T T C T E W T W T W Nickel Plated dapters, rass Liquid Reducers Tight & Strain Enlargers Relief Fittings dapters - lack Nylon W dapters - Metric to PG s Part Numbers s dapter Male Female dapters - PG to NPT s Part Numbers s dapter Male Female dapters - Metric to NPT s Part Numbers s dapter Male Female imensions and specifications may be changed without prior notice. imensions in Inches (mm) T W imensions in Inches (mm) T W imensions in Inches (mm) T W Inner iameter M-1612-K M16 x 1.5 1/2 NPT E.28 (7) 1.10 (28) N/ 1.02 (26) M-2012-K M20 x 1.5 1/2 NPT E.28 (7) 1.06 (27) N/ 1.02 (26) Inner iameter Inner iameter F-1207-K M12 x 1.5 PG 7.31 (8).79 (20).26 (6.5).67 (17) F-1609-K M16 x 1.5 PG 9 C.59 (15) 1.34 (34).33 (8.5) N/ F-2013-K M20 x 1.5 PG (8).83 (21).55 (14).98 (25) F-2513-K M25 x 1.5 PG13.31 (8).55 (14).71 (18) 1.14 (29) F-2516-K M25 x 1.5 PG (8).87 (22).71 (18) 1.14 (29) F-3221-K M32 x 1.5 PG (10).98 (25).98 (25) 1.43 (36) F-4029-K M40 x 1.5 PG (10).98 (25) 1.30 (33) 1.77 (45) F-5036-K M50 x 1.5 PG (12) 1.14 (29) 1.69 (43) 2.17 (55) F-6342-K M63 x 1.5 PG 42 C.59 (15).79 (20) 2.05 (52) N/ F-6348-K M63 x 1.5 PG 48 C.59 (15) 1.38 (35) 2.01 (51) N/ dapters - PG to Metric s Part Numbers s dapter Male Female imensions in Inches (mm) T W Inner iameter P-0712-K PG 7 M12 x 1.5 C.59 (15) 1.34 (34).24 (6) N/ P-0912-K PG 9 M12 x 1.5 C.59 (15) 1.34 (34).33 (8.5) N/ P-0916-K PG 9 M16 x (8).79 (20).35 (9).83 (21) P-1116-K PG 11 M16 x 1.5 C.59 (15) 1.34 (34).45 (11.5) N/ P-1120-K PG 11 M20 x 1.5 C.59 (15) 1.34 (34).45 (11.5) N/ P-1316-K PG 13 M16 x (8).55 (14).55 (14).98 (25) P-1320-K PG 13 M20 x (8).83 (21).55 (14).98 (25) P-1620-K PG 16 M20 x (8).83 (21).63 (16) 1.06 (27) P-1625-K PG 16 M25 x (8).91 (23).63 (16) 1.18 (30) P-2125-K PG 21 M25 x 1.5 C.59 (15) 1.34 (34).81 (20.5) N/ P-2132-K PG 21 M32 x (8).91 (23).83 (21) 1.46 (37) P-2932-K PG 29 M32 x 1.5 C.59 (15) 1.34 (34) 1.10 (28) N/ P-2940-K PG 29 M40 x (10) 1.06 (27) 1.18 (30) 1.77 (45) P-3640-K PG 36 M40 x 1.5 C.59 (15).79 (20) 1.50 (38) N/ P-3650-K PG 36 M50 x 1.5 C.59 (15) 1.36 (34.5) 1.46 (37) N/ P-4240-K PG 42 M40 x 1.5 C.59 (15).79 (20) 1.50 (38) N/ P-4250-K PG 42 M50 x 1.5 C.59 (15) 1.36 (34.5) 1.69 (43) N/ P-4850-K PG 48 M50 x 1.5 C.59 (15).79 (20) 1.50 (38) N/ P-4863-K PG 48 M63 x 1.5 C.59 (15) 1.38 (35) 1.89 (48) N/ G-1112-K PG 13 1/2 NPT.28 (7).83 (21) N/.94 (24) G-1312-K PG 11 1/2 NPT.35 (9).91 (23) N/.94 (24) specifications. 35 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

36 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 36 Is your thread size off by one size? These Reducers will solve that threading problem. They convert holes which fit PG, NPT or Metric threads to a smaller female thread of the same thread type. Reducers - Metric to Metric s Part Numbers s imensions in Inches (mm) Male Female Nickel Plated dapters, rass Liquid Reducers Tight & Strain Enlargers Relief Fittings Reducers (ex & Round) - Nickel Plated rass T Outer iameter RR-1612-R M16 x 1.5 M12 x (18).24 (6).33 (8.5) RR-2012-R M20 x 1.5 M12 x (24).26 (6.5).35 (9) RR-2016-R M20 x 1.5 M16 x (24).26 (6.5).35 (9) RR-2516-R M25 x 1.5 M16 x (30).28 (7).39 (10) RR-2520-R M25 x 1.5 M20 x (30).28 (7).39 (10) RR-3220-R M32 x 1.5 M20 x (39).31 (8).45 (11.5) RR-3225-R M32 x 1.5 M25 x (39).31 (8).45 (11.5) RR-4025-R M40 x 1.5 M25 x (43).31 (8).45 (11.5) RR-4032-R M40 x 1.5 M32 x (43).35 (9).49 (12.5) RR-5032-R M50 x 1.5 M32 x (57).39 (10).55 (14) RR-5040-R M50 x 1.5 M40 x (57).39 (10).55 (14) RR-6340-R M63 x 1.5 M40 x (64).39 (10).55 (14) RR-6350-R M63 x 1.5 M50 x (64).39 (10).55 (14) Reducers - PG to PG s Part Numbers s imensions in Inches (mm) Male Female T Outer iameter RR-0907-R PG 9 PG 7.67 (17).24 (6).33 (8.5) RR-1107-R PG 11 PG 7.79 (20).24 (6).33 (8.5) RR-1109-R PG 11 PG 9.79 (20).24 (6).33 (8.5) RR-1309-R PG 13 PG 9.87 (22).26 (6.5).35 (9) RR-1311-R PG 13 PG (22).26 (6.5).35 (9) RR-1609-R PG 16 PG 9.94 (24).26 (6.5).37 (9.5) RR-1611-R PG 16 PG (24).26 (6.5).37 (9.5) RR-1613-R PG 16 PG (24).26 (6.5).37 (9.5) RR-2111-R PG 21 PG (30).28 (7).39 (10) RR-2113-R PG 21 PG (30).28 (7).39 (10) RR-2116-R PG 21 PG (30).28 (7).39 (10) RR-2916-R PG 29 PG (39).31 (8).45 (11.5) RR-2921-R PG 29 PG (39).31 (8).45 (11.5) RR-3621-R PG 36 PG (50).35 (9).49 (12.5) RR-3629-R PG 36 PG (50).35 (9).49 (12.5) RR-4229-R PG 42 PG (57).39 (10).55 (14) RR-4236-R PG 42 PG (57).39 (10).55 (14) RR-4836-R PG 48 PG (64).39 (10).55 (14) RR-4842-R PG 48 PG (64).39 (10).55 (14) (RR-xxxx-R) T W (RQ-xxxx-R, RP-xxxx-R & RM-xxxx-R) T imensions and specifications may be changed without prior notice. Reducers - PG to PG s Part Numbers s imensions in Inches (mm) w/ una-n O-Ring without O-Ring Male Reducers - Metric to Metric s Part Numbers s imensions in Inches (mm) w/ una-n O-Ring Male Reducers - NPT to NPT s Part Numbers s imensions in Inches (mm) Male Female Female Female W T W T W T RQ-0907-R RP-0907-R PG 9 PG 7.67 (17).24 (6).34 (8.8) RQ-1107-R RP-1107-R PG 11 PG 7.79 (20).24 (6).35 (9) RQ-1109-R RP-1109-R PG 11 PG 9.79 (20).24 (6).35 (9) RQ-1309-R RP-1309-R PG 13 PG 9.87 (22).26 (6.5).37 (9.5) RQ-1311-R RP-1311-R PG 13 PG (22).26 (6.5).37 (9.5) RQ-1609-R RP-1609-R PG 16 PG 9.94 (24).26 (6.5).37 (9.5) RQ-1611-R RP-1611-R PG 16 PG (24).26 (6.5).37 (9.5) RQ-1613-R RP-1613-R PG 16 PG (24).26 (6.5).37 (9.5) RQ-2111-R RP-2111-R PG 21 PG (30).28 (7).41 (10.3) RQ-2113-R RP-2113-R PG 21 PG (30).28 (7).41 (10.3) RQ-2116-R RP-2116-R PG 21 PG (30).28 (7).41 (10.3) RQ-2916-R RP-2916-R PG 29 PG (40).31 (8).45 (11.5) RQ-2921-R RP-2921-R PG 29 PG (40).31 (8).45 (11.5) RQ-3621-R RP-3621-R PG 36 PG (50).35 (9).49 (12.5) RQ-3629-R RP-3629-R PG 36 PG (50).35 (9).49 (12.5) RQ-4229-R RP-4229-R PG 42 PG (57).39 (10).53 (13.5) RQ-4236-R RP-4236-R PG 42 PG (57).39 (10).53 (13.5) RQ-4836-R RP-4836-R PG 48 PG (64).39 (10).53 (13.5) RQ-4842-R RP-4842-R PG 48 PG (64).39 (10).53 (13.5) W (RN-xxxx-R) T RM-1612-R M16 x 1.5 M12 x (17).20 (5).31 (8) RM-2012-R M20 x 1.5 M12 x (22).24 (6).35 (9) RM-2016-R M20 x 1.5 M16 x (22).24 (6).35 (9) RM-2516-R M25 x 1.5 M16 x (27).28 (7).39 (10) RM-2520-R M25 x 1.5 M20 x (27).28 (7).39 (10) RM-3216-R M32 x 1.5 M16 x (34).31 (8).34 (11) RM-3220-R M32 x 1.5 M20 x (34).31 (8).43 (11) RM-3225-R M32 x 1.5 M25 x (34).31 (8).43 (11) RM-4020-R M40 x 1.5 M20 x (43).31 (8).47 (12) RM-4025-R M40 x 1.5 M25 x (43).31 (8).47 (12) RM-4032-R M40 x 1.5 M32 x (43).31 (8).47 (12) RM-5025-R M50 x 1.5 M25 x (55).35 (9).51 (13) RM-5032-R M50 x 1.5 M32 x (55).35 (9).51 (13) RM-5040-R M50 x 1.5 M40 x (55).35 (9).51 (13) RM-6332-R M63 x 1.5 M32 x (65).39 (10).55 (14) RM-6340-R M63 x 1.5 M40 x (65).39 (10).55 (14) RM-6350-R M63 x 1.5 M50 x (65).39 (10).55 (14) RN-3412-R 3/4 NPT 1/2 NPT 1.18 (30).71 (18).87 (22) RN-1034-R 1 NPT 3/4 NPT 1.30 (33).98 (25) 1.14 (29) RN-5410-R 1-1/4 NPT 1 NPT 1.69 (43).98 (25) 1.14 (29) specifications.

37 Nickel Plated dapters, rass Liquid Reducers Tight & Strain Enlargers Relief Fittings Reducers - lack & Gray Nylon Reducers - Metric to Metric s Part Numbers s dapter Male Female imensions in Inches (mm) T W Outer iameter imensions and specifications may be changed without prior notice. RR-1612-GY M16 x 1.5 M12 x (9) 1.06 (27).87 (22).79 (20) RR-2016-GY M20 x 1.5 M16 x (9) 1.06 (27) 1.06 (27).94 (24) RR-2520-GY M25 x 1.5 M20 x (10).67 (17) 1.26 (32) 1.14 (29) RR-3225-GY M32 x 1.5 M25 x (12).75 (19) 1.57 (40) 1.42 (36) RR-4032-GY M40 x 1.5 M32 x (12).75 (19) 2.01 (51) 1.81 (46) RR-5040-GY M50 x 1.5 M40 x (14).83 (21) 2.40 (61) 2.17 (55) RR-6350-GY M63 x 1.5 M50 x (15).87 (22) 2.95 (75) 2.68 (68) T C T W Reducers - PG to PG s Part Numbers s dapter Male Female Reducers - Metric to Metric s Part Numbers s dapter Male Female imensions in Inches (mm) T W Inner iameter RM-1612-K M16 x 1.5 M12 x 1.5 C.31 (8).55 (14).39 (10).79 (20) RM-2016-K M20 x 1.5 M16 x 1.5 C.31 (8).55 (14).53 (13.5).98 (25) RM-2520-K M25 x 1.5 M20 x 1.5 C.31 (8).55 (14).71 (18) 1.14 (29) RM-3225-K M32 x 1.5 M25 x 1.5 C.39 (10).63 (16).91 (23) 1.42 (36) RM-4032-K M40 x 1.5 M32 x (15).79 (20) 1.18 (30) N/ RM-5040-K M50 x 1.5 M40 x (15).79 (20) 1.50 (38) N/ RM-6350-K M63 x 1.5 M50 x (15).79 (20) 1.89 (48) N/ imensions in Inches (mm) T W Outer iameter RR-0907-GY PG 9 PG 7.31 (8).55 (14).75 (19) N/ RR-1109-GY PG 11 PG 9.31 (8).71 (18).89 (22.5) N/ RR-1309-GY PG 13 PG 9.31 (8).47 (12) 1.06 (27) N/ RR-1311-GY PG 13 PG (9).83 (21) 1.0 (25.5) N/ RR-1609-GY PG 16 PG 9.39 (10).51 (13) 1.14 (29) N/ RR-1611-GY PG 16 PG (10).51 (13) 1.14 (29) N/ RR-1613-GY PG 16 PG (10).98 (25) 1.13 (28.5) N/ RR-2113-GY PG 21 PG (11).53 (13.5) 1.42 (36) N/ RR-2116-GY PG 21 PG (11).53 (13.5) 1.42 (36) N/ RR-2921-GY PG 29 PG (11).53 (13.5) 1.81 (46) N/ RR-3629-GY PG 36 PG (11).59 (15) 2.28 (58) N/ specifications. Reducers - NPT to NPT s Part Numbers s dapter Male Female imensions in Inches (mm) T Inner iameter R /4 NPT 1/2 NPT C.637 (16.2).887 (22.5).696 (17.7) R /4 NPT 3/8 NPT C.625 (15.9).875 (22.2).696 (17.7) R NPT 1/2 NPT C.65 (16.5).90 (22.9).91 (23.1) R NPT 3/4 NPT C.65 (16.5).90 (22.9).92 (23.4) R /2 NPT 1/4 NPT C.566 (14.4).816 (20.7).56 (14.2) R /2 NPT 3/8 NPT C.574 (14.6).824 (20.9).561 (14.2) W T T 37 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

38 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 38 without O-Ring Nickel Plated dapters, rass Liquid Reducers Tight & Strain Enlargers Relief Fittings Reducers - Stainless Steel Reducers - Metric to Metric s Part Numbers s imensions in Inches (mm) with una-n O-Ring Male Female W T RM-1612-SS RM-1612-SS- M16 x 1.5 M12 x (17).20 (5).35 (9) RM-2012-SS RM-2012-SS- M20 x 1.5 M12 x (22).24 (6).37 (9.5) RM-2016-SS RM-2016-SS- M20 x 1.5 M16 x (22).24 (6).37 (9.5) RM-2516-SS RM-2516-SS- M25 x 1.5 M16 x (27).28 (7).41 (10.5) RM-2520-SS RM-2520-SS- M25 x 1.5 M20 x (27).28 (7).41 (10.5) RM-3216-SS RM-3216-SS- M32 x 1.5 M16 x (34).31 (8).49 (12.5) RM-3220-SS RM-3220-SS- M32 x 1.5 M20 x (34).31 (8).49 (12.5) RM-3225-SS RM-3225-SS- M32 x 1.5 M25 x (34).31 (8).49 (12.5) RM-4020-SS RM-4020-SS- M40 x 1.5 M20 x (43).31 (8).51 (13) RM-4025-SS RM-4025-SS- M40 x 1.5 M25 x (43).31 (8).51 (13) RM-4032-SS RM-4032-SS- M40 x 1.5 M32 x (43).31 (8).51 (13) RM-5025-SS RM-5025-SS- M50 x 1.5 M25 x (55).35 (9).59 (15) RM-5032-SS RM-5032-SS- M50 x 1.5 M32 x (55).35 (9).59 (15) RM-5040-SS RM-5040-SS- M50 x 1.5 M40 x (55).35 (9).59 (15) RM-6332-SS RM-6332-SS- M63 x 1.5 M32 x (65).39 (10).65 (16.5) RM-6340-SS RM-6340-SS- M63 x 1.5 M40 x (65).39 (10).65 (16.5) RM-6350-SS RM-6350-SS- M63 x 1.5 M50 x (65).39 (10).65 (16.5) dapter, Reducer & Enlarger pplications: without O-Ring International machine builder & equipment Import / Export oriented projects dapting to domestic markets Reducers - PG to PG s Part Numbers s imensions in Inches (mm) with una-n O-Ring Male Female W T RP-0907-SS RQ-0907-SS PG 9 PG 7.67 (17).24 (6).34 (8.8) RP-1107-SS RQ-1107-SS PG 11 PG 7.87 (22).24 (6).35 (9) RP-1109-SS RQ-1109-SS PG 11 PG 9.87 (22).24 (6).35 (9) RP-1309-SS RQ-1309-SS PG 13 PG 9.87 (22).26 (6.5).37 (9.5) RP-1311-SS RQ-1311-SS PG 13 PG (22).26 (6.5).37 (9.5) RP-1609-SS RQ-1609-SS PG 16 PG 9.94 (24).26 (6.5).37 (9.5) RP-1611-SS RQ-1611-SS PG 16 PG (24).26 (6.5).37 (9.5) RP-1613-SS RQ-1613-SS PG 16 PG (24).26 (6.5).37 (9.5) RP-2111-SS RQ-2111-SS PG 21 PG (30).28 (7).41 (10.3) RP-2113-SS RQ-2113-SS PG 21 PG (30).28 (7).41 (10.3) RP-2116-SS RQ-2116-SS PG 21 PG (30).28 (7).41 (10.3) RP-2916-SS RQ-2916-SS PG 29 PG (40).31 (8).45 (11.5) RP-2921-SS RQ-2921-SS PG 29 PG (40).31 (8).45 (11.5) RP-3621-SS RQ-3621-SS PG 36 PG (50).35 (9).49 (12.5) RP-3629-SS RQ-3629-SS PG 36 PG (50).35 (9).49 (12.5) RP-4229-SS RQ-4229-SS PG 42 PG (57).39 (10).53 (13.5) RP-4236-SS RQ-4236-SS PG 42 PG (57).39 (10).53 (13.5) RP-4836-SS RQ-4836-SS PG 48 PG (64).39 (10).53 (13.5) RP-4842-SS RQ-4842-SS PG 48 PG (64).39 (10).53 (13.5) una-n O-Rings can be substituted with Silicone or Viton O-Rings (see page 30). To order, add -S (Silicone) or -V (Viton ) to part number (e.g. RM-1612-SS-V) Viton is a federally registered trademark of upont ow Elastomer. imensions and specifications may be changed without prior notice. The 316 material is much harder and ideal for direct exposure to salt water and chemical solutions in marine, off-shore, pharmaceutical, etc. This special Stainless Steel Reducers are produced upon request only. Please allow for longer delivery times. W For inquiries - Please call our Inside Technical Sales epartment ( or ). More custom parts available online at or upon request! specifications. T

39 T W specifications. T Nickel Plated dapters, rass Liquid Reducers Tight & Strain Enlargers Relief Fittings Enlargers - Nylon & Nickel Plated rass Enlargers - PG to PG s Part Numbers s imensions in Inches (mm) Male Female T Outer iameter imensions and specifications may be changed without prior notice. EP-0709-R PG 7 PG 9.67 (17).20 (5).59 (15) EP-0911-R PG 9 PG (20).24 (6).65 (16.5) EP-0913-R PG 9 PG (22).24 (6).69 (17.5) EP-1113-R PG 11 PG (22).24 (6).69 (17.5) EP-1116-R PG 11 PG (24).24 (6).73 (18.5) EP-1121-R PG 11 PG (30).24 (6).81 (20.5) EP-1316-R PG 13 PG (24).26 (6.5).75 (19) EP-1321-R PG 13 PG (30).26 (6.5).83 (21) EP-1621-R PG 16 PG (30).26 (6.5).83 (21) EP-1629-R PG 16 PG (39).26 (6.5).88 (22.5) EP-2129-R PG 21 PG (39).28 (7).91 (23) EP-2936-R PG 29 PG (50).31 (8) 1.08 (27.5) EP-3642-R PG 36 PG (57).35 (9) 1.22 (31) EP-4248-R PG 42 PG (64).39 (10) 1.30 (33) Enlargers - Metric to Metric s Part Numbers s imensions in Inches (mm) Male Female T Outer iameter EM-1216-R M12 x 1.5 M16 x (18).20 (5).59 (15) EM-1620-R M16 x 1.5 M20 x (22).24 (6).69 (17.5) EM-2025-R M20 x 1.5 M25 x (27).26 (6.5).75 (19) EM-2532-R M25 x 1.5 M32 x (34).26 (6.5).83 (21) EM-3240-R M32 x 1.5 M40 x (42).28 (7).91 (23) EM-4050-R M40 x 1.5 M50 x (53).35 (9) 1.22 (31) EM-5063-R M50 x 1.5 M63 x (66).35 (9) 1.22 (31) Enlargers - NPT to NPT s Part Numbers s imensions in Inches (mm) Male Enlargers - Metric to Metric s Part Numbers s dapter Male Female Female T Outer iameter imensions in Inches (mm) T W Inner iameter EN-1234-R 1/2 NPT 3/4 NPT 1.10 (28).79 (20) 1.50 (38) EN-1210-R 1/2 NPT 1 NPT 1.36 (34.5).79 (20) 1.75 (44.5) EN-3410-R 3/4 NPT 1 NPT 1.38 (35).71 (18) 1.69 (43) EN-1054-R 1 NPT 1-1/4 NPT 1.73 (44).94 (24) 1.97 (50) EM-1216-K M12 x 1.5 M16 x (8).79 (20).26 (6.5).83 (21) EM-1620-K M16 x 1.5 M20 x (8).83 (21).35 (9).98 (25) EM-2025-K M20 x 1.5 M25 x (8).91 (23).55 (14) 1.18 (30) EM-2532-K M25 x 1.5 M32 x 1.5 C.59 (15) 1.18 (30).65 (16.5) N/ EM-3240-K M32 x 1.5 M40 x 1.5 C.59 (15) 1.36 (34.5).91 (23) N/ EM-4050-K M40 x 1.5 M50 x 1.5 C.59 (15) 1.36 (34.5) 1.18 (30) N/ EM-5063-K M50 x 1.5 M63 x 1.5 C.59 (15) 1.38 (35) 1.54 (39) N/ C Is your thread size off by one size? These Enlargers will solve that threading problem. They convert holes which fit PG, NPT or Metric threads to a larger female thread of the same thread type. T More custom parts available online at or upon request! Optional Locking Nuts, O-Rings & Other ccessories starting at page Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

40 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger Introduction Electrical Conduit provides protection to enclosed single or multi-conductors from impact, moisture, and chemical vapors. Varying quantities, sizes, and types of conductors can be pulled into a Conduit, which simplifies design and construction compared to multiple runs of cables or the expense of customized composite cables. s can be made waterproof. Cable connections between fixed and moving parts are weak spots in machine & system installations. When cables are bent, Operating Temperatures individual tensioned conductors have no room for flexing. They are subjected to high and variable tension forces, Push-In Fittings - 20ºC to 80ºC (- 4ºF to 176ºF) particularly multi-conductor cables. To prevent conductor breakages, the use of Conduit tubing is recommended. Turn-to-Seal Fittings - 40ºC to 110ºC (- 40ºF to 230ºF) dvantages: Individual conductors are given sufficient flexibility. This prevents tension stress. Connections provide security against penetration of fluids This STNR Corrugated Conduit is made of flame retardant Nylon. The Conduit is suitable for static and moderate dynamic installations. The SUPER-FLEX Conduit is made of a special plastic blend. ue to its higher flexibility, it is an ideal solution for drag chain and robotics applications. Sizes 8 & 14 are not available in this material. C Snapclic UO Nylon Snapclic UO rass ouble-seal Fittings Flange/ulkhead Fittings Standard Conduit Super-Flex Conduit Corrugated Conduit (Standard & Super Flex) Standard Modified Polyamide P 6 Part Numbers SuperFlex Thermoplastic Elastomer Corrugated Conduit Nominal Conduit Size Roll (feet) imensions and specifications may be changed without prior notice. - 40ºC to 100ºC (- 40ºF to 212ºF) - 40ºC to 100ºC (- 40ºF to 212ºF) - 40ºC to 110ºC (- 40ºF to 230ºF) - 20ºC to 80ºC (- 4ºF to 176ºF) - 40ºC to 110ºC (- 40ºF to 230ºF) - 50ºC to 160ºC (- 58ºF to 320ºF) imensions Inner ia.() x Outer ia.() Inches (mm) Fits Turn-to-Seal Fittings ST & ET SM-0811-K x.44 (8.5 x 11.2) PG 7, 1/4 NPT SM-1013-K SM-1013-Y x.51 (10 x 13) PG 7, 1/4 NPT, PG 9 SM-1216-K SM-1216-Y x.61 (12 x 15.5) PG 11, 3/8 NPT SM-1419-K x.73 (14 x 18.5) PG 13 SM-1721-K SM-1721-Y x.83 (16.5 x 21) PG 16, 1/2 NPT SM-2328-K SM-2328-Y x 1.12 (22.5 x 28.5) PG 21, 3/4 NPT SM-2934-K SM-2934-Y x 1.36 (28.5 x 34.5) PG 29, 1 NPT SM-3642-K SM-3642-Y x 1.65 (36 x 42) PG 36, 1-1/4 NPT SM-4854-K SM-4854-Y x 2.13 (47.5 x 54) PG 48, 2 NPT Part Numbers Snap-In Mounting rackets Fits Nominal Conduit Size M-09-K (12) 1.18 (30).91 (23).20 (5).35 (9) M-11-K (12) 1.18 (30).91 (23).20 (5).39 (10) M-16-K (15) 1.38 (35) 1.18 (30).24 (6).47 (12) M-21-K (16) 1.65 (42) 1.50 (38).26 (6.5).47 (12) E M-29-K (16) 2.01 (51) 1.93 (49).26 (6.5).47 (12) old conduit securely in place. M-36-K (18) 2.40 (61) 2.01 (51).26 (6.5).47 (12) M-48-K (19) 2.91 (74) 2.52 (64).26 (6.5).47 (12) Material: lack Nylon 6/6 Quick assembly thanks to single-hole fixing Simply snap in conduits 40 Mounting rackets imensions C E Width Mounting ole ø Mounting ole Recess ø

41 Part Numbers Fits Nominal Conduit Size Push-In Conduit Fittings Push-In Conduit Fittings Straight Fittings - imensions in Inches (mm) Elbow Fitting - imensions in Inches (mm) Straight Fitting Elbow Fitting C E F G Clearance ole +.01 (+.25 mm) ody Clearance ole SM09-K EM09-K PG (15.2).31 (8).91 (23).67 (17).60 (15.2).31 (8) 1.69 (43).91 (23).75 (19) SM11-K EM11-K PG (18.5).31 (8).98 (25).83 (21).73 (18.5).31 (8) 1.89 (48) 1.06 (27).87 (22) SM13-K EM13-K PG (20.3).35 (9) 1.10 (28).94 (24).80 (20.3).35 (9) 2.04 (52) 1.20 (30.5).94 (24) SM16-K EM16-K PG (22.3).39 (10) 1.14 (29) 1.06 (27).88 (22.3).39 (10) 2.20 (56) 1.28 (32.5) 1.06 (27) SM21-K EM21-K PG (28.4).43 (11) 1.26 (32) 1.38 (35) 1.12 (28.4).43 (11) 2.76 (70) 1.57 (40) 1.30 (33) SM29-K EM29-K PG (37.3).43 (11) 1.38 (35) 1.65 (42) 1.47 (37.3).43 (11) 3.27 (83) 2.03 (51.5) 1.65 (42) SM36-K - PG (47).51 (13) 1.61 (41) 1.97 (50) SM48-K - PG (59.4).55 (14) 1.81 (46) 2.52 (64) SM09N-K EM09N-K 3/8 NPT (17.2).60 (15).91 (23).67 (17).68 (17.2).60 (15) 1.69 (43).91 (23).75 (19) SM16N-K EM16N-K 1/2 NPT (21.1).51 (13) 1.14 (29) 1.06 (27).83 (21.1).51 (13) 2.20 (56) 1.28 (32.5) 1.06 (27) SM21N-K EM21N-K 3/4 NPT (26.7).51 (13) 1.26 (32) 1.38 (35) 1.05 (26.7).51 (13) 2.76 (70) 1.57 (40) 1.30 (33) SM29N-K EM29N-K 1 NPT (34.3).59 (15) 1.38 (35) 1.65 (42) 1.35 (34.3).59 (15) 3.27 (83) 2.03 (51.5) 1.65 (42) ody ody Nickel Plated rass Nylon Strain Relief SM16M-K EM16M-K M16 x (16).31 (8).91 (23).67 (17).63 (16).31 (8) 1.69 (43).91 (23).75 (19) SM20M-K EM20M-K M20 x (20).35 (9) 1.10 (28).94 (24).79 (20).35 (9) 2.04 (52) 1.20 (30.5).94 (24) SM25M-K EM25M-K M25 x (25).43 (11) 1.26 (32) 1.38 (35).98 (25).43 (11) 2.76 (70) 1.57 (40) 1.30 (33) SM32M-K EM32M-K M32 x (32).43 (11) 1.38 (35) 1.65 (42) 1.26 (32).43 (11) 3.27 (83) 2.03 (51.5) 1.65 (42) Optional Locking Nuts, O-Rings & Other ccessories starting at page 28. SM & EM Fittings feature a Locking Ridge to hold Conduit Tubing in place. SM - Straight The fastest and most labor saving method to connect flexible Nylon Conduit to a Push-in Fitting. The Nylon Conduit is inserted into the Fitting until the hook snaps over the ridge of the Corrugated Tubing. The Conduit can be mounted rigid for liquid tight (NEM 4x) or turnable for non-liquid tight (NEM 2). EM - 90 Snap Elbows Combines the unique 90 Snap Elbow and Straight Push-in Fitting for easy installation of wires into an Elbow Fitting. The Straight Elbow is snapped together after the wires have been installed, resulting in a liquid tight 90 Elbow. They also have an O-Ring groove for optional O-Ring installation. imensions and specifications may be changed without prior notice. G E F () C () Suggested Clearance ole for Non-ed Mounting 41 ccessories dapter,reducer,enlarger

42 Nickel Plated rass Nylon Strain Relief Conduit Fittings: Turn-to-Seal The Turn-to-Seal family consists of Conduit Fittings manufactured from high-grade polyamide. This design means that the Fittings offer a high protection rating of IP 65 (NEM 4). The Fittings are completely pre-assembled and no additional parts such as cap nuts and clamping rings need to be fitted, ensuring reliability in assembly. The cable protection Conduit can be assembled quickly and easily by simply inserting the Conduit and turning the cap nut. The Elbow has smooth inside walls, making the installation of cables & wires easy. Part Numbers Fits Nominal Conduit Size Turn-To-Seal Conduit Fittings Straight Fitting - imensions in Inches (mm) Elbow - imensions in Inches (mm) C E F G I J ody (ody) (ome) Inside iameter Elbow Elbow (ome) Inside iameter ST07-K - PG (8) 1.02 (26).75 (19).87 (22).31 (8) ST07R-K - PG (8) 1.02 (26).75 (19).87 (22).31 (8) ST09-K ET09-K PG (8) 1.02 (26).75 (19).87 (22).43 (11).30 (7.5) 1.77 (45) 1.02 (26).87 (22).39 (10) ST11-K ET11-K PG (8) 1.02 (26).87 (22).94 (24).55 (14).31 (8) 2.01 (51) 1.10 (28).94 (24).51 (13) ST16-K ET16-K PG (8) 1.02 (26) 1.06 (27) 1.18 (30).67 (17).39 (10) 2.20 (56) 1.26 (32) 1.18 (30).63 (16) ST21-K ET21-K PG (10) 1.38 (35) 1.46 (37) 1.50 (38).91 (23).43 (11) 2.64 (67) 1.50 (38) 1.50 (38).87 (22) ST29-K ET29-K PG (10) 1.38 (35) 1.77 (45) 1.81 (46) 1.22 (31).47 (12) 3.23 (82) 1.97 (50) 1.81 (46) 1.14 (29) ST36-K - PG (15) 1.81 (46) 2.17 (55) 2.40 (61) 1.54 (39) ST48-K - PG (15) 1.97 (50) 2.52 (64) 2.91 (74) 2.01 (51) ccessories ST11N-K ET11N-K 3/8 NPT (14) 1.02 (26).87 (22).94 (24).47 (12).31 (8) 2.01 (51) 1.10 (28).94 (24).51 (13) ST16N-K ET16N-K 1/2 NPT (13) 1.02 (26) 1.06 (27) 1.18 (30).55 (14).39 (10) 2.20 (56) 1.26 (32) 1.18 (30).63 (16) ST21N-K ET21N-K 3/4 NPT (14) 1.38 (35) 1.46 (37) 1.50 (38).75 (19).43 (11) 2.64 (67) 1.50 (38) 1.50 (38).83 (21) ST29N-K ET29N-K 1 NPT (19) 1.38 (35) 1.81 (46) 1.81 (46) 1.02 (26).47 (12) 3.23 (82) 1.97 (50) 1.81 (46) 1.06 (27) ST36N-K - 1-1/4 NPT (18) 1.81 (46) 2.17 (55) 2.40 (61) 1.38 (35) dapter,reducer,enlarger ST & ET Fittings are V0 rated & have IP 65 protection without additional parts (O-Ring or Seal Ring). 42 dvantages: ST - Straight Conduit Fittings with plastic thread Reliable assembly as fitting is supplied pre-assembled. No additional parts required Integrated clamping ring ensures high tear-out strength igh protection to IP 65 (NEM 4) without additional parts Can be opened without tools ET - 90 ngled Conduit Fittings with plastic thread Reliable assembly as fitting is supplied pre-assembled. No additional parts required Integrated clamping ring ensures high tear-out strength igh protection to IP 65 without additional parts Can be opened without tools Smooth inside walls, therefore easy insertion of the cables into the 90 angle igh protection rating of IP 65 (NEM 4) One-part fitting Rapid assembly igh pull-out resistance Inner contours of 90 fittings are rounded () imensions and specifications may be changed without prior notice. E (C) (I) G Optional Locking Nuts, O-Rings & Other ccessories starting at page 28. J F

43 Combination of Strain Relief & Conduit Fittings Push-in system Partially rotatable Can be equipped with Multi-ole inserts Metal style can be changed to EMI/RFI C F 1 Conduit Fittings: Snapclic UO Part Numbers Cable Range Inches (mm) UO11-K (5-10) UO11R-K (3-7) UO13-K (6-12) UO13R-K (5-9) UO16-K (10-14) UO16R-K (7-12) UO21-K (13-18) UO21R-K (9-16) UO29-K (18-24) UO29R-K (13-20) UO36-K (22-31) UO36R-K (20-26) Snapclic UO - Nylon Fits Nominal Conduit Size ole O.. Snapclic UO - Nickel Plated rass Part Numbers Cable Range Fits imensions Nominal Conduit C F 1 Size ole O.. ody Outer Inches (mm) +.01 (+.25 mm) iameter UO11-R (5-10) UO11R-R (3-7) PG (18.5).24 (6) 1.52 (38.5).91 (23).79 (20) UO13-R (6-12) UO13R-R (5-9) PG (20.3).24 (6) 1.56 (39.5).98 (25).87 (22) UO16-R (10-14) UO16R-R (7-12) PG (22.3).24 (6) 1.63 (41.5) 1.14 (29).94 (24) UO21-R (13-18) UO21R-R (9-16) PG (28.4).28 (7) 1.75 (44.5) 1.18 (30) 1.18 (30) UO29-R (18-24) UO29R-R (13-20) PG (37.3).31 (8) 2.07 (52.5) 1.54 (39) 1.57 (40) UO36-R (22-31) UO36R-R (20-26) PG (47).31 (8) 2.32 (59) 1.77 (45) 1.97 (50) UO16M-R (5-10) UO16MR-R (3-7) M16 x (16).24 (6) 1.52 (38.5).91 (23).79 (20) UO20M-R (6-12) UO20MR-R (5-9) M20 x (20).24 (6) 1.56 (39.5).98 (25).87 (22) UO22M-R (10-14) UO22MR-R (7-12) M20 x (20).24 (6) 1.63 (41.5) 1.14 (29).94 (24) UO25M-R (13-18) UO25MR-R (9-16) M25 x (25).28 (7) 1.75 (44.5) 1.18 (30) 1.18 (30) UO32M-R (18-24) M32 x 1.5 UO32MR-R (13-20) (32).31 (8) 2.07 (52.5) 1.54 (39) 1.57 (40) UO40M-R (22-31) M40 x 1.5 UO40MR-R (20-26) (40).31 (8) 2.32 (59) 1.77 (45) 1.97 (50) imensions and specifications may be changed without prior notice. imensions C F (+.25 mm) ody Outer iameter PG (18.5).31 (8) 1.65 (42).98 (25).87 (22) PG (20.3).35 (9) 1.73 (44).98 (25).94 (24) PG (22.3).39 (10) 1.81 (46) 1.18 (30) 1.06 (27) PG (28.4).43 (11) 1.97 (50) 1.38 (35) 1.30 (33) PG (37.3).43 (11) 2.36 (60) 1.65 (42) 1.65 (42) PG (47).51 (13) 2.36 (60) 1.97 (50) 2.09 (53) UO16M-K (5-10) UO16MR-K (3-7) M16 x (16).31 (8) 1.65 (42).98 (25).87 (22) UO20M-K (6-12) UO20MR-K (5-9) M20 x (20).35 (9) 1.73 (44).98 (25).94 (24) UO22M-K (10-14) UO22MR-K (7-12) M20 x (20).39 (10) 1.81 (46) 1.18 (30) 1.06 (27) UO25M-K (13-18) UO25MR-K (9-16) M25 x (25).43 (11) 1.97 (50) 1.38 (35) 1.30 (33) UO32M-K (18-24) M32 x 1.5 UO32MR-K (13-20) (32).43 (11) 2.36 (60) 1.65 (42) 1.65 (42) UO40M-K (22-31) M40 x 1.5 UO40MR-K (20-26) (40).51 (13) 2.36 (60) 1.97 (50) 2.09 (53) Suggested Clearance ole for Non-ed Mounting Optional Locking Nuts, O-Rings & Other ccessories starting at page 28. Pressure Rating: Installation side - IP 68 (10 bar) Conduit side - IP 54 C F 1 43 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

44 Nickel Plated rass Nylon Strain Relief Part Numbers Nickel Plated rass Technical Conduit Liquid Information Tight System Strain Relief Fittings Conduit Fittings: ouble-seal & ulkhead Cable Range Inches (mm) ouble-seal Fittings Fits Nominal Conduit Size imensions C F 1 ole O (+.25 mm) ody S09-K PG (4-8) (15.2).31 (8) 1.73 (44).75 (19) /.87 (22) S11-K PG (5-10) (18.5).31 (8) 1.85 (47).87 (22) /.95 (24) S13-K PG (6-12) (20.3).35 (9) 1.93 (49).95 (24) / 1.18 (30) S16-K PG (10-14) (22.3).39 (10) 1.97 (50) 1.06 (27) / 1.18 (30) S21-K PG (13-18) (28.4).43 (11) 2.32 (59) 1.30 (33) / 1.50 (38) dvantages: Combined Conduit and Cable Fitting 2-in-1 Clamping around entire circumference, ensuring maximum pull-out resistance No loose parts - Fitting does not have to be dismantled for assembly igh degree of protection C S09N-K 3/8 NPT (4-8) (17.2).59 (15) 2.01 (51).75 (19) /.87 (22) S13N-K 1/2 NPT (6-12) (21.1).51 (13) 2.09 (53).95 (24) / 1.18 (30) S16N-K 1/2 NPT (10-14) (21.1).51 (13) 2.09 (53) 1.06 (27) / 1.18 (30) S21N-K 3/4 NPT (13-18) (26.7).51 (13) 2.40 (61) 1.30 (33) / 1.50 (38) S16M-K M16 x (4-8) (16).31 (8) 1.73 (44).75 (19) /.87 (22) S20M-K M20 x (6-12) (20).35 (9) 1.93 (49).95 (24) / 1.18 (30) S25M-K M25 x (13-18) (25).43 (11) 2.32 (59) 1.30 (33) / 1.50 (38) F 1 Suggested Clearance ole for Non-ed Mounting ccessories dapter,reducer,enlarger dvantages: Split system enables pre-assembled cables to be inserted by means of removable upper part Easy assembly igh stability Supplied with gasket for flange connection. Internal thread for Metric and PG Fittings dvantages: Split system enables pre-assembled cables to be inserted by means of removable upper part Easy assembly igh stability Supplied with gasket for flange connection. Conduit remains rotatable 44 E C Part Numbers E (up to M25 / PG 21) (from to M32 / PG 29) For Material (Technical Specifications rawings apply please to both types refer of ulkhead to page Fittings) 45. ulkhead Conduit Fittings with Fits Nominal Conduit Size imensions and and specifications may may be be changed without prior prior notice. imensions in Inches (mm) C E Width istance between oles ole iameter FL-11-K PG (49) 1.85 (47) 1.38 (35) 1.46 (37).20 (5) FL-13-K PG (49) 1.85 (47) 1.38 (35) 1.46 (37).20 (5) FL-21-K PG (69) 2.56 (65) 1.73 (44) 2.05 (52).26 (6.5) FL-29-K PG (90) 3.07 (78) 2.17 (55) 2.56 (65).28 (7) FL-36-K PG (100) 3.70 (94) 2.60 (66) 3.15 (80).28 (7) FL-48-K PG (116) 3.98 (101) 2.99 (76) 3.46 (88).28 (7) ulkhead Conduit Fittings without Part Numbers Fits Nominal Conduit Size imensions in Inches (mm) C E Width istance between oles ole iameter FT-11-K (49) 1.85 (47) 1.38 (35) 1.46 (37).20 (5) FT-13-K (49) 1.85 (47) 1.38 (35) 1.46 (37).20 (5) FT-21-K (69) 2.56 (65) 1.73 (44) 2.05 (52).26 (6.5) FT-29-K (90) 3.07 (78) 2.17 (55) 2.56 (65).28 (7) FT-36-K (100) 3.70 (94) 2.60 (66) 3.15 (80).28 (7) FT-48-K (116) 3.98 (101) 2.99 (76) 3.46 (88).28 (7) C Note: Screws not included. ulkhead Fittings are manufactured from high-grade polyamide. Split system: large cut-out size allows for quick & easy insertion of pre-assembled cables into a housing. Protection rating: IP 54 or IP 65. The higher IP 65 protection rating is achieved in combination with a suitable Conduit Fitting. Note: The design of the ulkhead Fittings changes depending on size. Up to M25/PG 21 the Fitting has 3 screw holes, from size M32 / PG 29 the Fitting has 4 screw holes. (see technical drawings)

45 Pressure Rating: V0 Flammability Rating according to UL 94 (applies to all Strain Relief Fittings) Nickel Plated rass Technical Liquid Information Tight Strain Relief Fittings Nylon 150 PSIG (10 R) NEM 4x, 6 (Submersible) & 12 - IP 68 / IP 69K Materials: Fittings: Nylon 6/6 Form Seal: una-n Optional O-Ring: una-n, Viton or Silicone Optional Seal Ring: Polyethylene or Fiber-Reinforced Plastic Operating Temperature: Nylon Fittings: - 40ºC to 100ºC (- 40ºF to 212ºF) Nylon Fitting w/ luminum Clamp: - 20ºC to 70ºC (- 4ºF to 158ºF) vailable Colors: lack (RL 9005) Gray (RL 7035) lue (RL 5012) - upon request Nylon 6/6: V0 rated - Flame resistant, halogen and phosphorous free, self-extinguishing, non-toxic, fungus resistant Pressure Rating: Nickel Plated rass 150 PSIG (10 R) NEM 4x, 6 (Submersible) & 12 - IP 68 / IP 69K Materials: Fittings: Nickel Plated rass Spring (Flex Extension): Stainless Steel Form Seal: una-n (NR) Splined ushing: Nylon 6/6 O-Ring: una-n (Viton or Silicone optional) Optional Seal Ring: Polyethylene or Fiber-Reinforced Plastic Operating Temperature: - 40ºC to 100ºC (- 40ºF to 212ºF) Nylon 6/6: V0 rated - Flame resistant, halogen and phosphorous free, self extinguishing, non-toxic, fungus resistant Mini WI (una-n) Mini WI (Viton ) WI XL (una-n) dapter, Reducer & Enlarger Materials Materials Nylon Nickel Plated rass Nickel Plated rass - WI Operating Temperatures - 20ºC to 100ºC (- 4ºF to 212ºF) - 25ºC to 200ºC (- 13ºF to 392ºF) - 20ºC to 100ºC (- 4ºF to 212ºF) Operating Temperatures - 40ºC to 80ºC (- 40ºF to 176ºF) - 40ºC to 100ºC (- 40ºF to 212ºF) Viton and Teflon are federally registered trademarks of upont ow Elastomer. Material Specifications Pressure Rating: imensions and specifications may be changed without prior notice. PVF 150 PSIG (10 R) NEM 4x, 6 (Submersible) & 12 - IP 68 / IP 69K Materials: Fittings: Teflon or Nickel Plated rass Form Seal: Viton (FPM) Clamping Insert: PVF O-Ring: Viton (FPM) Operating Temperature: - 35ºC to 150ºC (- 31ºF to 302ºF), V0 rated Pressure Rating: Stainless Steel Resistant to: 150 PSIG (10 R) NEM 4x, 6 (Submersible) & 12 - IP 68 / IP 69K Materials: Fittings: 303 Stainless Steel Form Seal: una-n (NR) or Viton (FPM) Clamping Insert: P (Nylon) or PVF O-Ring: una-n (FPM), Viton or Silicone Operating Temperature: una-n: - 40ºC to 100ºC (- 40ºF to 212ºF) PVF: - 35ºC to 150ºC (- 31ºF to 302ºF) Materials una-n Elastomer Viton (FPM) Silicone Materials Insert Materials Operating Temperatures - 40ºC to 100ºC (- 40ºF to 212ºF) - 40ºC to 100ºC (- 40ºF to 212ºF) - 25ºC to 200ºC (- 13ºF to 392ºF) - 60ºC to 250ºC (- 76ºF to 482ºF) O-Ring & Seal Ring Materials una-n Viton (FPM) Silicone Polyethylene Fiber-reinforced Plastic cid Salt solution Oxydant alogens lcohols Chlorinated solvent liphatic hydrocarbons Petrol Operating Temperatures - 30ºC to 120ºC (- 22ºF to 248ºF) - 40ºC to 200ºC (- 40ºF to 392ºF) - 60ºC to 250ºC (- 76ºF to 482ºF) - 30ºC to 70ºC (- 22ºF to 158ºF) - 55ºC to 300ºC (- 67ºF to 572ºF) UL/UR E CS VE CGE ZERO UE114 PTENT Most of our standard products are also available in EEx e & TEX versions! Call for Technical ssistance: / Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

46 Nickel Plated rass Nylon Strain Relief Nickel Plated rass Technical Liquid Information Tight Strain Relief Fittings NEM Ratings - Overview NEM stands for the National Electrical Manufacturers ssociation. It has established a range of standards for electrical equipment enclosures. NEM 1 General Purpose - Indoors 1 - intended for general purpose indoor use primarily to provide a degree of protection against contact with the enclosed equipment or locations where unusual service conditions do not exist. NEM 2 rip Proof - Indoors 2 - intended for general purpose indoor use primarily to provide a degree of protection against limited amounts of falling water and dirt. NEM 3 ust Tight, Rain Tight, & Ice/Sleet resistant - Indoors/Outdoors 3 - intended for general purpose outdoor use primarily to provide a degree of protection against windblown dust, rain, and sleet; and to be undamaged by the formation of ice on the enclosure. ccessories NEM 3R Rain Proof & Ice/Sleet Proof - Indoors/Outdoors 3R - intended for general purpose outdoor use primarily to provide a degree of protection against falling rain; and to be undamaged by the formation of ice on the enclosure. NEM 3S ust Tight, Rain Tight, & Ice/Sleet Proof - Outdoors 3S - intended for general purpose outdoor use primarily to provide a degree of protection against sleet; and to be undamaged by the formation of ice on the enclosure. NEM 4 Water Tight & ust Tight - Indoors/Outdoors 4 - intended for general purpose indoor or outdoor use primarily to provide a degree of protection against windblown dust and rain, splashing water, and hose directed water; and to be undamaged by the formation of ice on the enclosure. NEM 4x Water Tight, ust Tight, & Corrosion Resistant - Indoors/Outdoors 4X - intended for general purpose indoor and outdoor use primarily to provide a degree of protection against corrosion, windblown dust and rain, splashing water, and hose-directed water; and to be undamaged by the formation of ice on the enclosure. NEM 5 Superseded by NEM 12 for Control pparatus 5 - see NEM 12 dapter,reducer,enlarger 46 NEM 6 Submersible, Water Tight, ust Tight, & Ice/Sleet Resistant - Indoors/Outdoors 6 - intended for general purpose indoor or outdoor use primarily to provide a degree of protection against the entry of water during temporary submersion at a limited depth; and to be undamaged by the formation of ice on the enclosure. NEM 6P Submersible, Water Tight, ust Tight, & Ice/Sleet Resistant - Indoors/Outdoors 6P - Same as NEM 6 including protection against the entry of water during prolonged submersion at a limited depth. NEM 7 Underwriters Lab Class 1-Groups C& -Explosion Proof - Indoors 7 - for indoor use in locations classified as Class I, Groups,, C, or, as defined in the National Electrical Code. 7 enclosures shall be capable of withstanding the pressures resulting from an internal explosion of specified gases, and contain such an explosion sufficiently that an explosive gas-air mixture existing in the atmosphere surrounding the enclosure will not be ignited. Enclosed heat generating devices shall not cause external surfaces to reach temperatures capable of igniting explosive gas-air mixtures in the surrounding atmosphere. Enclosures shall meet explosion, hydro-static, and temperature design tests. NEM 8 Underwriters Lab Class 1-Groups C& -Explosion Proof - Indoors 8 is same as NEM 7, except the unit is oil-immersed NEM 9 Underwriters Lab Class II - Groups E, F, G - Indoors 9 - intended for special purpose indoor use in locations classified as hazardous (Class II, Groups E, F, or G, as defined in the National Electrical Code). 9 enclosures shall be capable of preventing the entrance of dust. Enclosed heat generating devices shall not cause external surfaces to reach temperatures capable of igniting or discoloring dust on the enclosure or igniting dust-air mixtures in the surrounding atmosphere. Enclosures shall meet dust penetration and temperature design tests, and aging of gaskets (if used). NEM 10 ureau of Mines NEM 11 Corrosion Resistant & rip Proof - Oil Immersed - Indoors NEM 12 Industrial Use - ust Tight & rip Tight - Indoors 12 - intended for industrial indoor use primarily to provide a degree of protection against dust, falling dirt, and dripping noncorrosive liquids. NEM 13 Oil Tight & ust Tight - Indoors 13 - intended for industrial indoor use primarily to provide a degree of protection against dust, spraying of water, oil, and noncorrosive coolant. NEM Rating NEM 1 NEM 2 NEM 3 NEM 3R NEM 3S NEM 4 NEM 4x NEM 6 NEM 6P NEM 12, 12K NEM 13 IP Class IP 23 IP 30 IP 64 IP 32 IP 64 IP 66 IP 66 IP IP IP 65 IP 65 Indoor Outdoor Indoor & Outdoor imensions and specifications may be changed without prior notice. Call for Technical ssistance: /

47 Nickel Plated rass Technical Liquid Information Tight Strain Relief Fittings IP Ratings The IP Code defined in international standard IEC classifies the degrees of protection provided against the intrusion of: solid objects (including body parts like hands and fingers) dust accidental contact water in electrical enclosures It consists of the letters IP (for International Protection Rating or Ingress Protection Rating ) followed by two digits and an optional letter. The standard aims to provide users more detailed information than vague marketing terms such as waterproof. Level Object size protected against Effective against 0 - No protection against contact and ingress of objects 1 >50 mm ny large surface of the body, such as the back of a hand, but no protection against deliberate contact with a body part 2 >12.5 mm Fingers or similar objects 3 >2.5 mm Tools, thick wires, etc. 4 >1 mm Most wires, screws, etc. 5 dust protected Ingress of dust is not entirely prevented, but it must not enter in sufficient quantity to interfere with the satisfactory operation of the equipment; complete protection against contact 6 dust tight No ingress of dust; complete protection against contact Level Protected against etails 0 not protected - 1 dripping water ripping water (vertically falling drops) shall have no harmful effect. 2 dripping water when tilted up to 15 Vertically dripping water shall have no harmful effect when the enclosure is tilted at an angle up to 15 from its normal position. 3 spraying water Water falling as a spray at any angle up to 60 from the vertical shall have no harmful effect. 4 splashing water Water splashing against the enclosure from any direction shall have no harmful effect. 5 water jets Water projected by a nozzle against enclosure from any direction shall have no harmful effects. 6 powerful water jets Water projected in powerful jets against the enclosure from any direction shall have no harmful effects. 7 immersion up to 1 m Ingress of water in harmful quantity shall not be possible when the enclosure is immersed in water under defined conditions of pressure and time (up to 1 m of submersion). 8 immersion beyond 1 m The equipment is suitable for continuous immersion in water under conditions which shall be specified by the manufacturer. NOTE: Normally, this will mean that the equipment is hermetically sealed. owever, with certain types of equipment, it can mean that water can enter but only in such a manner that produces no harmful effects. IP 69K German standard IN extends the IEC rating system described above with an IP 69K rating for high-pressure, high-temperature wash-down applications. Such enclosures must not only be dust tight (IP 6X), but also able to withstand high-pressure and steam cleaning. The test specifies a spray nozzle that is fed with 80 C (176 F) water at 8 10 MPa ( bar) and a flow rate of L/min. The nozzle is held cm ( ) from the tested device at angles of 0, 30, 60 and 90 for 30 seconds each. The test device sits on a turntable that rotates once every 12 s (5 rpm). The IP 69K test specification was initially developed for road vehicles, especially those that need regular intensive cleaning (dump trucks, cement mixers, etc), but also finds use in other areas (e.g., food industry, railroad, marine, etc.) The most commonly used protection methods are IP and NEM, whereas: IP Classification addresses the European market NEM Classification addresses the North merican market For questions please call our Inside Technical Sales epartment or imensions and specifications may be changed without prior notice. 47 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

48 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 48 Nickel Plated rass Technical Liquid Information Tight Strain Relief Fittings Sizes & imensions for SELCON Liquid Tight Strain Relief Fittings etermine Sizes & of Fitting: Metric Major iameter Minor iameter Check markings on the hex portion (wrenching flats). PG, NPT or Metric size should be embedded. This only applies to Nylon parts. Measure major thread diameter and compare with chart above. This may tell you whether it is a PG, NPT or Metric thread (Nylon or rass) Confirm grommet type inside fitting. (See table on right for grommet identification) The shorter length fittings are C s (connector dome), the longer type are CF s (connector flex). We offer Enlarged as well as Reduced solutions. PG13.5/16 has a PG13 thread with a PG16 body. Reduced would be the opposite (only in Nylon) The shading (grouping) indicates same size bodies, but different threads. NOTE: ome Opening = the largest possible dimension for one or more cables. The chart can also be useful when working with knockouts (drilling holes) PG Major iameter Minor iameter For Material Specifications For questions please call refer our Inside to page Technical 45. Sales epartment or NPT imensions and specifications may be changed without prior notice. Major iameter Minor iameter ome Opening M6 x mm / mm / mm /.11 M8 x mm / mm / mm /.19 M10 x mm / mm / mm /.24 M mm / mm / mm /.26 PG mm / mm /.44 1/ mm / mm / mm /.26 PG mm / mm /.54 3/ mm / mm / mm /.31 M16 x mm / mm / mm /.31 PG mm / mm / mm /.39 M20 x mm / mm / mm /.47 PG mm / mm /.75 1/ mm / mm / mm /.47 PG mm / mm /.83 1/2 -E 20.8 mm / mm / mm /.55 M25 x mm / mm / mm /.71 PG mm / mm / / mm / mm / mm /.71 M32 x mm / mm / mm / 0.98 PG mm / mm / mm / mm / mm / / mm / mm / mm / 0.98 M40 x mm / mm / mm / 1.26 PG mm / mm / / mm / mm / mm / 1.26 M50 x mm / mm / mm / 1.50 PG mm / mm / mm / 1.50 PG mm / mm / mm / 1.73 M63 x mm / mm / mm / 1.73 Recommended Torque Specifications for Strain Relief Fittings Torque in inlb (Nm) Sizes Plastic Fittings Metal Fittings ome Nuts & Lock Nuts ome Nuts & Lock Nuts PG7, M12x (1.62) 22.1 (2.5) 36.9 (4.17) 55.3 (6.25) PG9, PG11, PG13, 3/8 NPT, 1/2 NPT, M16x1.5, M20x (2.5) 33.2 (3.75) 36.9 (4.17) 55.3 (6.25) PG16, 1/2 NPT-E 29.5 (3.33) 44.2 (5) 44.2 (5) 66.4 (7.5) PG21, PG29, PG36, PG42, PG48, 3/4 NPT, 1 NPT, 1-1/4 NPT, 1-1/2 NPT, M25, M32, M40, M50, M (5) 66.4 (7.5) 59 (6.67) 88.5 (10) Note: Grommet Identification Color of Grommet lack Standard Gray Reduced eige Multi-ole / Solid Plug Green Viton rown Silicone Torque for dome nuts was determined using a metal rod. It may vary for cable, depending on the crush resistance of the cable. We recommend to determine the actual torque empirically, testing the actual cable used. The values shown above are for reference only. Pull-Test Rating for Strain Relief Fittings The Pull-Test Rating of our Strain Relief Fittings complies with Industry Standards. Pull-Test Rating: 35 lb. Viton is a federally registered trademark of upont ow Elastomer.

49 Nickel Plated rass Technical Liquid Information Tight Strain Relief Fittings Specifications NPT s Size 1/4 NPT 3/8 NPT 1/2 NPT 3/4 NPT 1 NPT 1-1/4 NPT 1-1/2 NPT 2 NPT Major ia. in Inches (mm).54 (13.72).69 (17.15).84 (21.34) 1.05 (26.67) 1.32 (33.40) 1.66 (42.16) 1.90 (48.26) 2.38 (60.33) Pitch in Inches (mm).056 (1.41).056 (1.41).071 (1.81).071 (1.81).087 (2.21).087 (2.21).087 (2.21).087 (2.21) s per Inch º Pitch conicity: 6.25% NPT = National Pipe Taper rate for all NPT threads is 1/16 The taper on NPT threads allows them to form a seal when torqued as the flanks of the threads compress against each other, as opposed to straight thread fittings Nickel Plated rass Nylon Strain Relief 90º Metric s Size M6 M8 M10 M12 M16 M20 M25 M32 M40 M50 M63 Major ia. in Inches (mm).24 (6).31 (8).39 (10).47 (12).63 (16).79 (20).98 (25) 1.26 (32) 1.57 (40) 1.97 (50) 2.48 (63) Pitch in Inches (mm).04 (1).05 (1.25).06 (1.5).06 (1.5).06 (1.5).06 (1.5).06 (1.5).06 (1.5).06 (1.5).06 (1.5).06 (1.5) 60º Pitch World-wide most commonly used type thread Characterized by its major diameter and its pitch esignated by the letter M followed by the value of the nominal diameter and the pitch, both expressed in millimeters and separated by the multiplication sign (i.e. M12 x 1.5) ccessories PG s Size PG 7 PG 9 PG 11 PG 13.5 PG 16 PG 21 PG 29 PG 36 PG 42 PG 48 Major ia. in Inches (mm).49 (12.5).60 (15.2).73 (18.6).80 (20.4).89 (22.5) 1.11 (28.3) 1.46 (37) 1.85 (47) 2.13 (54) 2.39 (59.3) Pitch in Inches (mm).05 (1.27).055 (1.41).055 (1.51).055 (1.51).055 (1.51).062 (1.59).062 (1.59).062 (1.59).062 (1.59).062 (1.59) 80º Pitch PG = Panzer-Gewinde (also Panzer-Rohr-Gewinde) German thread type epth of thread smaller than NPT or Metric, but larger flank angle SPP s Size 2-1/2 3 4 Major ia. in Inches (mm) 2.96 (75.84) 3.46 (87.88) 4.45 (113.03) Pitch in Inches (mm).09 (2.31).09 (2.31).09 (2.31) s per Inch º Pitch SPP = ritish Standard Pipe Parallel Parallel (straight) thread with a constant diameter, denoted by the letter G Symmetrical V-thread in which the angle between the flanks is 55 (measured in an axial plane) One-sixth of this sharp V is truncated at the top and the bottom s are rounded equally at crests and roots by circular arcs ending tangentially with the flanks The theoretical depth of the thread is therefore 0.64 times the nominal pitch For questions please call our Inside Technical Sales epartment For Material Specifications or please refer to page 45. imensions and specifications may be changed without prior notice. 49 dapter,reducer,enlarger

50 Nickel Plated rass Nylon Strain Relief M40 M23 Power Other Products Circular Connectors M16, M23, M40 Push-Pull M27 Signal M23 RJ45 Industrial Ethernet M23 Signal ccessories dapter,reducer,enlarger 50 M16 M23 Over-Molded Cord-sets M23 Stainless Steel Why use Sealcon / ummel Circular Connectors? Easy field assembly No special tools required to insert or extract contacts Modular for a variety of configurations ll Connectors are EMI Ready ed and Push-Pull (Quick isconnect) Interchangeable Compatible with other IN Style Connectors Reliable connection Contacts with low plug-in force and high mating cycles Pre-Tinned contacts Reliable, faster and safer means of soldering Vibration Safe Contacts (SLS) Inserts for all types of contacts Crimp, Solder & ip Solder Reduced Number of parts Time-Saving Cable ssembly ighest Ratings Large ssortment No Minimum omestic Inventory Orders! Excellent customer service Solar Wind Motors Lighting Robotics Telecom Industries Served utomation Packaging iagnostic Sensing Military utomotive Request Your Catalog Today: / /info@sealconusa.com Food & everage Marine Medical Traffic Pharmaceutical Transportation ISO 9001:2000 M23 ProfiNet 2 / 3 C vailable!

51 Materials: PC (Polycarbonate) S (cryl-utadiene-styrene) EMI Proof Polycarbonate Polyester Polystyrene luminum Powder-coated Steel Stainless Steel Other Products Industrial Enclosure Solutions Features: Square / rectangle shape Solid and transparent lids (PC & S) Smooth walls or PG/Metric knockouts (Medium PC/S) Knockout & Membrane Flanges (Large PC/S) Extension Frames (Large PC/S) inges & Latches (PC) EMI Shielding (PC EMI) ccessories: Mounting Plates, IN Rails, Lugs, Clips, Screws, Key, etc. Nickel Plated rass Nylon Strain Relief We will be happy to help you choose the correct enclosure for your application. We also provide customization by replacing standard parts with special options. rilling and Cutting We perform customized machining such as cutting, drilling, threading and countersinking according to drawings. inged / Latched ssembly The enclosures can be equipped with: Cable glands Flanges Circular connectors IN Rails Mounting Plates inges, etc. Print Company logos, operating instructions and picture symbols can easily be silk screen printed on the enclosures. The enclosures feature a clean and functional style. Color Service In addition to the standard gray color, we also offer other color options. For large series, dyed raw material is the most cost-effective color option. Small series can be painted according to the RL color scale. We offer total solutions! Creative Flexible Economical We offer one stop shopping. For custom solutions please provide drawing. The factory will quote based on those. llow adequate time for first delivery. Polycarbonate / Polystyrene Explosion Proof Functional Integrity No Minimum Orders! Our service makes the difference! Offshore pplications Stainless Steel & Powder-coated Steel ccessories: Extension Frames, Mounting Plates, IN Rails, Flanges, Screws, etc Gray or Transparent Covers EMI Proof Polycarbonate Request Your Catalog Today: / info@sealconusa.com Large variety of Sizes! 51 ccessories dapter,reducer,enlarger

52 Nickel Plated rass Nylon Strain Relief Other Products Strain Relief Fittings for azardous Locations Strain Relief Fittings in all popular thread types and sizes for standard applications in hazardous location according to EN 50014, EN and EN Machine, apparatus and plant equipment Measuring control and feedback systems Control cabinets Railroad cars and vehicles Industrial installations Marine Off-shore and in all installations where excellent performance, fire resistance and no twisting or torquing of the cable are critical. ccessories dapter,reducer,enlarger 52 TEX TEX 95 equipment directive 94/9/EC, Equipment and protective systems intended for use in potentially explosive atmospheres. TEX gets its name from the French title of the 94/9/EC directive: ppareils destinés à être utilisés en Tmosphères EXplosibles The regulations apply to all equipment intended for use in explosive atmospheres, electrical or mechanical, including protective systems. There are two categories of equipment I for coal mining and II for industrial applications. Once certified, the equipment is marked by the CE (meaning it complies with TEX and all other relevant directives) and Ex symbol to identify it as approved under the TEX directive. Ex-d = Flameproof Ex-e = Increased Safety Class I iv II Cable glands currently under development E1F 2 E1F - disassembled These Cable Glands will be available: 2 Cable Glands for non-armored cables, Ex-e applications C Cable Glands for armored cables, Ex-e applications 2F Cable Glands for non-armored cables in hazardous (combustible) Ex-d environments E1F Cable Glands for armored cable with dual seal in hazardous (combustible) Ex-d environments Most of our standard Strain Relief Fittings are available with EX / TEX approvals. For more information, please visit our website: or call our Customer Service for assistance:

53 Sealcon Fax: Name Company Your company is best classified as: Faxback Form Title iv./ms ddress City State Phone ( ) Fax ( ) Sealcon info@sealconusa.com Nickel Plated rass Nylon Strain Relief OEM End User / MRO Systems Integrator Your primary job function: istributor Contractor Government / School Consultant Other: Product esign System esign Plant Operations/Maintenance Sales / Marketing Purchasing Other: Which industry(ies) does your company serve? (Please check all that apply) musement ntennas utomobile Parts & Supplies Cable ouses Car Wash Chemical Manufacturing Commercial ir Conditioning Computer Construction & uildings Consulting & Eng. Services Education & Consultant Electric Equipment Electric Manufacturing Electronic Equipment Farm Equipment Food Processing Catalogs & Flyers Request: Sealcon Strain Relief Fittings & ccessories Circular Connectors Catalog Industrial Enclosures Catalog European & omestic Cable Catalog Request for Quote/Samples: Part Number(s) Cable O.. Quantity pplication Comments Other Cable Management Needs (Sales will Call to Verify Sample) Furnaces ardware Wholesale ot Tubs & Spas Ice Making Equipment Industrial Measurement Irrigation Laboratory Equipment Lighting Machine Tool Manufacturers Manufacturers Marine Material andling Equipment Medical Equipment Military Mining Equipment Molding Plastic Maintenance / Repair Packaging Machinery Printing Equipment Pumps Research & evelopment Recreational Vehicles Solar Panels / Solar Power Systems Steam Cleaning & rying Swimming Pools Telephone / Telecom Equipment Trailer / Trucking Transportation Utility & Other Energy Systems Water Treatment Wind Power Systems Wood Processing Other: Circular Connector Flyer M23 RJ45 - Industrial Ethernet Flyer dapter, Reducer & Enlarger Flyer ensel - Industrial Enclosures Flyer Complete form & fax back to Our Inside Technical Sales will process your requests in the order they were received. 53 ccessories dapter,reducer,enlarger

54 Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger 54 Sealcon Part Numbers ummel Part Numbers ummel escription Sealcon Page Nr. F-xxxx-K / E-M-P / R-M-P 35 F-xxxx-R RE-Ms 34 G-xxxx-K G-xxxx-R /-L RE-Ms 34 M-xxxx-K M-xxxx-R RE-Ms 34 N-xxxx-R P-xxxx-K / E-M-P / R-M-P 35 P-xxxx-R RE-Ms 34 T-xxxx-R Cxx-E SK-M-EMV 20 Cxx-K /-GY SK-K 4 Cxx--R SK-M 14 Cxx-CP SK-K-MZ 9 Cxx-FE SK-M-EMV- 21 Cxx-MZ SK-MZ 17 Cxx-RV SK-M-PVF 26 Cxx-SS SK-INOX 27 Cxx-SV SK-INOX-PVF 27 Cxx-TE SK-K-PVF 25 CxxP-K /-GY SK-K-Multi 10 CxxP-R SK-M-Multi 22 CxxR-E SK-M-EMV 20 CxxR-K /-GY SK-K 4 Cxx-R-R SK-M 14 CxxR-RV SK-M-PVF 26 CxxR-SS SK-INOX 27 CxxR-SV SK-INOX-PVF 27 CxxR-TE SK-K-PVF 25 CxxS-01 / SK-K-FLK 9 CxxW-R SK-MINI-M 15 Cxxx-K /-GY SK-K-Multi 10 Cxxx-R SK-M-Multi 22 Cxx-K /-GY SK-KR 7 CxxR-K /-GY SK-KR 7 CxxC-E SK-M-EMV 20 CxxC-K /-GY SK-K 6 Cxx-C-R SK-M 16 CxxC-FE SK-M-EMV- 21 CxxC-MZ SK-MZ 17 CxxC-RV SK-M-PVF 26 CxxCR-E SK-M-EMV 20 CxxCR-K /-GY SK-K 6 Cxx-CR-R SK-M 16 CxxCR-RV SK-M-PVF 26 Cxx-E SK-M-EMV 20 Cxx-K /-GY SK-K 6 Cxx--R SK-M 16 Cxx-FE SK-M-EMV- 21 Cxx-MZ SK-MZ 17 Cxx-RV SK-M-PVF 26 CxxR-E SK-M-EMV 20 CxxR-K /-GY SK-K 6 Cxx-R-R SK-M 16 CxxR-MZ SK-MZ 17 CxxR-RV SK-M-PVF 26 CxxG-K /-GY SK-KE 7 CxxGR-K /-GY SK-KE 7 Cxx-L-K /-GY SK-K 4 CxxLP-K /-GY SK-K-Multi 11 CxxLP-R SK-M-Multi 23 Cxx-LR-K /-GY SK-K 4 CxxLx-K /-GY SK-K-Multi 11 CxxLx-R SK-M-Multi 23 CxxM-E SK-M-EMV 20 CxxM-K /-GY SK-K 5 Index / Cross Reference Sealcon Part Numbers ummel Part Numbers ummel escription Sealcon Page Nr. Cxx-M-R SK-M 14 CxxM-CP SK-K-MZ 9 CxxM-FE SK-M-EMV- 21 CxxM-MZ SK-MZ 17 CxxM-RV SK-M-PVF 26 CxxM-SS SK-INOX 27 CxxM-SV SK-INOX-PVF 27 CxxM-TE SK-K-PVF 25 CxxMP-K /-GY SK-K-Multi 12 CxxMP-R SK-M-Multi 24 CxxMR-E SK-M-EMV 20 CxxMR-K /-GY SK-K 5 Cxx-MR-R SK-M 14 CxxMR-MZ SK-MZ 17 CxxMR-RV SK-M-PVF 26 CxxMR-SS SK-INOX 27 CxxMR-SV SK-INOX-PVF 27 CxxMR-TE SK-K-PVF 25 CxxMS-01 / SK-K-FLK 9 CxxMW-R /-RV SK-MINI-M 15 CxxMx-K /-GY SK-K-Multi 12 CxxMx-R SK-M-Multi 24 CxxN-E SK-M-EMV 20 CxxN-K /-GY SK-K 4 Cxx-N-R SK-M 14 CxxN-FE SK-M-EMV- 21 CxxN-MZ SK-MZ 17 CxxN-RV SK-M-PVF 26 CxxN-SS SK-INOX 27 CxxN-SV SK-INOX 27 CxxN-TE SK-K-PVF 25 CxxNP-K /-GY SK-K-Multi 11 CxxNP-R SK-M-Multi 23 CxxNR-E SK-M-EMV 20 CxxNR-K /-GY SK-K 4 Cxx-NR-R SK-M 14 CxxNR-RV SK-M-PVF 26 CxxNR-SS SK-INOX 27 CxxNR-SV SK-INOX 27 CxxNR-TE SK-K-PVF 25 CxxNS-01 / SK-K-FLK 9 CxxNx-K /-GY SK-K-Multi 11 CxxNx-R SK-M-Multi 23 CFxx-E SK-M-Flex-EMV 20 CFxx-K /-GY / SK-Flex 4 CFxx--R SK-M-Flex 14 CFxx-TE - needs to be built 25 CFxxP-R - needs to be built 22 CFxxR-E SK-M-Flex-EMV 20 CFxxR-K /-GY / SK-Flex 4 CFxx-R-R SK-M-Flex 14 CFxxR-TE - needs to be built 25 CFxxx-R - needs to be built 22 CFxx-K /-GY SK-KR-Flex 7 CFxxR-K /-GY SK-KR-Flex 7 CFxxC-E SK-M-Flex-EMV 20 CFxxC-K /-GY / SK-Flex 6 CFxx-C-R SK-M-Flex 16 CFxxCR-E SK-M-Flex-EMV 20 CFxxCR-K /-GY / SK-Flex 6 CFxx-CR-R SK-M-Flex 16 CFxx-E SK-M-Flex-EMV 20 CFxx-K /-GY / SK-Flex 6 CFxx--R SK-M-Flex 16 CFxxR-E SK-M-Flex-EMV 20 CFxxR-K /-GY / SK-Flex 6

55 Sealcon Part Numbers ummel Part Numbers ummel escription Sealcon Page Nr. CFxx-R-R SK-M-Flex 16 CFxxG-K /-GY SK-KE-Flex 7 CFxxGR-K /-GY SK-KE-Flex 7 CFxxM-E SK-M-Flex-EMV 20 CFxxM-K /-GY / SK-Flex 5 CFxx-M-R SK-M-Flex 14 CFxxM-TE - needs to be built 25 CFxxMP-R - needs to be built 24 CFxxMR-E SK-M-Flex-EMV 20 CFxxMR-K /-GY / SK-Flex 5 CFxx-MR-R SK-M-Flex 14 CFxxMR-TE - needs to be built 25 CFxxMx-R - needs to be built 24 CFxxN-K /-GY / SK-Flex 4 CFxx-N-R SK-M-Flex 14 CFxxN-TE - needs to be built 25 CFxxNP-R - needs to be built 23 CFxxNR-K /-GY / SK-Flex 4 CFxx-NR-R SK-M-Flex 14 CFxxNR-TE - needs to be built 25 CFxxNx-R - needs to be built 23 CXxxGx-R SK-XL 15 CXxxMx-R SK-XL 15 M-xx-K /-GY V-N-FS 31 M-xx-R V-N-Ms 31 M-xx-R V-N-Ms-S 31 P-xx-K /-GY V-N-FS 31 P-xx-R V-N-Ms 31 P-xx-R V-N-Ms-S 31 Sxx-K SK-E 44 SxxM-K SK-E 44 SxxN-K SK-E 44 UOxx-K Snapclic-UO-P 43 UOxx-R Snapclic-UO-Ms 43 UOxxR-K Snapclic-UO-P 43 UOxxR-R Snapclic-UO-Ms 43 UOxxM-K Snapclic-UO-P 43 UOxxM-R Snapclic-UO-Ms 43 UOxxMR-K Snapclic-UO-P 43 UOxxMR-R Snapclic-UO-Ms 43 Exx-K /-GY SK-W 8 Exx-R SK-M-W 17 ExxR-K /-GY SK-W 8 ExxR-R SK-M-W 17 ExxF-R SK-M-W 17 ExxFR-R SK-M-W 17 ExxM-K /-GY SK-W 8 ExxM-R SK-M-W 17 ExxMR-K /-GY SK-W 8 ExxMR-R SK-M-W 17 ExxN-K /-GY SK-W 8 ExxNR-K /-GY SK-W 8 EFxx-K /-GY SK-W-Flex 8 EFxxR-K /-GY SK-W-Flex 8 EFxxM-K /-GY SK-W-Flex 8 EFxxMR-K /-GY SK-W-Flex 8 EFxxN-K /-GY SK-W-Flex 8 EFxxNR-K /-GY SK-W-Flex 8 EMxx-K SM-W 41 EMxxM-K SM-W 41 EMxxN-K SM-W 41 EM-xxxx-K E-M-P 39 EM-xxxx-R E-Ms 39 EN-xxxx-R EP-xxxx-R E-Ms 39 ETxx-K E-W 42 Index / Cross Reference Sealcon Part Numbers ummel Part Numbers ummel escription Sealcon Page Nr. ETxxN-K E-W 42 FL-xx-K KF-G 44 FT-xx-K KF-W 44 M-xx-K V-NE 31 M-xx-R V-NE-Ms 31 M-xx-R V-NE-Ms-S 31 M-xx-R-V V-NE-Ms-FPM 31 M-xx-SS V-INOX 32 M-xx-SS-S V-INOX 32 M-xx-SS-V V-INOX 32 N-xx-K P-xx-K V-NE 31 P-xx-R V-NE-Ms 31 P-xx-R V-NE-Ms-S 31 P-xx-R-V V-NE-Ms-FPM 31 P-xx-SS V-INOX 32 P-xx-SS-S V-INOX 32 P-xx-SS-V V-INOX 32 KLxx-R KLE 32 KLxxM-R KLE 32 M-xx-K U 40 NG-xx-XL GM-Ms (XL) 15 NM-xx-E GM-EMV 29 NM-xx-K /-GY GM-FS 29 NM-xx-R GM-Ms 29 NM-xx-XL GM-Ms (XL) 15 NN-xx-E NN-xx-K /-GY GM-FS 29 NN-xx-R GM-Ms 29 NN-xx-ST NP-xx-E GM-EMV 29 NP-xx-K /-GY GM-FS 29 NP-xx-R GM-Ms 29 OM-xx-N /-VT O-Ring 30 OM-xx-SI O-Ring - Silicone 30 OR-xx-N /-VT O-Ring 30 OR-xx-SI O-Ring - Silicone 30 PL-xx-K SK-V 30 R-0x RS 32 R-xxxx RM-xxxx-K R-M-P 37 RM-xxxx-R RS-Ms 36 RM-xxxx-SS RS-INOX 38 RM-xxxx-SS RS-INOX 38 RM-xxxx-SS-S on request RS-INOX 38 RM-xxxx-SS-V on request RS-INOX 38 RN-xxxx-R RP-xxxx-R RS-Ms 36 RP-xxxx-SS RS-INOX 38 RQ-xxxx-R RS-Ms 36 RQ-xxxx-SS RS-INOX 38 RQ-xxxx-SS-S on request RS-INOX 38 RQ-xxxx-SS-V on request RS-INOX 38 RR-xxxx-R / R- 36 RR-xxxx-GY / R-FS 37 R-xxxx-WR RS 33 SMxx-K SM-N 41 SMxxM-K SM-N 41 SMxxN-K SM-N 41 SM-xx-NY / Seal Rings 30 SM-xxxx-K SM-WS-P 40 SM-xxxx-Y E-Y 40 SR-xx-NY / Seal Rings 30 STxx-K E 42 STxxN-K E 42 S-xxxx-WR ST Nickel Plated rass Nylon Strain Relief ccessories dapter,reducer,enlarger

56 We Provide Customers with Cable Management Solutions! 2/3 C rawing for Viewing Specs! Most of our standard Strain Relief and Conduit Fittings are now available for C download. The links for each download can be found on the detailed product pages of our website. To start C download: 1. Find part number you are interested in based on your 2. Click on P/N that appears in blue hyperlinked text 3. new window will open, choose from the following download options: 3 ownload: IGES, STEP, SOLIWORKS, ST, PRSOLI 2 ownload: SLRW, PF, WG, XF If we do not have the C model you are looking for, please feel free to contact our Inside Technical Sales for assistance. We ll be happy to obtain the C model for you if possible. Other catalogs & flyers available. Call for details... Further information on the products presented here and everything else Sealcon has to offer can be found on our website: Our website is consistently updated. Sealcon Catalogs are also available for download online E. insdale ve. Centennial, CO US Toll Free: / Fax: info@sealconusa.com Web: