Workfit -SR, Dual Monitor Short Surface

Transcription

1 User's Guide Workfit -SR, Dul Monitor Short Surfce Do not throw wy! Crdord locks needed for instlltion. Visit t-sr-instll for instlltion instructionl video. NOTE: 10 feet of cle needed for proper instlltion.extr cles cn e found t For the ltest User Instlltion Guide plese visit: User's Guide - English Guí del usurio - Espñol Mnuel de l utilisteur - Frnçis Geruikersgids - Deutsch Benutzerhnduch - Nederlnds Guid per l utente - Itlino Användrhndok - svensk 用户指南 : 汉语 G-03 rev. E 04/17 Includes Constnt Force Technology 1 of 20

2 Hzrd Symols Review These symols lert users of sfety condition tht demnds ttention. All users should e le to recognize nd understnd the significnce of the following Sfety Hzrds if encountered on the product or within the documenttion. Children who re not le to recognize nd respond ppropritely to Sfety Alerts should not use this product without dult supervision! Symol Signl Word Level of Hzrd NOTE CAUTION WARNING ELECTRICAL A NOTE indictes importnt informtion tht helps you mke etter use of this product. A CAUTION indictes either potentil dmge to hrdwre or loss of dt nd tells you how to void the prolem. A WARNING indictes either potentil for property dmge, personl injury, or deth. An Electricl indictes n impending electricl hzrd which, if not voided, my result in personl injury, fire nd/or deth. Sfety Importnt! You will need to djust this product fter instlltion is complete. Mke sure ll your equipment is properly instlled on the product efore ttempting djustments. This product should move smoothly nd esily through the full rnge of motion nd sty where you set it. If movements re too esy or diffi cult or if product does not sty in desired positions, follow the djustment instructions to crete smooth nd esy movements. Depending on your product nd the djustment, it my tke mny turns to notice difference. Any time equipment is dded or removed from this product, resulting in chnge in the weight of the mounted lod, you should repet these djustment steps to ensure sfe nd optimum opertion. Wrning: Becuse mounting surfce mterils cn vry widely, it is impertive tht you mke sure mounting surfce is strong enough to hndle mounted product nd equipment. Cution: Follow the instructions in this mnul to securely clmp this product to your mounting surfce. Filure to do so my result in equipment dmge or personl injury. Cution: To void the potentil to pinch cles it is importnt to follow the cle routing instructions in this mnul. Filure to follow these instructions my result in equipment dmge or personl injury. CAUTION! Tipping Hzrd. Support the stnd until the clmp is securely tightened. Filure to follow these instructions my result in the stnd tipping over cusing possile equipment dmges nd or personl injury. WARNING STORED ENERGY HAZARD! DO NOT OPEN TOWER OR REMOVE SAFETY GUARD! A primry mechnism within the tower is under tension nd cn e hzrdous to people exposed to it under certin extreme conditions. DO NOT open the tower; DO NOT ttempt to service the crt/stnd. DO NOT remove sfety gurds or lels designed to protect or inform of possile hzrds. Only Ergotron-pproved instllers my service or otherwise modify crt/stnd. Filure to heed this Wrning my result in serious Personl Injury nd Dmge oth to the crt/stnd nd equipment of G-03 rev. E 04/17

3 Fetures & Specifictions 30 5" (127mm) 18.25" (463.55mm) CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! A B C 5-13 ls ( kg) 5-13 ls ( kg) < 5 ls (2.2 kg) A+B < 22 ls (10 kg) Mx Weight Cpcity < 27 ls (12.3 kg) 1 Components A B C D 2 M4 x 8mm 3 M3 x 6mm 4 8x M4 x 6mm 5 2mm 4x M6 x 10mm 4x M6 x 12mm 6 4mm M4 x 10mm 8x 8x 4x M6 x 25mm M4 x 10mm Tools Needed 10mm G-03 rev. E 04/17 3 of 20

4 1 Ly engine down. 2 Attch worksurfce to ottom of riser. NOTE: Mke sure slots lign when instlling work surfce. 4 of G-03 rev. E 04/17

5 1 2 c Screw worksurfce into riser. 4x M6 x 25mm 4mm 3 Disssemle desk clmp. Remove two screws from clmp se. Remove clmp from clmp se. c Mesure desk thickness. d Prtilly reinstll screws into clmp se.(1.5 revolutions) Desk Thickness.4" - 1.4" (10mm - 36mm) 1.1" - 2.4" (28mm - 61mm) G-03 rev. E 04/17 5 of 20

6 1 2 4 Secure clmp se to riser. Mesure desk depth. Bck Front Slide clmp se into ottom of riser. c Secure clmp se to riser. 4mm 4x M6 x 12mm NOTE: Align the clmp window with the line on the ottom of the riser for your desk depth. Desk Depth 30 (76cm) 31 (79cm) 32 ( 81cm) 33 ( 84cm) 34 (86cm) 35 ( 90cm) 36 ( 91cm) 6 of G-03 rev. E 04/17

7 5 Mount to desk. 4mm Two person lift. c Use crdord locks to support worksurfce. Cution: Worksurfce not stle until clmp is secured. d Secure clmp to clmp se G-03 rev. E 04/17 7 of 20

8 e Tighten clmp. Cution: Follow the instructions in this mnul to securely clmp this product to your mounting surfce. Filure to do so my result in equipment dmge or personl injury. NOTE: Push clmp se to edge of mounting surfce. f Remove crdord locks from underneth work surfce 6 Screw crossr to riser. 4mm 4x M6 x 10mm 2" (51mm) 2" (51mm) 2" (51mm) NOTE: Crossr cn e mounted to ccommodte different heights. 8 of G-03 rev. E 04/17

9 7 Slide cle routing clips onto crossr. 8 Ly monitor fcedown on worksurfce G-03 rev. E 04/17 9 of 20

10 OPTIONAL: Insert stop screw to lock portrit/lndscpe monitor rottion. M4x 6mm 0 Loosely thred thum screws into mounting rckets. c Attch monitors to mounting rckets. 4x M4 x 10mm 4x M4 x 8mm M4 x 10mm 9 Cle Routing Plug power nd video cles into monitor y routing through cle clip. 10 of G-03 rev. E 04/17

11 Route cles through cle clips on side of riser. c Check cle lengths. Follow relief loop when routing cles. Mke sure there is enough cle. (10ft cle recommended) 10 Slide monitor onto crossr. NOTE: Monitor mounting rckets cn e instlled upside down to lower monitor 4" G-03 rev. E 04/17 11 of 20

12 Center totl width of mounted equipment on stnd. Tighten thum screws to secure monitors. 11 M3 x 6mm Attch end cps to crossr. 2mm Secure end cps to crossr. 12 of G-03 rev. E 04/17

13 12 Keyord nd Mouse cles Route mouse nd keyord cles through cle clips on side of riser. Follow relief loop when routing cles G-03 rev. E 04/17 13 of 20

14 13 Adjustment Step Importnt! You will need to djust this product fter instlltion is complete. Mke sure ll your equipment is properly instlled on the product efore ttempting djustments. This product should move smoothly nd esily through the full rnge of motion nd sty where you set it. If movements re too esy or diffi cult or if product does not sty in desired positions, follow the djustment instructions to crete smooth nd esy movements. Depending on your product nd the djustment, it my tke mny turns to notice difference. Any time equipment is dded or removed from this product, resulting in chnge in the weight of the mounted lod, you should repet these djustment steps to ensure sfe nd optimum opertion. Lift up nd down. WARNING STORED ENERGY HAZARD! DO NOT OPEN TOWER OR REMOVE SAFETY GUARD! A primry mechnism within the tower is under tension nd cn e hzrdous to people exposed to it under certin extreme conditions. DO NOT open the tower; DO NOT ttempt to service the crt/stnd. DO NOT remove sfety gurds or lels designed to protect or inform of possile hzrds. Only Ergotron-pproved instllers my service or otherwise modify crt/stnd. Filure to heed this Wrning my result in serious Personl Injury nd Dmge oth to the crt/stnd nd equipment mm Increse Lift Strength If the mounted weight is too hevy or this product does not sty up when rised, then you'll need to increse Lift Strength: Decrese Lift Strength If the mounted weight is too light or this product does not sty down when lowered, then you'll need to decrese Lift Strength: Lift up nd down. 4mm Adjustment my tke up to: 72 full 360 revolutions Increse Lift Strength If the mounted weight is too hevy or this product does not sty up when rised, then you'll need to increse Lift Strength: Decrese Lift Strength If the mounted weight is too light or this product does not sty down when lowered, then you'll need to decrese Lift Strength: Adjustment my tke up to: 115 full 360 revolutions 14 of G-03 rev. E 04/17

15 c Pivot djustment. 10mm Increse Lift Strength If the mounted weight is too hevy or this product does not sty up when rised, then you'll need to increse Lift Strength: Decrese Lift Strength If the mounted weight is too light or this product does not sty down when lowered, then you'll need to decrese Lift Strength: 14 Attch cps. NOTE: Align slot on cp with slot in mounting rcket when instlling cps G-03 rev. E 04/17 15 of 20

16 15 Test full rnge of motion Lift riser to highest position. Lower crossr into lowest position. NOTE: Leve enough slck in cle to llow full rnge of motion. Cution: To void the potentil to pinch cles it is importnt to follow the cle routing instructions in this mnul. Filure to follow these instructions my result in equipment dmge or personl injury. 16 of G-03 rev. E 04/17

17 16 Wrp cles nd fsten cle ties 17 Attch side pnels. 4x 18 Attch front pnel G-03 rev. E 04/17 17 of 20

18 19 Attch cp to top. 18 of G-03 rev. E 04/17

19 How to lign worksurfce to desk. Follow these instructions if worksurfce is not ligned to desk properly fter instlltion. Loosen clmp. Top View Rotte Worfi t-sr so tht worksurfce is prllel to front edge of desk. c Secure clmp to desk G-03 rev. E 04/17 19 of 20

20 Set Your Worksttion to Work For YOU! Lern more out ergonomic computer use t: Height Position top of screen slightly elow eye level. Position keyord t out elow height with wrists flt. Distnce Position screen n rm's length from fce t lest 20 (508mm). Position keyord close enough to crete 90 ngle in elow. Angle Tilt screen to eliminte glre. Tilt the keyord ck 10 so tht your wrists remin flt. To Reduce Ftigue Brethe - Brethe deeply through your nose. Blink - Blink often to void dry eyes. Brek 2 to 3 minutes every 20 minutes 15 to 20 minutes every 2 hours. For Wrrnty visit: For Service visit: For locl customer cre phone numers visit: NOTE: When contcting customer service, reference the seril numer Ergotron, Inc. All rights reserved. 20 of G-03 rev. E 04/17