Safety Risk Assessment Carpentry
|
|
- Suzan Barrett
- 5 years ago
- Views:
Transcription
1 One Direct aintenance td Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees ark Bloxidge H&S anager General carpentry activities including, B Contractors/Sub contractors hanging doors, skirting, architrave, sheet C Tenants D embers of the public materials, flooring, windows, fitting of kitchen units and worktops. Work Type Review Date Routine July 2019 Hazard/ Severity Probability Existing Additional Required 1) anual handling A,B,C,D S F 1) Operatives are trained and competent in the task 1) Document operative training and competence Sprains and strains, impact injury, lacerations 2) Safety footwear to be worn at all times 3) Gloves available for use where required to prevent splinters and pinch injuries 2, 3) PPE to be issued, recorded, monitored and replaced where appropriate 4) Ensure correct resources are allocated as required 4) Resources available for team lifts where appropriate 1, 2, 3, 4, 5) See SRA for manual handling 5) Order timber in easy to handle sizes and quantities where possible T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 1
2 One Direct aintenance td Hazard/ Severity Probability Existing Additional Required 2) Use of hand tools Cuts and abrasions, flying objects A,B,C,D S F H 1) All tools to be maintained in good condition 2) Tools to only be used for the task intended in line any manufactures instructions 3) All tools to be inspected by the user prior to use 4) All tools to be appropriately stored to avoid damage 1, 2, 3, 4, 5) Condition and appropriate use of hand tools to be checked during H&S inspections 6) PPE to be issued, recorded, monitored and replaced where appropriate 5) All damaged tools to be removed from use immediately 6) Appropriate PPE to be supplied and worn as identified 7) Prevent use of tools by unauthorised persons 8) See SRA for hand and power tools T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 2
3 One Direct aintenance td Hazard/ Severity Probability Existing Additional Required 3) Use of power tools Cuts and abrasions, flying objects, entanglement A,B,C,D S F H 1) All tools to be maintained in good condition 2) Tools to only be used for the task intended in line any manufactures instructions 3) All tools to be inspected by the user prior to use 1, 2, 3, 4, 5, 6, 7, 8, 9, 13, 14) Condition and appropriate use of hand tools to be checked during H&S inspections 11) PPE to be issued, recorded, monitored and replaced where appropriate 4) All tools to be guarded as per manufacturer s instructions 5) Guards to be inspected regularly 6) All tools to be covered under an appropriate PAT schedule 7) All tools to be battery powered or 110V 8) Ensure that all cables are secured to avoid trip hazards 9) Ensure dust extraction is fitted to all tools if required 10) Prevent use of tools by unauthorised persons, to include tenants and members of the public T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 3
4 One Direct aintenance td Hazard/ Severity Probability Existing Additional Required 11) Appropriate PPE to be supplied and worn as identified 12) Allow sufficient space to work safely 13) All tools to be appropriately stored to avoid damage 14) All damaged tools to be removed from use immediately 15) See SRA for hand and power tools T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 4
5 One Direct aintenance td Hazard/ Severity Probability Existing Additional Required 4) Hazardous substances Exposure hazardous substances, including dust and wood dust, asbestos A,B,C,D S F H 1) Consult COSHH inventory list and control approach prior to the use of or creation of hazardous substances or materials 2) Appropriate PPE to be supplied and worn as identified 3) Consult appropriate asbestos information for the property / task 2) PPE to be issued, recorded, monitored and replaced where appropriate 3) Stop work if unsure about asbestos information provided for the task and report to supervisor / manager See Contingency Item 4 4) Hover up dust, don t sweep 5) Avoid the use of hard woods and DF where possible 5) Noise Exposure to high levels leading to occupational hearing loss A,B,C,D S P H 1) ost work is restricted to short duration 2) Use self-dampening tools where available 3) Appropriate PPE to be supplied and worn as identified 1) Noise monitoring to be carried out for tasks and equipment that fall outside the scope of short duration 2) Hearing protection to be worn for all equipment that exceeds levels of 85db T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 5
6 One Direct aintenance td Hazard/ Severity Probability Existing Additional Required 6) Hand arm vibration Exposure to occupational injuries to blood vessels, nerves and joints A S P H 1) Tools built in HAV dampener protection to be used where available 2) Gloves to be worn when using tools that generate vibration or impact 1, 2) HAV questionnaires to be completed for all operatives, any existing conditions or new symptoms to be referred to occupational health adviso 7) Slips, trips and falls Trips on trailing cables or materials, Falls from height A,B,C,D S P H 1) All cables to be taped down, covered or attached at a high level to prevent trip hazards 2) All materials and waste to be tidy or removed from site to maintain good housekeeping standards and prevent trip hazards 1,2) To be monitored during H&S inspections 2) Regular waste collections to take place in order to prevent buildup of waste on site 3) See SRA s for working at height 3) Appropriate controls to be implemented for all working at height to prevent falls T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 6
7 One Direct aintenance td Hazard/ Severity Probability Existing Additional Required 8) Contact electricity Electrocution A,B,C,D Cr O 1) Timber or sheet materials to be cut or drilled where the presence of electrical cable is unknown to be checked first cable protectors 2) safe isolation procedures should be observed See Contingency Item 2 2) Electrical supply to be isolated where carpentry work is taking place which presents a risk of contact live cables 9) Injury to others Injury to others as a result of work activities including tenants and members of the public A,B,C,D O 1) Ensure work areas in communal areas are appropriately cordoned off and safety signage is in place 2) When working in occupied properties ensure that tenant is aware of works being under taken and any associated risks 1) See working in communal areas risk assessment 10) Working at Heights Injury from falls or being struck by falling objects A,B,C,D S F H 1) Ensure correct means of access equipment or working platform is identified for every task 1) See SRA s for working at height T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 7
8 One Direct aintenance td Personal Protective Equipment required (PPE): Icon Glossary HARD HAT NO HAND PROTECTION SAFETY VISOR HIGH VIZ NO SAFETY FOOTWEAR DUST ASK EYE PROTECTION EAR PROTECTION T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 8
9 One Direct aintenance td Contingency Plan Item No Hazard/ Occurrence Contingency/Action 1 Unauthorised entry to working area. Violence and aggression / public access to restricted work area 2 Electricity failure / flood / pipe leak / striking cable / pipework ighting failure / water in premises / electrocution 1) Aggressive behaviour / damage to access equipment 1) Work would cease. Unauthorised visitors asked to leave One Direct supervisor informed. Emergency services called if required. 2) one working procedure in place. 1) Severance of services / lighting failure. 1) Work would cease and client would be informed by One Direct Supervisor so remedial work can be carried out in order for the work to re-start. 3 Poor communication / lack of contact between direct labour and subcontractors Poor standards / work being carried out in an inappropriate manner 1) Poor standard of work / low customer satisfaction / violent and aggressive behaviour from customer 1) One Direct supervisor to keep all parties informed of work procedures and standards, H&S inspections to take place 4 Disturbance of asbestos containing materials Exposure to asbestos related illness 1) ack of appropriate asbestos information supplied for the property / task 2) Failure to comply asbestos procedures 1) Implement emergency asbestos procedure. T = Tolerable, = ow, = edium, H = High, N = Intolerable Page 9
Safety Risk Assessment Hand and Power Tools
One Direct aintenance td Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees ark Bloxidge H&S anager 0208 821 5197 Use of hand and power tools B Contractors/Sub
More informationSafety Risk Assessment Driving Grey Fleet Vehicles
One Direct Maintenance td Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees Mark Bloxidge H&S Manager 0208 821 5197 One Direct staff driving their
More informationSafety Risk Assessment Roofing Works / Surveying / Inspections
One Direct aintenance td Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees ark Bloxidge H&S anager 0208 821 5197 One Direct Operatives accessing roof
More informationSafety Risk Assessment Working at Height: Mobile Tower Scaffold
Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees Mark Bloxidge H&S Manager 0208 821 5197 Working at height from Mobile Tower B Contractors/Sub contractors
More informationUniversity College Dublin Machinery/Equipment Risk Assessment Template
1. General Information Name of Person(s) carrying out assessment and their position Principal Investigator / Supervisor / Head of School or Unit (Person responsible for ensuring safety) Date of assessment
More informationSAFE WORK METHOD STATEMENT Part B
SAFE WORK METHOD STATEMENT Part B SWMS No.: 01 WORK ACTIVITY DESCRIPTION: Door Installation All FORESEEABLE OHS & ENVIRONMENTAL HAZARDS & RISKS ASSOSSIATED WITH THE WORKS MUST BE ASSESSED & ALLOCATED CONTROLS
More informationRisk Assessment Form (Qualitative)
Assessment Form (Qualitative) Project / ocation:..d.a.s WATERS Contract No: RA & Issue No: 008 Prepared by:.r.smit Date: 10/10/16 Signature: ACTIVITY DESCRIPTION: Person (s) at risk: General Ground works
More informationPre-control risk estimate. Likelihood Risk
Activity Consequence s mitigation measures Site Access & Egress Slips, trips & falls al injury by falling. Sprains & broken bones. Site operatives 3 4 12 Ensure access to site is kept clear of plant &
More informationCOSHH Hazardous Substances Health & Safety Management Standard Issue 2 (September, 2010)
COSHH Hazardous Substances Health & Safety Management Standard Issue 2 (September, 2010) Introduction This document contains corporate standards and guidance on the management of risks arising from the
More informationFIRE HYDRANT TESTING METHOD STATEMENT.
SUBJECT: TASK: FIRE HYDRANT INSPECTION & TESTING. 1. Location....1 2. The Scope of Works.... 1 3. Description of Task.... 1 4. Access & Egress to & from Work Area.... 2 5. Safety Hazard Identification....
More informationPotential hazards People at risk and how? Actions already in place Further action required Action by
Risk Assessment Flat Roof Repair Prepared by Oracle Managed Services For: BAM FM On: 24/02/2017 Review date: N/A Potential hazards People at risk and how? Actions already in place Further action required
More informationSafe Work Method Statement
Company Name: Safe Work Method Statement Site Address: Other Details: Contractor: Activity/Trade: Electrician Date: TASKS List the tasks required to perform the activity in sequence carried out. Entry
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT WATER PUMP - PETROL Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationADRAIN SAFETY MANAGEMENT LTD. MCN Ltd RISK ASSESSMENT SHEET
Description of task: ADRAIN SAFETY MANAGEMENT LTD. MCN Ltd SHEET Manual Handling of Loads Number of operatives Exposed : 4-6 Operatives 1. Muscle strains/ sprains/torn ligaments 2. Fractures from dropped
More informationPersonal Protective Equipment
Northland Community & Technical College June 1, 2017 Personal Protective Equipment Safety Officer Cory Feller Chemical Hygiene Officer Kristel Kizer Telephone: 218-683-8633 1 Personal Protective Equipment
More informationSection J. How to develop safety elements for project safety management system. How to develop safety elements for project SMS
Section J How to develop safety elements for project safety management system 1. Once the project management has developed or adopted a safety policy, it needs to develop safety elements to meet the objectives
More informationRisk Assessment. Appendix A contains
Risk Assessment Department The Cockpit Risk Assessment number AM/09/01 Date. 1 st July 01 Review due date 0 th July 01 Activity Maintenance and support service working Location The Cockpit Name of Assessor/s
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT AUGER / POST HOLE DIGGER Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationEXHIBITION Guide. Roles and Responsibilities OS11. A handbook for exhibitors and contractors
Appendix 1 Health & Safety Declaration, Roles and Responsibilities Each exhibitor and Informa appointed contractor must complete the Health and Safety Declaration form provided below to confirm they have
More informationPLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO LOW LEVEL LIGHT UNITS
PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO LOW LEVEL LIGHT UNITS Project: Insert Client Repair/ Replacement of low level light units/ low level
More informationRisk assessment. Assessment details. Task. Introduction. Please complete the form as fully and accurately as you can. Assessors job title
Risk assessment Introduction Please complete the form as fully and accurately as you can. Assessment details Name of organisation Assessor's name Assessors job title Any Company John Smith Manager Date
More informationMethod Statement Author
Plan Bee Limited 3.3 Etna Industrial estate Clamp Road Motherwell Scotland ML2 7XQ Tel: 01698580572 Method Statement Method Statement Details Method Statement Number 7 Method Statement Date Monday 3rd
More informationImportant Safety Information Enclosed
Important Safety Information Enclosed ShedBoss Safety Pack NOTE: ENSURE YOUR CONSTRUCTION CREW RECEIVES THIS PACK TO COMPLY WITH SAFE WORK AUSTRALIA CODE OF PRACTICE www.shedboss.com.au Important Safety
More informationPersonal Protective Equipment
Personal Protective Equipment General This section addresses eye, face, head, hand and foot protection. respiratory and hearing protection. Separate programs exist for Employees will be provided personal
More informationWest Midlands Police Risk Assessment Form
Assessment Form Assessment Subject/Area: Tasks associated with the execution of warrants URN (PU/001) etc): 01/2013 Assessed By: Assessment Date: 21/09/13 Review Date: September 2014 Assessor Responsibility
More informationTASK DAY RISK ASSESSMENT FORM
TASK DAY RISK ASSESSMENT FORM Assessment date Location and Activity details: Site Address Step One - Identify the activity and hazards Consider the activity or work area and identify if any of the hazards
More informationPotential risk of injury to staff
Register Fire, Earthquake - other Emergencies Manual Handling and Repetitive Work Repetitive, Forceful Work Poor Housekeeping Not Wearing PPE (Personal Protective Equipment) Potential risk of injury to
More informationCONSTRUCTION HEALTH AND SAFETY MANAGEMENT SYSTEM BASELINE HIRA
RECOMMENDED ADDITIONAL CONTROLS TASK / ACTIVITY/ EQUIPMENT/ FACILITY HAZARDS UNWANTED EVENT MINIMUM CONTROLS REQUIRED RISK NO. LIKELI-HOOD CONSE-QUENCE RISK VALUE Project Risk Assessment Page 1 of 16 All
More informationEHS Workplace Inspection Checklist (Ref. SOP QMS-080; EHS-010)
(Ref. SOP QMS-080; EHS-010) Form-445 Inspected by: Date of inspection Date of Report Report # Pages Area Manager: Area Inspected: General This EHS Workplace Inspection was conducted by: Scope of the Inspection:
More informationWorkplace Safety Inspection Sheet
Workplace Safety Inspection Sheet Record all details of a safety inspection carried out at your workplace 1 of 2 Date and Time of Inspection:... Area or workplace inspected:... Name(s) and signature(s)
More informationCONSTRUCTSAFE TIER 1 HEALTH AND SAFETY COMPETENCY TEST FRAMEWORK
CONSTRUCTSAFE TIER 1 HEALTH AND SAFETY COMPETENCY TEST FRAMEWORK ConstructSafe Project Team March 2018 Version 1.3 1 Table of Contents 1. Introduction... 3 2. Candidate minimum required knowledge... 3
More informationWhat we are already doing Working at Height comes within the framework of St. Matthew s Health and Safety and Fire arrangements policy
Risk Assessment For: Assessment signed off by (Warden): Assessment signed off by (Clergy): Working at Height Please also see separate risk assessment for Use of Stepladders Assessment carried out by (H&S):
More informationManual Handling Procedure
Manual Handling Procedure Table of Contents 1 Purpose... 3 2 Scope... 3 3 Definitions... 3 4 Responsibilities... 3 4.1 Managers And Supervisors... 3 4.2 Workers (Employees, Contractors And Visitors)...
More informationSCOPE OF WORK, SAFETY METHOD STATEMENT & RISK ASSESSMENT
SCOPE OF WORK, SAFETY METHOD STATEMENT & RISK ASSESSMENT Prepared for:- Date:- Work Scheduled:- SCOPE OF WORK Carry out installation of flow meters / pressure sensors. Installation of flow meter procedure
More informationQUEENSLAND UNIVERSITY OF TECHNOLOGY
QUEENSLAND UNIVERSITY OF TECHNOLOGY SITE SPECIFIC SAFETY MANAGEMENT PLAN FOR SAMFORD HOUSE SAMFORD ECOLOGICAL RESEARCH FACILITY SAMFORD VALLEY 2007 Dylan Randall SN: 06305466 dylan.randall@student.qut.edu.au
More informationB S Glass Ltd Safety procedures- outsourced Workplaces
B S Glass Ltd Jan 17 B S Glass Ltd Safety procedures- outsourced Workplaces Index - - - - - - - - Page No On Site safety - - - - - - - - - - - - - - - - - - - Content 3. 1.00 Health and Safety Mission
More informationHealth & Safety Contractor rules
Health & Safety Contractor rules Contents 1. Introduction... 1 2. The legal bit explaining our terminology... 1 2.1 Legal requirements... 1 3. Our health and safety requirements... 1 3.1 Access to BT premises...
More informationSpecific Safety Legislation/Codes of Practice/Australian Standards applicable to this JSA (Tick those applicable).
OCCUPATIONAL HEALTH & SAFETY MANUAL Section OHS-005, Job Safety Analysis SCORESBY, VIC 3179 GEELONG, VIC 3218 MALAGA, WA 6090 DUDLEY PARK, SA 5008 MANSFIELD, QLD 4122 NORTH ROCKS, NSW, 2641 ACT 2609 LAVINGTON,
More informationHow severely could the risk hurt someone? Low/Insignificant First aid
Safe Work Method Statement No: WMS-02 Task: Concreting, Formwork and Steel Fixing This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia)
More informationBHC-P-07.2 Health Hazards in Construction
BHC-P-07.2 Health Hazards in Construction Contents 1.0 Purpose 2.0 Scope 3.0 Definitions 4.0 Main requirements 5.0 Guidance documents and references 6.0 Appendices Revision Register Date Version Description
More informationPersonal Protective Equipment
Policies & Procedures Personal Protective Equipment Internal Procedure: PPE Effective Date: 7-30-18 Last Modified: 7-30-18 Approved By: Todd Barnette Purpose To establish requirements for a Personal Protective
More informationTUDOR PARK EDUCATION TRUST. Working at Heights and Risk Assessment
TUDOR PARK EDUCATION TRUST Working at Heights and Risk Assessment Person(s) responsible for updating the policy: Chief Executive Officer Date Approved: Board of Directors on 7 July 2016 Period of Review:
More informationMain Activity Hazard Rating Hazard Controls CLW Policy/Procedure
Job Hazard Analysis Position: Employment Direct Support Professional Completed by: Health & Safety Committee Date: November 11, 2016 Main Activity Hazard Rating Hazard Controls CLW Policy/ Providing Support
More informationTemporary load-bearing support for structural alterations or repairs
CRITICAL NOTE This document only becomes a Safe Work Method Statement where the High Risk Construction Work section of this document is completed Company: ABN: Contact Person: Ph: Project/Site: Principal
More informationPrint this activity then complete it and keep it as evidence in your folder, or portfolio.
Workplace hazards Workplace Learning and Assessment Activity Workplace Learning and Assessment Activity Print this activity then complete it and keep it as evidence in your folder, or portfolio. Hazard
More informationLeicester City Council Health & Safety Risk Assessment Form Ref:
Division/Section: Bridges Team Work Activity: Structural Repairs Activity Location: 8 Minehead Street, Leicester Persons Affected: Manager: Date of Assessment: Property Occupiers and Site Operatives Abul
More informationMobile Training Unit (MTU)
Mobile Training Unit (MTU) The MTU provides a convenient way of meeting training requirements by bringing a range of short duration health & safety and operative training onsite. Through the MTU, employees
More informationHAZARD RECOGNITION EVALUATION and CONTROL
What is a hazard? HAZARD RECOGNITION EVALUATION and CONTROL Hazard - a dangerous object, event, behaviour or condition (in the workplace) which has the potential to cause injury, illness or property damage.
More informationContractor handbook. Purpose
Page no: 1 / 6 Contractor handbook Purpose Mitie aims to ensure that the highest levels of performance are achieved by all persons working for us or on our behalf. We require the same level of performance
More informationTHICKNESSER RISK ASSESSMENT (U003ra)
Task Being Carried Out: Area: Persons at Risk: Operation of T500 Thicknesser Brindle Mill Operatives, Maintenance engineers Description of Equipment: Wadkin T500 Thicknesser Serial No.: T500 82240 (Machine
More informationHS329 Risk Management Procedure
HS329 Risk Management Procedure Work Health and Safety Act 2011 Policy hierarchy link Work Health and Safety Regulation 2011 Work Health and Safety Policy Code of Practice How to Manage Work Health and
More informationPLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO HIGH LEVEL LIGHT UNITS
PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO HIGH LEVEL LIGHT UNITS Project: (insert Client) Replacement/ Repair of high level light units/ high
More informationHEALTH & SAFETY POLICY. Mitigation Policy: Training, including safety awareness training for employees required to work at height.
HEALTH & SAFETY POLICY ACEC INVESTMENTS LIMITED The construction industry accident fatality rate stands at more than double that of all sector average more minor accidents are almost incalculably more.
More informationInstructions for the Use of the Excel Spreadsheet. There are Three tabs at the bottom of this worksheet. Instructions tab is the one you are reading
Instructions for the Use of the Excel Spreadsheet There are Three tabs at the bottom of this worksheet Instructions tab is the one you are reading H&S Plan Tab The Plan Tab is the front cover pages of
More informationRisk Assessment In accordance with the Management of Health and Safety Regulations 1999
Ref No 6.1 Task of Assessor Job Title Litter Picking on and around Streets and Highways Below 40mph Simon Foley Location Quality Health and Environmental Manager Bath Signature Issue Date 15 th July 2015
More informationTHE CONTROLLED COPY OF THIS DOCUMENT IS ON THE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR THE DATE AT THE BOTTOM OF THE PAGE.
TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Using Angle Grinders SWMS No. 8 Authorized and email Signed by the
More informationGENERIC ACTIVITIES NON-AALA RISK ASSESSMENT
FSC Operational Codes of Practice 11 September 2013 No. P01: Out of Classroom Page 1 of 14 Appendix 6: Generic Activities Non-AALA Risk Assessment Appendix 6: GENERIC ACTIVITIES NON-AALA RISK ASSESSMENT
More informationISS Safety Rules. Make safety second nature
ISS Safety Rules Make safety second nature 2 ISS SAFETY RULES ISS SAFETY RULES 3 INTRODUCTION We are a company driven by close to 500,000 strong people spread across 77 countries around the globe. And
More informationBogo Operations Pollution Incident Response Management Plan
Bogo Operations Pollution Incident Response Management Plan Rhyolite Hard Rock Aggregate Quarry 134 Paynes Road BOOKHAM NSW 2582 PO Box 426 COWRA NSW 2794 p: 02 6227 7260 p: 02 6345 4253 e: info@bogoquarry.com.au
More informationThe Sample Company Pty Ltd
Job Safety and Environmental Analysis (JSEA) / Safe Work Method Statement (SWMS) Part 1: Project and Task Identification Process Initiators of SWMSs are responsible for consulting the Project Supervisor,
More informationWorking safely in an engineering environment
Unit 001 Working safely in an engineering environment Level: 2 Credit value: 5 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to work
More informationCOGPOLY39 Meet safety, health and environmental requirements in the workplace
Meet safety, health and environmental requirements in the workplace Overview This unit is for those with responsibilities for meeting safety, health and environment requirements in the workplace. It is
More informationHAZARD REGISTER CONSTRUCTION R E M E M B E R, T H E N U M B E R 1 H A Z A R D I S Y O U FREEPHONE:
HAZARD REGISTER CONSTRUCTION R E M E M B E R, T H E N U M B E R 1 H A Z A R D I S Y O U FREEPHONE: 0800 555 339 WWW.HAZARDCO.COM Monitoring 01 General Use Heavy Machinery Demolition Excavation Construction
More informationRisk Controls Proposed: (in hierarchy order from the most preferred control)
are to be assessed and controlled by eliminating or minimising any risks to health and safety. Eliminate - Where the risk to health and safety is removed from the workplace. Minimise - Where the risk cannot
More informationHealth, Safety and Welfare Policy
Health, Safety and Welfare Policy This Policy is prepared in accordance with section 2(3) the Health and Safety at work etc. Act 1974, with the intention of promoting a safe working environment that will,
More informationMain Activity Hazard Rating Hazard Controls CLW Policy/Procedure Providing support to People who have challenging needs
Job Hazard Analysis Position: Ventures Completed by: Health & Safety Committee Date: February 19, 2015 Main Activity Hazard Rating Hazard Controls CLW Policy/ Providing support to People who have challenging
More informationFLYING OBJECTS MANUAL HANDLING EXCESSIVE NOISE
JOB NO: PROJECT: DATE: SWMS NO: SWMS 002 PREPARED BY: Ian Hartley REVISED BY: Nick Bragg & Cameron McNeil ACTIVITY: STUMP REMOVAL SUPERVISED BY: REVISION DATE: April 2016 MINIMUM PERSONAL PROTECTIVE EQUIPMENT
More informationContractor / Exhibitor Handbook
Contractor / Exhibitor Handbook Health and Safety This booklet outlines the basic rules that must be followed by contractors and other visitors working on Live Promotions Events sites. The contractors
More informationWHS OHS HAZARD REGISTER (SITE AND OFFICE OPERATIONS)
WHS 017 - WHS 017 Hazard Register - Version 5.0 April 20 Doc No: WHS 017 Effective Date: 04/04/20 1 WORKING WITH EARTHMOVING PLANT/ TRUCKS/SITE VEHICLES COLLISIONS OTHER PLANT EQUIPMENT SITE VEHICLES PERSONNELL
More informationSafe Work Practices / Procedures / Instruction CONFINED SPACE
CONFINED SPACE Entry into and work in a confined space poses health and safety problems which may include: Presence or possible build up of a hazardous atmosphere Unexpected movement of equipment or materials
More informationHealth and Safety Policy Statement ENVILLE GOLF CLUB LIMITED
Health and Safety Policy Statement ENVILLE GOLF CLUB LIMITED 2017 Index 1. General statement of health and safety 2. Organisation 3. Scope 4. Responsibilities 5. Management 6. Risk assessments 7. Tools
More informationDUQUESNE UNIVERSITY PERSONAL PROTECTIVE EQUIPMENT (PPE) PROGRAM
DUQUESNE UNIVERSITY PERSONAL PROTECTIVE EQUIPMENT (PPE) PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Hazard Assessment 2 Selection Guidelines
More informationIMMANUEL CHURCH, CHICHESTER HEALTH AND SAFETY POLICY
IMMANUEL CHURCH, CHICHESTER HEALTH AND SAFETY POLICY Approved by the Trustees: November 2016 Health and Safety Policy Introduction The main piece of health and safety legislation is the Health and Safety
More informationSAFE WORK METHOD STATEMENT
SAFE WORK METHOD STATEMENT EXCAVATION OR TRENCHING Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES
More informationPersonal Protective Equipment. OSHA Office of Training and Education 1
Personal Protective Equipment OSHA Office of Training and Education 1 Protecting Employees from Workplace Hazards Employers must protect employees from hazards such as falling objects, harmful substances,
More informationPocklington Town Council Risk Assessment Christmas Festival Wednesday Assessor: Gordon Scaife Date
Activity: Christmas Festival Wednesday Assessor: Gordon Scaife Date 16/07/2018 5 December Completed: Persons At Risk: PTC Staff, Volunteers & Public Reference: 180716 Public Events Review Date: 16/07/2019
More information75 Years of Health and Safety Guidance
H&S Guide: 60 Working Risks Personal Protective Equipment Personal Protective Equipment (also known as PPE) Employers have duties concerning the provision and use of personal protective equipment at work.
More informationCONTROL OF SUBSTANCES HAZARDOUS TO HEALTH (COSHH) POLICY
CONTROL OF SUBSTANCES HAZARDOUS TO HEALTH (COSHH) POLICY INTRODUCTION The practice will monitor and control all substances in the practice with the potential to cause harm to ensure the safe usage and
More informationPERSONAL PROTECTIVE EQUIPMENT
13.0 The purpose of this program is to ensure that, where applicable, the appropriate and necessary personal protective equipment (PPE) is selected and provided to employees to protect from illness or
More informationJOB SAFETY ANALYSIS. How to use the Risk Assessment Charts. Likelihood A (Almost Certain) B (Likely) C (Possible)
Page 1 of 6 How to use the Assessment Charts 1. Determine the Likelihood on the Qualitative Assessment Process Chart (pick a letter applicable to the task). 2. Determine the Consequence on the Qualitative
More informationTwo Main Risks Associated with Foundry Work
Two Main Risks Associated with Foundry Work WHAT IS OCCUPATIONAL HYGIENE? Occupational Hygiene? Occupational Hygiene? NO! Occupational Hygiene? Occupational Hygiene? NO! OCCUPATIONAL HYGIENE is the discipline
More informationDate Issued: November 2011 Revision Date: December 2012 Review Date: December 2015 Revision #
SUNCOR ENERGY PRODUCTS DISTRIBUTION TERMINAL OPERATING MANUAL STANDARD OPERATING PROCEDURE MAINTENANCE TASKS Date Issued: November 2011 Revision Date: December 2012 Review Date: December 2015 Revision
More informationThe Yorkshire Waterways Museum, Dutch River Side, Goole, POND AND NATURE TRAIL RISK ASSESSMENT SHE/RA/00
The Sobriety Project The Yorkshire Waterways Museum, Dutch River Side, Goole, DN14 5TB POND AND NATURE TRAI RISK ASSESSMENT SHE/RA/00 Title of Activity: ocation(s) of Work: Using the pond area and nature
More informationEvent Health & Safety Hazard Plan
Event name Zone 4, A South Island Qualifying ms-girls Event type Girls ms, Basketball City Westport Venue Solid Energy Centre (SEC) Start date 6 th September 2017 End date 9 th September 2017 Event start
More informationTo comply with the OHS Act, the responsible manager must carry out and document the following:
Owner: Manager Health, Wellbeing and Safety Last Update: 10 January 2018 Contents 1. Purpose... 1 2. Minimum Compliance Requirements... 1 3. Definitions... 2 4. Legislative requirements under the OHS Act
More informationHealth and Safety Policy
Health and Safety Policy It is the policy of Riverside to create a safe environment and to encourage ways of working which will ensure the safety of children, employees and all other persons who come onto
More informationNew Licensed Asbestos Manager Training
TRAINING SYLLABUS LICENSED WORK WITH ASBESTOS New Licensed Asbestos Manager Training This unit has twenty-three learning outcomes. 1. Recognise the types, uses and risks of asbestos containing materials
More informationSafe Work Procedure for installation of external cladding
Safe Work Procedure for installation of external cladding This procedure has been formulated to cover safe systems of work for the installation of external cladding. This instruction will be used to reduce
More informationRecognition, Evaluation, and Control of Hazards
Recognition, Evaluation, and Control of Hazards Latest revised date: October 26, 2011 Page 1 of 8 1.0 Introduction Memorial University has established a system for the recognition, evaluation, and control
More information2.0 Management Systems and Documentation
SHE Rules BOW142.3 1.0 Introduction This document details the safety, health and environment rules that apply to anyone accessing Arqiva sites and describes the standards of performance expected. This
More informationHazard Identification and Risk Assessment Form. Risk Assessment
Identification and Form Tool & Machine Work General Various (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed in safe operation of each
More informationA Checklist for a Health and Safety Risk Assessment
A Checklist for a Health and Safety Risk Assessment Business Information Factsheet BIF376 July 2016 Introduction All employers, and certain self-employed workers and contractors, are required to assess
More informationA Health and Safety Tip Sheet for School Maintenance Staff. Did you know? Step 1. Identify job hazards. Step 2. Work towards solutions
INSPECTION Health and CHECKLIST Safety Committees MAINTAINING SAFETY: A Health and Safety Tip Sheet for School Maintenance Staff 1 Maintenance and facilities staff members keep schools operational, safe,
More informationTOOL BOX TALK NO3. Use of P.P.E
Combined Technical Solutions Ltd TOOL BOX TALK NO3. Use of P.P.E OBJECTIVE: Why PPE is important and why it should be looked after Personal Protective Equipment is intended to protect you from risks, which
More informationWORK METHOD STATEMENT ALUMINIUM WINDOWS AND DOORS
ORGANISATION DETAILS Organisation Name: Gedoun Constructions Pty Ltd Contact Name: Joe Gedoun ACN/ABN: 52 284 873 581 Contact Position: Director Address: PO Box 1138, Townsville QLD 4810 Contact Phone
More informationSafe Work Method Statement LRB TREE SERVICES 6 Behland St, Kearneys Spring QLD, 4350 ABN
JOB NO: PROJECT: DATE: 1/1/2018 SWMS NO: SWMS 001.1 PREPARED BY: LUKE BLINCO REVISED BY: ACTIVITY: TREE REMOVAL & PRUNING SIGNED BY: REVISION DATE: MINIMUM PERSONAL PROTECTIVE EQUIPMENT (PPE) REQUIREMENTS
More informationGarbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028. Name Date Signature. Author Jarred Hearle 30/11/2014. Reviewed John Nulty 30/11/2014
Garbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028 Name Date Signature Author Jarred Hearle 30/11/2014 Reviewed John Nulty 30/11/2014 Approved Geoff Selfe 01/12/2014 Key Safety Acts Complete a 5
More informationPERSONAL PROTECTIVE EQUIPMENT
C H A P T E R 9 PERSONAL PROTECTIVE EQUIPMENT 9.1. General Personal protective equipment (PPE) when properly used and maintained saves lives and reduces injury and illness. PPE includes equipment for eyes,
More informationHow severely could the risk hurt someone?
Safe Work Method Statement No: WMS-08 Task: Install Drainage This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia) Pty Ltd Authorised
More informationEnvironmental Health & Safety Policy Manual
Environmental Health & Safety Policy Manual Issue Date 8/24/2009 Updated: 5/8/2018 Policy # EHS-400.03 Personal Protective Equipment 1.0 PURPOSE: In order to protect the health of employees and students,
More information