Nominal O.D. SERIES 110FW. 64mm 89mm 114mm 168mm 222mm 276mm 330mm 391mm 445mm 498mm 552mm

Transcription

1 (DN25) 1.5" (DN40) (DN100) (DN150) (DN200) (DN250) (DN300) 1 (DN350) (DN400) 1 (DN450) (DN500) 2 (DN600) 3 (DN900) 4 (DN1200) 5 (DN1350) O.D. 2.50" mm 1 C L Minimum L Weight (lb/kg) 1.50" 38mm 1.00" 25mm " 51mm 1.25" 32mm " 38mm 2.00" 51mm 2.50" 64mm mm 4.63" 117mm 5.69" 144mm 6.75" 171mm mm 9.00" 229mm mm 11.13" 283mm 13.25" 337mm 16.25" 413mm mm mm 25.13" 638mm 31.25" 794mm to 0.32" (5 to 8mm) up to 2Ø 0.32 to 0.42" (8 to 10.5mm) 2 to 60"Ø NOTE 4. C = 0.5 * O.D. + Pad Thk (0.25" nom. up to 2Ø, 0.3 above 2Ø). NOTE 3. Wear pad to be centered on structural support. NOTE 2. Wear pad to have minimum 120 degrees of contact (max. 180 degrees). NOTE 1. Wear pad to be of the same material as the pipe. FIBERBOND FRP "WEAR" PAD FIG FW ENGINEERED COMPOSITE PIPING SYSTEMS 3

2 (DN100) (DN150) (DN200) (DN250) (DN300) 1 (DN350) (DN400) 1 (DN450) (DN500) 2 (DN600) 3 (DN900) 4 (DN1200) L R D +/- 0. SERIES 20HV, 20FR-E, 20FR16, 20FR20, 20JF, 20JF16, 110FW, 20C, 20HV-D SERIES 20HV-C, 20FR-EC, 20FR16-C, 20FR20-C, 20JF-C, 20JF16-C, 20HV(FDA) (DN25) 3/ 3.25" 83mm 3.00" 76mm 2.75" 70mm 1.5" (DN40) 3/ 3.75" 95mm 3.00" 76mm 3.00" 76mm 0.20 to 0.32" (5 to 8mm) up to 2Ø 0.32 to 0.42" (8 to 10.5mm) 2 to 60"Ø 3/ 1/2" 1/2" 5/ 5/ 3/ 7/ 7/ 7/ 4.25" 5.25" 6.25" " 14.75" 16.95" " mm 3.00" 76mm 3.25" 133mm 159mm 213mm 264mm 317mm 375mm 430mm 485mm 544mm 594mm 703mm 4.00" 4.00" 5.00" 5.00" 5.00" 5.50" 5.50" 5.50" E 127mm 127mm 127mm 140mm 140mm 140mm 4.13" 4.63" " " 11.23" " 14.75" 16.90" F 83mm 105mm 118mm 154mm 181mm 217mm 285mm 313mm 350mm 375mm 429mm mm 5.50" 140mm 19.72" 501mm mm 5.50" 140mm mm T1 NOTE 11. An "extra-long" L dimension of 1 () may be used up to Ø. NOTE 10. Minimum L dimensions per Fig.210 may also be used. NOTE 9. F = C + 1/2in. + 3 * R (or use values in table). NOTE 8. E = 4 * R + 1 1/2in. NOTE 7. C = 0.5 * Avg O.D. + T1 (See Fig.210 for C dimensions). NOTE 6. D = Pipe O.D. + 2 * T1 + R + 1/4in. (or use values in table). NOTE 5. T1 dimension is from T.O.S. to B.O.P. NOTE 4. The u-bolt shall not "anchor" the pipe. NOTE 3. Wear pad to be centered on structural support. NOTE 2. Wear pad to have minimum 120 degrees of contact (max. 180 degrees). NOTE 1. Saddle to be of the same material as the pipe. Rev 12 Changes: Increased "D" dimension in sizes thru 2" by 0.5", in sizes 3" & by 3, in size by 1 and in size by 1. No other changes. RUBBER COATED U-BOLT FIG GENERAL DETAIL 12

3 Butt and strap thrust collar 0.50" (12.5mm) thk (DN150) (DN200) (DN250) (DN300) 1 (DN350) (DN400) 1 (DN450) (DN500) 2 (DN600) 3 (DN900) 4 (DN1200) 5 (DN1350) O.D. L1 C E " 126mm 6.00" 7.07" 180mm 8.13" 207mm 9.32" 237mm mm mm 12.50" 317mm 14.63" 372mm 444mm 20.63" 524mm 12.00" 14.00" 16.00" 18.00" 20.25" 22.25" " 30.75" 37.25" " 68.00" 458mm 514mm 565mm 622mm 673mm 781mm 946mm 1105mm " 592mm mm 32.50" 825mm 1422mm 1727mm 0.5 (14mm) hole up to Ø (3/ bolt) 0.69" (17.5mm) hole up to 2Ø (1/2" bolt) 0.8 (20.5mm) hole up to 30"Ø (3/ bolt) 0.9 (24mm) hole up to 3Ø (7/ bolt) 1.0 (27mm) hole up to 4Ø ( bolt) 1.19" (30mm) hole up to 60"Ø (1 1/ bolt) xx1/ Field weld (TYP.2) NOTE 5. Average O.D. is typically 0.03" to 0. larger than the nominal O.D. NOTE 4. C = 0.5 * O.D in. NOTE 3. Steel saddle includes 1/8in. thick neoprene liner. NOTE in. (41mm) dimension is from T.O.S to B.O.P. NOTE 1. Thrust collar may need to be larger depending upon design conditions. STEEL ANCHOR FIG FW 1

4 O.D. L1 C 2.50" 64mm 1.63" 41mm 2.13" 54mm (DN100) 2.63" 67mm (DN150) 3.70" 94mm (DN200) mm (DN250) " 148mm (DN300) mm 1 (DN350) " 205mm (DN400) 9.13" 232mm 1 (DN450) 10.19" 259mm (DN500) 11.25" 286mm Butt and strap thrust collar 0.50" (12.5mm) thk 2 (DN600) 3 (DN900) mm 16.25" 413mm mm 4 (DN1200) (DN1350) xx1/ 0.5 (14mm) hole up to Ø (3/ bolt) 0.69" (17.5mm) hole up to 2Ø (1/2" bolt) 0.8 (20.5mm) hole up to 30"Ø (3/ bolt) 0.9 (24mm) hole up to 3Ø (7/ bolt) Field weld (TYP.2) NOTE 5. Average O.D. is typically 0.03" to 0. larger than the nominal O.D. NOTE 4. C = 0.5 * O.D in. NOTE 3. Steel saddle includes 1/8in. thick neoprene liner. NOTE in. (9.5mm) dimension is from T.O.S. to B.O.P. NOTE 1. Thrust collar may need to be larger depending upon design conditions. SMALL STEEL ANCHOR FIG FW 1

5 O.D. A B C 64mm mm 3.00" 76mm 4.25" 108mm mm 4.75" 121mm (DN100) mm 4.00" 5.25" 133mm (DN150) mm mm mm Butt-and-strap thrust collar 0.50" (12.5mm) thk (DN200) (DN250) (DN300) " 141mm " 8.25" 155mm 183mm 209mm 7.37" " 187mm 214mm 241mm 1 (DN350) " 199mm mm 10.69" 271mm (DN400) mm 10.50" 267mm 11.75" 298mm 1 (DN450) mm mm mm 3" (76mm) 2"Ø to Ø 5" (127mm) 1Ø to Ø () 1Ø to 30"Ø () 3Ø to 42"Ø 9" (229mm) 4Ø to 60"Ø (DN500) 2 (DN600) 3 (DN900) " 13.13" 16.00" 19.13" 21.82" 279mm 333mm 486mm 554mm 12.62" 320mm 13.87" 352mm 14.75" 375mm 16.00" 17.63" 448mm mm 20.75" 527mm 22.00" 559mm mm 24.69" 627mm 4 (DN1200) mm 26.50" 673mm 27.75" 705mm 5 (DN1350) 31.00" 787mm 32.62" 829mm 33.87" 860mm 0.5 (14mm) hole up to Ø (3/ bolt) 0.69" (17.5mm) hole up to 2Ø (1/2" bolt) 0.8 (20.5mm) hole up to 30"Ø (3/ bolt) 0.9 (24mm) hole up to 42"Ø (7/ bolt) 1.0 (27mm) hole up to 4Ø ( bolt) 1.19" (30mm) hole up to 60"Ø (1 1/ bolt) PLAN NOTE 5. 'A' dimension is from pipe centerline to neoprene/steel interface. NOTE 4. A = 0.5 * O.D in. NOTE 3. B = 0.5 * O.D in.; C = B in. NOTE 2. Steel saddle includes 1/8in. thick neoprene liner. NOTE 1. A separate bonded collar (two halves) may also be used. STEEL RISER CLAMP FIG FW 0

6