The Ins and Outs of Trombone Hand Slide Repair. Trevor Roberts Twin Village Music
|
|
|
- Meghan Horn
- 5 years ago
- Views:
Transcription
1 The Ins and Outs of Trombone Hand Slide Repair Trevor Roberts Twin Village Music
2 Why do people shy away from hand slides? - They are "hard"? - There is a Stigma about them? -They put up a fight? - Trombone players are impossible to please? - Why do you feel angst for them...
3 New Does Not Mean Correct Manufacturer #1 Hand slide #1: - Top: Middle: Bottom: Hand slide 2: - Top: Middle: Bottom: Hand slide 3: - Top: Middle: Bottom: Manufacturer #2 Hand Slide #1: - Top: Middle: Bottom: Hand Slide #2: - Top: Middle: Bottom: Hand Slide #3: - Top: Middle: Bottom: 3.519
4 Inspection Does it move? How does it move Are tubes straight Dents (crook, outer tube, inner tube) Solder joints Other damage (bracing, red rot) Do the inner slides come out like a tuning fork How parallel are the tubes Take measurements
5 Measure and Write it Down Measure with digital calipers that go down to.0005 (WIHA DigiMax #41101 carbon plastic) Measure below outer stockings, above crook, and middle of tube Measure above and below hand slide brace on outer stockings
6 Cleaning Ultrasonic cleaning Texas flush Power Brass for stubborn buildup The "evil" Flex Hone Omega Horn Clean 727 ultrasonic solution Tesch Power Brass (Votaw part number 3612)
7 Disassembly and Dent Work Remove Crook - Does it spring in any direction? Get the upper outer stockings close to parallel Separate slide tubes Remove dents in crook and slide tubes Make sure slide tubes are round Votaw trombone hand slide mandrel set (2085 Full set) Your preferred dent hammers Red Wing "Nose Picker" Ferrees hand slide roller (N87A) "C" Burnisher Ferrees P1 Roller *Carefully* J.L. Smith internal burnisher ( tenor, Bass)
8 Damage Before and After
9 Damage Before and After
10 Importance of the Hand Slide Crook
11 Importance of the Hand Slide Crook Damage to crook will always throw off your parallel "Don't worry about the dents, just fix the hand slide..." THIS IS WHY IT MATTERS:
12 Straightening Slide Tubes OUTSIDE SLIDE: Sight perpendicular to light source to see bends Make correction Check visually, and with a known flat object (Ferrees P89) Check with inner tube once both are straight INSIDE SLIDE: Sight perpendicular to light source to see bends (especially near stockings) Make correction Check visually, and with a known flat object
13 Ferrees P89
14 Double Check Everything! BE PATIENT Metal memory can throw off your slide tube straightening efforts Make any corrections you may need Did you miss anything Do all inner and outer tubes run smoothly in all 360 degrees Now You are ready to assemble...
15 Make sure slide tubes fit together well (cleaned up solder, no flared ends etc) Make sure tubes are flat to the steels Begin measuring (top, mid, bottom, outer stockings) Assembly on the P90
16 Assembly on the P90 Once measurements are within spec from top to bottom (within.001 or better.0005) it is time to begin soldering. Solder hand slide crook on fixed side of hand slide (side that has the majority of the hand slide brace) and let cool completely Great time to Multitask (rental clarinets etc... Measure everything again!!! Solder hand slide brace and let cool completely Measure everything again!!! Solder other side of hand slide crook Solder inner slide tube hand slide brace to match dimensions of rebuilt outer slide
17 Keep Solder Joints Clean with No Excess
18 Final Steps Clean again Have I mentioned measuring? Check tubes still run individually Check both tubes together vertically, 45 degrees, and minimal angle Final polish of tubes, and clean up with alcohol Check action again Clean up lacquer and minor tinning from assembly (spot lacquer if needed)
19 Other Random Hand slide stuff King hand slides with press fit "anti solder rattle" bushings They will shoot out if overheated "ask younger me how I know" Small drill bit puncture to relieve pressure
20 Other Random Hand slide stuff
21 Other Random Hand slide stuff
22 THANK YOU FOR YOUR TIME AND ATTENTION. QUESTIONS?
AVA Building Instructions
Suggested Assembly Sequence: AVA Building Instructions 1. Insert fittings in rudder and trial fit rudder on boom 2. Attach stab to v-mount and position ahead of rudder ¼, sanding the v-mount as needed.
MICRO - DLG. This kit should only take 30 minutes to compile, very simple and quick.
MICRO - DLG This kit should only take 30 minutes to compile, very simple and quick. You will need: Hot Glue ( small tip preferably ) Sharp razor blade Ruler a strip of strong fiber tape Thin nose Pliers
QRPGuys Single Lever Mini Paddle
QRPGuys Single Lever Mini Paddle First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
Parts List. 7. Handlebars 8. Grips 9. Handlebar Stem 10. Front Brake 11. Front Wheel 12. Crank 13. Chain
Woodworm Cruise Parts List 1. Free Wheel with Rear Hub 2. Fenders 3. Fender Stay 4. Quick Release 5. Saddle 6. Seat Post 7. Handlebars 8. Grips 9. Handlebar Stem 10. Front Brake 11. Front Wheel 12. Crank
Exxtacy. Repair and Tuning Manual. Exxtacy Construction Basics
1 of 20 Exxtacy Repair and Tuning Manual Construction Basics D Cell Repair Rib Repair Tuning Exxtacy Construction Basics The Exxtacy is built with carbon fiber and Kevlar/Aramide honeycomb. The Exxtacy
5/16 MAXFLOW SPOUTS 17/64 MAXFLOW SPOUTS. 5/16 black spout with barbs $0.25 $ /64 white spout without barbs. 5/16 white spout without barbs
FITTINGS The new line of 5/16" Maxflow fittings was specifically designed and developed for maple producers wanting to operate over 25 in-hg (high vacuum). These fittings enable a perfect seal with a vacuum
PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro
1980 82 PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro Introduction: The 1980 turbine Pay N Pak is a good subject for a model race boat. It has a low profile, mild pickle-fork setback, long
Installation and Operation Instruction Manual
Installation and Operation Instruction Manual Toggle Lok Anchor - Model #7442 Portable Concrete Anchorage Connector ANSI Z359.1 5,000 lbs / 22.24 kn FallTech, Inc 1306 Alameda Street Compton, CA 90221
Accord 4CYL. Disclaimer: is the first to
Replacing Lower Control Arm Bushings on a 2007 Honda Accord 4CYL Disclaimer: I have benefited greatly from others who have taken the time to post auto repair videos/tutorials online. To try and return
Blazer Marine, Whiplash Sport Hydro
Blazer Marine, Whiplash Sport Hydro Thank you for choosing to build the Whiplash Sport Hydro. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We
CZ52 Detail Strip, Disassembly, and Assembly Instructions Lonestar Fabrication & Design
CZ52 Detail Strip, Disassembly, and Assembly Instructions 2008 Lonestar Fabrication & Design These instructions may be freely distributed and copied providing this page is included, and providing they
FLEXIBLE SHAFTING (Wet & Dry)
TM-5 April 5, 2004 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders tube rolling motors
Horizontal Fuselage. Top Vertical Fuselage 1. Lay out the Top Vertical Fuse Front(1), Top Vertical Fuse Back(2), and Vertical Stabilizer(3).
Rumbuilder 71 B-17 Congrats on your Rumbuilder B-17! We re glad you chose to fly with us! If you have any problems, or missing/broken kit pieces, please contact us. We d be happy to replace any damaged
A Table Top Wind Tunnel You Can Build
A Table Top Wind Tunnel You Can Build Basic principles of aerodynamics can be studied in the classroom with this simple, inexpensive wind tunnel. All you need to build it is some cardboard boxes, glue,
FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions
FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY
Tugster. Tug Boat. Competition or Sport Tug Kit. A Zippkits R/C Boat. Building Instructions
Z I P P M A N U FA C T U R I N G Tugster Tug Boat Competition or Sport Tug Kit A Zippkits R/C Boat Building Instructions 2016 JMP Hobby Group St. Paul, Indiana 47272 www.zippkits.com Toll Free (866) 922-ZIPP
Stromberg Fuel Tee Replacement Michael Hartman Version 1.1 February 14, 2017
Stromberg Fuel Tee Replacement Michael Hartman Version 1.1 February 14, 2017 The plastic fuel tee supplying fuel to the twin Stromberg 150CDs on my Sunbeam Alpine Series V had cracked and was spewing gas
Rudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
INSTALLATION INSTRUCTIONS FOR EXHAUST CUFF MODIFICATION
INSTALLATION INSTRUCTIONS FOR EXHAUST CUFF MODIFICATION Document # PCA1001-22 Revision LTR: A Date: 07/06/09 1 Notes: 1. The cuff must be installed onto the aircraft prior to painting. Once installed the
SCOUT DECK ANCHOR 3 1/4" BONDING SCREW
SCOUT DECK ANCHOR 16" 16" 1" X 4" ANCHOR BOLT (4) 10" 3 1/8" 5" 6" MIN COPPER WIRE TO ATTACH TO BONDING GRID 3 1/4" BONDING SCREW CONCRETE DECK SPECIFICATIONS: THE AQUA CREEK PRODUCTS' SCOUT DECK ANCHOR
Monsoon repair/service helper. To high: Shoot a couple of shots until you get under 210bar, if it is higher than 210bar it will
Monsoon repair/service helper 1. Pressure: Min 180bar Max 210bar To low: Charge with air To high: Shoot a couple of shots until you get under 210bar, if it is higher than 210bar it will Not be able to
Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
Read through all the steps first before working on the camera. Make sure you know what to do.
Step-by-step procedure to fix lack of contact in the end-of-travel switch of a D700 pop-up flash DISCLAIMER: PLEASE UNDERSTAND THAT IF YOU DECIDE TO FOLLOW THE INFORMATION PROVIDED BELOW YOU DO SO AT YOUR
AR-15 Rifle Operator Maintenance
AR-15 Rifle Operator Maintenance These procedures cover how to Clean, Inspect and Lubricate the AR15 Rifle NOTICE: This is not a replacement for the manufacturer s manual. If you do not have the owners
1/10 th Scale 1956 Ted Jones Classic Hydroplane
1/10 th Scale 1956 Ted Jones Classic Hydroplane Preparation These plans show outside sheeting of 3/32 balsa laminated with 1/64 birch ply. This makes a light and strong skin for this boat. Optionally you
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
COMPACT TRIPLE WALL OUTLET STATION MODEL INSTALLATION AND OPERATING INSTRUCTIONS
COMPACT TRIPLE WALL OUTLET STATION MODEL 6255-1 INSTALLATION AND OPERATING INSTRUCTIONS To assure safe operation and conformation to local fire codes, all Porter Outlet Stations are designed to be used
Deluxe Gourd Racks I D E G A. Parts List. Shown above are parts for the two-level, Deluxe Gourd Rack (DGR 12V)with 12 arms for vertically hung gourds.
Deluxe Gourd Racks H F K I D E J C G A Shown above are parts for the two-level, Deluxe Gourd Rack (DGR V)with arms for vertically hung gourds. Parts List Code Quantity A B C D E F G H I J 6, or 4 6, or
Dornier Do R 4 Super-Wal
Dornier Do R 4 Super-Wal Model Aviation Laddie Mikulasko s Dornier Do R 4 Super-Wal Build the multiengine, record-setting seaplane. Article, plans, instructions, and photos by Laddie Mikulasko. Complete
FIX ROAD & FIX STRAP cargo securing systems Operating Instruction Manual
FIX ROAD & FIX STRAP cargo securing systems Operating Instruction Manual NWE NETWORK ENGINEERING OY AB VAT: FI 09628099 1 Introduction Please ensure you read these instructions and understand them fully
Competition Volleyball
ASSEMBLY & OPERATING INSTRUCTIONS INS692 Revision 5 29/0/208 0 mins Only person is required for this assembly Estimated 0 minutes assembly time i IMPORTANT: Read these instructions in their entirety before
Refurbishing TR6 Window Slides. Chuck Hobbs 27 Feb 2017
Refurbishing TR6 Window Slides Chuck Hobbs 27 Feb 2017 Why Refurbish your Window Slides? Original slides are 40+ years old and are usually rusty, have no felt left on the runners and often the windows
A Low Cost Digital Angle Gage, version 3
A Low Cost Digital Angle Gage, version 3 By R. G. Sparber Copyleft protects this document. 1 Sometimes re-inventing the wheel has advantages. What you see here is just a variation on a sine bar. The accuracy
Ground Release Shackle
Operator Manual Subhead Advantages: In the process of installing Slide Rail, the shackle connecting the top of posts, panels, and sheeting must be removed manually. This is normally done by climbing on
Medium Voltage Switchgear. Installation Manual for Pressure Relief Ducts
Uniswitch Medium Voltage Switchgear Installation Manual for Pressure Relief Ducts TABLE OF CONTENTS 1 Summary... 1 2 Transportation and storage... 2 2.1 Condition on delivery... 2 2.2 Unpacking at installation
Assembly Instructions. for. Puffin Saranac. ScanSport, Inc. P.O. Box 700 (234 May Street) Enfield, New Hampshire Phone: (603)
Assembly Instructions for Puffin Saranac ScanSport, Inc. P.O. Box 700 (234 May Street) Enfield, New Hampshire 03748 Phone: (603) 632 9500 Fax: (603) 632 5611 info@pakboats.com www.pakboats.com Assembling
Safety. Lawn Striper Kit CAUTION CAUTION. Operator Manual. Read all of the instructions in this manual prior to
Lawn Striper Kit Form No. 3368-858 Rev A Model No. 20601 Operator Manual Safety Read all of the instructions in this manual prior to using the lawn striper attachment. The lawn striper attaches to and
INSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
WHEATLEY WHEATLEY SERIES 500 SWING CHECK VALVE. Installation, Operation and Maintenance Manual
WHEATLEY SERIES 500 SWING CHECK VALVE STANDARD INTEGRAL SEAT & OPTIONAL REMOVABLE SEAT 2" FP - 6" FP 150# - 1500# 8" FP - 12" FP 150# - 900# API 6D and B16.34 2" FP - 4" FP 5000# DRILLING PRODUCTION VALVE
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles.
Welcome to Huma-Air. We design and manufacture brand- and model specific precision regulators for PCP air rifles. By using only the highest quality materials such as aircraft grade aluminum, aluminumbronze,
Fix Your Swing Series. Table of Contents
Fix Your Swing Series Table of Contents 1. Hit More Fairways 2. Fix Your Setup 3. Fix Your Ball Position 4. Fix Your Takeaway 5. Fix Your Backswing 6. Fix the Top of Your Swing 7. Fix Your Downswing 8.
400/488 Rotating Davit Installation Instructions
400/488 Rotating Davit Installation Instructions These instructions were written with the owner in mind. If you are the installer make sure these instructions are passed along to the owner of the boat.
Parkzone Vapor Repair tutorials
Propeller replacement The propeller is held on by the threaded shaft. You will need to grip the shaft/cog with your fingers or some pliers and rotate the propeller anticlockwise when viewed from the front.
Steps for W17, W14,W07, Wing Assembly Sonex #815
CAUTION: This document is in no way a publication of Sonex Aircraft LLC. or any other corporation. All products mentioned are not necessarily recommended for use, but are included for informational purposes
OPERATIONS CHALLENGE 2017
OPERATIONS CHALLENGE 2017 COLLECTION SYSTEM EVENT During the event, your team will complete the following: The event simulates connecting a 4-inch PVC lateral sewer to an existing 8-inch PVC sewer pipe
Kalibrgun Cricket series Regulated Airspace Increaser (RAI) with gauge, installing instruction by AS
Kalibrgun Cricket series Regulated Airspace Increaser (RAI) with gauge, installing instruction by AS First I must thank you for buying RAI. RAI is designed to use in the Kalibrgun Cricket series and nowhere
Blazer Marine, Whiplash Sport 40
Blazer Marine, Whiplash Sport 40 Thank you for choosing to build the Whiplash 40. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We are excited
Xtender30. Home Batting Cage. Assembly Instructions
Xtender30 Home Batting Cage Assembly Instructions IMPORTANT DO NOT RETURN THIS BATTING CAGE TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 IMPORTANT WARRANTY WARNING: DO NOT LEAVE
Universal Elevator Mount Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A.
REQUIRED TOOLS AND MATERIALS: 2 Capable Adults Carpenter s Level 15 Tape Measure Pencil Universal Elevator Mount Owners Manual Customer Service Center N53 W2400 South Corporate Circle Sussex, WI 530 U.S.A.
- Written price quotations are valid for 30 days from the date of the quote unless otherwise noted.
SPECIFICATIONS - All material is solid brass with a #8 mirror finish unless otherwise noted. - All material sold by length is priced in one foot increments. ORDERING PROCEDURE - Use a Purchase Order number.
Body - May vary in shape, body beads may be present, and is constructed of electrolytic tinplate (ETP).
2 1 2. CAN TERMINOLOGY Any discussion or description of can defects requires standard terminology relating to the can components (end, body, double seam). The terminology required to describe these components
SCUBAPRO Repair Guide. S600-S550 Second Stages
SCUBAPRO Repair Guide S600-S550 Second Stages S600 Configuration A S600 Configuration B USE THIS GUIDE AS A REFERENCE WHEN SERVICING THE S600 AND S550 SECOND STAGES S550 P/N 41-047-000 FOR REPAIR OF S600-S550
RADIUS ROD BUSHING SET
RADIUS ROD BUSHING SET These are designed to allow your front suspension to operate much more freely than the factory units, with less maintenaance. STICKSION could be a key word here. The front end will
Everything you need to know about flatteners and levelers for coil processing
http://www.thefabricator.com/xp/fabricator/articles/fabricating/fabricating03/02web56 9.xml Provided by: Welded Tube Pros LLC, www.weldedtubepros.com Doylestown, OH. Tel: 330-658-7070 Email contact for
The author's TD Coupe, used as a towplane, and the Airhopper. The gas model is equipped with an automatic towline release.
THE AIRHOPPER BY STANLEY ORZECK PLANS BY PAUL PLECAN An eight-foot sailplane either towed by a gas model or launched by hand tow. The author's TD Coupe, used as a towplane, and the Airhopper. The gas model
Model: 5100 OmniSteel Volleyball System
Model: 5100 OmniSteel Volleyball System Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS
Your kit contains the following items. Additional Items You May Need. Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet
Your kit contains the following items Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet The SkyFox offers great glide performance in a rubber powered plane due to its built up wing.
BRONZE BUSHING REPLACEMENT PROCEDURE DN345 & NL450C
1 BRONZE BUSHING REPLACEMENT PROCEDURE V.2 12/3/2014 DN345 & NL450C 2 Safety Instructions Removing Walking Beams 3 1. Position spreader on a flat concrete surface capable of supporting weight of spreader
Here's the comparison of the stock rock shaft vs. a 3pt rock shaft.
This documents a build of a Category 0 3 point hitch for the John Deere 316 Onan, 318, 322, 330, 332, 420 and 430 tractors. This is Neil Koch's build for his 318. Here's the comparison of the stock rock
HermanMiller Aeron. New Aeron Disassembly for Recycling. Materials Identification and Segregation: Tools Required. Step 1
HermanMiller Aeron For more information about our products and services or to see a list of dealers, please visit us at www.hermanmiller.com or call 888-443 - 4357. 2016 Herman Miller, Inc., Zeeland, Michigan
Installing the GRT-4G trigger in Gamo guns with the plastic triggers. These instructions apply to both spring guns and gas ram (IGT) powered guns.
Installing the GRT-4G trigger in Gamo guns with the plastic triggers. These instructions apply to both spring guns and gas ram (IGT) powered guns. Revisewd 7/10/13 CharlieDaTuna Be sure to read the special
MODEL TRIPEX PULLEY SYSTEM
MODEL 922184 TRIPEX PULLEY SYSTEM 1 PARTS LIST FOR TRIPEX PULLEY SYSTEM Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your
3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO
NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
Precision Liquid Settlement Array Manual
Precision Liquid Settlement Array Manual All efforts have been made to ensure the accuracy and completeness of the information contained in this document. RST Instruments Ltd reserves the right to change
// ADapters GUIDelines
// ADapters GUIDelines ADAPTER SELECTION Selection of an appropriate ALFAGOMMA adapter for a given application depends on the fluid system operating parameters listed below and the tube material and wall
Aquor House Hydrant V2
Aquor House Hydrant V2 IN-WALL OUTDOOR FAUCET SYSTEM FLUSH-MOUNT QUICK-CONNECT SELF-DRAINING ANTI-SIPHON NON-FREEZE VBH-SERIES AQUOR HOUSE HYDRANT V2: WALL HYDRANT / FREEZELESS SILLCOCK Freezeless sillcock
OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL)
OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) Table of Contents ASSEMBLY ASSEMBLY Pistol Bullet Feeder... Page 3 CHANGE-OVERS The Hornady Lock-N-Load Pistol Bullet Feeder is capable of feeding most
Folding Dual Suspension MTB. Instruction Manual
Folding Dual Suspension MTB Instruction Manual Introduction The Stowabike Folding MTB has been made to last and with proper maintenance, it will give you years of enjoyable rides and journeys. The following
CHAPTER 5 REWIND STARTERS
GENERAL INFORMATION CHAPTER 5 REWIND S Rewind starters used on vertical shaft Tecumseh engines are top mount horizontal pull style or side mount vertical pull style. Horizontal shaft engines use side mounted
HANDLE WITH CARE FLUTE CLARINET
HANDLE WITH CARE FLUTE RH thumb should be on its side, and not in a hitchhiker position. RH thumb and 1 st finger should always point in the same direction. RH should be slanted toward Eb key; never toward
Lock-N-Load. Bullet Feeder
Lock-N-Load Bullet Feeder table of contents steps Overview... 2 List of required hand tools... 2 1: Mounting the Bullet Feeder to the Bench... 3 2: Mounting the Bullet Feed Hopper... 4 3: Bullet Feed Hopper
Brookwood High School Marching Fundamental Handbook
Brookwood High School Marching Fundamental Handbook 2016 -- 2017 11250 George Parkway Brookwood, AL 35444 Welcome to the Brookwood High School Marching Band family! This handbook contains all of the marching
American Flagpole & Flag Co. 1(800)
SENTRY CONCEALED HALYARD-REVOLVING TRUCK GROUND SET INSTALLATIONS INSTRUCTIONS 1. Dig foundation as detailed in SECTION A FOUNDATION SPECIFICATIONS, set sleeve in enter of hole with top 2 above grade.
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Ballpark Classics Baseball Game MLB Edition Figure B Read the instructions completely before beginning g assembly. You will need a Phillips screwdriver. 1. Remove the game from the
WHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
ZODIAC 601 XL. Position the main spar parallel to the edge of the workbench. Raise the wing skeleton on steel beams or spacers.
Check: Sight down the rear channel 6W7-1 and the spar, check that they are straight. The aft edge of the channel is the reference to position the Rear skins. Position the main spar parallel to the edge
LEGACY II TM STARTING PLATFORMS
LEGACY II TM STARTING PLATFORMS INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 (503) 266-2231 Fax (503) 266-4334
UltRo Dual Flow Reverse Osmosis Water System
UltRo Dual Flow Reverse Osmosis Water System Congratulations on this great investment to your health. **IMPORTANT NOTE BEFORE YOU BEGIN** We recommend you call your local friendly plumber to ensure proper
RB70 Automatic Diluent Valve Maintenance Manual. Version 1.1 November 2006 Written by Tino de Rijk. Page 1 of 23
RB70 Automatic Diluent Valve Maintenance Manual Version 1.1 November 2006 Written by Tino de Rijk Page 1 of 23 Table of Contents 1. Introduction... 3 2. ADV diagram and parts list (Pre June 2006)... 4
L-23 Super Blanik Rigging (assembly/disassembly) Guide Maj Carl Kerns
L-23 Super Blanik Rigging (assembly/disassembly) Guide Maj Carl Kerns The L-23 Blanik is a difficult Sailplane to rig (assemble). The wings are heavy and are secured via a single
Ref Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket
Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P
Exercise #1: The Half Pass
THE CANTER ZIG ZAG So, you're thinking about moving your horse up to Intermediare II. Congratulations! It's an exciting step. You've been schooling all the movements and systematically building up to this
TRAINING TASK 1- for regional heat skill competition
TRAINING TASK 1- for regional heat skill competition General Information Standards Complete the task within 2 hrs. The standard of work required to gain maximum marks are: it yourself or ask a fellow student
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
Spilt body Flange ball valve. TC-205MFF-PN1640 User Manual English Version. Document No: TC-205MFF-PN1640.Ur-manual. Date: 2007/04/2617. Version: 1.
Spilt body Flange ball valve TC-205MFF-PN1640 Series PED Category I,II TC-205MFF-PN1640 User Manual English Version Use for company in Europe who will place the product on the market, please amend which
VALVES & MEASUREMENT
VALVES & MEASUREMENT TBV OPERATION AND MAINTENANCE MANUAL SERIES 1100: THREE PIECE BALL VALVE For technical questions, please contact the following: Engineering Department 1537 Grafton Road Millbury, MA
1.2 LIMITATIONS: Consider the following application limitations before using this equipment:
User Instruction Manual Standing Seam Roof Anchor This manual is intended to meet the Manufacturer s Instructions, and should be used as part of an employee training program as required by OSHA. Figure
NEXT GENERATION FLEX FENCE
NEXT GENERATION FLEX FENCE Area To Be Fenced.. With Next Generation Flex Fence any post that is not in a straight line with another post must be braced. Layout your fence installation. Determine all end
APCO ARV CLEAN WATER AIR RELEASE VALVES. Model 50A
APCO ARV CLEAN WATER AIR RELEASE VALVES Model 50A Instruction D12013 February 2017 Instructions These instructions provide installation, operation and maintenance information for APCO ARV Clean Water Air
Final Assembly Instructions Bikes with Quill Stems
Final Assembly Instructions Bikes with Quill Stems Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
2990 Lorne Scots Royal Canadian Army Cadet Corps Rifle Drill
2990 Lorne Scots Royal Canadian Army Cadet Corps Rifle Drill Page 1 of 27 TABLE OF CONTENTS PARA ITEM PAGE Section 1 BASIC RIFLE DRILL 1.1 INTRODUCTION 3 1.2 ATTENTION 5 1.3 STAND AT EASE FROM ATTENTION
Boat Boat Loader Fitting Instructions
Aerodynamic & Heavy Duty Roof Rack Systems Australian Made - Australian Owned www.rhinorack.com Boat Boat Loader Fitting Instructions CONTROLLED Balance point 3 Front eye nuts position 3 Transom eye nut
CARL GOLDBERG PRODUCTS, LTD. P.O. Box 818 Oakwood GA Phone # Fax #
Superfloats 36 ARF WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could
S-60-TO : 1 ton tower system INSTRUCTION MANUAL
S-60-TO : 1 ton tower system INSTRUCTION MANUAL LIVE SYSTEMS bvba Mandellaan 282 8800 B-Roeselare Tel: +32(0)51 69 38 14 Mobile : +32 (0) 495 24 24 67 e-mail: ricky@livesystems.be BTW : 0859.636.665 1
Trilogy Theory of Operation
INSTALLATION & OVERVIEW... 2 Load Height... 2 Approach Angle... 2 Footprint... 3 Protrusion... 3 Mounting the... 4 General Torque Specs... 4 OPERATION OF BIKE RACK... 5 Loading Bikes... 5 Unloading Bikes...
3/4 SafeClaw Anchorage Connectors
Operations and Instruction Manual Model #4075 Portable Concrete Anchorage Connector ANSI Z359.1-07 5,000 lbs / 22kn OHSA 1910.66 & 1926.502 Effective: 01/2012 Expires: 01/2022 IM-0049 REVA 3/4 SafeClaw
DO IT YOURSELF WHEEL STRAIGHTENING For the FORD MODEL A
Check back to my website for updates to the following document. Look for the document on my Services page. As I develop new processes, I will revise the document and share the info. Thank You. Dave Gerold
Now simply cut away the old bushing. You may want to clean the bar of any rust, scale,
If you find that you have a rattle in the rear of the car that you can't pin down, it is possible that your rear sway bar bushings are on the way out. In my case, I was told during my biannual inspection
Sterling Shotguns. Field and Target Models. Owner s Manual
Sterling Shotguns Field and Target Models Owner s Manual If you have any questions about the safe use of a Big Horn Armory firearm, call us at 307-586-3700 or write us at P.O. Box 940, Cody Wyoming 82414.
WHEATLEY Series 500 Swing Check Valve
Document Number: TC003001-13 Revision: 02 WHEATLEY Series 500 Swing Check Valve Installation, Operation, and Maintenance Manual TABLE OF CONTENTS BILL OF MATERIALS...3 SCOPE...5 INSTALLATION AND OPERATION