Operating manual. ProSpray Airless high-pressure spraying unit. Model: Original operating manual. ProSpray 3.39

Transcription

1 Operatng manual ProSpray.9 Arless hgh-pressure sprayng unt Model: Orgnal operatng manual ProSpray.9 Edton 5 / L

2 Warnng! Attenton: Danger of njury by njecton! Arless unts develop extremely hgh sprayng pressures. Never put your fngers, hands or any other parts of the body nto the spray jet! Never pont the spray gun at yourself, other persons or anmals. Never use the spray gun wthout safety guard. Do not treat a sprayng njury as a harmless cut. In case of njury to the skn through coatng materals or solvents, consult a doctor mmedately for quck and expert treatment. Inform the doctor about the coatng materal or solvent used. The operatng nstructons state that the followng ponts must always be observed before startng up:. Faulty unts must not be used.. Secure WAGNER spray gun usng the safety catch on the trgger.. Ensure that the unt s properly earthed. 4. Check allowable operatng pressure of hgh-pressure hose and spray gun. 5. Check all connectons for leaks. The nstructons regardng regular cleanng and mantenance of the unt must be strctly observed. Before any work s done on the unt or for every break n work the followng rules must be observed:. Release the pressure from spray gun and hose.. Secure the WAGNER spray gun usng the safety catch on the trgger.. Swtch off unt. Be safety conscous! ProSpray.9

3 Contents Page. Safety regulatons for Arless sprayng Explanaton of symbols used Electrc Safety Electrostatc chargng (formaton of sparks or flames) General vew of applcaton Applcaton Coatng materals Descrpton of unt Arless process Functonng of the unt Legend for explanatory dagram ProSpray Explanatory dagram ProSpray Techncal data Transportaton Transportaton n vehcle Pantng materal setup Textu materal setup Startng operaton Hgh-pressure hose, spray gun and separatng ol Control panel ndcators Pressure control knob settngs Connecton to the mans network Cleanng preservng agent when startng-up of operaton ntally Takng the unt nto operaton wth coatng materal Dgtal Electronc Spray Control (DESC) Sprayng technque Handlng the hgh-pressure hose Interrupton of work... Contents Page 8. Cleanng the unt (shuttng down) Cleanng unt from outsde Cleanng the hgh-pressure flter Cleanng Arless spray gun Cleanng the nlet screen Remedy n case of faults Servcng General servcng Hgh-pressure hose...6. Repars at the unt...6. Relef valve...6. Inlet and outlet valve...6. Packngs ProSpray.9 connecton dagram...8. Appendx...9. Selecton of tp...9. Servcng and cleanng of Arless hard-metal tps...9. Spray gun accessores Arless tp table... 0/.5 TempSpray....6 Pump-Runner... Accessores for ProSpray Spare parts lst for man assembly...6 Spare parts lst for flud secton...8 Spare parts lst for drve assembly...9 Spare parts lst of flter assembly...0 Spare parts lst for uprght cart...0 Important notes on product lablty... + years guarantee for professonal fnshng... Sales and servce companes... ProSpray.9

4 Safety Regulatons. Safety regulatons for Arless sprayng. Explanaton of symbols used Ths manual contans nformaton that must be read and understood before usng the equpment. When you come to an area that has one of the followng symbols, pay partcular attenton and make certan to heed the safeguard. Attenton Ths symbol ndcates a potental hazard that may cause serous njury or loss of lfe. Important safety nformaton wll follow. Ths symbol ndcates a potental hazard to you or to the equpment. Important nformaton that tells how to prevent damage to the equpment or how to avod causes of mnor njures wll follow. Danger of skn njecton Danger of fre from solvent and pant fumes Danger of exploson from solvent, pant fumes and ncompatble materals Danger of njury from nhalaton of harmful vapors Notes gve mportant nformaton whch should be gven specal attenton. All accessores must be rated at or above the maxmum operatng pressure range of the sprayer. Ths ncludes spray tps, guns, extensons, and hose. HAZARD: Hgh Pressure Hose The pant hose can develop leaks from wear, knkng and abuse. A leak can nject materal nto the skn. Inspect the hose before each use. PREVENTION: Hgh-pressure hoses must be checked thoroughly before they are used. Replace any damaged hgh-pressure hose mmedately. Never repar defectve hgh-pressure hoses yourself! Avod sharp bends and folds: the smallest bendng radus s about 0 cm. Do not drve over the hgh-pressure hose. Protect aganst sharp objects and edges. Never pull on the hgh-pressure hose to move the devce. Do not twst the hgh-pressure hose. Do not put the hgh-pressure hose nto solvents. Use only a wet cloth to wpe down the outsde of the hose. Lay the hgh-pressure hose n such a way as to ensure that t cannot be trpped over. Only use WAGNER orgnal-hgh-pressure hoses n order to ensure functonalty, safety and durablty. HAZARD: EXPLOSION OR FIRE Solvent and pant fumes can explode or gnte. Severe njury and/or property damage can occur. HAZARD: Injecton njury Attenton: Danger of njury by njecton! A hgh pressure stream produced by ths equpment can perce the skn and underlyng tssues, leadng to serous njury and possble amputaton. Do not treat a sprayng njury as a harmless cut. In case of njury to the skn through coatng materals or solvents, consult a doctor mmedately for quck and expert treatment. Inform the doctor about the coatng materal or solvent used. PREVENTION: NEVER am the gun at any part of the body. NEVER allow any part of the body to touch the flud stream. DO NOT allow body to touch a leak n the flud hose. NEVER put your hand n front of the gun. Gloves wll not provde protecton aganst an njecton njury. ALWAYS lock the gun trgger, shut the flud pump off and release all pressure before servcng, cleanng the tp guard, changng tps, or leavng unattended. Pressure wll not be released by turnng off the engne. The PRIME/SPRAY valve or pressure bleed valve must be turned to ther approprate postons to releve system pressure. ALWAYS keep tp guard n place whle sprayng. The tp guard provdes some protecton but s manly a warnng devce. ALWAYS remove the spray tp before flushng or cleanng the system. NEVER use a spray gun wthout a workng trgger lock and trgger guard n place. PREVENTION: Do not use materals wth a flashpont below C (70 F). Flashpont s the temperature at whch a flud can produce enough vapors to gnte. Do not use the unt n work places whch are cove by the exploson protecton regulatons. Provde extensve exhaust and fresh ar ntroducton to keep the ar wthn the spray area free from accumulaton of flammable vapors. Avod all gnton sources such as statc electrcty sparks, electrcal applances, flames, plot lghts, hot objects, and sparks from connectng and dsconnectng power cords or workng lght swtches. Do not smoke n spray area. Place sprayer suffcent dstance from the spray object n a well ventlated area (add more hose f necessary). Flammable vapors are often heaver than ar. Floor area must be extremely well ventlated. The pump contans arcng parts that emt sparks and can gnte vapors. The equpment and objects n and around the spray area must be properly grounded to prevent statc sparks. Use only conductve or earthed hgh pressure flud hose. Gun must be earthed through hose connectons. Power cord must be connected to a grounded crcut (electrc unts only). Always flush unt nto separate metal contaner, at low pump pressure, wth spray tp removed. Hold gun frmly aganst sde of contaner to ground contaner and prevent statc sparks. 4 ProSpray.9

5 Follow materal and solvent manufacturer s warnngs and nstructons. Be famlar wth the coatng materal s MSDS sheet and techncal nformaton to ensure safe use. Use lowest possble pressure to flush equpment. When cleanng the unt wth solvents, the solvent should never be sprayed or pumped back nto a contaner wth a small openng (bunghole). An explosve gas/ar mxture can arse. The contaner must be earthed. HAZARD: HAZARDOUS VAPORS Pants, solvents, and other materals can be harmful f nhaled or come n contact wth body. Vapors can cause severe nausea, fantng, or posonng. PREVENTION: Wear respratory protecton when sprayng. Read all nstructons suppled wth the mask to be sure t wll provde the necessary protecton. All local regulatons regardng protecton aganst hazardous vapors must be observed. Wear protectve eyewear. Protectve clothng, gloves and possbly skn protecton cream are necessary for the protecton of the skn. Observe the regulatons of the manufacturer concernng coatng materals, solvents and cleanng agents n preparaton, processng and cleanng unts. HAZARD: GENERAL Ths product can cause severe njury or property damage. PREVENTION: Follow all approprate local, state, and natonal codes governng ventlaton, fre preventon, and operaton. Pullng the trgger causes a recol force to the hand that s holdng the spray gun. The recol force of the spray gun s partcularly powerful when the tp has been removed and a hgh pressure has been set on the arless pump. When cleanng wthout a spray tp, set the pressure control knob to the lowest pressure. Use only manufacturer authorzed parts. User assumes all rsks and labltes when usng parts that do not meet the mnmum specfcatons and safety devces of the pump manufacturer. ALWAYS follow the materal manufacturer s nstructons for safe handlng of pant and solvents. Clean up all materal and solvent splls mmedately to prevent slp hazard. Wear ear protecton. Ths unt can produce nose levels above 85 db(a). Never leave ths equpment unattended. Keep away from chldren or anyone not famlar wth the operaton of arless equpment. Devce weghs n excess of 6 kg. Three-person lft s requ. Do not spray on wndy days. The devce and all related lquds (.e. hydraulc ol) must be dsposed of n an envronmentally frendly way. Safety regulatons. Electrc Safety Electrc models must be earthed. In the event of an electrcal short crcut, earthng uces the rsk of electrc shock by provdng an escape wre for the electrc current. Ths product s equpped wth a cord havng an earthng wre wth an approprate earthng plug. Connecton to the mans only through a specal feed pont, e.g. through an error protecton nsallaton wth INF < 0 ma. DANGER Work or repars at the electrcal equpment may only be car out by a sklled electrcan. No lablty s assumed for ncorrect nstallaton. Swtch the unt off. Before all repar work, unplug the power plug from the outlet. Danger of short-crcuts caused by water ngressng nto the electrcal equpment. Never spray down the unt wth hgh-pressure or hghpressure steam cleaners. Work or repars at the electrcal equpment: These may only be car out by a sklled electrcan. No lablty s assumed for ncorrect nstallaton.. Electrostatc chargng (formaton of sparks or flames) Electrostatc chargng of the unt may occur durng sprayng due to the flow speed of the coatng materal. These can cause sparks and flames upon dscharge. The unt must therefore always be earthed va the electrcal system. The unt must be connected to an approprately-grounded safety outlet. An electrostatc chargng of spray guns and the hgh-pressure hose s dscharged through the hgh-pressure hose. For ths reason the electrc resstance between the connectons of the hgh-pressure hose must be equal to or lower than MΩ. ProSpray.9 5

6 General vew of applcaton. General vew of applcaton. Applcaton Descrpton of unt = Recommended = Not-recommended Model Materals Object Sze PS. PS. PS.5 PS.9 PS. PS.4 PS.9 Release agents, ols, undercoats, prmers, fllers, synthetc resn-based pants, acrylc pants recommended nozzle sze: FneFnsh up to 00 m 00 m m more than 800 m up to 00 m 00 m m more than 800 m up to 00 m 00 m m more than 800 m up to 00 m 00 m m more than 800 m Emulson pants, latex pants recommended nozzle sze: Ant-corrosve agents, flame retardants, fabrc adhesve recommended nozzle sze: Arless-scrapers recommended nozzle sze: Coatng materals Processble coatng materals Pay attenton to the Arless qualty of the coatng materals to be processed. Dlutable lacquers and pants or those contanng solvents, twocomponent coatng materals, dspersons, latex pants. No other materals should be used for sprayng wthout WAGNER s approval. Flterng Despte sucton flter and nserton flter n the spray gun, flterng of the coatng materal s generally advsable. Str coatng materal before commencement of work. Attenton: Make sure, when strrng up wth motordrven agtators that no ar bubbles are str n. Ar bubbles dsturb when sprayng and can, n fact, lead to nterrupton of operaton. Vscosty Wth ths unt t s possble to process hghly vscous coatng materals of up to around MPa s. If hghly vscous coatng materals cannot be taken n by sucton, they must be dluted n accordance wth the manufacturer s nstructons. Two-component coatng materal The approprate processng tme must be adhe to exactly. Wthn ths tme rnse through and clean the unt metculously wth the approprate cleanng materals.. Descrpton of unt. Arless process The man areas of applcaton are thck layers of hghly vscous coatng materal for large areas and a hgh consumpton of materal. A pston pump takes n the coatng materal by sucton and conveys t to the tp. Pressed through the tp at a pressure of up to a maxmum of bar (, MPa), the coatng materal s atomsed. Ths hgh pressure has the effect of mcro fne atomsaton of the coatng materal. As no ar s used n ths process, t s descrbed as an AIRLESS process. Ths method of sprayng has the advantages of fnest atomsaton, cloudless operaton and a smooth, bubble-free surface. As well as these, the advantages of the speed of work and convenence must be mentoned.. Functonng of the unt In the followng there s a short descrpton of the techncal constructon for better understandng of the functon. WAGNER ProSpray unts are electrcally drven hgh-pressure sprayng unts. A gear unt transfers the drvng force to a crankshaft. The crankshaft moves the pstons of the materal feed pump up and down. The nlet valve s opened automatcally by the upwards movement of the pston. The outlet valve s opened when the pston moves downward. The coatng materal flows under hgh pressure through the hghpressure hose to the spray gun. When the coatng materal exts from the tp t atomzes. The pressure regulator controls the volume and the operatng pressure of the coatng materal. Coatng materals wth sharp-edged addtonal materals These have a strong wear and tear effect on valves, hgh-pressure hose, spray gun and tp. The durablty of these parts cane be uced apprecably through ths. 6 ProSpray.9

7 . Legend for explanatory dagram ProSpray.9 Spray gun Hose to hose whp connector (/8 x / ) Whp hose to gun connector (/4 x /8 ) 4 Hgh pressure hose, mm x 5 m (/ x 50 ft) 5 Hgh pressure whp hose, 0 mm x.5 m (/8 x 8 ft) 6 Ol cup for EasyGlde (EasyGlde prevents ncreased wear of the packngs) 7 Ol level gauge 8 Pal hook 9 Ol button.4 Explanatory dagram ProSpray.9 0 Sucton tube Return hose Cart Relef valve Lever poston vertcal PRIME ( k crculaton) Lever poston horzontal SPRAY ( p) 4 Dgtal Electronc Spray Control (DESC) 5 Control panel ndcators 6 Pressure control knob 7 ON/OFF swtch Descrpton of unt ProSpray.9 7

8 Descrpton of unt.5 Techncal data Voltage: Max. current consumpton: Power cord: Acceptance capacty: Max. operatng pressure: 0-40 Volt AC, 50/60 Hz 9.5 0VAC x.5 mm 6 m 650 Watt bar (, MPa) Volume flow at MPa (0 bar) wth water: 5.0 l/mn Max tp sze: 0.09 nch 0.99 mm Max. temperature of the coatng materal: 4 C Max vscosty: MPa s Weght: 50 kg Specal hgh-pressure hose: DN mm, 5 m, connecton thread M 6 x.5 Whp hose: DN 0 mm,,5 m, connecton thread M 6 x.5 Dmensons (L X W X H): 6 x 568 x 74 mm Max sound pressure level: 80 db (A) *.8 Pant materal setup Ths sprayer comes wth a flter assembly nstalled. If you plan to spray wth untextu pantng materals, leave the flter nstalled..9 Textu materal setup Ths sprayer comes wth a flter plug that should be put n place of the flter whenever sprayng textu materals. Follow these steps to remove the flter and nstall the plug.. Loosen and remove the flter housng () by hand.. Remove the adapter sprng (), flter (), bearng rng (4) and sprng (5) from the housng (7).. Make sure the O-rng (6) s stll n place. Thread the flter plug (8) nto the housng untl secure. The flter plug should be hand-tghtened, but make sure t s seated fully nto the flter housng. * Place of measurng: m n dstance from the unt and.6 m above the floor, MPa (0 bar) operatng pressure, reverberant floor..6 Transportaton Pushng or pullng the unt Pull out the handle (Fg., Item ) untl t wll come no further. Insert the handle push the buttons () on the spars, and then push n the handle Transportaton n vehcle Secure the unt wth a sutable fastenng. If If usng ths sprayer wth textu materals, t s mportant that the flter nsde of the spray gun be removed. See secton 8.. the sprayer wll be used for sprayng textu products, removal of the nlet screen n the foot valve may be necessary. Ths wll allow proper prmng and flow of the textu product. See secton ProSpray.9

9 4. Startng operaton 4. Hgh-pressure hose, spray gun and separatng ol. Screw the 5 m hgh-pressure hose () to the coatng materal outlet (Fg. 4, Item ).. Thread the double fttng nto the other end of the hghpressure hose.. Thread the whp hose (4) onto the remanng exposed end of the double fttng. 4. Thread the whp hose / gun connector onto the gun nlet (). 5. Screw the spray gun wth the selected tp onto the.5 m hghpressure whp hose. 6. Tghten the unon nuts at the hgh-pressure hoses frmly so that coatng materal does not leak. Startng operaton Control Panel Indcators The followng s a descrpton of the control panel ndcators. Servce Indcator Pressure Indcator Pressure Indcator The pressure ndcator shows the current operatng pressure of the sprayer. It has three dfferent ndcatons: blnkng yellow, sold yellow, and sold. 7. Remove the ol cup cap wth a straght-slot screwdrver. 8. Fll the ol cup wth EasyGlde (Fg. 5) untl the ol gauge (4) s showng that t s full. Attenton EasyGlde prevents ncreased wear and tear to the packngs. 9. Replace ol cup cap. 0. Press ol button -5 tmes to prme the oler. Press once for every eght hours of usage to lubrcate the flud secton. Blnkng Yellow When the pressure ndcator s blnkng yellow, the sprayer s operatng between 0 and.4 MPa (4 bar). A blnkng yellow pressure ndcator means: The sprayer s plugged n and turned ON The sprayer s at prmng pressure (lttle or no pressure) It s safe to move the relef valve between postons It s safe to change or replace the spray tp If the pressure ndcator begns blnkng yellow when the pressure control knob s set at a hgher pressure and the relef valve s n the SPRAY poston, ether the spray tp s worn or the sprayer s n need of servce/repar. Sold Yellow When the pressure ndcator s sold yellow, the sprayer s operatng between.4 MPa (4 bar) and MPa (0 bar). A sold yellow pressure ndcator means: The sprayer s at the proper pressure settng for sprayng stan, lacquer, varnsh, and mult-colors ProSpray.9 9

10 Startng operaton Sold Green When the pressure ndcator s sold, the sprayer s operatng between MPa (0 bar) and MPa (0 bar). A sold pressure ndcator means: The sprayer s at the proper pressure settng for sprayng olbased and latex house pants The sprayer s operatng at peak performance at a hgh pressure settng If the pressure ndcator goes to sold yellow when the pressure s set so that t starts at sold, t ndcates one of the followng: a. Tp Wear Indcator when sprayng wth latex or at hgh pressure the sold yellow appears. Ths means the tp s worn and needs to be replaced. b. Tp Too Large when a tp that s too large for the sprayer s put n the gun, the pressure ndcator wll turn from sold to sold yellow. c. Flud Secton Wear f a sold yellow pressure ndcator appears when usng a new tp and the pressure s set at maxmum, servce may be requ (worn packngs, worn pston, stuck valve, etc...). Servce Indcator The Servce ndcator s on when the motor s commanded to run. Ths ndcator s used by servce centers to troubleshoot motor problems. 4. Pressure control knob settngs (Fg. 7). Mnmum pressure settng. Black zone no pressure generaton. Blue zone pulsatng pressure for cleanng 4.5 Cleanng preservng agent when startng-up of operaton ntally. Immerse the sucton tube (Fg. 8, Item ) and return hose () nto a contaner wth a sutable cleanng agent.. Turn the pressure control knob counterclockwse () to mnmum pressure.. Open the relef valve (4), valve poston PRIME (k crculaton). 4. Swtch the unt (5) ON. 5. Wat untl the cleanng agent exudes from the return hose. 6. Close the relef valve, valve poston SPRAY (p spray). 7. Pull the trgger of the spray gun. 8. Spray the cleanng agent from the unt nto an open collectng contaner Connecton to the mans network Attenton The unt must be connected to an appropratelygrounded safety outlet. Before connectng the unt to the mans supply, ensure that the lne voltage matches that specfed on the unt s ratng plate. The connecton must be equpped wth a resdual current protectve devce wth INF 0 ma. 4.6 Takng the unt nto operaton wth coatng materal. Immerse the sucton tube (Fg. 8, Item ) and return hose () nto the coatng materal contaner.. Turn the pressure control knob counterclockwse () to mnmum pressure.. Open the relef valve (4), valve poston PRIME (k crculaton). 4. Swtch the unt (5) ON. 5. Wat untl the coatng materal exudes from the return hose. 6. Close the relef valve, valve poston SPRAY (p spray). 7. Trgger the spray gun several tmes and spray nto a collectng contaner untl the coatng materal exts the spray gun wthout nterrupton. 8. Increase the pressure by slowly turnng up the pressure control knob. Check the spray pattern and ncrease the pressure untl the atomzaton s correct. Always turn the pressure control knob to the lowest settng wth good atomzaton. 9. The unt s ready to spray. 0 ProSpray.9

11 Startng operaton 4.7 Dgtal Electronc Spray Control (DESC) The Dgtal Electronc Spray Control (DESC) ncreases the functonalty of the sprayer. It s nstalled drectly below the pressure control knob on the control panel. It conssts of a dsplay and four functon keys. The dsplay shows varous menu screens that allow the user to customze and montor sprayer operaton usng the functon keys. The Dsplay Functon Keys SET MPa.0 ACTUAL MPa.5 pressure control knob overrdes the Dgtal Electronc Spray Control (DESC) settngs. Anytme the pressure control knob s turned, the sprayer pressure wll change accordngly. Functon Keys The functon keys are numbe 4. Each key s labeled wth an addtonal functon as well. #/Menu Key Pressng the # key scrolls through the avalable menu screens or performs a functon descrbed on the actve menu screen. #/g Key Pressng the # key performs a functon descrbed on the actve menu screen or ncreases a value. #/h Key Pressng the # key performs a functon descrbed on the actve menu screen or decrease a value. #4/Select Key Pressng the #4 key selects the actve menu screen or performs a functon descrbed on the actve menu screen. Menu Screens Several menu screens are avalable for the user to customze and montor sprayer operaton. They nclude Man Screen, Volume Pumped, Job Volume, Unt Seral #, Tmers, Job Tmers, Servce Tme, Securty Code, Prme, and Rapd Clean. Man Screen The Man Screen s the default screen for SET MPa.0 the control system at sprayer startup. ACTUAL MPa.5 Pressng the # key swtches between PSI, Bar and MPa unts of measure. Press the # key to scroll through the remanng menu screens. For sprayers equpped wth an nne-language Dgtal Electronc Spray Control (DESC): Pressng the # key at the Man Screen swtches between PSI, Bar and MPa unts of measure. Pressng the # key at the Man Screen changes the language of the text on the dsplay. There are a total of nne languages avalable. Each tme the # key s pressed, a dfferent language wll appear. The languages, n order of appearance, are: Englsh, Spansh, Dutch, Dansh, Swedsh, German, French, Italan, and Portuguese. Volume Pumped Screen The Volume Pumped screen shows the total number of gallons or lters sprayed by the sprayer. To select the Volume Pumped screen, press the #4 key. Job Volume Screen The Job Volume screen allows the user to reset a lter counter to track usage on specfc jobs. To select the Job Volume screen, press the #4 key. Unt Seral # Screen The Unt Seral # screen shows the sprayers seral number. To select the Unt Seral # screen, press the #4 key. VOLUME PUMPED MENU- SELECT-4 GALLONS MENU- LITRES MENU- X LITRES- X GALLONS- JOB VOLUME MENU- SELECT-4 GALLONS MENU- XXXX RESET- UNIT SERIAL # MENU- SELECT-4 SER # XXXXXXXXXX MENU- Tmers Screen The Tmers screen shows the total tme the TIMERS sprayer has been turned on as well as the MENU- SELECT-4 total tme the sprayer has been runnng (pumpng). To select the Tmers screen, press the #4 key. ON TIME RUN TIME XXXX XXXX Job Tmers Screen The Job Tmers screen allows the user to JOB TIMERS reset the ON TIME and RUN TIME to MENU- SELECT-4 track tme on specfc jobs. To select the Job Tmers screen, press the JOB ON X MENU- RESET- #4 key. JOB ON screen wll appear. Press # to reset. Press # to contnue to JOB JOB RUN X RUN screen. Press # to reset. Press # MENU- RESET- to scroll through the remanng menu screens. Servce Tme Screen The Servce Tme screen allows the user to set a servce tme nterval (n hours). Below SERVICE TIME MENU- SELECT-4 the set tme, the screens shows the current amount of hours on the sprayer snce the last actvaton of the servce tmer. To select the Servce Tmer screen, press the #4 key. To set the servce tme, press the # (up) and/or the # (down) keys to the des RUN HOURS XX XX tme (run hours wll ncrease/decrease n ncrements of 5 for each tme you press a key). When the servce tme nterval s set and met by the run hours, the dsplay wll show a Servce Requ screen. The pump wll reman functonal. To return to the Man Screen, press the # key. Dong so wll reset the and Run Hours dsplayed on the Servce Screen back to 0. ProSpray.9

12 Startng operaton Securty Code Screen The Securty Code screen allows the user to set a four dgt securty code to prevent SECURITY CODE MENU- CHANGE- unauthorzed use of the sprayer. If a securty code has been set, the control system dsplay wll ask for the code at startup. If the correct code s ente, the dsplay wll show the Man Screen and the sprayer wll operate. If the wrong code s ente, the dsplay wll contnue to ask for the correct code and the sprayer wll be dsabled. To set or change the securty code, press the # key. 5. Sprayng technque Sprayng technque Injecton hazard. Do not spray wthout the tp guard n place. NEVER trgger the gun unless the tp s completely turned to ether the spray or the unclog poston. ALWAYS engage the gun trgger lock before removng, replacng or cleanng tp. If the sprayer s new, no securty code s set and the Man Screen wll appear at startup. When settng a securty code for the frst tme, the Enter Old Code Number screen wll appear, and you wll need to enter. Enter the old securty code number to access the screen that allows the code ENTER OLD CODE NUMBER change. If the wrong code s ente, the dsplay wll contnue to ask for the correct code and the securty code cannot be changed. Enter the new securty code. Once the new code s ente, the dsplay wll automatcally ask that the new code be re-ente for verfcaton. If the same new code s re-ente, the dsplay wll confrm that the new code has been accepted and return to the Man Screen. If the new code ENTER NEW CODE NUMBER XXXX RE-ENTER NEW NUMBER XXXX NEW CODE NUMBER ACCEPTED s re-ente ncorrectly, the dsplay wll return to the Enter New Code Number screen and the process wll repeat. If you forget or msplace your securty code, you can contact Wagner customer servce for assstance. The key to a good pant job s an even coatng over the entre surface. Keep your arm movng at a constant speed and keep the spray gun at a constant dstance from the surface. The best sprayng dstance s 5 to 0 cm between the spray tp and the surface. 5-0 cm Keep the spray gun at rght angles to the surface. Ths means movng your entre arm back and forth rather than just flexng your wrst. To nactvate the securty functon, enter at the Enter New Code Number screen (ths s the default code that leaves the sprayer unlocked). As a result, the Man Screen wll appear at sprayer startup. Prme Screen The Prme screen appears when the pressure control knob s set at the MIN settng. PRIME Rapd Clean Screen The Rapd Clean screen appears when the RAPID CLEAN pressure control knob s set at the RAPID CLEAN poston and the PRIME/SPRAY valve s n the PRIME poston. If there s no acton at any menu screen for 0 seconds, the dsplay wll go back to the Man Screen. Keep the spray gun perpendcular to the surface, otherwse one end of the pattern wll be thcker than the other. Trgger gun after startng the stroke. Release the trgger before endng the stroke. The spray gun should be movng when the trgger s pulled and released. Overlap each stroke by about 0%. Ths wll ensure an even coatng. 5-0 cm 5-0 cm If very sharp edges result or f there are streaks n the spray jet ncrease the operatng pressure or dlute the coatng materal. ProSpray.9

13 Handlng the hgh-pressure hose 6. Handlng the hgh-pressure hose The unt s equpped wth a hgh-pressure hose specally suted for pston pumps. Danger of njury through leakng hgh-pressure hose. Replace any damaged hgh-pressure hose mmedately. Never repar defectve hgh-pressure hoses yourself! The hgh-pressure hose s to be handled wth care. Avod sharp bends and folds: the smallest bendng radus s about 0 cm. Do not drve over the hgh-pressure hose. Protect aganst sharp objects and edges. Never pull on the hgh-pressure hose to move the devce. Make sure that the hgh-pressure hose cannot twst. Ths can be avoded by usng a Wagner spray gun wth a swvel jont and a hose system. When usng the hgh-pressure hose whle workng on scaffoldng, t s best to always gude the hose along the outsde of the scaffoldng. The rsk of damage rses wth the age of the hghpressure hose. Wagner recommends replacng hghpressure hoses after 6 years. Use only WAGNER orgnal-hgh-pressure hoses n order to ensure functonalty, safety and durablty. 7. Interrupton of work. Open the relef valve, valve poston PRIME (k crculaton).. Swtch the unt OFF.. Turn the pressure control knob counterclockwse to mnmum pressure. 4. Pull the trgger of the spray gun n order to release the pressure from the hgh-pressure hose and spray gun. 5. Secure the spray gun, refer to the operatng manual of the spray gun. 6. If a standard tp s to be cleaned, see Page 9, Secton.. If a non-standard tp s nstalled, proceed accordng to the relevant operatng manual. 7. Dependng on the model, leave the sucton tube or the sucton hose and return hose mmersed n the coatng materal or swvel or mmerse t nto a correspondng cleanng agent. Cleanng the unt (shuttng down) 8. Cleanng the unt (shuttng down) A clean state s the best method of ensurng operaton wthout problems. After you have fnshed sprayng, clean the unt. Under no crcumstances may any remanng coatng materal dry and harden n the unt. The cleanng agent used for cleanng (only wth an gn ton pont above C) must be sutable for the coatng materal used. Secure the spray gun, refer to the operatng manual of the spray gun. Clean and remove tp. For a standard tp, refer to Page 9, Secton.. If a non-standard tp s nstalled, proceed accordng to the relevant operatng manual.. Remove sucton hose from the coatng materal.. Close the relef valve, valve poston SPRAY (p spray).. Swtch the unt ON. 4. Pull the trgger of the spray gun n order to pump the remanng coatng materal from the sucton hose, hghpressure hose and the spray gun nto an open contaner. Attenton The contaner must be earthed n case of coatng materals whch contan solvents. Cauton! Do not pump or spray nto a contaner wth a small openng (bunghole)! Refer to the safety regulatons. 5. Immerse sucton hose wth return hose nto a contaner wth a sutable cleanng agent. 6. Turn the pressure control knob nto the blue zone - pulsatng pressure for unt cleanng. 7. Open the relef valve, valve poston PRIME (k crculaton). 8. Pump a sutable cleanng agent n the crcut for a few mnutes. 9. Close the relef valve, valve poston SPRAY (p spray). 0. Pull the trgger of the spray gun.. Pump the remanng cleanng agent nto an open contaner untl the unt s empty.. Swtch the unt OFF. 8. Cleanng unt from outsde Frst of all pull out mans plug from socket. Attenton If fast-dryng or two-component coatng materal s used, ensure that the unt s rnsed wth a sutable cleanng agent wthn the processng tme. Attenton Danger of short crcult through panetratng water! Never spray down the unt wth hgh-pressure or hgh-pressure steam cleaners. Attenton Do not put the hgh-pressure hose nto solvents. Use only a wet cloth to wpe down the outsde of the hose. Wpe down unt externally wth a cloth whch has been mmersed n a sutable cleanng agent. ProSpray.9

14 Cleanng the unt (shuttng down) 8. Cleanng the hgh-pressure flter Clean the flter cartrdge regularly. A soled or clogged hgh-pressure flter can cause a poor spray pattern or a clogged tp.. Turn the pressure regulator knob nto the black zone untl t stops (no pressure).. Open the relef valve, valve poston PRIME (k crculaton).. Swtch the unt OFF. Unplug the power plug from the outlet. 4. Unscrew the flter housng (Fg. 0, Item ). wth a strap wrench. 5. Pull the flter cartrdge () from the bearng sprng (). 6. Clean all the parts wth the correspondng cleanng agent. If necessary, replace the flter cartrdge. 7. Check the O-rng (4), replace t f necessary. 8. Place the bearng rng (5) aganst the bearng sprng (). Slde the flter cartrdge () over the bearng sprng. 9. Screw n flter housng () and tghten t as far as possble wth the strap wrench. 8. Cleanng Arless spray gun. Rnse Arless spray gun wth an approprate cleanng agent.. Clean tp thoroughly wth approprate cleanng agent so that no coatng materal resdue remans.. Thoroughly clean the outsde of the Arless spray gun. Intake flter n Arless spray gun Dsassembly (Fg. ). Pull protectve guard () forward vgorously.. Screw grp () out of the gun housng. Remove ntake flter ().. Intake flter congested or defectve replace. Assembly. Place ntake flter () wth the long cone nto the gun housng.. Screw n grp () nto the gun housng and tght en.. Slot n protectve guard (). 50 bar max.600 ps Warnng: keep clear of tp Cleanng the nlet screen The nlet screen wll clog and must be cleaned at least once a day.. Remove the retanng rng () from the foot valve () housng.. Remove the nlet screen () from the foot valve housng ().. Clean thoroughly wth the approprate solvent. 4 ProSpray.9

15 9. Remedy n case of faults Remedy n case of faults Type of malfuncton A. Unt does not start Possble cause. No voltage appled.. Pressure settng too low.. ON/OFF swtch defectve. Measures for elmnatng the malfuncton. Check voltage supply.. Turn up pressure control knob.. Replace. B. Unt does not draw n materal. Relef valve s set to SPRAY (p spray).. Flter projects over the flud level and sucks ar.. Flter clogged. 4. Sucton hose/sucton tube s loose,.e. the unt s suckng n outsde ar.. Set relef valve to PRIME (k crculaton).. Refll the coatng materal.. Clean or replace the flter. 4. Clean connectng ponts. Tghten sucton tube. C. Unt draws n materal, but the pressure does not buld up. Tp heavly worn.. Tp too large.. Pressure settng too low. 4. Flter clogged. 5. Coatng materal flows through the return hose when the relef valve s n the SPRAY (p spray) poston. 6. Packngs stcky or worn. 7. Valve balls worn. 8. Valve seats worn.. Replace. For selecton of a smaller tp, see Tp table on Page 0.. Turn pressure control knob clockwse to ncrease. 4. Clean or replace the flter. 5. Remove and clean or replace relef valve. 6. Remove and clean or replace packngs. 7. Remove and replace valve balls. 8. Remove and replace valve seats. D. Coatng materal exts at the top of the flud secton. Upper packng s worn.. Pston s worn.. Remove and replace packng.. Remove and replace pston. E. Increased pulsaton at the spray gun. Incorrect hgh-pressure hose type.. Tp worn or too large.. Pressure too hgh.. Only use WAGNER orgnal-hgh-pressure hoses n order to ensure functonalty, safety and durablty.. Replace tp.. Turn pressure control knob to a lower number. F. Poor spray pattern. Tp s too large for the coatng materal whch s to be sprayed.. Pressure settng ncorrect.. Volume too low. 4. Coatng materal vscosty too hgh.. Replace tp, see Tp table on Page 0.. Turn pressure control knob untl a satsfactory sprayng pattern s acheved.. Clean or replace all flters. 4. Thn out accordng to the manufacturer s nstructons. G. Unt loses power. Pressure settng too low.. Turn pressure control knob clockwse to ncrease. Dgtal Electronc Spray Control (DESC) Error Messages The followng error message screens appear whenever the Dgtal Electronc Spray Control (DESC) detects a problem wth the sprayer. Once a problem occurs and the error message appears, the sprayer wll shut down. Before proceedng, releve any pressure remanng n the system (valve poston PRIME k). Addtonally, follow all other warnngs to uce the rsk of an njecton njury, njury from movng parts or electrc shock. Always unplug the sprayer before servcng! Low Voltage Screen The Low Voltage screen appears when the sprayer shuts down because of low nput voltage. Check the power supply and correct the problem. Restart the sprayer. Hgh Motor Temperature Screen The Hgh Motor Temperature screen appears when the temperature of the motor has rsen too hgh. Take the sprayer to a Wagner authorzed servce center for repar. LOW VOLTAGE HIGH MOTOR TEMPERATURE Check Transducer Screen The Check Transducer screen appears when the transducer has become dsconnected or s defectve. Take the sprayer to a Wagner authorzed servce center for repar. Check Motor Screen The Check Motor screen appears when the motor or motor sensor s defectve. Take the sprayer to a Wagner authorzed servce center for repar. CHECK TRANSDUCER CHECK MOTOR Hgh Control Temperature Screen The Hgh Control Temperature screen appears HIGH CONTROL when the temperature of the Dgtal Electronc TEMPERATURE Spray Control (DESC) has rsen too hgh. Take the sprayer to a Wagner authorzed servce center for repar. Hgh Mechancal Load The Hgh Mechancal Load screen appears when HIGH MECHANICAL the sprayer shuts down because of hgh current LOAD or when the sprayer goes nto current fold back mode. Take the sprayer to a Wagner authorzed servce center for repar. ProSpray.9 5

16 Servcng 0. Servcng 0. General servcng Servcng of the unt should be car out once annually by the WAGNER servce.. Check hgh-pressure hoses, devce connectng lne and plug for damage.. Check the nlet valve, outlet valve and flter for wear. 0. Hgh-pressure hose Inspect the hgh-pressure hose vsually for any notches or bulges, n partcular at the transton n the fttngs. It must be possble to turn the unon nuts freely. The rsk of damage rses wth the age of the hghpressure hose. Wagner recommends replacng hghpressure hoses after 6 years.. Repars at the unt Swtch the unt OFF. Before all repar work: Unplug the power plug from the outlet.. Relef valve. Use a drft punch of mm to remove the grooved pn (Fg., Item ) from the relef valve handle ().. Remove the relef valve handle () and cam base ().. Usng a wrench, remove the valve housng (4). 4. Ensure that the seal (5) s seated correctly, then screw the new valve housng (4) completely nto the flter block (6). Tghten securely wth a wrench. 5. Algn the cam base () wth the hole n the flter block (6). Lubrcate the cam base wth grease and slde on the cam base. 6. Brng the hole n the valve shaft (7) and n the relef valve handle () nto algnment. 7. Insert the grooved pn () to secure the relef valve handle n poston. Repars at the unt. Inlet and outlet valve. Remove the four screws n the front cover and then remove the front cover. Danger of crushng - do not reach wth the fngers or tool between the movng parts.. Turn the pressure control knob to mnmum pressure. The Dg-Trac screen should say PRIME.. Press the # key on the Dg-Trac control panel. The CREEP MODE screen wll now appear. 4. Slowly turn the pressure control knob clockwse to ncrease the pressure. The crankshaft/slder assembly wll begn to move very slowly. 5. When t reaches the bottom, dead-center of ts stroke, turn the pressure control knob back to mnmum pressure. The crankshaft/slder assembly should stop. 6. Unplug the power plug from the outlet. 7. Pull off clamp on sucton tube and remove return hose. 8. Unscrew the connecton hose (Fg. 4, tem ) from the hghpressure flter. 9. Turn the knob on the sde of the cart clockwse to unlock the cart. Tlt the cart backwards untl t locks nto place. 0. Loosen and remove the nlet valve housng () from the upper housng.. Remove bearng rng (), O-rng (4), O-rng (5), nlet valve seat (6), nlet valve ball (7) and upper ball gude (8).. Clean all the parts wth the correspondng cleanng agent. Check the nlet valve housng (), nlet valve seat (6) and nlet valve ball (7) for wear and replace the parts f necessary. If the worn nlet valve seat (6) s unused on one sde, nstall t the other way around Screw out outlet valve housng (Fg 5, tem 9) from the pston (0) wth /8 nch hexagon socket head wrench. 4. Remove the upper seal (), upper ball gude (), outlet valve ball (), washer (4) and outlet valve seatng (5). 6 ProSpray.9

17 Repars at the unt 5. Clean all the parts wth the correspondng cleanng agent. Check outlet valve housng (9), outlet valve seat (5), outlet valve ball () and upper ball gude () for wear and replace parts f necessary. If the worn outlet valve seat (5) s unused on one sde, nstall t the other way around. 6. Carry out nstallaton n the reverse order. 7. If you plan to replace the flud secton packngs, move on to secton.. If not, reassemble flud secton n the reverse order of how t was dsassembled. 4. Remove the adapter () and lower packng assembly () from the bottom of the upper housng. Be careful not to scratch, score, or otherwse damage the upper housng durng removal of the packngs Packngs. Remove nlet valve housng n accordance wth the steps n Chapter., Page 6.. It s not necessary to remove the outlet valve.. Pull the lever on the undersde of the sprayer toward the front of the sprayer. Ths wll un-clamp the entre flud secton. 4. Slde the flud secton forward to remove t from the gear housng. 5. Place the flud secton cylnder uprght n a vse by clampng on the wrench flats (Fg. 6, Item ) Do not over-tghten the vse. Damage to the cylnder may occur. 6. Turn the upper housng () counterclockwse to loosen t from the cylnder (). 7. Slowly pull down the upper housng () just far enough to expose the extenson slder (4) and the connectng pn (5) that connects the pston rod (6) to the extenson slder (4). 8. Push the connectng pn out of the extenson slder and pston rod and remove the pston rod and upper housng. 9. Place the upper housng uprght n a vse by clampng on the wrench flats (7). Do not over-tghten the vse. Damage to the upper housng may occur. 0. Usng a wrench, remove the upper seal retaner (Fg. 6, Item 8).. Slde the pston rod (6) out through the bottom of the upper housng ().. Inspect the pston rod (6) for wear and replace f necessary.. Remove the upper support rng (9) and upper packng assembly (0) from the top of the upper housng () Clean the upper housng () and cylnder (-5). Inspect the upper housng and cylnder for damage and replace f necessary. 6. Place the upper housng uprght () n a vse by clampng on the wrench flats (7). 7. Locate the new upper and lower packngs and remove the pre-form tools. Save the upper packng pre-form tool for use as the pston nserton tool later n ths procedure. Do not remove the pre-form tools from the upper and lower packngs untl mmedately before they are nstalled nto the upper housng. 8. Lubrcate upper packng (0) and lower packng () wth machne grease. ProSpray.9 7

18 Repars at the unt 9. Insert upper packng (Fg. 7) wth O-rng () and protrudng lp () downward. 0. Insert upper support rng (9) on top of the upper packng (0). Thread the upper seal retaner (8) nto the upper housng ().. Rotate the upper housng n the vse so that the bottom end s facng up.. Insert the lower packng (Fg. 8) partally nto the bottom of the cylnder wth the large beveled edge () facng toward the cylnder (beveled edge wll be facng up when the cylnder s uprght). 4. Push the lower packng assembly (Fg. 6, Item ) nto poston usng the lower packng nserton tool (see Flud Secton Assembly parts lst for lower packng nserton tool P/N). Coat the pston nserton tool (.e. upper packng pre-form tool) and the pston rod wth grease before nsertng them nto the upper housng. 5. Place the pston nserton tool over the top of the pston rod (6). 6. Insert the pston rod (6) nto the bottom of the upper housng (), through the lower packng assembly (), through the upper packng assembly (0), and out through the upper seal retaner (8). Make sure the rased lp on the bottom of the lower packng s fully outsde the packng around the pston rod after nserton of the pston rod. 7. Remove the pston nserton tool from the top of the pston rod (6). 8. Lubrcate the threads on the upper housng wth ant-seze compound. Remove the upper housng from the vse. 9. Insert the pston rod nto the extenson slder. When the connectng pn hole on the pston rod lnes up wth the hole n the extenson slder, nsert the connectng pn. 0. Thread the upper housng nto the cylnder, turnng clockwse.. Contnue to turn the upper housng clockwse untl t s flush aganst the cylnder.. Replace the cylnder () back nto the flud secton clamp on the gear housng. Make sure to slde the top of the pston rod extenson nto the T-slot () on the slder assembly (4).. Push the lever on the undersde of the unt toward the rear of the sprayer to lock the flud secton back nto place. 4. Insert the adapter (Fg. 6, tem ) nto the bottom of the upper housng. 5. Makng sure that the bearng rng (Fg. 4, tem ) and O-rngs (Fg. 4, tems 4-5) are lubrcated and n place, reassemble the nlet valve assembly and and thread t nto the upper housng. Tghten the nlet valve housng untl the o-rng engages, then contnue to tghten untl snug. Once snug, tghten an addtonal /8 /4 turn. 6. Replace the connecton hose to the fttng on the hghpressure flter. 7. Replace the return hose nto the clamp on the sphon tube. 8. Install front cover..4 ProSpray.9 connecton dagram Swtch Blue / Whte Black / Brown Ground EMI Flter Blue / Whte Black / Brown Power Cord P/N 0505 P/N 0505 Ground Green / Yellow Blue Whte Blue / Whte Black / Brown Brown Black Green / Yellow Ground Green / Yellow Black Fuse block Red Fuse Black Red (+) Black (-) Capactor Motor controller L.E.D. Fan Blue / Whte Surge suppressor P/N Whte Whte Red Black Motor Hall sensor Potentometer Dsplay wre assembly (P/N 050) Pressure sensor 8 ProSpray.9

19 . Appendx. Selecton of tp To acheve faultless and ratonal workng, the selecton of the tp s of the greatest mportance. In many cases the correct tp can only be determned by means of a sprayng test. Some rules for ths: The spray jet must be even. If streaks appear n the spray jet the sprayng pressure s ether too low or the vscosty of the coatng materal to hgh. Remedy: Increase pressure or dlute coatng materal. Each pump conveys a certan quantty n proporton to the sze of the tp: The followng prncple s vald: large tp = low pressure small tp = hgh pressure There s a large range of tps wth varous sprayng angles. Appendx. Servcng and cleanng of Arless hard-metal tps Standard tps If a dfferent tp type has been ftted, then clean t accordng to manufacturer s nstructons. The tp has a bore processed wth the greatest precson. Careful handlng s necessary to acheve long durablty. Do not forget the fact that the hard-metal nsert s brttle! Never throw the tp or handle wth sharp metal objects. The followng ponts must be observed to keep the tp clean and ready for use:. Turn the relef valve handle fully counterclockwse (k Crculaton).. Swtch off the gasolne engne.. Dsmount the tp from the spray gun. 4. Place tp n an approprate cleanng agent untl all coatng materal resdue s dssolved. 5. If there s pressure ar, blow out tp. 6. Remove any resdue by means of a sharp wooden rod (toothpck). 7. Check the tp wth the help of a magnfyng glass and, f necessary, repeat ponts 4 to 6.. Spray gun accessores Flat jet adjustng tp up to 50 bar (5 MPa Tp markng Bore mm Spray wdth at about 0 cm removal of spray object Pressure 00 bar (0 MPa) Use Flat jet adjustng tp Order No cm Pants cm Pants, fllers cm Pants, dspersons cm Rust protecton pants - dspersons cm Large-area coats Contact protecton for the flat jet adjustment tp Order No Tp extenson wth slewable knee jont (wthout tp) Length: 00 cm Order no Length: 00 cm Order no Length: 00 cm Order no Tp extenson 5 cm, F-thread, Order no cm, G-thread, Order no cm, F-thread, Order no cm, G-thread, Order no cm, F-thread, Order no cm, G-thread, Order no cm, F-thread, Order no cm, G-thread, Order no ProSpray.9 9

20 Appendx.4 Arless tp table Wagner TradeTp tp up to 70 bar (7 MPa) wthout tp F thread (/6-6 UN) for Wagner spray guns Order no wthout tp G thread (7/8-4 UN) for Graco/Ttan spray guns Order no All of the tps n the table below are suppled together wth the approprate gun flter. Applcaton Tp markng Spray angle Bore nch / mm Sprayng wdth mm ) Gun flter Order no. Water-thnnable and solvent-based pants and varnshes, ols, separatng agents / / / / / / / / / / Synthetc-resn pants PVC pants / / / / / / Pants, prmers Fllers / / / / / / / Fllers Rust protecton pants / / / / / / / / yellow yellow yellow yellow yellow yellow yellow yellow Rust protecton pants Latex pants Dspersons / / / / / / / / yellow yellow yellow yellow yellow yellow yellow yellow Rust protecton pants Latex pants Dspersons / / / / / / / / Flame retardant / / / / / / / )Spray wdth at about 0 cm to the object and 00 bar (0 MPa) pressure wth synthetc-resn pant 0 DIN seconds. 0 ProSpray.9

21 Appendx Applcaton Tp markng Spray angle Bore nch / mm Sprayng wdth mm ) Gun flter Order no. Roof coatngs / / / / / / / Thck-flm materals, Corroson protecton Spray fller / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Heavy duty applcatons / / / / / / / / / / / / / / / / / / / / / / / / )Spray wdth at about 0 cm to the object and 00 bar (0 MPa) pressure wth synthetc-resn pant 0 DIN seconds. ProSpray.9

22 Appendx.5 TempSpray The pant materal s heated to the requ temperature unformly by an electrc heatng element, whch s located nsde the hose (regulated from 0 C to C). Advantages: Constant pant temperature even at low outsde temperatures Consderably better workng of hgh vscosty coatng materals Increased applcaton effcency Savngs n solvents due to ucton n vscosty Adaptable to all arless unts Order No Descrpton TempSpray H 6 (deal for lacquer jobs) Basc unt /4 ncl. stanless steel hose, DN6, /4, 0m Spraypack consstng of: basc unt (659), Arless gun AG 4 NPS /4, ncl. Trade Tp nozzler holder (F-thread) and Trade Tp Fne Fnsh 40 TempSpray H 6 (deal for dspersons/materals wth hgh vscosty) Basc unt /4 ncl. Hose reel, heated hose DN0, 5m, hose /4 DN4, m Spraypack consstng of: Basc unt (660), Arless gun AG 4 NPS /4, ncl. Trade Tp nozzler holder (F-thread) and Trade Tp nozzle 49 TempSpray H 6 (deal for dspersons/materals wth hgh vscosty) Basc unt /4 ncl. Hose reel, heated hose DN0, 0m, hose /4 DN4, m Spraypack consstng of: Basc unt (66), Arless gun AG 4 NPS /4, ncl. Trade Tp nozzler holder (F-thread) and Trade Tp nozzle 4 TempSpray H 6 TempSpray H 6 TempSpray H 6 ProSpray.9

23 Appendx.6 Pump-Runner (Order No ) Unversal accessores for cleanng, clean transportaton and preservaton of the pump unt. Features: Smpler cleanng the cleanng lqud crculates constantly through the pump makng thorough cleanng of the nteror No cleanng necessary durng work stoppage or change of locaton because the pant n the pump cannot dry out or leak Better protecton Smple assembly Sutable for the followng models: Daphragm Pumps Double-stroke pston pumps SF SF SF 7 SF SF 7000 Fnsh 70/70 Nespray Deco Nespray PS 4 PS 6 PS 0 PS 4 PS.5 PS.9 PS. PS.4 Order ths at the same tme: EasyClean, cleanng and preservaton agent (8ml) Order no Example of use ProSpray.9

24 Accessores llustraton ProSpray ProSpray.9