Anchor size M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20. Anchor size M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20. Concrete Capacity Method

Transcription

1 HSA tud anhor Feature: - high loading apaity - ore-ontrolled expanion - long thread HSA / HSA-R / HSA-F - head marking or identiiation ater etting - iretop aement - pre-aembled with nut and waher time aving Material: - old ormed HSA: - arbon teel, zin plated to. 5 µm HSA-R: - tainle teel, A4 grade; HSA-F: - arbon teel, hot dipped galvanied to.35 µm (M6-M16) and to. 45µm (M20) Conrete Small edge ditane / paing Fire reitane Hilti Anhor programme A4 316 Corroion reitane Bai loading data (or a ingle anhor): HSA All data on thi page applie to For detailed deign method, ee page onrete: a peiied in the table no edge ditane and paing inluene orret etting (See etting operation page 96) teel ailure non-raked onrete Mean ultimate reitane, R u,m [kn]: onrete C20/25 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Ru,m Shear, V Ru,m Charateriti reitane, R k [kn]: onrete C20/25 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Rk Shear, V Rk Following value aording to the Conrete Capaity Method Deign reitane, R d [kn]: onrete, k,ube = 25 N/mm 2 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Rd Shear, V Rd Reommended load, L re [kn]: onrete, k,ube = 25 N/mm 2 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Re Shear, V Re Iue 2005a 92

2 HSA tud anhor Bai loading data (or a ingle anhor): HSA-R All data on thi etion applie to For detailed deign method, ee page onrete: a peiied in the table no edge ditane and paing inluene orret etting (See etting operation page 96) teel ailure non-raked onrete Mean ultimate reitane, R u,m [kn]: onrete C20/25 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Ru,m Shear, V Ru,m Charateriti reitane, R k [kn]: onrete C20/25 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Rk Shear, V Rk Following value aording to the Conrete Capaity Method Deign reitane, R d [kn]: onrete, k,ube = 25 N/mm 2 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Rd Shear, V Rd Reommended load, L re [kn]: onrete k,ube = 25 N/mm 2 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N re Shear, V re Iue 2005a

3 HSA tud anhor Bai loading data (or a ingle anhor): HSA-F All data on thi page applie to For detailed deign method, ee page onrete: a peiied in the table no edge ditane and paing inluene orret etting (See etting operation page 96) teel ailure non-raked onrete Mean ultimate reitane, R u,m [kn]: onrete C20/25 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Ru,m Shear, V Ru,m Charateriti reitane, R k [kn]: onrete C20/25 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Rk Shear, V Rk Following value aording to the Conrete Capaity Method Deign reitane, R d [kn]: onrete, k,ube = 25 N/mm 2 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Rd Shear, V Rd Reommended load, L re [kn]: onrete, k,ube = 25 N/mm 2 Anhor ize M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20 Standard anhorage depth Redued anhorage depth Tenile, N Re Shear, V Re Iue 2005a 94

4 HSA tud anhor Setting detail HSA tandard anhorage depth HSA redued anhorage depth irt mark: blue ring eond mark: thread end Marking d 0 d T int Head marking h h 1 h e t ix tandard embedment redued embedment Anhor ize M6x50 M6x65 M6x85 M6x100 Setting Detail HSA-R available: OK OK OK OK OK OK OK OK OK OK HSA-F available: OK OK OK OK OK OK OK OK OK OK d o [mm] Noal dia. o drill bit I [mm] Anhor length Head Marking (letter ode) A C D E B C E G H C E F G I I G [mm] Thread length T int [Nm] Torque moment* SW [mm] Width aro nut lat d [mm] Clearane hole diameter h 1 [mm]. depth o drill hole h e [mm] eetive embed. depth h nom [mm]. embedment depth t ix [mm] max. atenable thikne h [mm]. onrete thikne h 1 [mm]. depth o drill hole h e [mm] eetive embed. depth h nom [mm]. embedment depth t ix [mm] max. atenable thikne h [mm]. onrete thikne Required drill bit TE-CX-6 TE-CX-8 TE-CX-10 M8x57 M8x75 M8x92 M8x115 M8x137 M10x68 M10x90 M10x108 M10x120 M10x Iue 2005a

5 HSA tud anhor Setting Detail Anhor ize M12x80 M12x100 M12x120 M12x150 M12x180 M12x220 M12x240 M12x300 M16x100 M16x120 M16x140 M16x190 M16x240 M20x125 M20x170 tandard embedment redued embedment HSA-R available: OK OK OK OK OK OK OK OK HSA-F available: OK OK OK OK OK OK OK OK OK d o [mm] Noal dia. o drill bit I [mm] Anhor length Head Marking (letter ode) D E G I L O P S E G I L P G K I G [mm] Thread length ) T int [Nm] Tightening torque* SW [mm] Width aro nut lat d [mm] Clearane hole diameter h 1 [mm]. depth o drill hole h e [mm] eetive embed. depth h nom [mm]. embedment depth t ix [mm] max. atenable thikne h [mm]. onrete thikne h 1 [mm]. depth o drill hole h e [mm] eetive embed. depth h nom [mm]. embedment depth t ix [mm] max. atenable thikne h [mm]. onrete thikne Required drill bit TE-CX-12 TE-C-16 or TE-Y-16 * pleae note that the torque moment i the ame or tandard and redued embedment 1) thread length o HSA-R: 80 mm Intallation equipment TEC-S 20 TE-Y 20 Rotary hammer (TE1, TE 2, TE5, TE6, TE6A, TE15, TE15-C, TE18-M, TE 35, TE 55, TE 76), drill bit, blow-out pump, torque wrenh and hexagon drive oket appropriately ized or orret etting. Setting operation Drill hole with drill bit. Blow out dut and ragment. Intall anhor. Apply tightening torque. Mehanial propertie o the anhor bolt Anhor ize HSA M6 M8 M10 M12 M16 M20 A [mm 2 ] Streed ro-etion in thread uk [N/ mm 2 ] Noal tenile trength in thread A,i [mm 2 ] Streed ro-etion in taper tranition uk [N/ mm 2 ] Noal tenile trength o taper tranition W el [mm 3 ] Elati moment o reitane M Rd, [Nm] Deign bending moment 1) Iue 2005a 96

6 HSA tud anhor Anhor ize HSA-R M6 M8 M10 M12 M16 M20 A [mm 2 ] Streed ro-etion in thread uk [N/ mm 2 ] Noal tenile trength o thread A,i [mm 2 ] Streed ro-etion in taper tranition uk [N/ mm 2 ] Noal tenile trength o taper tranition W el [mm 3 ] Elati moment o reitane M Rd, [Nm] Deign bending moment 1) Anhor ize HSA-F M6 M8 M10 M12 M16 M20 A [mm 2 ] Streed ro-etion in thread uk [N/ mm 2 ] Noal tenile trength o thread A,i [mm 2 ] Streed ro-etion in taper tranition uk [N/ mm 2 ] Noal tenile trength o taper tranition W el [mm 3 ] Elati moment o reitane M Rd, [Nm] Deign bending moment 1) ) The deign bending moment i alulated rom M Rd, = 1.2 W el uk /γ M where the partial aety ator γ M varie with anhor type and ize. Detailed deign method - Hilti CC ( The Hilti CC method i a impliied verion o ETAG Annex C.) TENSION The tenile deign reitane o a ingle anhor i the lower o N Rd,p : onrete pull-out reitane N Rd, : onrete one reitane N Rd, : teel reitane h N re,p// N Rd,p : Pull-out reitane N Rd, p = N o Rd,p,ta./red. BN N 0 Rd,p,ta./red.: Deign pull-out reitane Conrete ompreive trength, k,ube(150) = 25 N/mm 2 Anhor ize HSA M6 M8 M10 M12 M16 M20 N 0 Rd,p,ta. [kn] Standard anhorage depth ** -** N 0 Rd,p,red. [kn] Redued anhorage depth 2.8* 6.0* 8.0 -** -** -** Anhor ize HSA-R M6 M8 M10 M12 M16 M20 N 0 Rd,p,ta. [kn] Standard anhorage depth N 0 Rd,p,red. [kn] Redued anhorage depth * 5.7 -** Anhor ize HSA-F M6 M8 M10 M12 M16 M20 N 0 Rd,p,ta. [kn] Standard anhorage depth ** -** N 0 Rd,p,red. [kn] Redued anhorage depth 2.8* 6.0* 8.0 -** -** -** The tenile deign reitane i alulated rom the tenile harateriti reitane N o Rk,p by N o Rd,p= N o Rk,p/γ Mp where the partial aety ator varie γ Mp varie with anhor type and ize (a per relevant approval). *Ue i retrited to anhoring o trutural omponent whih are tatially indeterate. ** Pull-out i not deiive or the deign. 97 Iue 2005a

7 N Rd, : Conrete one reitane HSA tud anhor NRd, o = NRd,,ta./ red. T BN AN,ta./ red. RN,ta./ red. N 0 Rd,,ta./red.: Deign onrete one reitane onrete ompreive trength, k,ube(150) = 25 N/mm 2 Anhor ize HSA M6 M8 M10 M12 M16 M20 N 0 Rd,,ta. [kn] Standard anhorage depth N 0 Rd,,red. [kn] Redued anhorage depth 4.6* 7.0* Anhor ize HSA-R M6 M8 M10 M12 M16 M20 N 0 Rd,,ta. [kn] Standard anhorage depth N 0 Rd,,red. [kn] Redued anhorage depth * Anhor ize HSA-F M6 M8 M10 M12 M16 M20 N 0 Rd,,ta. [kn] Standard anhorage depth N 0 Rd,,red. [kn] Redued anhorage depth 4.6* 7.0* The tenile deign reitane i alulated rom the tenile harateriti reitane N o Rk, by N o Rd,= N o Rk,/γ M,N where the partial aety ator varie γ M,N varie with anhor type and ize (a per relevant approval). *Ue i retrited to anhoring o trutural omponent whih are tatially indeterate. T : Inluene o anhorage depth T h h at. e,red. 1.5 = Limit: h e,red. h at. h e,ta. BN : Inluene o onrete trength Conrete trength deignation (ENV 206) Cylinder ompreive trength, k,yl [N/mm²] Cube ompreive trength, k,ube [N/mm²] C20/ C30/ C40/ C50/ AN,ta. : Inluene o anhor paing on tandard anhorage depth Anhor paing, HSA, HSA-R, HSA-F [mm] M6 M8 M10 M12 M16 M B AN,ta. or HSA and HSA-F 0.4,ube BN = 25 Limit: 25N/mm 2 k,ube 60N/mm 2 Limit: or HSA-R BN =1 = h r,n r, N = 3 h e,ta. e,ta. Iue 2005a 98

8 HSA tud anhor AN,red. : Inluene o anhor paing on redued anhorage depth Anhor paing, HSA, HSA-R, HSA-F [mm] M6 M8 M10 M12 M16 M AN,red. Limit: = h r,n r, N = 3 h e,ta e red. RN,ta. : Inluene o edge ditane on tandard anhorage depth Edge ditane, HSA, HSA-R, HSA-F [mm] M6 M8 M10 M12 M16 M RN,red. : Inluene o edge ditane on redued anhorage depth R,N =1.0 RN,ta. Limit: = h r,n = 1.5 h e,ta. r,n e,ta. Note: I more than 3 edge are maller than r, onult the Hilti tehnial adviory ervie. Anhor ize HSA, HSA-F M6 M8 M10 M12 M16 M20 Standard eetive [mm] Min. paing anhorage depth, h e,ta. [mm] Min. edge ditane Redued eetive [mm] Min. paing anhorage depth, h e,red. [mm] Min. edge ditane Anhor ize HSA-R M6 M8 M10 M12 M16 M20 Standard eetive [mm] Min. paing anhorage depth, h e,ta. [mm] Min. edge ditane Redued eetive [mm] Min. paing anhorage depth, h e,red. [mm] Min. edge ditane Iue 2005a

9 HSA tud anhor N Rd, : Steel deign tenile reitane Anhor ize M6 M8 M10 M12 M16 M20 N Rd, [kn] HSA N Rd, [kn] HSA-R N Rd, [kn] HSA-F The deign tenile reitane i alulated rom the harateriti tenile reitane, N Rk,, uing N Rd, = N Rk, /γ M, where the partial aety ator varie γ M varie with anhor type and ize (a per relevant approval). N Rd : Sytem deign tenile reitane N Rd = lower o N Rd,p, N Rd, and N Rd, Combined loading: Only i tenile load and hear load applied (See page 31 and etion 4 Example ). Detailed deign method Hilti CC (The Hilti CC method i a impliied verion o ETAG Annex C.) >1.5 2 V re,/ >1.5 2 SHEAR h>1.5 The deign hear reitane o a ingle anhor i the lower o V Rd, : onrete edge reitane V Rd, : teel reitane Note: I the ondition or h and 2 are not met, onult your Hilti tehnial adviory ervie. V Rd, : Conrete edge deign reitane The lowet onrete edge reitane mut be alulated. All near edge mut be heked, (not only the edge in the diretion o hear). The diretion o hear i aounted or by the ator β,v. V Rd, o = VRd,,ta. / red. B β,v AR,V V 0 Rd,,ta./red. : Conrete edge deign reitane Conrete ompreive trength, k,ube(150) = 25 N/mm 2 at imum edge ditane Anhor ize HSA M6 M8 M10 M12 M16 M20 V 0 Rd,,ta. [kn] Standard anhorage depth V 0 Rd,,red. [kn] Redued anhorage depth 2.2* 2.4* Iue 2005a 100

10 HSA tud anhor Anhor ize HSA-R M6 M8 M10 M12 M16 M20 V 0 Rd,,ta. [kn] Standard anhorage depth V 0 Rd,,red. [kn] Redued anhorage depth * Anhor ize HSA-F M6 M8 M10 M12 M16 M20 V 0 Rd,,ta. [kn] Standard anhorage depth V 0 Rd,,red. [kn] Redued anhorage depth 2.2* 2.4* The hear deign reitane i alulated rom the hear harateriti reitane V o Rk, by V o Rd,= V o Rk,/γ M,V, where the partial aety ator γ M,V i equal to 1.5. *Ue i retrited to anhoring o trutural omponent whih are tatially indeterate. B : Inluene o onrete trength Conrete trength deignation (ENV 206) Cylinder ompreive trength, k,yl [N/mm²] Cube ompreive trength, k,ube [N/mm²] C20/ C25/ C30/ C35/ C40/ C45/ C50/ B B = k,ube 25 Limit: 25 N/mm 2 k,ube(150) 60 N/mm 2 Conrete ylinder: Conrete ube: height 30m, 15m ide length 15m diameter Conrete tet peimen geometry β,v : Inluene o hear loading diretion Angle, β [ ] β,v 0 to to Formulae: β, V = 1 1 β, V = o β in β β, V = 2 or 0 β 55 or 55 < β 90 or 90 < β 180 β V... applied hear ore AR,V : Inluene o edge ditane and paing Formula or ingle-anhor atening inluened only by edge = AR,V Formula or two-anhor atening valid or < 3 AR,V 3 + = 6 reult tabulated below 2,1 n ,2 h >1,5 General ormula or n-anhor atening (edge plu n-1 paing) only valid where 1 to n-1 are all < 3 and 2 > 1.5. AR,V 3 + = n n 1 Note: It i aumed that only the row o anhor loet to the ree onrete edge arrie the entri hear load. 101 Iue 2005a

11 HSA tud anhor AR.V / Single anhor with edge inluene, / Thee reult are or a two Anhor atening For atening made with more than 2 anhor, ue the general ormulae or n anhor the page beore V Rd, : Steel deign hear reitane Anhor ize M6 M8 M10 M12 M16 M20 V Rd, [KN] HSA Anhor ize M6 M8 M10 M12 M16 M20 V Rd, [KN] HSA-R Anhor ize M6 M8 M10 M12 M16 M20 V Rd, [KN] HSA-F The deign hear reitane i alulated rom the harateriti hear reitane, V Rk,, uing V Rd, = V Rk, /γ M, where the partial aety ator varie γ M varie with anhor type and ize (a per relevant approval). V Rd : Sytem deign hear reitane V Rd = lower o V Rd,,ta./red. and V Rd, Combined loading: Only i tenile load and hear load applied (See page 31 and etion 4 Example ). 102