MODELS. 2 & 4 Versions. SUITABLE FOR WET LOCATIONS in the following locations or unclassified locations:

Size: px

Start display at page:

Download "MODELS. 2 & 4 Versions. SUITABLE FOR WET LOCATIONS in the following locations or unclassified locations:"

Catherine Weaver
6 years ago
Views:

INSTALLATION AND MAINTENANCE MANUAL Explsin Prf Lw Prfile Linear LED Light EPL-24-50LED Series MODELS 2 & 4 Versins SUITABLE FOR WET LOCATIONS in the fllwing lcatins r unclassified lcatins: Fr Use

1 INSTALLATION AND MAINTENANCE MANUAL Explsin Prf Lw Prfile Linear LED Light EPL-24-50LED Series MODELS 2 & 4 Versins SUITABLE FOR WET LOCATIONS in the fllwing lcatins r unclassified lcatins: Fr Use In: Class I, Divisin 1 & 2 Grups C, D Temperature Cde: T5 fr 2' mdel, T4A fr 4' mdel Ambient Temperature Range: -40C t +65C These instructins cntain imprtant safety infrmatin, read and fllw them carefully. Larsn will nt accept any respnsibility fr injury, damage r lss which may ccur due t incrrect installatin, peratin r maintenance 1: Intrductin This Linear LED light is designed fr illuminatin f industrial lcatins. It uses the latest in slid state lighting technlgy fr lng life, lw maintenance, and high efficiency. The unique ptical design fcuses light dwnward t where it is needed, giving imprved efficiency ver a cnventinal HID luminaire. An internal, universal input, pwer-factr-crrected switch-mde supply allws it t be used frm any nminal 100V-277V, 50/60Hz AC supply withut any variatin in light utput. Nte: Save these instructins fr future reference. Larsn Electrnics, LLC Phne: (800) f 7

2 2: Installatin T avid the risk f fire, explsin, r electric shck, this prduct shuld be installed, inspected, and maintained by a qualified electrician nly, in accrdance with all applicable electrical cdes. Cnduit seal fittings are required within 6 f the wire bx entrance in bth Divisin 1 and Divisin 2 lcatins. T avid electric shck: Be certain electrical pwer is OFF befre and during installatin and maintenance. Luminaire must be cnnected t a wiring system with an equipment-grunding cnductr. T avid explsin: Make sure the supply vltage is within the luminaries vltage rating. Ensure the marked T Rating is less than the ignitin temperature f the Hazardus Atmsphere. D nt perate in ambient temperatures abve thse indicated n the Luminaire nameplate. D nt perate if the lens is cracked r damaged. All fasteners shuld be prperly seated. WARNING - EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2, CLASS II DIVISION 1. AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTIOND E COMPOSANTSP EUTR ENDRE CE MATERIEL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION 1, CLASSE II, DIVISION 1. T avid explsin (Cntinued): EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE DECONNECTER L'EQUIPEMENT, COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX DO NOT let pwer crd tuch ht surfaces DO NOT munt near gas r electric heaters Equipment shuld be munted in lcatins and at heights where it will nt be subjected t tampering by unauthrized persnnel. The use f accessry equipment nt recmmend by the manufacture may cause an unsafe cnditin DO NOT use this equipment fr ther than intended use Larsn Electrnics, LLC Phne: (800) f 7

3 The technical data indicated n the Luminaire are t be bserved. Changes t the design and mdificatins f the Luminaire are nt permitted Only genuine replacement parts are t be used when unfreseen maintenance is required. Cnsult factry at r authrized representative as required. Fr supply cnnectins use wire rated fr at least 90ºC Cnduit thru Munt (Figure 2) Installatin Steps: Fr maximum lng term reliability and light utput, the light must be installed in free air. The Linear fixture design incrprates an ver-temperature cntrl circuit that reduces input pwer shuld internal temperatures reach a maximum level. In this event, light utput may be reduced. The Linear fixture is threaded fr 3/4 NPT, at the center and each end f the Pwer Supply Husing, in rder t be assembled t cnduit. Attach cnduit as shwn in figure 2. Use an electrically cnductive, crrsin resistant, pipe sealant (per the Natinal Electric Cde) fr all fittings and cnduit. Install required seal fittings within 6 f the wire bx entrance. Seal fittings are required in bth Divisin 1 and Divisin 2 lcatins. Larsn Electrnics, LLC If there is misture present, r chance f it, in the cnduit system then necessary precautins shuld be taken by the installer t prevent the misture frm entering thru the cable r cnduit and entering the fixture. Failure t cmply with the abve culd vid factry warranties. Fixture is factry wired fr bth Pendant and thrugh wiring. Remve the Pwer Supply cver t attach incming pwer t the white wire and black wire leads with wire nuts at the end f the fixture. Attach the grund wire t the green grund lead supplied at the end f the fixture. Repeat this prcedure fr the ppsite end. Ensure that the -rings are prperly seated in the grves; reattach the Cver using the screws previusly remved. Tighten all screws t 40 in/lbs (4.52Nm) Cnnect incming pwer as fllws: Green t Safety Grund using green grund lead supplied at the end f the fixture. Neutral t white Line t black Restre pwer and verify peratin. See Figure 2. Phne: (800) f 7

Figure 2. Anti-rtatin Screws Sealing Fittings Cnduit Pendant Munt (Figure 3) Installatin Steps: Fr maximum lng term reliability and light utput, the light must be installed in free air.

4 Figure 2. Anti-rtatin Screws Sealing Fittings Cnduit Pendant Munt (Figure 3) Installatin Steps: Fr maximum lng term reliability and light utput, the light must be installed in free air. The Linear fixture design incrprates an ver-temperature cntrl circuit that reduces input pwer shuld internal temperatures reach a maximum level. In this event, light utput may be reduced. The Linear fixture is threaded fr 3/4 NPT, at the center and each end f the Pwer Supply Husing, in rder t be assembled t cnduit. Attach cnduit as shwn in figure 3. Use an electrically cnductive, crrsin resistant, pipe sealant (per the Natinal Electric Cde) fr all fittings and cnduit. Install required seal fittings within 6 f the wire bx entrance. Seal fittings are required in bth Divisin 1 and Divisin 2 lcatins. WARNING : If there is misture present, r chance f it, in the cnduit system then necessary precautins shuld be taken by the installer t prevent the misture frm entering thru the cable r cnduit and entering the fixture. Failure t cmply with the abve culd vid factry warranties. Fixture is factry wired fr bth Pendant and thrugh wiring. Remve the Pwer Supply Cvers t attach incming pwer t the white wire and black wire leads with wire nuts at the center f the fixture. Attach the grund wire t the green grund lead supplied at the center f the fixture. Ensure that the -rings are prperly seated in the grves, reattach the Cver using the screws previusly remved. Tighten all screws t 40 in/lbs (4.52Nm). Restre pwer and verify peratin. See Figure 3. Larsn Electrnics, LLC Phne: (800) f 7

Figure 3. Sealing fitting Anti-rtatinal Screw Pwer Supply Cver 3: Maintenance T avid persnal injury, discnnect pwer t the light and allw the unit t cl dwn befre perfrming maintenance.

5 Figure 3. Sealing fitting Anti-rtatinal Screw Pwer Supply Cver 3: Maintenance T avid persnal injury, discnnect pwer t the light and allw the unit t cl dwn befre perfrming maintenance. N user serviceable parts inside f fixture. Risk f electric shck. Remval f the lens will vid the warranty. See Figure 4. 1) We suggest perfrming visual, mechanical and electrical inspectins n a regular basis. We suggest rutine checks t be made n a yearly basis. Frequency f use and envirnment shuld determine this. It is recmmended t fllw an Electrical Preventive Maintenance Prgram as described in NFPA 70B: Recmmended Practice fr Electrical Equipment. 2) If the lens (Figure 4 belw) requires peridical cleaning t ensure cntinued phtmetric perfrmance. Clean the lens with a damp, nn-abrasive, lint-free clth. If nt sufficient, use mild sap and water. 3) Inspect the utside f the Luminaire husing t ensure that they are free f any bstructins r cntaminatin (i.e. excessive dust build-up). Clean with a nn-abrasive clth if needed. 4) D nt perate if the lens is cracked r damaged. All fasteners shuld be prperly seated. 5) NOTE: Screws ther wiring cmpartments are factry trqued and shuld nt be tampered with during installatin r maintenance. Larsn Electrnics, LLC Phne: (800) f 7

6 Figure 4. Glass Lenses NOTE: Screws and Glass are NOT field replaceable Nminal AC Supply Vltage Pwer cnsumptin: 2 versin 4 versin Specificatins VAC, 50-60Hz 33W nminal 66W nminal Input Current: (Nminal) 0.4Amps 0.8Amps 0.15Amps 0.3Amps Operating temperature range -40 F t +149 F [-40 C t +65 C] 149 F [65 C] Pwer factr >0.9 ATHD <20% Dimensins (L x W x H) See Figure 5. Weight 12 lbs [5.44 kg] (2 ) 17 lbs [7.71 kg] (4 ), Intertek Certified t UL-844 and C22.2 N. 137 Larsn Electrnics, LLC Phne: (2 ft) (4 ft) (2 ft) (4 ft) 6 f 7

7 4: Chemical Cmpatibility Guide Ftnte n Chemical Cmpatibility Guide: The chemical cmpatibility data referenced in this manual was supplied by the raw material manufacturers and is intended as a general guide. The data represents the basic material prperties and des nt necessarily represent the perfrmance f the final prduct due t manufacturing prcess and design variatins fr each final prduct. Chemical cmpatibility is highly dependent n cncentratin, temperature, humidity, and ther envirnmental cnditins and therefre the custmer assumes respnsibility fr evaluatin f gaseus r direct cntact chemical cmpatibility at their site prir t prduct installatin. All statements, technical infrmatin and recmmendatins cntained herein are based n infrmatin and tests we believe t be reliable. The accuracy r cmpleteness theref is nt guaranteed. In accrdance with Larsn Electrnics, LLC Terms and Cnditins f Sale, and since cnditins f use are utside ur cntrl, the purchaser shuld determine the suitability f the prduct fr his intended use and assumes all risk and liability whatsever in cnnectin therewith Larsn Electrnics, LLC Phne: (800) f 7

Operating Instructions

Operating Instructions DurSite & SafeSite Area Light with Battery Backup Imprtant Infrmatin: These instructins cntain safety infrmatin, read and fllw them carefully. Dialight will nt accept any respnsibility fr injury, damage