Software Release Description. DOL 53x / DOL 634

Transcription

1 Sftware Release Descriptin DOL 53x / DOL 634 Recmmendatins Versin Build If upgrading a 2 huse cntrller frm a previus versin 4.x the cnnectins t terminal B2 and B15 must be mved. Nw terminal B2 is used fr huse 1. And terminal B15 is used fr huse 2. Knwn Issues Central exhaust variants are limited t 6 MultiStep s in this versin It is pssible t install install stepless tunnel fans in DOL 532 T, this is an errr and will be remved in a later versin. Changes and Errr Crrectins Stirfans are nt uninstalled after pwer failure Recmmendatins Versin Build If upgrading a 2 huse cntrller frm a previus versin 4.x the cnnectins t terminal B2 and B15 must be mved. Nw terminal B2 is used fr huse 1. And terminal B15 is used fr huse 2. Knwn Issues Central exhaust variants are limited t 6 MultiStep s in this versin It is pssible t install install stepless tunnel fans in DOL 532 T, this is an errr and will be remved in a later versin. Changes and Errr Crrectins When resuming after alarm when feed buffer is nt empty, it n lnger starts filling the next destinatin Alarms can nw be acknwledged frm FOX Shw cnnectin and IO allcatin is nw updated fr all changes t 'fans active at failure' state fr MultiSteps It was nt pssible t change the extra ventilatin temperature Manual cntrl f flaps n Heat Recvery Unit is fixed The standalne heater active Yes/N menu disappeared if N was chsen. S it was nt pssible t activate the heating again Sftware versin

2 2 Sftware Release Descriptin Recmmendatins Versin Build If upgrading a 2 huse cntrller frm a previus versin 4.x the cnnectins t terminal B2 and B15 must be mved. Nw terminal B2 is used fr huse 1. And terminal B15 is used fr huse 2. New Functins Knwn Issues Central exhaust variants are limited t 6 MultiStep s in this versin It is pssible t install install stepless tunnel fans in DOL 532 T, this is an errr and will be remved in a later versin. Changes and Errr Crrectins Number f decimals shwn when calibrating a bird weigher is increased frm 1 t 3 fr bird weigher 5 t 12. Is already 3 fr bird weigher 1 t 4. Destinatin feeding: If empty sensr is nt empty befre 30 minutes a Filling alarm is activated and cntrller is put t Pause state. Added missing aut/manual menu fr Flex heaters GUI: Crrected that return buttn can disappear when editing values frm the frnt page. Recmmendatins Versin Build If upgrading a 2 huse cntrller frm a previus versin 4.x the cnnectins t terminal B2 and B15 must be mved. Nw terminal B2 is used fr huse 1. And terminal B15 is used fr huse 2. New Functins All versins New USB Installer made fr prgram update. When inserting a USB stick the new installer will autmatically ppup Select prgram, push the green check mark and fllw the guide

3 Sftware Release Descriptin 3 Dynamic Air fr 1 zne, 2 zne and central exhaust Flr heating Water leakage supervisin and alarm Water reference curve can be adjusted. Spray cling renamed t Side cling (fr side mde) Nzzle cleaning added Pultry versins Flexible filling (filling f t small hppers pssible) Skip-a-day is silent (n filling/feeding n manual days) Feed separatin shutter can be installed if 2 r mre crss augers are installed (destinatin feeding) Flexible filling several filling perids with different amunts Added 24H clck, feed weigher and interval timers t frnt view. Feed supplement. Functin t add sea shells (pan r chain feeding). Natural Ventilatin Pig versins Wind angle limitatin handling added. Windward curtain psitin handling added. Climate nly versins: Supprt fr 1 24 hur clck and 1 water meter. Central exhaust Dynamic pressure cntrl fr central exhaust Dynamic MultiStep fr central exhaust Maximum f 4 flaps cntrls fr utlets (2+2 meaning 2 flap cntrls in each f the 2 stepless grups) Spraying functin CmbiDiffuse inlet added Behaviur cntrl added Knwn Issues Central exhaust variants are limited t 6 MultiStep s in this versin It is pssible t install install stepless tunnel fans in DOL 532 T, this is an errr and will be remved in a later versin. Changes and Errr Crrectins Day number synchrnizatin culd happen if a climate + prductin cntrller is set t use nly climate. Incrrect behavir f inspectin light in manual mde Litter quality is nw nly available in a Briler versin Feed demand sensr is nw read crrectly. A new Feed selectin mde is added. The mde is used t chse between the existing mde(per Destinatin) where a feed type fr each destinatin is set, and a fixed feed type per animal. When this mde is selected a feed type/mix can be selected fr all female destinatins and anther feed type/mix can be selected fr all male destinatins. Temperature selectin text 'DOL 15/114' is changed t 'DOL 114'

4 4 Sftware Release Descriptin Heat recvery cleaning: the part made by the heat recvery unit befre cleaning is ignred during cleaning. This is made t secure against lw temperature during cleaning if the same ventilatin demand was mved t side utlets. Humidity ventilatin in pure tunnel culd be kept high (up t 30%) even thugh the humidity was belw set pint. Minimum ventilatin curve was nt visible in pure tunnel setup Catching is n lnger reset after rebt r pwer lss. Furthermre uninstall then install is always perfrmed when changing install type (buttn->key->buttn). FarmOnline: AirSpeed and ventilatin was nt disabled in sidemde / tunnel mde Zne cntrlled inlet is nw als wrking within Heat Recvery Unit ventilatin mde. If alarm "N feed t feed weigher" is activated the sil auger stp in "Stp time sil auger" and then reactivate in "Runtime sil auger". In cmbi tunnel systems with Dynamic MultiStep r FreeRange installed the tunnel fans wuld nt run crrect. Manual allcatin f utside temperature allcatin is n lnger shwing 0-10 vlt inputs as an ptin Weather statin culd nt be installed as DOL 58 Added ppup t alarm lg. Press n an alarm t see the details Trend curve n Pressure in Central Exhaust Spray cling is renamed t 'Side cling' Sftware update stability increased Faster USB stick munt/unmunt Imprved CAN cmmunicatin Simplified time synchrnizatin s nly NTP server needs t be cnfigured Fixed s SD card is n lnger cnsidered bad when writing large files. As a cnsequence f this fix the EMERGENCY MODE has been drpped. Prgram update n lnger available via nrmal user interface (new prgrams will be delivered with a prgram updater n the USB stick) Fixed errr with feed mixture and feed mixture 1, enable handler crrected. Calibratin f relay cntrlled winch mtrs will nw always pen the flaps. Sme settings f manual stepless-t-step culd cause rebts every minutes. Autmatic sil change when using electrnic sils has been crrected. If an autmatic bird weigher is selected the user can nw select Inspectin weight instead f manual weight. "Tip weigher lg" renamed t "Feed cunter" and "Tip weigher impulse" renamed t "Weigher impulse" When restring settings then it will als restre the active sils. Crrected that destinatin feed hangs if resume and skip next destinatin. Added "Prgram descriptin" t CPU mdule menu All bird weigher search limits are set t 10 % when a Breeder versin is defaulted All bird weigher crrectin factr values are set t 100 % when a Breeder versin is defaulted. Added reference values fr water if briler (ROSS As hatched) If the sil auger is stpped because f a functin in the cntrller, it is shwn in the menu line "Feed supply state" Crrected refill f destinatin feeding

5 Sftware Release Descriptin 5 Netwrk setup was nt wrking Shutter cntrl fr shared weigher has been updated t set crrect psitin if in manual mde. CO2 sensr ptin is nw in-depended f the variant parameter f the CO2 minimum ventilatin cntrl We nly disable Dynamic Air cntrl mde if NO dynamic Air is active. Natural ventilatin des nw supprt half huse brding Minimum air speed is n lnger viewed in pure tunnel setups (like DOL 532 T). In stead the setting 'Stp cycle timer' is viewed. Crrected that ghst bjects are created when pulling a cntrller int FarmOnline. Egg cunters can use I/O cards type 15 and type vlt cntrl f tunnel stepless is wrking Remved prblem with climate cntrllers that subscribed t prductin bjects and gt bjects (but a prductin cntrller n a similar netwrk will still be trubled by many bjects) In 2-huse cntrllers the use f Main I/O bard terminal B2 and B15 is crrected. Nw huse 1 uses terminal B2. And huse 2 uses terminal B15. Recmmendatins New Functins DOL 532T variant Versin Build Pressure cntrl is ptinal in tunnel mde Calibratin f relay cntrlled winch mtrs withut feedback is nw made n a specified time f day Qwerty keybard intrduced fr entering texts (huse name, file names etc) Feed separatin shutter fr destinatin feedingnew mde fr shared Feed weigher: Shared withut shutter. Only pssible t select when destinatin feeding. Knwn Issues Changes and Errr Crrectins A ttal f 8 time hur clcks fr breeder sftware Relay cntrlled winch mtrs withut feedback: Maximum runs befre calibratin f can be 999 Calibratin is dne t the clsest end psitin (calibrating t clsed if pening is less than 50%, else calibratin ges t fully pen) An explanatin text is added t the ppup dialgue Emergency pening, like Emergency pening, high temperature / Emergency pening, high humidity It is nw pssible t selected the same icn n different pages when cnfiguring user views. Fixed errr: Mre sils with the same feed type are selected after a change frm Drum weigher t electrnic sil weigher. Master passwrd did nt wrk

6 6 Sftware Release Descriptin Preheating setpint culd nt be adjusted in batch stp mde Negative Pressure Adjustment with active pressure set-up is simplified t use nly 1 curve Default values fr Dynamic multistep changed frm 5 5 vlt t 10 0 vlt (fr fan stpped running maximum) Heat recvery cleaning: the ventilatin part made by the heat recvery unit befre cleaning is ignred during cleaning. This is made t secure against lw temperature during cleaning if the same ventilatin demand was mved t the side utlets. Recmmendatins New Functins 2 huse cntrller Flr heating Reference curves fr Pigs Minimum ventilatin in percent Versin Build Daily/advanced user screens are replaced by ne level user screens that can be activated frm the frnt The user screens are autmatic set t large icns if 6 r less icns are selected t the screen small icns if 7 t 16 icns are selected t the screen The lk f the icns are changed t a flat design Sftware versin is available in the first level f the service menu User interface is updated t a flat icn design and general layut changes t header, text clr and etc. Adjusted eggs functin added Discarded eggs functin added Litter quality functin added New mde fr shared Feed weigher: Shared withut shutter. Only pssible t select when destinatin feeding. Knwn Issues The frnt screen will smetimes shws three small icns where it shuld shw 3 large icns Changes and Errr Crrectins I/O allcatin f flaps did nt wrk crrectly in a 2 huse cntrller Fixed update prblem (remved splash screen cmmand) Upgrade is nw pssible n CPU mdules befre versin I

7 Sftware Release Descriptin 7 New Functins Versin Build Optin t manually enter discarded eggs (breeder versin) Optin t enter adjusted eggs and litter quality Optin t use cling relay fr humidificatin Side cling can be started befre maximum ventilatin, if utside temperature is abve the set pint fr the huse PI cntrl intrduced n side cling Catching mde By a turnkey r a menu buttn Timing settings t stp feeding, set windw fr activatin Settings fr ventilatin system during catching Settings fr feeding, light during catching Added supprt fr DOL 58 weather sensr Relay heat is synchrnized with cycletimer n minimum inlet psitin Minimum airspeed in tunnel is made as a batch curve User ffsets added t climate and prductin menu s fr all setpint including a batch curve Added 2 mre 24 hur clcks t Breeder Added 24 hur clck setting stp n time. The setting is user selectable t be set either t "n time" (relative) r "stp time" (abslute). Feed eaten by dead birds are calculated. Calculatin f feed / animals crrected fr feed eaten by birds that are nw dead. Calculatin f weight f all birds added. New matrix t supprt stp time in 24 hur clck. Added individual search limits fr bird weighers Knwn Issues Tunnel cling type, mde and rati s must be checked after an upgrade. Type must be set t PAD r SPRAY, this is new t versin 3.0. The default setting is PAD, which is the mst used tunnel cling type. But this type reset the mde t parallel. Mde must be set t parallel r sequence (sequence is nly available if type is spray). Rati f each tunnel cling relay must be checked/set. NOTE regarding heat recvery unit: When updating frm a versin 1.x r 2.x the negative pressure curve fr heat recvery unit must be set manually (because the curve structure has changed) In between functins d nt activate the crrect ventilatin demand if heat recvery unit is set t active Changes and Errr Crrectins Side cling can be synchrnized with minimum inlet cycle timer

8 8 Sftware Release Descriptin If synchrnizatin f humidificatin r cling is active they are als kept OFF until delay time has elapsed (they culd g ON if the demand was high enugh). Humidificatin is nw stpped if temperature is belw heat setpint (it was ventilatin setpint befre). Tunnel cling will start up with a (cnverted) side cling demand if desert cntrl is active. Cnversin rate is 3:1 When switching frm Natural mde t side r HRU the starting ventilatin demand in side/hru is set 25% r 75%. If Natural is stpped because f lw utside temperature the side ventilatin demand will be 25%. If Natural is stpped because high utside temperature r high CO2 the side ventilatin demand will be 75%. Hysteresis n the natural ventilatin inlets and utlets are nw wrking as +/- hysteresis, s that they dn t mve n every sample. After a pwer fail Pan feeding and Chain feeding will wait fr the crss augers t fill befre starting. Dynamic MultiStep signals (0-10 vlt and stp relays) culd nt be cntrlled in manual In BASIC mde the pressure cntrlled inlets was nt cntrlled during crrect during minimum ventilatin. They are nw cntrlled accrding t pressure with active fans and clsed with fans stpped. In sme situatin winch mtrs wuld change psitin frequently up and dwn arund the required psitin (due t flat cmpare withut hysteresis) Tunnel cling 'blcked by' infrmatin is set t temperature if cntrl frm is by temperature and the airspeed (temperature) is t lw. Default value fr CO2 cntrl is ppm as in versin 3.0 Text fr weather statin 'ffset t nrth' is changed t 'ffset frm nrth' Daynumber culd increase by 2 at nidnight Tunnel cling setup as 'based n air speed' started t early if the user had reduced maximum airspeed. In that case the cling wuld start n the user set maximum airspeed, even if cling start speed was higher. Drum weigher and DOL 9940 has been ptimized fr speed. Feed weighing with DOL 99B is nw just as quick as a with a DOL 95. Minimum ventilatin curve is was visible in pure tunnel setup Day number synchrnizatin culd happen if a climate + prductin cntrller is set t use nly climate (i.e. the day number culd change t a false day number every hur). In cmbi tunnel systems with Dynamic MultiStep installed the tunnel fans wuld nt run crrect. New Functins Versin Build Knwn Issues Tunnel cling type, mde and rati s must be checked after an upgrade. Type must be set t PAD r SPRAY, this is new t versin 3.0. The default setting is PAD, which is the mst used tunnel cling type. But this type reset the mde t parallel. Mde must be set t parallel r sequence (sequence is nly available if type is spray). Rati f each tunnel cling relay must be checked/set.

9 Sftware Release Descriptin 9 Negative pressure curve fr heat recvery unit must be set after an upgrade. When updating frm a versin 1.x r 2.x the negative pressure curve fr heat recvery unit must be set manually (because the curve structure has changed) Feed, water and light prgrammes If a prgram must end at midnight then prgram it t end 24:00 and nt 00:00 Lacking translatin f new functins (they will be shwn in English) Prductin alarm relay Lad stepless fan settings Adjustment f dimmed backlight level Changed setup f preheating Water/feed last week Humidificatin stp day It requires BigFarmNet Manager 3.1 r newer t display the ventilatin mde prperly. Changes and Errr Crrectins Tunnel cling setup as 'based n air speed' started t early if the user had reduced maximum airspeed. In that case the cling wuld start n the user set maximum airspeed, even if cling start speed was higher. Versin Build New Functins FreeRange functinality as part f MultiStep system (with natural / active fans) Breeder variant supprts up t 24 water meters (r same number as available destinatins) Weather statin as ptin Prductin alarm relay as ptin Pssibility t lad settings fr stepless fan curves Lad settings frm USB can be dne as Settings alne User views alne Bth user views and settings Optin t stp humidificatin after a specific day number Synchrnizatin f humidificatin with fans during cycle timer n side inlets Desert cntrl n tunnel cling: If side cling is active befre start f tunnel mde pads can be rinsed Effect curve intrduced t linearize the pad cling Added pssibility t adjust the dimmed backlight intensity

10 10 Sftware Release Descriptin Knwn Issues NOTE regarding heat recvery unit: When updating frm a versin 1.x r 2.x the negative pressure curve fr heat recvery unit must be set manually (because the curve structure has changed) Feed, water and light prgrams If a prgram must end at midnight then prgram it t end 24:00 and nt 00:00 Lacking translatin f new functins (they will be shwn in English) Prductin alarm relay Lad stepless fan settings Adjustment f dimmed backlight level Changed setup f preheating Water/feed last week Humidificatin stp day If the cntrller cannt see an USB stick, the prblem can be reslved by switching pwer ff and n. The symptm are that the USB is detected but n munted r unmuted message is displayed. It requires FarmOnline Explrer 3.1 r newer t display the ventilatin mde prperly. Changes and Errr Crrectins The batch curves can perate with negative numbers, t be used fr prestart/preheating Minimum ventilatin by CO2 is n lnger limited t 25% f curve value the first 10 days f the batch The name f the functin Night setback is changed t Day-and-night adjustment. It is made harder t restre t factry settings (s that it is dne in the same way as batch end/start). This is changed t secure against unwanted defaults. The filling settings (matrix) is nw available fr the advanced user view Individual egg cunters can nw be selected fr the advanced user view FarmOnline cnnectin is made mre rbust The pssibility fr setting up the cntrller as nly a climate r prductin cntrller is re-intrduced Humidity ventilatin culd exceed maximum ventilatin (if added up with temperature ventilatin, alne it did nt exceed max ventilatin) Remved false alarms n tunnel cling pump Zne cntrlled side inlets are n lnger left pen in tunnel mde Humidificatin set pint cannt be clser than 5 %RH t the humidity set pint Fixed errr where advanced cmfrt was nt added t the heat setpint Stir fans nw wrk with Huse Heaters with individual sensr Reset t default is nw resetting language t English Passwrd timeut is changed t 1 minute after user view (daily r advanced) has been activated Passwrd level is remved fr all nne edit user menus (Climate, Prductin, Management and Alarm). Passwrd level fr user menus (climate, prductin, management, alarms) are changed. Climate, prductin, management in general t daily user, with a few having n passwrd (dead birds) and sme mre advanced user settings having advanced user level. Alarms t advanced user.

11 Sftware Release Descriptin 11 Passwrd level fr technical menus (Setup, Calibratin, Service infrmatin, Service, Use passwrd) are changed Service, Service infrmatin, Manual/Aut t advanced user level Remaining technical menus are set t Service level Cleaning prgram fr heat recvery unit includes 3 prgrams with 1-3 starts in each prgram Menus fr pre heating are changed, t Pre heating setpint Pre heating at batch stp Negative pressure curve fr heat recvery unit is changed t Ventilatin HRU demand Tunnel utlets can mdulate during side mde (used with lw ventilatin in huse with few r nne fans in side mde) Limitatin f CO2 ventilatin is changed frm 1.0 belw heat set pint t 2.0 in rder t give the heat cntrl mre rm t perate and keep the temperature up Smetimes chain feeding wuld nt start Hysteresis fr leaving tunnel is changed frm 2 t 1 C. This is changed t reduce the factr f duble hysteresis n tunnel start and stp. Chill effect is nw 0.0 C with inside temperatures at 38 C r mre Upgrade f sftware prblems slved If a USB stick with a prgram update is nt bt ice frmatted, the cntrller will ask if it shuld frmat the USB stick but did nt frmat the USB crrectly Detectin f USB stick is imprved SDK updated t handle early hardware versin (befre revisin I) Feed update frm an electrnic sil r day sil was nt registered, after the destinatin target was reached. When target is reached feed demand is remved and the sil system recalculates the cnsumptin made. Light dimmer did nt wrk in manual mde Default value fr CO2 cntrl is changed t a P band f ppm Heat recvery cleaning prgram fixed, it did nly use prgram number 1 Heat recvery unit did nt pen side inlet during anti icing if 'Use side curve fr side inlets' was selected Pressure cntrl in basic mde with cycling fans Versin Build Knwn Issues Water prgram des nt wrk if start time is higher than stp time. Changes and Errr Crrectins Negative pressure curve fr tunnel culd nt be adjusted. If the inlets fr frnt / rear was installed as analgue their minimum/maximum vltages culd nt be adjusted (they was fixed n 0 and 10 vlt).

12 12 Sftware Release Descriptin New Functins Versin Build Full integratin f breeder data with FarmOnline Added climate reference settings fr breeder and briler Daily/Advanced views are nw saved s upgrades t newer versins will restre the views. When upgrading t this versin the daily/advanced are nt restred Restre f User Views are nw pssible frm versin t versin ( n supprt fr settings frm versin 1.5, 1.6, 2.0 r 2.1) Time cntrlled feed weight nw handles sil empty sensr. Time cntrlled feed weight is nw able t give an alarm fr "N feed t feed weigher". Sil empty sensr is handled s that the sil auger is nt set if the sensr is empty. Added buttn fr aut zm t trend curves Knwn Issues Water prgram des nt wrk if start time is higher than stp time. Negative pressure curve fr tunnel cannt be adjusted Minimum/maximum vltages fr analg cntrlled inlets can nt be adjusted in 2 zne setups, they are fixed n 0 and 10 vlt. Changes and Errr Crrectins In sme situatins extra ventilatin wuld nt start (typically if spray cling was started befre first extra ventilatin step) Save and restre settings frm SD card culd read wrng settings. Chain feeding wuld nt always wrk crrectly if the start time was at 0:00 r the feeding perid crsses midnight. Egg cunter trend graph was nt wrking. Destinatin feeding: If mre sils was installed with the same feed type, it wuld always take frm the sil with the highest number, instead f the sil that was selected. All feed weighers (except DOL 99B and DOL 9940): If mre sils was installed with same feed type, then when selecting Autmatic change, the parameters fr setting time and amunt fr the change, culd nt be seen. Cmfrt and chill factr is nw available fr daily and advanced user menu's It is nw pssible t specify the actual sex f the birds in bth Briler and Breeder (in the Setup / Adjustment / Prductin menu). Feed ffset can nw be adjusted with a precisin f 0.1 g / bird The rder f culled reasns has been adjusted s the mst frequently used culled reasns are at the tp I/O Type 6 and I/O Type 7 nly wrks n psitin 1 t 6, s it is fixed s they cannt be selected n psitin 7 and upwards. It is nw pssible t enter Inspectin weight if a manual bird weigher is installed tgether with an electrnic bird weigher

13 Sftware Release Descriptin 13 The feed clumn in the Destinatins setup menu in Setup / Adjustment / Prductin has been remved it is available in the Prductin / Filling / Destinatins menu Default values fr prductin alarms has been adjusted t better match what is required in typical installatins Fix f autmatic sil change frm sil 2 t sil 1 Nightly backup f settings has been fixed and the settings can be restred using Technical / Service / Settings / Restre settings frm backup. Fix s PC Sim (the PC simulatr) d nt crash when IO type 6 and IO Type 7 are selected. Shw cnnectin has been fixed s fr IO Type 10 it is nw shwn when an external resistr is required. Versin Build Recmmendatins Custmers with versin Build 72 r Build 16 shuld upgrade t this versin. The errr fixed in this versin was intrduced in versin Build 72. Knwn Issues In a simple prductin variant (P variant) it is nt pssible t install a light sensr. Changes and Errr Crrectins Fixed alarm fr N feed t feed weigher. Trend menu fr Water 24h is crrected (Management/Trend curves/prductin/water 24h) Trend menu fr Feed 24h is crrected (Management/Trend curves/prductin/ Feed 24h) Versin Build New Functins ServiceAccess frm FarmOnline t cntrller. Access the cntrller s user interface. New variant fields fr Breeder: Max number f destinatins and max number f egg cunters. Knwn Issues Trend menu fr Water 24h des nt wrk (Management/Trend curves/prductin/water 24h) Trend menu fr Feed 24h des nt wrk (Management/Trend curves/prductin/ Feed 24h) Changes and Errr Crrectins Chain feeding resumes a running chain feeding after a pwer failure. Light cntrlled by sensr crrected. Installatin and setup f shared sils crrected HRU cleaning is nt active in batch stp.

14 14 Sftware Release Descriptin Versin Build New Functins OEM variant structure implemented (name in the header f the cntrller DOL 539 / OEM) Versin Build New Functins Climate features: Batch start day can be changed frm -1 (t e.g. -5 fr pre heating, 126 fr breeders) Available MultiStep increased frm 14 t 16 Prductin (breeder) features Same new features as Briler except it nly supprt 6 water meters. Destinatin feeding can increase feeding amunt next day after a manual day. DOL 9940 can be used fr destinatin feeding Destinatin feeding can be paused / resumed / resumed and skip current destinatin 2 feed mix can be setup fr destinatin feeding (if drum scale r DOL 9940). 32 Egg cunters. Manual entering eggs (flr eggs and system eggs). 6 generic manual entering s (name, unit can be selected) 6 24 hur clcks 6 slave lights 6 Interval timers fllw a prgram (main light, slave light 1 6, 24 hur clck 1 6) Changes and Errr Crrectins Feed mixing adjustments was reset after pwer failure Offset t number f chain runs was set t 0 after a pwer fail Changes and Errr Crrectins Versin Build Errr crrectin n heating: heating culd be blcked by a zer ventilatin demand that was nt actual zer (runded ff t smething extreme clse t zer, but nt zer) The applicatin fr lgging data t trend curves, water alarms etc. culd be exhausted and after that stpped

15 Sftware Release Descriptin 15 Recmmendatins Versin Build If the existing DOL 535/539 is used fr destinatin feeding, it is imprtant t avid an update t this SW, as the SW des nt include supprt fr destinatin feeding. New Functins Climate features Heat recvery unit supprt Dynamic MultiStep supprt Prductin features Knwn Issues 5 sils (previusly 4 sils was supprted) Alarm fr empty sil (using a sensr) Cmbine feed weigher and sil weiger Shared sil tw huse may use the same sil an the actual cntent can be read n bth cmputers Alarm is feed cnsumptin decreases 24 water meters supprted Imprved water leakage alarms Inspectin light Dawn/dusk has gained an extra level Light surces can be named by the user Bst feature t supprt ld light systems Light intensity cntrlled by a sensr Destinatin feeding: Destinatin feeding will n lnger be available in this versin f the sftware. Ultim 2013 a new DOL 535/539Breeder cmputer is launched which include supprt fr 24 destinatins and 3 crss augers.

16 SKOV A/S Hedelund 4 Glyngøre DK-7870 Rslev Tel Fax skv@skv.dk